Search Documents

Measure dangerously high concentrations (20 to 500 g/m3) of flammable, airborne dust. Approach Development of high concentration dust monitor (HCDM) which will measure mass concentrations of air borne dust by the principle of beta-ray attenuation. How It Works The HCDM is a battery powered, portable instrument that weighs 10.5 kg. It is capable of making continual (10 sec. time resolution) measurements of high concentrations of airborne dust and can record up to 8 hours of data in an internal memory. The data can be read out later on an analog or digital recorder. An internal pump pulls airborne dust into the sampling section, which contains a low-energy beta-ray source and a Geiger counter detector. No beta radiation escapes from the instrument, and no license is required for the operator. The mass concentration measurement is made while the dust is still airborne. Beta-ray attentuation is independent of particle size and composition of the dust, so the HCDM can he used with many types of dusts which may be airborne in flammable concentrations. A knowledge of the composition and minimum explosive concentration of the dust is necessary to understand the significance of the data from the HCDM. The HCDM was designed to measure air-

Jan 1, 1982

By R. V. Ramani, A. S. C. Owili-eger

The rapid depletion of shallower coal reserves dictate that mining in the future will be deeper and more complex with more difficult natural conditions. Consequently, an increase in methane emission is expected. It is becoming evident that more accurate predictions and better planning are necessary to design efficient methane drainage systems. This objective can be achieved by the utilization of the knowledge of the physics of gas flow through coal seams and rock strata and by the application of digital computers in the solution of methane flow problems. Although the methane emission models described here have not been adequately applied to existing field operations, good agreement between actual field measurements reported in literature and the simulation results indicates the potential of these models for initial flow quantity approximations and ventilation planning. This report has, therefore, introduced to the mine operator yet another application of computers as a planning tool. AREAS FOR FURTHER RESEARCH The study reported here is by no means complete. Extensive research efforts should be directed to the following areas: (a) Better understanding of the physics of gas flow through porous media which exhibit fracture permeability. (b) Determination of field parameters which control gas migration. (c) Investigation of the effects of the rate of penetration on the emission rate and fracture propagation.

Jan 1, 1974

By Christopher Mark

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

By Henry M. Harris, George J. Carter, Karle G. Strandberg

Field and laboratory data were used to evaluate sand from 13 dune locali­ties along the Oregon coast between Fort Stevens and Coos Bay. Chemical and glass button analyses were used to classify the 65 samples into two geographic zones of decreasing iron concentration. These data and data from preliminary magnetic beneficiation tests indicated that the sands between the Umpqua River and Coos Bay contained fewer impurities and were easier to beneficiate than those from areas between Fort Stevens and the Umpqua River, In addition, the dunes in the Umpqua River-Coos Bay area are the largest along the Oregon coast and are most favorably located with respect to existing transportation facilities, A composite sample from the Rogers area on the west bank of the North Slough of Coos Bay was selected for detailed mineral dressing studies. Splits from this sample were treated by various processes including magnetic separa­tion, electrostatic separation, flotation, and acid leaching, Concentrates were evaluated in glass melting tests. Test results indicated that high intensity magnetic separation followed by acid leaching would produce a prod­uct that could be used in amber and clear container glass batches. Good glass sand concentrates were also prepared by froth flotation; however, recovery was low and reagent costs excessive.

Jan 1, 1964

By R. V. Ramani, A. S. C. Owili-eger

The quantity of methane emitted into the mine atmosphere and the movement of gas through solid coal and the adjoining country rock are dependent on the physical properties of the medium, boundary con¬ditions, the initial gas pressure distribution, and the combination of natural and mining factors. Functional relationships between these factors are not yet known. Consequently, the development of rigorous mathematical models to predict methane flow into the mine air is difficult and to date no model has been reported which is capable of such a function. Thus far, empirical formulas available for the calculation of gas quantity released from underground sources require too much his¬torical data, not currently available. Again, these estimations are at best only crudely approximate. The numerical methods available have not been made practical enough for industry wide application. Therefore, the development of a relationship amenable to numerical analysis and practical enough for use in the industry would provide the flexibility lacking in analytical approaches. The mathematical models given in equations (7) and (8) are further attempts in presenting practical models for predicting the quantity of methane emission into the mine environment. Equation (7) is the steady state model and equation (8) is the unsteady state model.

Jan 1, 1974

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999

By C. Sunderman, J. Johnson, S. Signer

Researchers at the National Institute for Occupational Safety and Health have developed a miniature data acquisition system (MIDAS) that can measure resistance changes and temperature, store data for later retrieval, and illuminate LED lights. This instrument can be used with strain-gaged bolts, cable bolts, CSIRO stress-measuring gages, string pots, and any other instrument that uses single-ended, resistance-type gages. MIDAS has the capability to measure up to 16 gages at preset time intervals and store more than 2000 scans, yet is small enough to fit in a 35-mm hole. Because the MIDAS consumes little power, a 9-V alkaline battery will operate the system for 6 months. Data from the MIDAS can be sent to a PC via an RS232/RS485/IRdA port. A software program was written to set operation parameters, graph data, and store all information directly to a spreadsheet. Three LED lights change from green to yellow then red based on reading levels and/or rates of change. This feature can be used with different types of gages to warn miners of possible rock instabilities. The MIDAS has received MSHA experimental permissibility approval and is currently being tested at several mines.

To develop an in-mine water treatment system in which bacterial sulfate reduction and limestone dissolution continuously remove metals and acidity from contaminated drainage. Approach A section of mine tunnel was converted into a water treatment bioreactor by constructing cinder block dams and fang the area between them with a porous substrate mixture of limestone gravel and compost. Readily fermentable materials such as dairy whey, spent brewing yeast, or sugar were periodically added to the reactor. Mine drainage was impounded behind one of the dams and continuously percolates through the reactor substrate at a controlled rate. How It Works The reactor substrate soon becomes anaerobic after it is saturated with mine water. Under anaerobic conditions, sulfate-reducing bacteria consume the organic materials that are added to the reactor and generate hydrogen sulfide (HIS) and alkalinity. The H2S reacts with dissolved iron and heavy metals to form metal sulfide precipitates. The alkalinity raises the pH of the water and induces aluminum to hydrolyze and precipitate as aluminum hydroxide [Al(OH)3]. Additional alkalinity is generated by the continuous dissolution of the substrate limestone. Metal sulfide precipitates and Al(OH)3 are retained within the reactor, and the treated water is discharged. The underground location of the system allows year round operation.

Jan 1, 1994

By Dean H. Ambrose

This paper presents an approach for representing and analyzing random motions and hazardous events in a simulated three-dimensional workplace, providing designers and analysts with a new technique for evaluating operator-machine interaction hazards in virtual environments. Technical data in this paper is based upon a project striving to reduce workers' risks from being hit by underground mining machinery in a confined space. The project's methodology includes human factors design considerations, ergonomic modeling and simulation tools, laboratory validation, and collaboration with a mining equipment manufacturer. Hazardous conditions can be analyzed in virtual environments using collision detection. By simulating an operator's random behavior and machine's appendage velocity, researchers can accurately identify hazards, and use that information to form safe design parameters for mining equipment. Analysts must be discerning with the model and not read more from the databases than what the simulation model was designed to deliver. Simulations provided an interesting approach to data gathering in that there was no need for live subjects and logistics - test sites and costs associated with experiments-became insignificant. Collisions versus speed, operators' size, and risk behaviors proved the versatility found in the data obtained from the model. Preliminary results show that response time significantly affects the number of collisions experienced by the virtual subject. Also simulation data suggests that more mishaps occur with hand-on-boom-arm risk behavior.

Provide the technology to remotely control a thin¬-seam continuous mining machine from a safe location hundreds of feet outby the working face in an underground room-and-pillar mine. Background and Approach Hard-wired or radio remote control of continuous mining machine has been commercially available since the early 1970's. This type of remote control, in low and high coal seams, situates the machine operator offboard, but within direct view of the underground coal face, Although positioned under supported roof, the operator can still be exposed to face area hazards that include roof-rib falls, dust, methane explosions, and equipment congestion. The U.S. Bureau of Mines approach has been to put the operator into a protected compartment at a location away from the working face. Since 1979, the Bureau has investigated innovative methods to better protect face area workers in under¬ground room-and-pillar mines. In 1989, the Bureau demonstrated an offboard, computer-based remote con¬trol system in a West Virginia highwall mining operation that stationed the operator hundreds of feet away from the working face. In late 1992, much of this technology, plus improvements, Was used to demonstrate, on the surface, how a thin-scam continuous mining machine could be remotely controlled 200 feet from the machine in a 36-inch working height.

Jan 1, 1992

By Thomas V. Falkie, R. Venkataramani

Underground coal winning operations can broadly be classified as conventional, continuous, and longwall mining. In conventional mining, the operations of cutting, drilling, blasting, loading and hauling, and roof support are performed in that sequence in each working face in a work area. The major difference between continuous and conventional mining is that the coal is cut and loaded by a continuous miner in the former, thereby combining the unit operations of cutting, drilling, shooting, and loading into one. Longwall applications have been viewed with great interest in recent years, and although at the end of 1970 there were only 37 longwall installations in the U. S. with combined production of less than 4 percent of underground total, there is no question about the growth potential of longwall in the United States. Increased capacity, versatility, and power characterize continuous miners today. Although continuous miners have outsold conventional gathering-arm type loading machines for some years, the latter, in the new extra-high capacity types, are continuing to find wide use. Whether the mining system is continuous or conventional, the haulage units may include six-wheel articulated shuttle cars, tractor-trailer units, or extensible belt and bridge-conveyor systems, all tending to increase the productivity of the face units. The decision as to which to choose - continuous or conventional mining - is complicated, and both systems are capable of high production rates. Most continuous miners in use today have a revolving pick-mounted drum to cut the coal and a gathering arm loading unit. Functionally, there is little difference between the loading unit in a

Sep 1, 1972

To develop a quick, safe, and effective method that allows workers at mineral processing operations to clean their dust-soiled clothing periodically throughout the workday. Background Reducing workers' respirable dust exposure to silica and other harmful dusts and contaminants is an ongoing goal in the U.S. mining industry. One area of known worker exposure is from contaminated work clothes. A U.S. Bureau of Mines report documented a number of cases where a tenfold increase in a worker's dust exposure was measured from contaminated work clothes. In these cases, the dust emitted from clothing caused the worker's dust exposure to exceed the permissible exposure limit in less than 2 hours. The most effective way to eliminate this dust source is to have workers clean or change their work clothes. There are two federal regulations that impact the clothes-cleaning process. The first states that at no time shall compressed air be directed toward a person, but that when compressed air is used, then all necessary precautions shall be taken to protect persons from injury. The second regulation states that compressed air should only be used for cleaning purposes when it is less than 30 psi and used along with personal protective equipment. For the mining industry, by default, the only approved method to perform clothes cleaning is to have workers vacuum their clothes using a HEPA filter system. This is very difficult and time-consuming and, in most instances, not very effective. Most workers would prefer to use a single compressed air hose to blow dust from their work clothes. However, not only is this method prohibited by law, it usually creates a significant dust cloud in the work environment and contaminates coworkers.

May 1, 2005

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

SUMMARY AND CONCLUSIONS This report describes a study to develop a detailed set of guide¬lines and equipment recommendations to be used as a guide for mine operators, mine inspectors, and equipment manufacturers in implementing the emergency escapeway standards for metal and nonmetal underground mines. It was sponsored by the United States Bureau of Mines. The first part of this report reviews the historical background of metal and nonmetal mine fires and the development of present and proposed mandatory standards. This is followed by a discussion of the survey of representative mines and how the proposed standard effects these mines. The remainder of the report covers technical discussions of each escapeway component including a comprehensive computer sim¬ulation of mine evacuation. Following the technical discussion of each group of escapeway components is a list of the pertinent guidelines. A study of past mine fires indicates that a serious commitment by operators to the proposed escape standards would be instrumental in saving lives in the future. The most significant event in a recent mine fire, in which no deaths resulted, was the very early discovery of the fire. The evacuation was orderly thanks to careful preparation by the mine personnel. However, the mine was possibly only spared a real disaster because of the discovery of the fire almost at its inception. Installation of automatic fire and smoke warning devices may be the single most important step in preventing future disasters. The self-rescuer has saved many lives in mine fires. Men have also died while attempting to use them. The reason men died was either because the unit was not working or the miner did not understand how or when to use it. There is no good excuse for either of these conditions occurring. Regular maintenance and inspection should prevent unit failures. Frequent instruction on when and how to use the self¬rescuer would prevent confusion and potential fatalities. A means of

Jan 1, 1976

By R. J. Matetic

Researchers associated with the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), are investigating injuries (fatal and nonfatal) attributed to water well drillers during well drilling activities. Injury data, obtained from various sources, suggest that many water well drillers are experiencing unnecessarily high insurance premiums and very avoidable citations or violations from the direct result of accidents, injuries, and fatalities occurring throughout the water well drilling industry. Expensive insurance premiums and unnecessary citations are the direct result of poor health and safety practices. Visits to numerous water well drilling sites were conducted by NIOSH personnel to characterize and identify the injury data collected and to provide inexpensive strategies to prevent, minimize, and eliminate safety and health issues associated with water well drilling activities.

Jan 1, 2001

By Robert King

Splicing portable trailing cables used in underground coal mines is usually less expensive in terms of capital outlay and production time lost than replacing them. However, handling trailing cables may result in electrical arcs, shocks , and burns. Also, destructive forces encountered during a mining operation may shorten the effective life of a cable splice. This report gives the results of an analysis of cable splice defects in an effort to establish cable splice performance criteria, determine testing standards for cable splices, establish guidelines for training programs in cable splicing, and indicate areas for improvement.

Jan 1, 1975

By Maria I. De Rosa

This report analyzes mobile equipment fires for all U.S. surface and underground coal and metal/nonmetal mining categories by state and 2 year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from MSHA mine fire accident publications and verbal communications with mine personnel. The analyses will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the hazards associated with mobile equipment fires and will create a basis for future fire research programs.

Jan 1, 2004

By R. W. Freedman

The Bureau of Mines has developed a gas chromatographic method for the rapid and accurate determination of oxygen, nitrogen, carbon dioxide, methane, and, if present, carbon monoxide in mine air. This method replaces such presently used gas-reaction types as the Haldane or Orsat analysis, offering advantages in terms of precision, accuracy, speed, and convenience.

Jan 1, 1968

Protect rescue workers fighting fires or mine personnel temporarily working in hot environments from heat stress. Approach A specially designed ice-cooled vest is worn while working in hot environments where cooling the mine air is not possible. How It Works The vest holds a total of 44 individual ice cells in packets that are firmly held near the wearer's skin. These ice cells remove heat from the wearer, reducing heat stress and increasing comfort. The locations of the ice cells and packets are shown in the diagram. The vest is constructed in three layers with the outer layer being aluminzed fiberglass cloth. Its aluminized surface reflects radiated heat, and its fiberglass cloth provides fire resistance and strength.

Jan 1, 1979

By P. Yant, A. C. Fieldner

"IntroductionIn its investigations relative to reducing the hazards of carbon monoxide poisoning, the Bureau of Mines recently had its attention drawn to a compound2a sold under a trade name for which claims are reported to have been made regarding its efficacy in reducing that type of poisoning in automobile garages. Accordingly, some of the product was obtained and analyzed for its power to absorb, oxidize, or destroy carbon monoxide; and the results are herein reported.Description of ""Compound"" (quoted from manufacturer's circular)While the circular does not actually state that the ""compound"" protects against carbon monoxide, the inference is therein, because each of the two following quotations is below these respective headings; ""Carbon-Monoxide Poisoning,"" and ""Chronic Gassing Among Garage Workers.""The ""compound"" holds chlorine and oxygen gases in solution with formaldehyde, which unites with the hydrogen to form hydrochloric acid., giving an over-supply of oxygen which burns up carbon just as a piece of wood is burned in the fire. The formaldehyde in the composition of the ""compound"" is a great affinity for ammonia and hydrogen sulphide."

Apr 1, 1924

By William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to support the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977