Search Documents

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By Jochen Petersen, Thandazile Moyo

"The oxidative leaching of chalcopyrite in ammoniacal solutions has been evaluated using electro-analytical techniques. The anodic dissolution process has been established to be a seven-electron transfer process under nitrogen in ammonia–ammonium sulphate solutions and ammonia–ammonium carbonate solutions. The number of electrons transferred in the carbonate and sulphate salts suggests that the sulphur is oxidised to a thiosulphate intermediate and the copper and iron released as Cu+ and Fe2+. The Cu+ and Fe2+ is subsequently oxidised in solution in non-Faradaic reactions. The deportment of Fe2+ and S2O32- is affected by choice of the ammonium salt used in the leaching process. In the perchlorate salt, only five electrons are transferred, however observations made on the mineral surface after leaching do not support the formation of elemental sulphur. Scanning electron microscopy and energy-dispersive spectroscopy analysis of the mineral surface suggest presence of an iron–sulphur surface layer completely free of copper under the ammonia–ammonium sulphate conditions, an iron-rich surface layer under ammonia–ammonium perchlorate solutions and absence of surface layer build up under ammonia–ammonium carbonate solutions. INTRODUCTION Hydrometallurgical processes for copper extraction provide a viable route to recover the metal from mixed and low-grade ores, as well as overcome the environmental challenges faced by the traditional pyrometallurgical processes. Chalcopyrite is not only the most abundant of the copper sulphides, but also the most stable, making it recalcitrant to hydrometallurgical processes. Hence, hydrometallurgical processing of chalcopyrite continues to be an attractive area of research due to the vaguely understood surface chemistry of the mineral in different aqueous media. Different approaches to hydrometallurgical treatment of chalcopyrite can be carried out. These include thermal treatment prior to leaching, direct leaching and direct electrochemical leaching (Venkatachalam, 1991). Direct leaching of chalcopyrite can be carried out in various solution systems, as reviewed by Roman and Benner (1973) and Venkatachalam (1991). Ammoniacal solutions are attractive and effective lixiviants that form stable amine complexes with some base-metal cations while rejecting iron. Leaching of chalcopyrite in ammoniacal solutions in the presence of an oxidant is possible due to the stabilisation of copper(I) and copper (II) by ammonia at elevated pH levels. In oxygenated ammonia solutions, it has been suggested that chalcopyrite dissolves according to Equation 1 (Beckstead & Miller, 1977a):"

Jan 1, 2015

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By F. Rwere, A. Masasire, P. Dzomba, M. Mupa

Accurate determination of platinum group metals (PGMs) and gold (Au) has always proven to be a difficult task, due to their low concentrations in platiniferous ores. The most common preconcentration technique used in analysis of these metals is fire assay with a flux containing nickel or lead. This technique can be improved by using co-collectors. Here we hypothesise that Fe, Co, and Cu can be used as co-collectors to enhance separation and preconcentration of PMGs and gold by fire assay. To test this hypothesis, geological exploration samples from Siyanda Union Mine (Northam, South Africa) were analysed by an inductively coupled plasma-optical emission spectrometer (ICP-OES) for PGMs (Pt, Pd, and Rh) and Au. A control sample (certified reference material AMIS 0426) was also analysed by the same technique. The PGM and Au recoveries from the control sample ranged from 83% to 105% for all three co-collectors, with relative standard deviations less than 10% for the control sample and 7% for the geological samples. The PGM and Au recoveries by Fe and Co co-collectors were modestly higher than that of the Cu-collector. These results indicate that Fe and Co are better co-collectors than Cu, presumably due to the loss of analyte when using Cu. Taken together, Fe and Co co-collectors can be viable alternatives for analysis of PGMs and gold using the fire assay method.

Jan 2, 2022

By P J. Grobler

The current commodity boom is depleting the ore bodies at a rate not seen in the past. As the existing ore bodies get depleted, only the more inferior bodies are left for exploitation. This places an emphasis on beneficiation to upgrade the lower grade ore to high-grade feedstock for downstream processes. This paper discusses the role of dense medium separation in this quest for high-grade feedstock for the future. It covers the production and utilization of ferrosilicon and gives a future perspective of the technology. It concludes about the way ahead and the challenges facing the processing fraternity and mining industry.

Jan 1, 2006

By P. den Hoed, R. I. Rambiyana

"Four sulphide minerals - pyrite (FeS2), pyrrhotite (Fe1-xS), pentlandite ([Ni,Fe]9S8), and chalcopyrite (CuFeS2) - contain the base metals and most of the iron in concentrates of platinum group metals (PGMs). In the pyrometallurgical processing of PGM concentrates these sulphides form a matte during smelting, and iron and sulphur are removed from the matte during the converting process. This paper discusses the roasting of Merensky concentrate in air before smelting, with the purpose of reducing the matte load to the converter.Roasting tests were conducted in a bench-scale rotary kiln at temperatures from 350°C to 700°C. The concentrate tested contained 17.4% sulphur and consisted of 23% pyrrhotite, 16% pentlandite, 11% chalcopyrite, and 2% pyrite. The particles were fine (d50 = 22 µm), and all the sulphide particles were liberated. Roasting in air at 550°C and 650°C for 20 minutes removed respectively 60% and 70% of the sulphur. The iron in the sulphides was oxidized to Fe3O4 (magnetite) at temperatures below 500°C and to Fe2O3 (haematite) at temperatures above 550°C. At 700°C the bed sintered and copper oxides formed. At temperatures below 450°C oxidation was incomplete: pyrrhotite remained and only 30% of the sulphur was removed. Smelting tests were conducted to assess matte fall and the deportment of copper and nickel to matte. It was evident that roasting resulted in lower matte falls (a drop of approximately 60%) compared with matte falls from unroasted concentrate. The iron and sulphur levels in the matte were reduced to below 3.5% and 22% respectively.This paper also briefly describes the mechanisms by which pyrrhotite, chalcopyrite, and pentlandite are oxidized during roasting. For chalcopyrite, the mechanism proceeds through an intermediate solid solution phase, which extends from Cu1.02Fe1.04S2 to Cu2.04Fe0.72S2 to a copper-rich solid solution of bornite (Cu4Fe1.4S4-Cu2S). The oxidation of pentlandite proceeds through a monosulphide solid solution (Ni0.39Fe0.53S-Ni0.74Fe0.15S) to a solid solution of heazlewoodite ([Ni,Fe]3}xS2). These mechanisms are explored in relation to chemical thermodynamics and microstructures."

Jan 1, 2015

By J. P. Josien, J. F. Noirel, F. Lahaie, P. Bigarre, M. Al Heib

ABSTRACT: In June 2001, a fatal rockburst affected a longwall face in the Houillères du Bassin de Lorraine (HBL), France. Subsequently, a large operation of in situ stress measurements by overcoring was carried out with two main objectives: providing input data for the back analysis of the dynamic event and characterising the stress field in the next panels to be mined for identifying other potential high-risk zones. This paper makes a synthesis of the results of the overcoring tests performed and discusses those results in connection with the mining context, numerical model predictions, laboratory rock test results and microseismic activity. KEY WORDS: Mine, rockburst, stress, overcoring, measurement. ZUSAMMENFASSUNG: Im Juni 2001 hat ein Bergschlag eine Kohlengrube des Houillères du Bassin de Lorraine (HBL, Lothringen, Frankreich) schwer beschädigt. Nach diesem Unfall sind Spannungsmessugen durch Überborung durchegeführt worden, mit zwei Hauptziele : 1/ Daten zu liefern für die Retro-analyse des dynamischen Gebirgsschlag und 2/ die Spannungen in den zukünftigen Ausbauen so gut wie möglich zu charakterisieren, um eventuele andere Risikozonen festzustellen. Dieser Artikel stellt eine Synthese der erzielten Ergebnisse vor. Er diskutiert diese Ergebnisse in Verbindung mit dem gesamten Kohlengruben Zusammenhang, mit den Ergebnissen von numerischen Modellierungen, mit der Labor-Charakterisierung und mit der microsismische Überwachung. SCHLÜSSEL-WÖRTER: Kohlengruben, Bergschlag, Spannung, Überborung, Messung. RESUME: En Juin 2001, un coup de terrain a gravement affecté une longue taille aux Houillères du Bassin de Lorraine (HBL) en France. A la suite de cet accident, une importante campagne de mesures de contraintes par surcarottage a été réalisée, avec deux objectifs majeurs : fournir des données d’entrée permettant la rétroanalyse du phénomène dynamique et caractériser au mieux le champ de contraintes dans les futurs panneaux exploités afin de détecter d’éventuelles autres zones à risque. Cet article présente une synthèse des résultats obtenus, et discute ces résultats en liaison avec le contexte d’exploitation, les résultats de modélisation numérique, de caractérisation en laboratoire et de surveillance microsismique. MOTS CLES: Mine, coup de terrain, contrainte, surcarottage, mesure.

Jan 1, 2003

By V. Labiouse, M. Jaboyedoff

GIS documents are of great interest for a quick and low-cost determination of areas endangered by rockfalls. They allow (i) the detection of potential instabilities from steep slopes and cliff areas, and (ii) the preliminary estimation of potential run-out areas by means of a so-called cone method. After the presentation of the tools used to compute these areas, the paper focuses on two methods developed for a preliminary hazard mapping, one at regional scale and the other at local scale. Mittels GIS-Dokumenten können von Steinschlag bedrohte Gebiete schnell und kostengünstig ermittelt werden. Die sogenannte Kegelmethode erlaubt die Erkennung potentiell instabiler Zonen von Steilhängen und Felswänden sowie eine erste Einschätzung der möglichen Reichweiten. Nach der Vorstellung der zur Berechnung der bedrohten Gebiete benötigten Hilfsmittel stellt der Artikel zwei Methoden zur vorläufigen Gefahrenkartierung in lokalem und regionalem Maßstab vor. Les SIG sont très intéressants pour une détermination rapide et peu onéreuse des zones affectées par des chutes de blocs. Ils permettent une détection des zones potentiellement instables et une estimation sommaire des zones de propagation des blocs par une méthode dite des cônes. Après la description des outils utilisés pour définir ces zones, l’article expose deux méthodologies élaborées pour un zonage préliminaire du danger, l’une à l’échelle régionale et l’autre à l’échelle locale.

Jan 1, 2003

By T. Ito, N. Tokashiki, H. A. Bilgin, Ö. Aydan, T. Akagi

This study is concerned with the electric potential induced by deformation, fracturing and sliding of non-piezoelectric geomaterials. In experiments, the acoustic emissions together with electric potential measurements were also measured in order to see how the so-called seismic electric signals are associated with new fracture occurrence and propagation and sliding in case of existing discontinuities. The outcomes of this experimental study may explain why such electric potential variations may occur during the fracturing and sliding of non-piezoelectric geomaterials. On the basis of these outcomes, their possible implications in geo-engineering and geo-science are discussed. Ce travail concerne 1e potentiel électrique produit par la déformation, 1a fracture ou le glissement du matériel géologique non-piézoélectrique. Aux expérimentations, on a mesuré 1es émissions acoustiques avec le potentiel électrique afin de constater la relation entre les phénomènes de glissement ou de formation et de propagation de nouvelles fractures le long des discontinuités existantes. Les résultats de ce travail expérimental expliquent pourquoi de telles variations de potentiel electrique se produisent durant le glissement ou la fracture du matériel non-piézoélectrique. Sur la base de ces résultats, on a discuté de leurs éventuelles implications dans les domaines de 1a géologie et de 1a géo-ingénierie. Diese Studie befasst sich mit dem elektrischen Potential das durch die Deformation, Bruchbildung und Gleiten von nicht-piezoelektrischen Geomaterialien induziert wird. In Experimenten wurden die akustischen Emissionen zusammen mit elektrischen Potentialmessungen gemessen, um zu sehen, wie die so genannten seismischen elektrischen Signale mit neuer Bruchbildung und Ausbreitung sowie Gleiten im Falle von vorhandenen Diskontinuitäten verbunden sind. Die Ergebnisse dieser experimentellen Untersuchungen könnten erklären warum elektrische Potential Schwankungen während der Bruchbildung und dem Gleiten von nicht-piezoelektrischen Geomaterialien entstehen. Auf der Basis dieser Ergebnisse, wurden ihre möglichen Implikationen in Geoingenieurwissenschaften behandelt.

Jan 1, 2003

The optimum cut-off grade policy maximizes the net present value (NPV) of an open pit mining operation subject to the mining, processing, and refining capacity constraints. The traditional approaches to cut-off grade determination ignore the escalation of the economic parameters such as metal price and operating costs during life of an operation, and consequently lead to unrealistically higher values of the objective function. Further, the NPV of a mining operation declines due to the depletion of the available reserves, causing a decline in the optimum cut-off grade, i.e. higher cut-off grades in the early years of an operation and lower cut-off grades during the later years. Hence, low grade material mined in the earlier years may be stockpiled for processing during later years to offset the effect of escalating economic parameters on NPV. This paper demonstrates the combined impact of introducing economic parameters, escalation and stockpiling options into the cut-off grade optimization model. The model promises an enhancement in NPV as illustrated in a case study incorporating practical aspects of an open pit mining operation.

Jan 1, 2011

By M. Hopf, E. Rossouw

Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able to consistently identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed). Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa.

Jan 1, 2006

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By J. P. Gous, J. J. Sutherland

"Transalloys is a silicomanganese (SiMn) producer located in South Africa, and uses only local manganese ores to produce SiMn alloy. The plant operates five open submerged arc furnaces (SAFs) with an annual capacity of 180 000 t of saleable SiMn.Maintaining tap-holes is critical for effective furnace operation, allowing proper drainage of the furnace with minimal operator interference. Using a claygun and drill arrangement installed at each furnace, tapping occurs every four hours. Tap-holes are maintained through mickey replacement and brick repairs. Three furnaces have SiC tap-holes and two have graphite tap-holes.This paper gives a review of SAF operation, furnace and tap-hole design, daily tapping operation, and maintenance practices for repairing tap-holes.IntroductionDefining tap-hole life cycle, Steenkamp et al., (2016) highlighted four main steps: installation during furnace relines, day-to-day operations, tap-hole maintenance, and tap-hole repair. The authors argued that the design of the tap-hole area should allow for all four stages in the tap-hole life-cycle. Design principles for each stage were presented using silicomanganese (SiMn) production as a case study. Here we present a further analysis of the case study by providing practical examples of how the tap-hole life-cycle is managed at Transalloys during the design, operation, and maintenance of submerged arc furnaces (SAFs) applied in the production of SiMn.BackgroundTransalloys is the largest producer of SiMn in Africa. Its smelter complex is based outside the town of eMalahleni, in the Mpumalanga Province of South Africa. Transalloys was commissioned in the mid- 1960s as a high- and low-carbon ferrochromium plant based on the Perrin process. In 1967 the plant was converted to SiMn production because of constraints in the ferrochrome market (Basson, Curr, and Gericke, 2007; Bezemer, 1995). Today, the installed production capacity is 180 000 t of SiMn annually. Plant operations consists of five SAFs (see ratings in Table I), operating 24 hours a day, 365 days a year (including maintenance), involving 280 permanent employees, with up to 120 contract employees on site at any given time."

Jun 1, 2019

By C. Swart

Automation technologies are increasingly adopted in different mines world-wide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHDs at Noranda?s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHDs and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda?s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Jan 1, 2002

By J. L. Human, N. Fernandes

The rockfall hazard is the major contributing agency to fatal accidents in South African platinum mining operations. The majority of these accidents occur in close proximity to the working stope face. The collapse of fractured or blocky ground between individual temporary support units or the closest permanent support line to the stope face has not yet been adequately addressed. A large-scale stope support system testing facility funded by the Safety in Mines Research Advisory Committee (SIMRAC), has been designed and constructed to test support systems and stimulate innovative thinking by mining personnel, support manufacturers and suppliers by providing a facility where the interaction of stope support systems, a rigid stope face and a discontinuous hangingwall beam can be observed during quasi-static and dynamic conditions. Tests have been carried out on various types of stope support systems, focusing on the temporary support systems used in the immediate stope face area. The interlinking of the temporary support units with mesh or safety netting has been explored in the prevention of falls of ground between support units during gravity driven falls of ground. These tests illustrate the facility?s ability to be used to stimulate innovative thinking and provide a testing ground for the development of temporary support systems in order to reduce the risk off all of ground injury to mining personnel at the stope face.

Jan 1, 2004

Water represents 80?85% of the volume of mineral pulp processed in flotation circuits. Imperatives for a more detailed focus on circuit water quality and its control have come from increasing requirements to use relatively impure primary water supplies (e.g. high salinity, treated sewage) and high proportions of recycle from tailings dams, thickener overflows, dewatered and filter products. An integrated methodology for examining process water quality and its effect on minerals separation has been developed coupled with minerals surface chemistry across the complete processing circuit. Unrecognised factors, including varying proportions of water streams (daily or hourly), colloidal precipitation, highly variable pH and Eh, reaction and dissolution of minerals, minerals surface layer coatings, residual reagents and their reaction products, and microbiological activity have been studied in eight mineral processing circuits. The methodology combines: solution survey and modelling; microbiological surveys; minerals surface analysis and modelling; and process response. It has been possible to match the predicted (model) pulp chemistry with that measured from surveys of the solution and mineral surfaces. Treatment methods have included: monitored and balanced stream combinations; organic species removal; flocculation and aggregation; induced precipitation; dissolved air flotation; ageing (oxidation, UV exposure); and chemical surface conditioning of minerals. Some specific achievements from the methodology applied in plant and laboratory testing, with examples from case studies, will be described.

Jan 1, 2001

By T. A. Muhlare

The use of electrolyte additives to smoothen cathode deposits during copper deposition is practised worldwide. These additives absorb on the cathode surface and take part in the electrochemical crystallization process. However, these additives also affect the quality of the cathodes when they are inadequately controlled. Electrolyte additives used by Palabora are glue, thiourea, Avitone and chloride. Their effects were determined on cathode quality, the size of the current density region that gives the desired compact morphology, and current efficiency. This was done in a small-scale cell. Small cells have different hydrodynamics from industrial-scale cells, which makes it difficult to simulate the operation of industrial cells in a laboratory. The approach used here was to use a rotating cylinder cathode to attain controlled hydrodynamics. The rotation speed was chosen to give a diffusion layer thickness that is similar to that of an industrial-scale cell. It was shown that even fairly small changes in the additive levels can significantly affect the cathode morphology, and the current density range over which this morphology can be obtained. Keywords Copper, electrorefining, glue, thiourea, avitone and chloride.

Jan 1, 2011

By I. K. Craig, F. R. Camisani-Calzolari

Defects which occur at the surface of a continuously cast slab impede the throughput of final product, because an extra stage in the process is required to grind the defects away before further processing can take place. Defect prediction and the minimization of the occurrence of defects is required. The use of two models to define the defect propagation is explained. Both models are derived using system identification techniques such as auto-regression with exogenous input(ARX). One model is used to determine the effect of manipulated variables such as casting speed and measured disturbances such as mould level on temperatures within the mould. The other isused to determine or indicate the effect of the mould temperatures on the occurrence of defects such as transversal cracks. The latter model can be used to predict when the defects will occur and the former can be used to control the occurrence of the defects. Keywords: continuous casting, surface defect, control system, predictor, system identification, ARX

Jan 1, 2003

By Y. Sagawa

The Hishikari Gold Mine consists of epithermal vein type Au-Ag deposits, each of which has several veins standing almost in parallel each other and inclining 70 to 90 degrees. The veins have 1 to 3m widths and are extracted mainly by drifting and bench stoping with waste rock fill. The Hishikari has tried to optimise the stope dimensions by the Potvin’s Stability Graph Method, which is well known as an easy and effective tool to design appropriate stope dimensions. The method, however, has some limitations of application due to its simplicity so that it has been used only in limited cases. The authors developed a new numerical approach, based on 2D FEM solu-tion for the stability analysis. As a result, it has been possible to solve the Hishikari situation. The authors also introduce the concept of the design approach and compare the results obtained by us-ing the approach with the database of the Stability Graph Method for validation. La mine d’or Hishikari se compose de gisements d'Au-AG avec des types de filons épither-maux dont chacun a plusieurs veines qui sont presque parallèle les unes par rapport aux autres et sont inclinées de 70 à 90 degrés. Les veines ont de 1 à 3 m de largueur et elles sont principalement extraites en creusant et en abattant des bancs de roches encaissantes. Hishikari a essayé d’optimiser les dimensions du chantier d’exploitation avec la méthode de graphique de stabilité de Potvin, bien connue comme un outil facile et efficace pour avoir des dimensions de chantier d’exploitation appropriées. Toutefois, la méthode a certaines limites d’application dues à sa sim-plicité de sorte qu’elle a été utilisée seulement dans des cas limités. Les auteurs ont développé une nouvelle approche numérique, basée sur la solution 2D FEM, pour l’analyse de stabilité. Par conséquent, il a été possible d'expliquer la situation de Hishikari. Les auteurs présentent le concept de l'approche et ils comparent les résultats donnés en l'employant avec la base de données de la méthode de graphique de stabilité pour la validation. Die Hishikari-Goldmine besteht aus Au-Ag-Ablagerungen mit epithermalen Adern, die jeweils mehrere Adern aufweisen, die mit einer Neigung zwischen 70 und 90 Grad nahezu parallel zueinander verlaufen. Die Adern haben eine Breite von 1 bis 3 Metern und werden überwiegend durch Vortrieb von Stollen und Bergversatz abgebaut. Hishikari hat versucht, die Abmessungen des Abbauorts durch das Potvins Stabilitätskurvenverfahren zu optimieren, das als einfaches und effizientes Mittel für die Erzielung angemessener Abmessungen des Abbauorts bekannt ist. Das Verfahren weist jedoch aufgrund seiner Einfachheit einige Anwendungsbeschränkungen auf, so dass es nur in einigen Fällen benutzt worden ist. Vor diesem Hintergrund haben die Autoren einen neuen numerischen Ansatz entwickelt, der hinsichtlich der Stabilitätsanalyse auf der 2D-FEM-Lösung beruht. Dadurch wurde es möglich, das Problem von Hishikari zu lösen. In diesem Dokument stellen die Autoren die Grundlagen des Ansatzes vor und vergleichen die erzielten Resultate durch Benutzung der Datenbank des Stabilitätskurvenverfahrens zur Validierung.

Jan 1, 2003

Common practice in mineral resource estimation consists of partitioning the orebody into several domains defined by grade intervals, prior to the geostatistical modelling and estimation/simulation at unsampled locations. This paper shows the pitfalls of grade domaining through a case study in which we compare the performance of several estimation schemes and demonstrate that the use of domains defined by grade cut-offs implies a deterioration of the resource estimates, mainly in what refers to precision and conditional bias. Then, several conceptual limitations of the grade domaining approach are stressed, in particular the fact that it does not account for the spatial dependency between adjacent domains and for the uncertainty in the domain boundaries. Also, this approach is shown to be sensitive to the cut-offs that define the domains, to provoke artifacts in the kriging maps, histograms and scatter grams between true and estimated grades, and to lower the kriging variance, a feature that may impact the mineral resource classification. An alternative approach is finally proposed to overcome these limitations, based on a stochastic modelling of the grade domains and a co-kriging of the grades using information from all the domains. Keywords: geostatistics, kriging, conditional bias, geological control, grade zoning.

Jan 1, 2005