Search Documents

By I. C. Spangenberg

The status of sampling practices in the gold mining industry in Africa was determined as an initial step in a process to standardize sampling practices in the mining industry. Twenty-one gold mines, twenty metallurgical plants, and thirteen laboratories were rated for the potential influence of the relevant sampling errors on each component of the particular sampling system. The findings of the study on the status of equipment, standards, procedures, and management principles were presented in a dissertation (Spangenberg, 20121) and are now used by AngloGold Ashanti?s mines in the quest for correct sampling practices. The information is also used to compile a guideline on leading practice procedures for sampling methods in gold mining. This article is an overview of sampling best practice found in African mining Keywords theory of sampling, best practise, sampling errors, sampling standards.

Jan 1, 2014

By A. V. Z. Brink

Rock engineering risk is defined in this paper as a function of the potential ground motion; the vulnerability of the workplace; exposure of people; and a general term – quality of information. The paper describes the development of prototype software that is a combination between an expert system approach for determining overall risk assessment, a risk control recommendation and a basic GIS (Graphic Information System) approach for graphically overlying input parameters and the output risk. The expert system uses a Bayesian probabilistic approach to combine various workplace-related information, a quantified seismological environment and the exposure of underground staff to provide an overall RE risk rating. The risk assessment is dynamic in that it is recalculated each time that any of the input parameters change, for example each time a seismic event is recorded in the area of interest. The code was tested on a data set from Savuka Gold. As risk assessment is not an absolute prediction of a specific outcome, it is therefore not possible to relate to individual case studies and the reliability of this method would only be determined after an extensive period of use with appropiate back-analysis. Le risque dans le génie minier est défini dans cette étude comme une fonction du mouvement potentiel de terrain ; la vulnérabilité du lieu de travail ; l’exposition des personnes ; et un terme général – la qualité de l’information. L’étude présente décrit le développement d’un logiciel prototype qui est une combinaison entre une démarche de système expert pour déterminer une évaluation générale du risque, une recommandation pour le contrôle du risque, et une démarche de SIG (Système d’Information Géographique) pour superposer graphiquement les paramètres d’entrée et le risque de sortie. Le système expert utilise une méthode de probabilité bayésienne pour combiner des informations variées sur le lieu de travail, des données quantifiées sur l’environnement sismique, et l’exposition du personnel travaillant sous terre, pour finalement produire un classement général de risque minier (RE). L’évaluation du risque est dynamique en ce sens qu’elle est recalculée à chaque fois qu’un des paramètres d’entrée change, par exemple à chaque fois qu’un évènement sismique est enregistré dans la région. Le code fut testé sur un ensemble de données obtenues de Savuka Gold. Comme l’évaluation du risque ne constitue pas une prédiction absolue d’un résultat spécifique, elle est par conséquent difficile à rattacher à des cas individuels et la validité de cette méthode ne pourrait être déterminée qu’après une longue période d’utilisation avec analyse rétrospective appropriée. Das Gesteinstechnikrisiko wird in dieser Arbeit als Funktion einer möglichen Bodenbewegung definiert; die Anfaälligkeit des Arbeitsplatzes; das Ausgesetztsein der Belegschaft; und ein genreller Begriff - Qualität der Informationen. Das Papier beschreibt die Entwicklung einer Prototyp-Software, die eine Kombination zwischen einem Expertensystemzugang für die Bestimmung der gesamten Risikobeurteilung ist, eine Empfehlung zur Risikokontrolle und eines fundamentalen GIS (graphisches Informationssystem) Zuganges für graphisch darüberliegende Eingangsparameter und das Outputrisiko. Das Expertensystem verwendet eine bayesische Wahrscheinlichkeitsannäherung, um verschiedene mit dem Arbeitsplatz in Verbindung stehende Informationen, ein quantitativ bestimmtes seismologisches Umfeld und das Ausgesetztsein des Untertag-Personals zu kombinieren, um eine gesamte RE-Risikobewertung zur Verfügung zu stellen. Die Risikobeurteilung ist insoferne dynamisch,daß sie stets nachkalkuliert wird wenn sich irgendeiner der Eingangsparameter ändert, z.B. jedesmal wenn ein seismischer Fall im Interessensbereich aufgezeichnet wird. Der Code wurde auf einem Datenbestand von Savuka Gold geprüft. Da die Risikobeurteilung nicht eine absolute Vorhersage eines spezifischen Resultates ist, es ist folglich nicht möglich, sich auf einzelne Fallstudien zu beziehen und die Zuverlässigkeit dieser Methode könnte nur nach einer umfangreichen Benutzungsdauer mit geeigneter Postanalyse bestimmt werden.

Jan 1, 2003

By R. Poisel, C. Scavia, Preh A., W. Roth, M. Pirulli

ABSTRACT: Two methodologies for the three-dimensional simulation of the run out of rock avalanches are presented: one based on a granular approach and the other based on a continuum equivalent approach. An evaluation of the possible run out area of the Oselitzenbach landslide (Carnic Alps, Austria) has been carried out applying the two methodologies. The combined use of these two approaches makes it possible a comprehensive assessment of the run out area. RESUME: Deux méthodologies pour la simulation tridimensionnelle de la propagation des avalanches rocheuses sont présentées: la première est basée sur un modèle de type granulaire et la deuxième sur un modèle du continu équivalent. Une évaluation de la propagation éventuelle de l’avalanche de Oselitzenbach (Alpes Carniche, Autriche) a été réalisée en utilisant les deux méthodologies. Les résultats obtenus montrent que la combinaison des deux approches rend possible une analyse plus complète de la phase de propagation. KURZFASSUNG: Für die dreidimensionale Modellierung eines Felsmassensturzes (sturzstrom) werden zwei Methoden, eine granulare und eine kontinuumsmechanische Methode, vorgestellt. Beide Methoden wurden zur Abschätzung der Ausbreitung (runout) der Massenbewegung Oselitzenbach (Karnische Alpen, Österreich) herangezogen. Die kombinierte Anwendung beider Methoden ermöglichte eine umfassende Beurteilung des möglichen Ausbreitungsbereichs.

Jan 1, 2003

By A. M. Hearn, J. G. Roos

Energy consumption, being a large proportion of the input of the ferroalloy production process, can be measured in terms of the efficiency with which the energy is utilized and the effectiveness with which it is used. The efficiency of the usage of energy revolves around the specific consumption of the energy for the production of the alloy, which encompasses the thermodynamic aspects of the process and is more of a metallurgical function that will not be addressed further in this paper. The effectiveness with which the energy is utilized is determined by the optimisation of the electricity supply from the utility (in this case Eskom). The South African electricity supply industry is on the brink of considerable restructuring, implying changes in ownership, structure and regulation. In other countries, however, restructuring has often seen higher prices. Owing to the diversity of growth prospects in South African markets, Eskom is turning to new market management and generation strategies. In future, Eskom will develop pricing strategies to increase demand from attractive customer segments such as paper & pulp, iron & steel, aluminium, and other metallurgical industries. There will be a broader spectrum of product offerings, including dynamic pricing options and demand-side management incentives. In a future electricity market that will become more dynamic and demanding, it will become increasingly important for electricity consumers to optimise their electricity supply. There are many facets in optimising the electricity supply, which include optimal utilisation of the tariff, integrating energy cost management into the production planning process, implementation of demand-side management actions, modelling, scenario planning (.what-ifs?.), optimisation, maintenance scheduling coordinated with the tariff periods, etc. This paper gives consideration to the status of the development of technology at the manganese alloy works of Samancor at Meyerton, South Africa in order to increase the effectiveness with which energy is utilized.

Jan 1, 2004

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

By S. Heukelman

Zinc or, a zinc refinery in South Africa, uses oxygen enrichment of up to 26% O2 in its fluidizing air to increase concentrate-throughput in its fluidized bed roasters. The aim of the study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining concentrate throughput rates and calcine quality. A laboratory scale fluidized roaster was used to determine the strength and oxidation kinetics of suitable micro-pellets. The strength of the pellets was determined by the extent of attrition during roasting. It was found that micro-pelletization decreases the fines in the feed to the roasters; the ?500 µm fraction decreased from 87% to 10%. The micro-pelletized particles do break down during roasting, which increases the -500 µm fraction to 31%. The general morphologies of the roasted particles are similar to those found by previous workers. Micro-pelletized concentrate particles require more time than non-pelletized concentrate particles to oxidize in the roasting step, although this is less than the mean residence time of the Zincor roasters. Roasting micro-pellets in O2-enriched fluidizing air increased the reaction rate.

Jan 1, 2011

By N. Gatelier, T. You, J. C. Kandel

ABSTRACT: Underground hydrocarbons storage is a very specific domain for the designer. He is usually free to adjust the section, shape and layout to cope with the geological and geotechnical conditions. This paper presents a panorama of the geotechnical design of mined underground storage caverns, then lists a number of uncommon features encountered in a storage excavated in Sydney, Australia, the Elgas LPG project that had to face major non-isotropic conditions with numerous local variations, impacting on the achievement of the design profiles. Changes in geotechnical design methodology and practice are examined through this project, now in operation, which will have lasted altogether almost ten years. KEY WORDS: underground storage, geotechnical engineering, stability, methodology, design. ZUSAMMENFASSUNG: Die untertaegige Speicherung von Kohlenwasserstoffen unterliegt in der Planung sehr spezifischen Bedingungen. Der planende Ingenieur hat bei der Dimensionierung und Formgebung der Speicherhohlraeume gewisse Freiheiten, muss jedoch vorgefundene geologische und geotechnische Bedingungen beruecksichtigen. Der vorliegende Beitrag gibt zunaechst einen allgemeinen Ueberblick ueber die geotechnische Planung von bergmaennisch aufgefahrenen Speicherhhohlraeumen. Darueber hinaus werden Besonderheiten betrachtet, mit denen das Elgas LPG-Speicherprojekt in einer bergmaennisch aufgefahrenen Kaverne in Sydney, Australien konfrontiert war. Hierbei ging es um die Beruecksichtigung anisotroper Bedingungen mit zusaetzlichen Heterogenitaeten im Gestein und den daraus erwachsenden Schwierigkeiten, die geplante Hohlraumform zu verwirklichen. Ueber einen Zeitraum von fast 10 Jahren, in denen das jetzt in Betrieb befindliche Projekt unterschiedliche Betriebsphasen durchlaufen hat, wurden verschiedene geotechnische Entwurfsverfahren auf ihre Anwendbarkeit geprueft. SCHLUESSELWOERTER: Untergrundspeicherung, Geotechnik, Stabilitaet, Entwurfsverfahren, Planung. RESUME : Le stockage souterrain d’hydrocarbures est un domaine très spécifique pour le concepteur, car celui-ci dispose d'une large liberté pour adapter les sections, les formes et les implantations aux conditions géologiques et géotechniques de l’environnement choisi. Après un panorama de la conception géotechnique des stockages souterrains d’hydrocarbures par la méthode dite des cavités minées, l’accent sera mis sur un certain nombre de particularités rencontrées lors du projet de stockage de GPL de Elgas à Sydney en Australie, creusé dans de très fortes conditions d’anisotropie du massif rocheux, avec de nombreuses variations locales et toutes les implications que cela peut avoir sur le maintien des formes. L’évolution des approches méthodologiques géotechniques durant la dizaine d'années de développement de ce projet depuis les premières études jusqu'à l'exploitation actuelle est également présentée. MOTS-CLEFS : stockage souterrain, géotechnique, stabilité, méthode, conception.

Jan 1, 2003

An extensive laboratory grinding study was carried out on a magnetite ore in order to assess the grinding behaviour of magnetic concentrate and tail from low intensity magnetic separation (LIMS).The test work involved Bond ball mill testing, rod milling, low intensity magnetic separation (LIMS), and batch ball milling down to product sizes of around P80~25 microns. A total of 18 Bond tests and over 150 batch grinding tests and sieve sizing were carried out. Throughout the grinding tests, power draw was continuously monitored. The relationship between the grinding energy and product size was analysed using the conventional energy-size concepts. It was found that the Rittinger equation fits the experimental data well. However, Bond?s equation does not fit the experimental data well, and therefore a modified Bond equation was developed. Differences in grinding properties between the magnetic and non-magnetic component were analysed and compared to the bulk ore. It was found that grinding properties differ significantly and therefore separate grinding test work may be required for each grinding step in the magnetite ore beneficiation flowsheet. Keywords: grinding, iron ores, particle size, modelling.

Jan 1, 2010

By R. Drummond

The fourth Teetered Bed Separator (TBS) has just been installed in Australia, and trials have been run in many sites. There is a growing recognition of the potential advantages of using TBS technology to treat coal in the ?3+0.25 mm size range, at cut points below 1.60. From these activities, there has been a substantial growth in knowledge with respect to application engineering and operational functions. The paper briefly describes the installations, including flowsheets, and so provides a background to the potential deployment of TBS technology. There are a large number of potential applications for TBS technology, including treatment of fine ROM coal in new plants, or in upgrade situations for re-processing of spiral product, or scavenging coal from coarse tailings. As well, cost effective capacity upgrades are possible by using TBS units for treating the sands size fraction. Issues arising from Australian TBS installations and application engineering are also discussed.

Jan 1, 2002

By David Brown, Dirk van Dyk

Horizontal rotating mills are being used all over the world associated with different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions with are not always fully understood. Failures are therefore experienced, over time in the industry, which can therefore not always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyze these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyze the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating conditions are better understood, and the effect on the fatigue life of the mill gearing components, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2007

By K. Goshtasbi

In this paper a genetic algorithm is used in a heavily jointed rock mass in order to investigate the critical circular slip surface and modification of slope surface. This method was applied to the southern wall of the 6th Golbini Jajarm bauxite mine. The mine is the largest bauxite deposit in Iran, located to the northeast of the town of Jajarm in the Khorasan province. Estimated reserve of bauxite in this deposit is about 160 million tonnes. Field and laboratory investigations were conducted in order to determine rock mass behaviour. A genetic algorithm code that uses the Simplified Bishop method as an objective function was developed for findingt he safety factor of circular slip surfaces. Sensitivity analysis was applied to determine the optimum values of the genetic algorithm variables, such as population size, selection method, crossover and mutation rates. After finding the critical circular slip surface, slope modification is carried out by removing unstable sections from marked critical slip surfaces, and this process is repeated until the last unsafe section is removed. Based on this code, modification occurred during 7 steps, by reaching a safety factor of 1.3 in the last step. Finally, the modified slope angle of the southern wall of the 6th Golbini Jajarm bauxite mine was determined to be 48.44 degrees. Keywords: Genetic algorithm, slope modification, circular slips surface, 6th Golbini Jajarm bauxite mine .

Jan 1, 2008

By M. K. Sichone

Anglo Platinum?s Waterval smelting complex based in South Africa operates the Anglo Converting Process (ACP) that produces SO2 offgas. This SO2 offgas is treated in a double-contact, double-absorption acid plant allowing for conversion efficiencies higher than 99.90 %. The catalytic converter used in the acid plant to convert the SO2 to SO3 is a 4-bed reactor loaded with a combination of cesium-promoted and conventional vanadium pentoxide catalysts. In June 2008 there was a shutdown, in which one of the main activities was to screen the catalyst. Before this shutdown, the operator would control the converter pass temperatures manually, via the SCADA, especially during plant start-ups after which some of the automatic temperature controllers were used. After the shutdown, the control philosophy was revisited and all temperature controllers were put on auto mode during plant start up. Furthermore the set points of the pass inlet temperatures were reduced to maximize conversion in the first two passes. The result has been a reduction of SO2 emissions, from a daily average of 50 ? 70 ppm to as low as 20 ppm for similar sulphur dioxide and oxygen concentrations. Further work has been done to maintain high bed temperatures in the third and fourth passes at low SO2 strengths by splitting the gas stream between pass 1 and 2 thus increasing the SO2 content in the gas to pass 2. This increases the temperature of the gas exiting the second pass, which results in higher temperatures in passes 3 and 4. Comparison of the converter performance prior to and after the changes is made. The benefits of partially bypassing the first pass to increase the SO2 content in the gas to the second pass are shown. Conclusions and scope for further work have been drawn from the comparisons.

Jan 1, 2009

Milling circuits are known to be difficult to control. In order to address these difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written using Microsoft Visual C++ and used to design and test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimizing algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. Control was further improved by combining feedback and feed forward control and by using quadratic programming in the MPC algorithm. The movement of the manipulated variables was reduced by using a novel technique that allows the controlled variable to vary within a specified region around the set point. An optimiser controller was also successfully implemented to control the circuit at its maximum throughput.

Jan 1, 2000

By A. Pellegrino, F. Collin, C. Guiducci, R. Charlier

A numerical approach for modeling coupled Hydro-Mechanical fracture behavior in 2D is presented in this paper. This approach accounts for the strong dependence of the flow characteristics on fracture apertures and offers an anisotropic description of the flow propagation in the fracture. An interface finite element and a constitutive model are developed . In order to validate the applicability of the model to general geomechanic problems, 2D simulations were performed. Results show the good application of the mathematical model and the fundamental hydraulic role played by the fractures. In diesem Beitrag wird ein Stoffgesetz vorgeschlagen um hydromechanisches Kluftverhalten numerisch zu Modellieren. Dieser Vorgang nimmt die starke Abhängigkeit der Fliesseigenschaften von der Kluftöffnung mit in Anbetracht. Ein Interfaceelement und ein Stoffgesetz wurden entwickelt. Zum validieren der Anwendbarkeit dieses Modells wurden 2D Simulationen durchgeführt. Ergebnisse haben gezeigt dass das mathematische Model anwendbar ist und dass Klüfte eine fundamentale hydraulische Rolle spielen. Une approche numérique pour la modélisation du comportement couplé hydro-mécanique des fractures en 2D est présentée dans ce papier. Cette approche prend en compte la forte dépendance des caractéristiques du flux de fluide sur les ouvertures des fractures et présente une description anisotrope de la propagation du flux dans la fracture. Un élément fini d'interface et un modèle constitutif sont développés. Dans le but de valider l'applicabilité du modèle à des problèmes généraux de géomécanique, des simulations 2D ont été réalisées. Les résultats montrent la bonne application du modèle mathématique et le rôle hydraulique fondamental joué par les fractures.

Jan 1, 2003

By B. Genc

Safety in South African mines is a subject of significant interest, since many mining companies are experiencing production deficits due to safety-related stoppages. In this paper, safety data from the South African platinum mining sector is analysed for the period 2006 to 2010. The data was obtained from company annual reports as well as the Department of Mineral Resources, and analysis in the study is limited to injury and fatality data only. The overall safety performances of companies in the sector are compared, and opportunities for benchmarking and recognising potential sources of best practice amongst platinum miners are identified. Improving safety usually incurs a cost, and mining companies are particularly conscious of the importance of controlling costs. However, cost considerations often deal only with direct costs, and it has been shown that indirect costs are usually far more significant. Therefore, a greater safety spend will usually result in the creation of value for the mine since it will reduce the indirect costs associated with accidents. The results of some recent research in this area are presented. In this light, where available, the financial performances of mining companies in the sector, obtained from published annual results, are included in the benchmarking exercise to determine whether there is any correlation with safety performance.

Jan 1, 2012

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By R. Trammell, O. Eterigho-Ikelegbe, S. O. Bada

In response to the enormous amounts of coal discard generated during coal mining and preparation, the development of an efficient and sustainable strategic use of this resource is essential. Furthermore, the rising urban population over the next decades is confronted with the depletion of quality raw materials for building components. To this end, this study reports new information on the morphology, water absorption, and flexural strength properties of ceramic composites produced from three different coal discards and polysiloxane pre-ceramic polymer (PCP) resin. In addition, test results relating to the continuous operating temperature, chemical resistance, and efflorescence potential of the composites are presented. The results show that the water absorption and flexural strength of the coal composites, up to 1.94% and 36.46 MPa respectively, exceed the requirements for ceramic and clay roof tiles. The continuous operating temperature of composites is found to be more thermally stable than conventional roofing tiles (concrete and ceramic) between ambient temperature and 600°C. In addition, the excellent chemical resistance of the composites (94.43%−99.98%) compared to conventional roofing tiles (67.82%−99.97%) eliminates the need for additional external coatings. The interesting results documented so far suggest that this technique could be used to produce low-temperature application building products such as bricks, panels, roofing tiles, etc. This new recycling technique offers an excellent opportunity to eliminate enormous volumes of coal discard and to advance the circular economy in the coal industry.

Aug 2, 2022

By H. Tveit, E. H. Myrhaug, J. K. Tuset

Silicon metal as a commodity material is produced by carbothermic reduction of quartz in electric submerged arc furnaces, where CO2 forms as a by-product. Since 1997 the Norwegian Ferroalloy Producers Association have been engaged in research programmes aiming for reduced CO2-emissions associated with fossil carbon in their processes. One important issue has been to study how charcoal and wood chips perform compared to coal and coke in the silicon process. The ability of the carbon-rich reduction materials to react with SiO-gas is commonly assumed to be of large importance to the performance of the process. Based on laboratory experiments with different carbon materials, combined with estimation of parameters in a mathematical model of the reaction between carbon and SiO-gas, a foundation for a theoretical study of the performance of the carbon materials in a silicon furnace is established.

Jan 1, 2004

By J. O. Claassen

"A study conducted at 22 operating mines in the southern African region indicated that each mine employs about five management and improvement methods with roots in the manufacturing industry. All respondents reported the implementation of cost-saving initiatives, whereas 80% of the mines are affected by restructuring. TQM, Six Sigma, BPM, and TOC were found to be the most prevalent manufacturing management and improvement methods used. A mechanistic vs systemic evaluation of the suitability of these methods to bring about positive change in the industry suggested that complex, ever-changing mining systems are better served by a systemic flow-based approach, which is embedded in methods such as TOC, JIT, TPS, and Lean Production. These methods, however, lack industry presence, possibly because they do not effectively deal with the unique challenges associated with the mining environment. It is argued that successful mining business management and improvement depends on management’s ability to deal effectively with mining industry-specific requirements, the integration of the geologymining- plant system, and the implementation of systemic flow-based principles in all aspects of mining. IntroductionThe study aims to explore the use of manufacturing management and improvement methodologies in the southern African mining industry. Considering the unique challenges associated with mining operations, attention is given to the applicability of the most commonly used manufacturing methodologies in the tactical, operational, and strategic environments. The article endeavours to stimulate more research and debate in an unexplored field of study."

Jan 1, 2016

By B. Genc, P. Malepfane

This study proposes a new approach to reduce the environmental impact during surface mining by improving environmental factors through the incorporation of carbon footprint into strategic mine planning. Two key variables were analysed by contrasting and comparing the baseline and optimised models generated. These variables include net present value, which helps determine the financial feasibility of the mining models and their carbon emissions. The variables were analysed by using linear regression, Spearman’s correlation, a P-value hypothesis, and an exponential decay test. Results show that at Mine A the projected net present value was 62% higher than when running a baseline model. Furthermore, the net present value from the baseline model portrayed a high rate of decay at 0.667 versus 0.118 from the optimised model. This indicates the baseline model’s sensitivity to long-term project timelines and fluctuating markets. The optimised method presents an opportunity to manage emissions during the high operational costs phases. It is represented by a 31% improvement in carbon emissions during the periods of high operational costs, whilst maintaining a positive net present value when compared with the baseline model. It was shown that the optimised model presents a better chance of achieving financial feasibility and balancing environmental impact, thereby ensuring that Mine A can align with the environmental aspect of economic, social, and governance principles through lowering the carbon footprint resulting from its hauling operations.

Jan 30, 2026