Search Documents

By Richard J. Mainiero

The Bureau of Mines investigated coal-mine-type short-delay electric detonators marketed by three domestic manufacturers to determine the accuracy of delays and the probability of overlap between adjacent de- lay periods. The Winzer index was computed and compared with the probability of overlap. A close agreement between the Winzer criterion and overlap probability was demonstrated. A permissible blasting unit capable of delivering a maximum firing energy of 4.0 J and a digital oscilloscope were used to measure the delay time with an accuracy of 20.25 ms. Another oscilloscope and a pulse transformer were used to record firing current. Experimental data indicated negligible overlap probability in detonators of shorter delay periods: periods 1 to 4, which correspond to 25 to 250 ms. However, a significant probability of overlap was detected in some detonators of longer delay periods: periods 5 to 9, which cor- respond to 300 to 500 ms.

Jan 1, 1985

Table XXXIII itemizes the cost associated with the installation of an irrigation system and the application of latex and water in the three experimental areas at Lanse. There were no external labor charges (non- Research Center) except for the installation of the water meter. Cost of pipe and fitting are high because long lines were required at each of the three different locations; these costs were minimized by using plastic instead of metal pipe. Fifteen of the seventeen drums of latex received were used, five drums for each area. [ ] In tank-car lots latex would cost about $0.25/lb so that raw material cost for a 4000 lb/acre application would be in the range of $1,000 per acre. Equipment costs for setting up and irrigation are sensitive to size of area to be irrigated, design of system, and availability and cost of water. A realistic range is estimated to be between $200-500/acre.

Jan 1, 1972

Develop design and support guidelines for coal mine entry intersections based upon results of integrated field and numerical modeling analyses of structural parameters for improving ground stability. Background Underground coal mines contain a large number of entry intersections. Dome-shaped zones over the intersections are unstable and are often associated with roof falls. These roof falls may occur during mine development, trapping equipment and endangering miners. These high-risk areas of the mine account for 10 pct of the total number of ground-failure-caused fatalities. The falls, ranging from heights of 1 to 20 ft, cause high dilution and slow the advance rates. Stability at intersections is influenced by four structurally interrelated parameters: in situ stress, geological discontinuities and physical properties, intersection geometry, and roof span. Because of the complex interaction of these parameters, the actual mechanism of roof failure may vary considerably, depending upon the roof lithology, rock strength, and stress conditions.

Jan 1, 1990

By M. S. Seehra, R. S. Pandurangi

"A comparative study of the intensities of the IR modes in the pjlotoacoustic and. FrIR spectroscopy of amorphous and crystalline SiO2 particles is presented. It is observed that in photoacoustic spectroscopy of amorphous SiO2, IR modes of surface species are enhanced by over an order of magnitude compared to the bulk IR modes of SiO2. This effect, though not yet understood, may find applications in surface science.Since the publication of the Rosencwaig-Gersho theory of the photoacoustic effect in solids in 1976 [1], a great deal of attention has been paid to the development .of photoacoustic spectroscopy (PAS) into an analytical technique for condensed matter studies, especially when combined with the modern Fourier transform infrared (FTIR) spectrometer [2-8]. PAS has now been applied to a variety of experimental situations [2, 3] and it is particularly suitable for opaque powders and for cases where ~ample preparation (e.g. mixing with KBr as is usually done in FTIR spectroscopy) is not desirable. Another area of interest is the depth profiling feature of PAS, which is studied by varying the modulation frequency of the incident radiation [2-8]. The one-dimensional Rosencwaig-Gersho theory for non-porous samples has been extended to other cases [9-12]. Recently it has become known [11, 12] that for porous samples with porosity the IR modes are enhanced by a factor proportional toe. This enhancement is due to the pressure wave set up in the interstitial gas in the porous sample and this enhancement has been reported by a number of groups [12-14].In this Letter we report the observation of anomalously large enhancement of the PAS signal for certain surface IR modes on the surface of amorphous silica particles. This observation differs from the previous reports in that certain surface modes are enhanced by over an order of magnitude compared to the bulk IR modes. Although the reasons for this enhancement of the surface IR modes in PAS are not understood at present, this observation may open up new approaches to the study of surfaces. Results of these initial observations are given in this Letter. ·Experimental studies reported here were carried out on an FTIR spectrometer (Mattson Instruments, Model Cygnus 100) equipped with an MCT detector. The same instrument was used for PAS studies in conjunction with an MTEC (Model 100) PA cell. The sample cell and the spectrometer are continuously flushed with dry, CO2 free air obtained by the use of Balston Instruments Air Dryer Filter System (Model 75-60). Usually data were collected for 32 scans at 4 cm-I resolution, although both scan and resolution can be varied. For FTIR studies, samples were mixed with IR-grade KBr and pelletised. For PAS, no sample preparation is necessary and data are ratioed against dry carbon black [4, 5]."

Jan 1, 1989

By Fred N. Kissell, Jay F. Colinet

The two major lung diseases of miners are "blacklung" and silicosis. Blacklung, or pneumoconiosis, was first recognized as a disease of British coal miners in the 1600s. However, investigations into the cause of blacklung disease did not begin until the 1900s. The causative agent of pneumoconiosis in coal miners was thought to be silica until studies in the United Kingdom provided evidence that expo- sure to coal dust containing minimal silica could also cause pneumoconiosis. In the Federal Coal Mine Health and Safety Act of 1969, coal workers pneumoconiosis (CWP) was defined as "a chronic dust disease of the lung arising out of employment in an underground coal mine." Diagnosis of CWP is generally based on chest x-ray findings and a patient's history of working in coal mines, usually for 10 or more years. In its early stages, CWP is called "simple CWP." Miners with simple CWP are at increased risk of developing an advanced stage of the disease, called "progressive massive fibrosis" pMF) or "complicated CWP." PMF (complicated CWP) is associated with significant decreases in lung function and oxygen- diffusing capacity. PMF is also associated with breathlessness, chronic bronchitis, recurrent chest illness, and episodes of heart failure. Coal miners with silicotic lesions or PMF have an increased risk of tuberculosis and other mycobacterial infections. PMF may progress even in the absence of further dust exposure. This disease is also associated with increased mortality (National Institute of Occupational Safety and Health [NIOSH] 1995). The most recent study to determine the prevalence of CWP in coal workers was in the mid- 1990s. The average prevalence of CWP was 2.8%, but for those with 30 or more years in the industry it was 14%. For the 10-year period from 1987 to 1996, 18,245 deaths were attributed to CWP. The most frequently recorded occupation on the death certificate (70%) was mining machine operator (NIOSH 1999). Silicosis may develop when inhaled respirable crystalline silica (quartz) is deposited in the lungs. The clinical diagnosis of silicosis is based on (1) recognition by the physician that the level of silica exposure is adequate to cause the disease, (2) the presence of chest radiographic abnormalities consistent with silicosis, and (3) the absence of other illnesses (e.g., tuberculosis or pulmonary fungal infection) that may mimic silicosis. The radiographic patterns are often the same for CWP and silicosis; thus, these diseases are sometimes distinguishable only by work history or pathological examination. Chronic silicosis commonly involves 15 or more years of exposure to silica. The characteristic microscopic feature is the silicotic nodule. Chronic silicosis is often asymptomatic and may manifest itself as a radiographic abnormality with small, rounded opacities of less than 10 mm in diameter, predominantly in the upper lobes. Lung function may be normal or show mild restriction. Chronic silicosis is also associated with a predisposition to tuberculosis and other mycobacterial infections and with progression to complicated silicosis.

By David C. Byrne

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals. Also, miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupational Research Agenda, problems created by occupational hearing loss include (1) the reduced quality of life due to social isolation and unrelenting tinnitus, (2) impaired communication with family members, the public, and coworkers,(3) a diminished ability to monitor the work environment (e.g., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers’ compensation and hearing aids. Although the elimination of hazardous noise is the ideal long-term solution to the noise problem, miners will likely need to rely on personal hearing protection in certain situations for quite some time. However, it is well known that noise attenuation provided by hearing protectors as they are worn during everyday use in the workplace is usually worse than when tested under laboratory conditions. Additionally, workers may refuse to wear their hearing protection for any number of reasons. Therefore, this project was initiated to evaluate practical technological advances in hearing protectors, with an emphasis toward optimizing the balance between effectiveness, comfort, overprotection, and communication ability. Currently, the necessary in-house laboratory facilities and research techniques are being finalized. Individual experiments are planned that involve analysis of new hearing protector technology under both laboratory and field conditions. The laboratory components are to consist of con-trolled studies using human subjects and/or an anthropometrically correct artificial test fixture to evaluate the adequacy/effectiveness of various hearing protective devices. Field studies are planned to determine the actual usefulness and practicality of the hearing protectors as used in diferent mining environments. Recommendations can then be offered to the mining community regarding correct earplug/earmuff usage that maximizes recognition of hazard/warning sounds while adequately protecting the miners’ hearing.

Jan 12, 2000

By A. C. Fieldner

It is estimated that 6,202,235,000 gallons .of- gasoline was produced during the year 1922. The crude light oil- output Burin- the same year is estimated at 111,000,000 gallons, or 1.8 per cent of the gasoline production. In fact, if all the coal mined were coked in by-product ovens, and the light oil recovered therefrom, this product would amount to only 15 to 20 per cent of the quantity of the petroleum gasoline now produced annually. It is obvious therefore, from these figures that the light oils by present coking processes can not assume great importance as a gasoline substitute in a national sense. However, the use of light oil as a motor fuel is of real importance in districts adjacent to by-product coking operations from which a reasonable proportion of the local motor fuel supply may be derived. The certainty of diminution of petroleum resources in the relatively near future demands the utmost utilization of gasoline substitutes from the distillation of coal as well as other sources. Motor benzol is a by-product from the destructive distillation of coal. From 11/2 to 3 gallons of refined motor benzol is obtained per ton of coal carbonized. The light oil vapors are extracted from the by-product coke-oven gas by passing it upward through a series of towers in which these vapors are absorbed in a descending current of "wash" oil (petroleum distillate). The light, oil is recovered from this wash oil by distillation with live steam, the resulting crude light oil consisting of a mixture of benzol, toluol, xylol, solvent naphtha, and a small amount of other substances (unsaturated hydro-carbons, carbon disulphide, and other sulphur compounds, phenols and pyridines) is then transferred to an intermittent still and fractionated into crude motor benzol, which includes the toluol and a part of the xylol or light solvent naphtha. The crude, motor benzol is yellow in color, contains sulphur compounds which corrode copper and brass, and also contains unsaturated bodies which oxidize and polymerize on standing, producing sediment and forming gummy deposits highly objectionable when the benzol is used in motors. These objectionable

Jan 1, 1923

By D. B. Taliaferro, David M. Logan

which an operator may obtain detailed information regarding all projects in the State. It is the purpose of this report to present data such as volume of oil produced monthly, volume of water injected monthly, spacing of wells, number of injection wells and oil wells, and other such pertinent information regarding every project in the State whether active or abandoned and whether a success or a failure. It is believed that with these data it is possible to analyze water-flooding operations in this area more completely than has been possible in the past. As the title indicates, the report is essentially a history, and ordinarily no opinion is given as to the cause for the success or failure of individual projects. Increasing the production of oil is exceedingly important at this time, and one method by which it may be done most readily is by providing additional energy for the movement of oil in many of the older fields. In many oil fields the predominant force that drives oil through the porus reservoir rocks to wells is the gas dissolved in or otherwise associated with the oil under pressure. As the pressure in the reservoir declines in consequence of the removal of fluid, gas comes out of solution in the form of minute bubbles; as the pressure is reduced further, the expansion of these bubbles forces part of the oil toward the areas of lowest pressure and into the producing wells. The physical properties of the oil and the gas governing their flow through reservoir rocks to wells differ, and much of the gas slips past the oil leaving large quantities of oil in the reservoir when the pressure has been exhausted. Often the natural productive life of fields is prolonged by reducing the pressure in oil wells below atmospheric with vacuum pumps; but the ad- ditional energy made available in this manner is limited to less than 1 atmos- phere of pressure, and even after the extended application of "vacuum" to a petroleum reservoir large quantities of oil are left unrecovered in the porous rocks and sands.

Nov 1, 1943

By S. H. Denny

"As the result of the work of an efficient safety organization, the Midwest Refining Co. at its various operations and particularly in the Salt Creek field has been able to show a definite accident reduction. Lost-time accidents during the past year have been reduced to a small number as compared with previous years, and infection cases have been almost eliminated.The accident-prevention work of the Midwest Refining Co. is in charge of the department of industrial relations, with a director as the administrative head; two safety men handle the work directly at Midwest, Wyo. A competent medical staff with a well-equipped hospital at Midwest is also an important factor in the prompt and proper treatment of injured persons when an employee is injured, he is given first-aid and then taken to the hospital with minimum delay.About 1,450 persons are employed in the 4 departments (production, gas, pipe lines, and electrical) and in the 34 districts of the Midwest Refining Co. The work at Midwest spreads over a considerable area, and new drilling operations, pipe work, and similar activities require the services of many small gangs of workers. Complete supervision, of each job, whether shall or large, is possible through the large number of superintendents, foremen, and gang pushers employed; thus, there are 20 superintendents, 78 foremen, and 115 gang pushers. The largest number of men under any one toss is approximately 15, and it is probable that much of the good safety record is due to this intensive supervision. These company officials, including the gang pushers, have been impressed with the idea that it is their duty to see that the men under them do not get hurt; the responsibility of instructing new employees in safety practices is placed directly upon them. Monthly meetings of the field officials, including superintendents, foremen, and gang pushers, and as far as possible the men, of each district are held with the safety engineer. Both officials and men are encouraged to bring up for discussion any practice or proposals looking to the changing of any conditions that will"

Apr 1, 1928

By S. B. Flagg, J. F. Barkley

In the past few years an awakened activity in power-plant econ- omies has resulted in a marked improvement in the equipment for generating and utilizing steam. Although the improvement in design and construction of steam-driven prime movers has been greater than that of the steam-generating equipment, the economies obtained with the more efficient engines and turbines have stimulated interest and activity in eliminating unnecessary boiler and furnace losses. Much attention has been given to the boiler room in efforts to obtain proper combustion of the coal, because of the importance of the coal item in costs of power production. As evidence of this increasing interest may be cited the record of the development within the past few years of new apparatus for the analysis of flue gases. Many new forms of apparatus have appeared, including those for the determination of carbon dioxide, oxygen, and carbon monoxide, and others for indicating and for recording the content of carbon dioxide only, as carbon dioxide content is usually a good indicator for the control of furnace operation. Because of the large number of steam-power plants operated by the Federal Government and the number of CO, recorders used therein the Bureau of Mines undertook to collect information regard- ing the practical application of such recorders. Articles published from time to time concerning CO, recorders have been mostly descrip- tive, giving little reliable information as to the results that could be expected from the various types of instruments in ordinary prac- tice, and most of the tests made have been of a laboratory nature. Tests of several different types of recorders were made under service and laboratory conditions in order to obtain needed information. The purpose of the Bureau of Mines in publishing the results is to show the factors which may affect the accuracy of a CO, recorder and the manner in which a recorder should be tested. Readers should note that the remarks on different recorders apply to the instruments tested and not to later instruments of the same makers. In the course of the tests the following details were determined: 1. The lag in recording changes of composition of a flowing gas. 2. The accuracy of each type of recorder.

Jan 1, 1916

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines lid some development drilling at the Milan deposit in an endeavor to find an additional source of supply of copper. The deposit, which is in Coos County, northern New Hampshire, is about 8 miles northwest of Berlin. It was discovered in the seventies and was worked steadily until 1886, yielding a monthly production of 2,600 tons of ore. Lessees opened the mine again in 1695 and mined 1,500 tons. The Milan Mining & Milling Co. acquired the property in 1907 and made regular shipments of ore and concentrates until 1910. From 1911 until 1938, the tract was held by a local resident for timber land, Ventures, Limited, a mining concern with headquarters at 25 King Street, West, Toronto, Canada, acquired the property in 1938. No production has been recorded since 1910. To cut the vein below the old mine workings and to search for extensions to the northeast and southwest, the Bureau of Mines diamond-drilled eight holes for an aggregate of 3,596.2 feet.

Jan 1, 1950

By John R. Reeves

The development of an new industry, which must prepare its marketable products at or near the source of the raw material, and ship them to a market which may cover half a nation, is more or less influenced by a number of natural and cultural conditions such as (1) location of plants with respect to a large market, (2) climatic conditions, (3) transportation facilities, (4) labor supply, and (5) water supply. An effort is made in this pager to give in detail a number of the more important of these conditions as they affect, either favorably or unfavorably, the development of the oil-shale resources of southeastern Indiana. The utilization of the New Albany formation for the production of oil will be similar to a large scale low-grade ore proposition in which the raw material can be obtained in very large quantities at a relatively low cost. It appears, therefore, in considering the value of this shale or its economic position in relation to other oil shales, tie cost of mining and preparation for the retort are of prime importance.

Jan 1, 1923

By Martin H. Stanczyk

Freezing to dewater typical Florida phosphate rock slime as demonstrated in laboratory tests appeared to have potential commercial use because of indicated moderate energy requirements, good compaction of dewatered solids, and effective recovery of usable water. After freezing, thawing, decanting, and filtering, batch freezing of gallon-size 13.7 percent solids slime samples yielded 42 percent solids products. Cationic amine, used as a process additive, yielded 46.8 percent solids product with significant filter area reduction. Semicontinuous 8 stage freezing tests also produced thickened slimes. Cooling and freezing 13.7 percent solids slime from 30° to minus 10° C required removal of 183 Btu per pound of slime; Carnot cycle calculation indicated that the theoretical minimum energy to transfer this heat was 27.8 Btu per pound. To produce 1 ton of 44 percent solids slime from 13.7 percent sol-ids slime, the calculated theoretical energy required for cooling and freezing was 52.3 kilowatt-hours. During the research heat capacity and heat of fusion data were determined for the slime at various percent solids.

Jan 1, 1971

By John R. Bartels, Dean H. Ambrose, Richard C. Wang

This paper presents the results of a study to verify and validate a computer model that represents and analyzes motions and hazardous events in a simulated three dimensional workplace. The purpose of the computer model is to support research that is investigating the safe speed range for the vertical movement of roof bolter boom arms to reduce worker injuries in underground coal mines. The information obtained for this paper is based upon a project that is investigating means to reduce workers risks of injury from exposure to mining machinery. The methodology being employed by the project includes human factors design considerations, anthropometric modeling and simulation tools, laboratory validation, engineering interventions, and collaboration with industry and an equipment manufacturer. The results of this study were used to (1) determine the input parameters that are unique to the mining environment and needed to develop a credible, computer-based, human-machine interactive model, (2) develop test methods to measure the required parameters, and (3) to refine the human-machine interactive computer model.

By M. A. Trevits, S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978

By H. V. Makar

A study was conducted by the Bureau of Mines to determine problems associated with the use of ferrous fractions from urban refuse as melting stock for steelmaking and to evaluate the resulting steel products. The study involved 50-pound ingots from laboratory melts and 50-pound ingots from 1-ton electric-arc-furnace melts. The 50 pound ingots from the laboratory melts and the arc-furnace melts were hot rolled to provide material for mechanical and corrosion testing. Results obtained in the study include the following: Most steels rolled successfully and exhibited acceptable surface and edge condition. Tensile strengths of the plain carbon steels were not significantly affected by copper up to concentrations of 0.65 pct and were not affected by tin content up to 0.16 pct. Yield strength increased with increasing copper and tin contents, and impact strength decreased with increasing tin content. Hardness increased slightly with increasing copper content. In general, properties of the steel produced were not measurably affected by charge composition (that is, melting stock), melting practice, or method of scrap preparation.

Jan 1, 1975

By Lisa Steiner, Robin Burgess-Limerick

In 2004, there were 646 underground coal mines in the USA employing 37,445 miners. These mines reported 3556 injuries to MSHA that year - 17% were associated with bolting machines (593 injuries), 8% with continuous miners (283 injuries), and 4% each with Scoop/LHD (1 51 injuries), shuttle cars (134 injuries), and personnel transport (145 injuries). The use of the frequency of reported injuries for the prioritization of risk control strategies has limitations because of the tendency to underestimate the importance of relatively rare but high-consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggest the following hazards as the highest priority for elimination or control: • rock falling from supported roof • inadvertent or incorrect operation of bolting controls • handling continuous miner cable • collisions while driving LHD/Scoop, shuttle cars and personnel transport • rough road while driving or traveling in LHD/Scoop, SC & PT

By W. P. Diamond, John C. LaScola, D. M. Hyman

In 1972, the Bureau of Mines developed a direct-method test for measuring the gas content of virgin coal core samples for coal mine health and safety considerations. Since that time, approximately 1,500 coal samples from more than 250 coalbeds in 17 States have been collected for gas content determination. The gas content data, when combined with geologic and engineering studies, can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if methane drainage in advance of mining should be considered. The data are also critical in delineating coalbed methane resources and in utilization feasibility studies. This report makes the Bureau's extensive data base of gas content data more readily available to the coal and gas industries. The data are presented in tabular form, alphabetically by coalbed name and by State. The components of the total gas content (lost, desorbed, and residual gas) are given, Location (State and county), sample depth, coalbed or formation name, and coal rank are included for geographic and geologic identification.

Jan 1, 1986

By John Jordan, Steven J. Knoll, Douglas Tesarik, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By Donald R. Irving

ALTHOUGH the quantity of material handled at metal and nonmetal mines in the United States in 1962 was 2.7 billion tons, the same as in 1961, a larger proportion was waste. At metal mines, crude ore production declined 1 million tons and waste output rose more than 18 million tons; at nonmetal mines crude ore production declined 6 million tons and waste output rose 36 million tons. Copper and iron ore producers increased their share of crude ore and material handled from about three-fourths to four-fifths of the national metals total, and sand and gravel and stone producers in-creased their share of the nonmetals total, also from three-fourths to four-fifths. Six States-Arizona, California, Florida, Michigan, Minnesota, and Utah-each handled more than 100 million tons of ore and waste, and together they accounted for 43 percent of the U.S. total. When the large-volume construction materials (sand and gravel and stone) were excluded from the totals, four States-Arizona, Florida, Minnesota, and Utah-supplied over half of the material handled.

Jan 1, 1963