Search Documents

By C. H. Elder, Maurice Deul

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coalbed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 ft3 /day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

To find solutions for common safety problems encountered in the handling of trailing cables, based on observations at many different surface mining operations. Approach Practices in handling trailing cables were Investigated through personal visits to over 40 mines, supplemented by visits to cable manufacturers and cable repair service companies. The most effective solutions to the safety problems en-countered were noted and are described In the project final report. Examples are given in this Technology News. Accident Experience Most cable-related injuries occur as a result of workers lifting, pulling, tripping, or being struck by the cable. The Table gives the frequency of occurrence for injuries reported during a recent 3 1/2 year period.

Jan 1, 1982

By M. K. Larson, J. K. Whyatt, F. M. Jenkins

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [F . 135 MPa (19,600 psi) oriented S 80E1W]. An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 1995

By G. R. Friggens

A nuclear method for continuously monitoring the coalbed and ash levels and void formation in commercial-scale, fixed-bed, pressurized gas producers is proposed. Measurement of gamma ray transmission through the coalbed is the basis of the method. The coalbed level is monitored by detecting the trans-mission of gamma rays from a 1 to 2 Ci Co-60 source positioned on the outside wall of the vessel. Coal bridging or, alternatively, ash level is monitored by a 10 Ci Co-60 source at the center of the coalbed. Source activities and geometries are calculated for a 12-foot-ID producer designed to operate at 350 psi. Source capsule and detector specifications and operational safety are also discussed.

Jan 1, 1973

By J. Ankrum, T. Xia1, D. Wilder, K. Spratt

The human lumbar spine is inherently an unstable structure and requires sophisticated neuromuscular control to maintain its stability and for performing physical tasks. As a consequence, it is important to understand the potential health effects on human operators of mechanical stimuli such as shock and vibration.1 Impact applied to a vehicle operator combines the risk of sudden, unexpected load with the mechanical stress of the seated posture.2 Because many work environments contain the potential for multiple, unexpected impacts, it is important to understand how the trunk muscles respond to complex conditions. We believe the results have implications for isolation design and standards development. Methods Muscle activity was recorded during simple and complex impacts, applied randomly and without warning, while subjects sat on an air-suspension truck seat located on a man-rated 6-DOF motion platform (Rexroth-Hydraudyne). Simple (single) impacts consisted of 100 ms quarter-sine jolts in the side-to-side (L and R) and vertical upward (V) directions with peak amplitude at 0.4 g. Complex impacts consisted of combinations of two simple (single) impacts in sequence (LV, RV, VL, VR), separated by 100 ms. Twelve right-handed males (23.7 ± 7.8 years old) were tested without a blindfold under 2 posture conditions (supported while leaning back and unsupported, sitting upright) and 2 seat suspension conditions (present or absent). Each type of impact was repeated three times under each posture and suspension condition, resulting in 84 impacts in total. Surface EMG signals from the left and right erector spinae (ES), rectus abdominis (AR), external obliques (EO) and internal obliques (IO) were recorded and transformed to 25ms RMS values. The response time, defined as the time the muscle activity exceeded the mean + 2 STD of the pre-impact resting period, peak response amplitude, and time were then derived. A mixed-model repeated measures analysis of variance was used to evaluate statistical significance, where type I error rate was set at .05. Results One question we asked of these data was whether there were differences in responses related to simple single strike impacts (L, R, or V) and complex, double-strike impacts (LV, RV, VL, VR). There are 21 possible combinations of comparisons of simple and complex impacts to each other. The differences found are listed in Table 1.

Jan 6, 2006

By J. B. Gayle

The Bureau of Mines sole-heated oven has been used for studying coal expansion for some 20 years. During the period before 1940 emphasis was placed on studies of the mechanism of coal expansion and the effects of variations in operating conditions on the results. Since 1940 emphasis has shifted to a survey of the expansion properties of various coking coals. Because additional information concerning a number of unsolved problems in connection with the earlier studies appeared highly desirable, this investigation of the use of sole-heated ovens for studying coal expansion was undertaken. The principal findings, in order of their discussion in the text, may be summarized as follows. 1. Expansion results for binary blends of coking coals exhibit nonadditive behavior, both positive and negative deviations from additive behavior being noted, depending on the particular coals tested. Additive behavior can be achieved, however, either by charging the blend components in separate layers (which indicates that the observed phenomena are not characteristic of the particular expansion oven used) or by testing relatively coarse sizes of coal (which suggests that the effects of crushing on the expansion properties of coking coals may be even more complex than is generally recognized).

Jan 1, 1959

By R. D. Leitch

"INTRODUCTION This report is another of the series on the effect of drouth and low water on the pollution of streams by coalmine drainage. A previous report3 dealt with work on Bennett Branch of Sinnanahoning Creek, Pa. This report deals with the results obtained during a similar study of Black Lick Creek, Two Lick Creek, and Yellow Creek. All of these belong to the same drainage system. Two Lick Creek is a tributary to Black Lick Creek, and in turn Yellow Creek is a tributary to Two Lick Creek, as shown in Figure 1.Black Lick Creek was of such a volume that a seasonal investigation was not entirely feasible. Yellow Creek was found to have mines only near the mouth, except a few of status unknown to the writer at the extreme head-waters, and the stream was also more or less inaccessible for regular and frequent sampling. Two Lick Creek was found to be most suitable of the three.ACKNOWLEDGMENTThe work reported has been carried on under the direction and with the advice of Dr. R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station."

Jul 1, 1931

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

5. General Escapeway Requirements 5.1 Escape Routes Present escapeway regulations state "Every mine shall have two separate properly maintained escapeways to the surface which are so positioned that damage to one shall not lessen the effectiveness of the other, or a method of refuge shall be provided when only one opening to the surface is possible." "Escape routes shall be a. Inspected at regular intervals and maintained in safe, travellable condition, b. Marked with conspicuous and easily read direction signs that clearly indicate the ways of escape." "Application. "Regular" intervals means at intervals no greater than monthly where conditions are stable and oftener where conditions may change." "Designated escapeways inclined more than 30* from the horizontal shall be equipped with stairways, ladders, cleated walkways, or emergency hoisting facilities." As can be noted in present and proposed regulations there must be two separate properly maintained escapeways. In most operations, the escapeways will consist of one route that is the normal travelway used in day to day operations. The second route is usually a return airway through old work areas. Based on this generally accepted practice, we will designate the two types as primary and secondary.

Jan 1, 1976

By Harold L. Rhodes

Vapor-liquid equilibria data for 65-34-1 and 25-27-48 mole percent helium-nitrogen-methane mixtures are presented for 12 temperatures from 76.5° to 164° K and pressures from 100 to 1,200 psia. These data were obtained in a windowed phase equilibria cell equipped with a vapor recirculating pump. Isobaric and isothermal K-values are plotted for both mixtures. Two isometric plots are included.

Jan 1, 1972

By R. F. Abernethy

A chemical method of determining microgram quantities of arsenic in coal was investigated by the Bureau of Mines to supplement a semiquantitative spectrographic method of determining arsenic in coal ash. In accordance with a method recommended by the International Organization for Standardization, 1-gram samples of coal are decomposed by wet oxidation with boiling sulfuric acid (H2S04) and nitric acid (HN03) to remove the organic matter. After heating to fumes of SO3 to remove HN03, the arsenic is separated as arsine by the action of zinc in H2S04 solution. The arsine is absorbed in dilute iodine solution in which the arsenic is determined colorimetrically by the molybdenum-blue reaction. Two modifications of the method for obtaining the arsenic in solution, in addition to the wet oxidation method, give satisfactory results. The modifications are (1) furnace ashing with MgO added to the coal, followed by treatment with H2S04, and (2) extraction of arsenic from the coal by dilute HNO3 without ashing. Float-and sink-tests show that arsenic is associated mainly with mineral matter in the three coals examined. High-temperature ashing tests show that very little arsenic is volatilized from coal ash below 1,000° C, but it is virtually all removed from the ash at 1,300° C.

Jan 1, 1968

By R. R. Sayers

"According to the dictionary,3 an accident is an event that takes place without one's foresight or expectation, often an undesigned, sudden, and unforeseen occurrence of an afflictive or unfortunate character. However, actual experience with accidents, the second most important cause of death in the United States,4 and a more extensive and scientific inventigation of their causes indicate that from 75 to 90 per cent of accidents are avoidable.5 This is borne out by the results of a three-year study of the accident records of 64,000 motor vehicle operators in New York6 which show that certain drivers are prone to accidents, that accident experience is traceable to certain causes, and that accidents don't just ""happen,"" It is estimated that 97,000 persons were killed by accidents in the United States in 1929 and 15,000,000 were injured. Of these about 23,000 deaths were due to so-called industrial accidents. In a list of accident rates by industries, compiled by the National Safety Council7 from reports of member establishments, mining heads the list, in both frequency (74.43 per 1,000,000 man-hours worked) and severity (9.9 days lost per 1,000 man-hours worked). These figures are very much higher than for any other industry; theindustries showing figures most comparable to mining are meat packing with a frequency rate of 55.94 and a severity rate of 1.47, construction with a frequency rate of 50.41 and a severity rate of 4.62, and refrigeration with a frequency rate of 43.35 and a severity rate of 3.04.While there is no way to determine the actual cost of all accidents from a monetary standpoint, estimates indicate that the cost will run into hundreds of millions of dollars annually.Cost of accidents in metal mines.- The United States Bureau of Mines obtains accurate figures on the number of lost-time nonfatal accidents as well as fatal accidents in the metal-mining industry.8 In 1926 the metal mines employed 127,823 men; 430 men were killed and 30,350 men received lost-time but nonfatal injuries as a result of accidents. Each of these fatal and nonfatal injuries averaged 114 days lost time, computing a fatality as 6,000 days lost time. This is equivalent to 3,523,944 days time lost due to accident, or at $5 per day per man, to a wage loss of $17,619,720. Deducting one-ninth of this figure for compensation paid, the metal miner loses in wage annually about $15,700,000, or about $122 per individual. This average loss per individual includes the cost of fatal accidents reckoned at 6,000 days or $30,000, but even if the loss in time due to fatal accidents be deducted, the average cost to each individual metal miner each year for nonfatal accidents is about $32. Estimating the loss to the metal-mine employer as about the same as that to the employee, the annual cost of metal-mine accidents to the employer is about $15,700,000 and to the employer and miner is $31,400,000."

Oct 1, 1930

By M. L. Odenbaugh

The viscosity reduction effect of varied concentrations of leonardite (a naturally oxidized form of lignite) and leonardite-caustic on the rheological properties of a standard bentonite drilling fluid was studied and evaluated. The minimum plastic viscosity was found to occur at application rates of 4 lb of leonardite and 1.33 lb of caustic per barrel of drilling fluid. Leonardite-caustic treatment was not beneficial in treatment of salt-contaminated drilling fluids. Although filter loss rate was reduced; both yield values and gel strength were increased. Compared with other viscosity control agents) including quebracho) ligno-sulfonate) humic acids extracted from leonardite) as well as other reaction products of lignite) leonardite is less effective at low application rates but is an effective treating agent at rates of 2 Ib/bbl or more. Considering the comparable merits of the substance tested) the major factor in determining which agent to use should be based on cost consideration.

Jan 1, 1967

By James J. Olson

The Bureau of Mines recorded peak particle-velocity levels and vibration frequencies to determine the nature and intensity of ground vibrations for tunnel blast rounds at the NORAD Complex, Colorado Springs, Colo. Previous Bureau of Mines studies in quarries and underground mines had shown that scaling (dividing) the distance from the blast by the square root of the charge weight removed the effect of the various charge weights on vibration amplitudes. The analysis of variance tests performed on the NORAD vibration data, however, indicated that the cube rather than square root scaling exponent grouped the data more effectively. The empirical propagation equation, V = 560 (D/w1/3)-2.04, where V is the maximum peak particle velocity in inches per second, D is the distance from the blast in feet, and W is the zero-delay charge weight in pounds described the attenuation, with distance, of the particle velocities from the tunnel blasts in the Pikes Peak Granite of the NORAD Complex.

Jan 1, 1972

By R. B. Prater

Research by the Bureau of Mines includes efforts to devise means for maximum recovery of critical and strategic metals from primary and secondary domestic resources. As part of that effort, the Bureau developed a hydrometallurgical process to recover Co, Ni, and Cu from Missouri lead-smelter matte. The process includes leaching with H2S04 plus Mn02 as an oxidizing agent, liquor purification, selective precipitation of CuS, (Co,Ni)S, and MnC03, and crystallization of Na2S04&apos; This report is concerned primarily with liquor purification, in which As and Fe are removed from the leach liquor by pH adjustment and filtration. Two variations of the purification step are described. One variation provides liquor containing <1 mg/L As and Fe but requires two solid-liquid separations, The other is achieved with only one solid-liquid separation but leads to a lower degree of purification.

Jan 1, 1987

By Richard J. Mainiero, Harry C. Verakis

The Bureau of Mines has conducted research to determine whether the total elapsed delay time for blasting bituminous coal in underground mines could be safely expanded beyond the present 500-ms limitation without igniting a methane or methane-coal dust atmosphere. The results indicated that the increase of total delay from 500 to 1,000 ms had no detectable effect on safety relative to incendivity as long as permissible practices were observed in all other aspects. Research was also conducted to evaluate the safety of 18-in hole spacing for delay blasting in coal relative to misfires. For a variety of permissible explosives, misfires were observed for about 50 pct of the holes at 18-in spacing. Based on this observation, the Bureau has recommended that the new regulations prohibit hole spacings of less than 24 inches in underground coal mines. Misfires were also observed for 24-in spacing, but the number of misfires and test shots was too small to sup- port any firm conclusions.

By Oliver C. Ralston

OUTSTANDING TRENDS of the year included the following: 1. Concentration and beneficiation of iron ores to provide improved blast-furnace feed and extend ore reserves. 2. Successful development of pelletizing and sintering procedures for fine iron ores. 3. The realization that cyclone separation could replace existing classifiers in many grinding circuits. 4. The rapidly blossoming metallurgy of ultrapure silicon and improvements in zone melting. 5. The rapid increase in the use of liquid-liquid extraction and ion exchange in hydrometallurgy. 6. The industrial application of vacuum melting on the 100-ton scale. 7. The hope for developing a columbium (noibium) base alloy for high-temperature use. The technologic advancement in metallurgy that had the greatest effect on the American economy was the beneficiation of iron ores to give improved feed for blast furnaces and indirectly extend our ore reserves. This was not a sudden development but rather culmination of a decade of intensive effort.

Jan 1, 1958

Reduce face methane concentrations and help prevent miners from working under unsupported roof while moving the curtain. Approach Use water sprays on the continuous mining machine to move and direct air to the face, and also provide appropriate installation guidelines for the most effective use of the system. I n laboratory tests and under actual mining conditions, the spray fan has proved an effective means of ventilation. Recent observations in the field, however, have shown that not enough technical information is widely available on proper installation of the spray fan. This Technology News is designed to rectify that situation by providing a concise guide for spray fan installation. How the System Works Good ventilation is essential for methane control. The spray fan system repositions regular water sprays to help the normal exhaust face ventilation do a more effective job. The various water sprays help in many ways: 1. Side sprays bring clean air along the side of the miner into the off-curtain corner.

Jan 1, 1983

By J. W. Horne

The quantitative determination of salt in petroleum ins generally divided into two steps - (1) extraction of salt from the oil and (2) accurate measurement of the extracted salt. This paper presents a method used by the Bureau of Mines for quantitatively extracting the water-soluble chloride salts4/ from petroleum and discusses important details attendant on the success of the method. Among these details are homogeneity in the dispersion of salt crystals, emulsified brine and other impurities in the oil sample, complete solution of the salt, and total extraction and titration of all the aqueous phase. Recently, the chlorides of sodium, calcium, and. magnesium produced with and present in various oils have developed growing problems of salt deposition and corrosion in the petroleum industry. Therefore, a technical study of various emulsions and salts that accompany petroleum is being made by the Bureau of Mines in cooperation with the State of Oklahoma. One report (5)5 reviewing the literature pertinent to the study has been published.

Jan 1, 1940

By J. W. Horne

The quantitative determination of salt in petroleum ins generally divided into two steps - (1) extraction of salt from the oil and (2) accurate measurement of the extracted salt. This paper presents a method used by the Bureau of Mines for quantitatively extracting the water-soluble chloride salts4/ from petroleum and discusses important details attendant on the success of the method. Among these details are homogeneity in the dispersion of salt crystals, emulsified brine and other impurities in the oil sample, complete solution of the salt, and total extraction and titration of all the aqueous phase. Recently, the chlorides of sodium, calcium, and. magnesium produced with and present in various oils have developed growing problems of salt deposition and corrosion in the petroleum industry. Therefore, a technical study of various emulsions and salts that accompany petroleum is being made by the Bureau of Mines in cooperation with the State of Oklahoma. One report (5)5 reviewing the literature pertinent to the study has been published.

Jan 1, 1940

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983