Search Documents

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"This report is () expansive test program by the Bureau of Mines to determine methods from various and ferrous manganese-grade product () widespread () and manfniferrous iron ores. Among the samples received for testing was one from the pits of the Barytes Mining Co., 1-1/ 2 miles northeast of Cartersville, Ga.. The property is approximately in the center of the Cartersville manganese district and shares a common corner with properties of the New Riverside Ochre Co. and the Etowah Development Co., both producers of manganifereus ores. The deposit is typical of the district and occurs in residual clays resulting from weathering of the Shady limestone and Weisner quartzite. 7/The property is developed by a number of open pits ranging to 60 feet in depth. In 1918 several carloads of manganiferous iron ore was mined from an alit on the property. Since then mining operations have been negligible. The ore is known locally as calico ore.A 4-ton sample representing -re as it occurs in the -pen pits vas furnished for testing. The sample consisted of a mixture of red iron oxides, wad, and clay, with small pebbles of manganese oxides and siliceous fragments scattered throughout."

Mar 1, 1943

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

7. Development of Acoustic Seal Checking System The acoustic approach was shown in Section 4 of this report to be the most promising concept for checking the seals. This section describes the development of this concept into a working hardware system to be used later in the field test program. This development effort included: (1) Theoretical analysis of the acoustic behavior in the mine using acoustic modeling- techniques. (2) Experimental determination of acoustic patterns in mine passages. (3) Refinement of the theoretical model. (4) Verification of final theoretical predictions in the quarter-scale laboratory model of a mine passage and seal. (5) Development of system specifications. (6) Development of the Acoustic Prototype Seal Checking System. 7. 1 Analysis of the Acoustic Seal Checker Concept The acoustic seal checker concept is based on a model which combines corridor acoustics and hole transmission theory. The idealized model for the mine sealing application is shown schematically in Figure 66. A high intensity acoustic- source is located in a corridor at a, position adjacent to the location to be sealed. The acoustic signal transmitted through the seal is monitored by a microphone pick-up placed on the opposite side.

Jan 1, 1973

By R. E. Peterson

The Bureau of Mines has undertaken beneficiation investigations on samples representing large tonnages of oxidized taconites in order to develop and evaluate applicable technologies for producing iron oxide concentrates from these materials. Information derived from the investigations can be used to expand the domestic iron raw-materials base and to establish the impact these taconite deposits may have on future national iron ore requirements. This report describes a process that includes reduction roasting, magnetic separation, and flotation, applied to a western Mesabi Range sample taken near Coleraine, Minn. The sample contained 36.8 pct iron and 46.0 pct silica, and represented 0.5 to 1 billion tons of crude material. An average of 962 lb/hr of oxidized taconite was roasted with 33 lb/hr of lignite in a 35-foot-long rotary kiln. Pulverized lignite and natural gas maintained the kiln operating temperature at 850° C. The roasted taconite was beneficiated by magnetic separation and cationic flotation in a 900-lb/hr pilot plant and yielded a product analyzing 68.1 pct iron and 4.6 pct silica, and containing 82.4 pct of the iron in the kiln feed.

Jan 1, 1981

By W. E. Lamont

The Bureau of Mines conducted flotation tests on a mixture of barite waste materials from Nevada in which essentially all of the barite values were finer than 20 micrometers. Flotation variables investigated in these tests were the effects of (1) sodium silicate as a pulp dispersant, (2) sodium hydroxide as a pH modifier, (3) increased amounts of sodium cetyl sulfate, (4) conditioning time and (5) solids content during conditioning. The optimum flotation conditions were achieved by adding 2.5 pounds of sodium silicate and 10 pounds of sodium cetyl sulfate per ton of feed and conditioning the pulp for 20 minutes at a 35-percent solids content. Using these conditions, a concentrate was produced that contained 94.7 percent BaS04, with an attendant recovery of 90.9 percent of the barite in the feed. In addition to the flotation tests, a selective barite flocculation process was developed to treat extremely fine barite. A barite concentrate containing 96.5 percent BaS04 with an attendant recovery of 82.1 percent of the barite was produced by selective flocculation. A process patent application has been filed based on this process.

Jan 1, 1982

Reduce the number of conveyor-related accidents in the mining industry by providing recommendations for effective operation of conveyor belt cleaning systems. The Problem Troughed belt conveyors provide effective, and efficient materials transport and their use has increased throughout the mining industry. Carryback, the spillage that accumulates under the belt, is a problem even with belt cleaning systems installed. Mining personnel are exposed to safety and health hazard; as they attempt to clean up this spillage. Approach To investigate the influence of metal-segmented-blade belt cleaners on the amount of carryback spillage, the. Bureau identified and tested the following parameters: (1) amount of pressure applied to the cleaner blades, (2) friction between the blades and conveyor belt, and (3) wear rates of different metal blades. The test parameters were quantified by recording the amount of carryback material passing the metal cleaner blade, and the weight loss of the blades. The data collected were used to identify the following critic d operational parameters of a segmented-blade conveyor cleaner system: (1) the existence of an optimal operating pressure for the conveyor and cleaning systems and (2) elimination of recessed patterns on the working side of the conveyor belt.

Jan 1, 1989

This chapter details the perspective from which collected data have been examined. The first part, intended primarily for lay readers, discusses several topics related to mining as an enterprise. Initially, the organizational functioning of atypical large mine will be described. It is the formal structure above a miner that decides the conditions of his or her work. A second point of concern is the technology itself An underground coal mine is a sociotechnical system, with workers and machines organized in particular ways during production. Third, general conditions and dangers underground will be described in detail. The physical environment of an operation is a powerful factor in the work life of miners. Fourth, a discussion of the process of formal training is given. During this training, a new worker is taught what the organization expects of him or her in the role of safe, productive, coal miner. Next, there are outside organizations that act as significant forces in the workplace. Examples include the Mine Safety and Health Administration (MSHA), State agencies, and the United Mine Workers of America (UMWA). The roles of these entities will also be examined. The second part of this chapter will depict each study site as a concrete setting, so that findings can be interpreted in their proper context. The Organizational and Technical Nature of Mining A coal mine is a complex system. It is defined as all parts of a mining plant's property (both underground and surface) that contribute, under one management, to the extraction or handling of coal [American Geological Institute 1997]. As suggested, many functions that must be carried out at an operation are only indirectly related to coal mining and processing. Even the jobs that are di¬rectly related tend to be numerous and varied [Wallwork 1981]. According to Palowitch [1982], the chief reason for this sophistication is that "after more than two centuries of exploiting our coal resources, today's coal industry finds itself saddled with a horrendous legacy of human impairments and environmental damages which society demands be corrected." Now, the effects of government regulation are evident in every aspect of the mining industry. Any operation, if it is to survive, must be administered with an eye for social efficiency and accountability. Long-range planning is needed to ensure that the mine produces coal in a cost-effective manner. One of the first things that must be considered is location and method of access. To extract coal from an underground mine, a coalbed (or "seam") must be reached from the surface. The term "portal" is generally given to any entrance that provides access to a coal mine. In hilly terrain, such as is found in Appalachia, the coal may "outcrop" on a hillside. This allows direct

Jan 1, 2000

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of Al-Ni alloys con¬taining 0.54 to 30.04 atomic percent nickel with the aid of the high-temperature galvanic cell Al(1) // Al+3 (AlCl3 in NaCI.KC1) // Al-Ni alloy (1 or s). Activities of aluminum and nickel (compared with pure liquid metals as the standard state) show pronounced negative deviation from Raoult's law at 1,273 K. The properties [?G, ?Gxs, ?G ideal, ?GA1, AGxs1, ?Gni , and ?GNixs] have been derived from the experimental data and are summarized in tables and illustrations. At 1,127 K, the thermodynamic stability for the invariant three-phase equilibrium consisting of a saturated liquid, A13Ni, and A13Ni2 has been uniquely defined by an activity for aluminum of 0.751. A free energy of formation at 1,127 K of -7,940 cal/g-atom was derived for the compound A13Ni.

Jan 1, 1975

By William J. Campbell

The Federal Bureau of Mines provided five test materials--amosite, short-and long-fiber chrysotile, crocidolite, and nonfibrous tremo1ite--to the National Institute of Environmental Health Sciences (NIEHS) for studies on the biological effects of orally ingested asbestos-related materials. An inter-agency agreement between the Bureau and NIEHS made possible this program to characterize these test materials. The Bureau in turn received support through contracts with the Ontario Research Foundation for the milling of amosite and crocidolite, and with the University of Maryland for microscopic measurements. The five test materials, which were supplied in quantities of 960 to 1,200 pounds each, were characterized by chemical-instrumental analysis for elemental composition, surface area, density, X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, mineralogy, and particle size analyses. Particle size distributions were emphasized because of the current theories relating adverse biological effects to length-width characteristics of durable elongated particles.

Jan 1, 1980

By H. A. Doerner

Tellurium is a silver white solid with metallic luster, the e17atal.line torm being ver., brittle aud e.g,s!ly powdered. It has a specific gravity of 6,27, melta at 45a0c. and boils at red het, giving off a. golden 1ellow vapor when air 11 excludei. When heated in air, telluri'UiD burns with a bl\te name tinged with green, and evolves wh1 te vapors ot tellurium dioxide. An amorphous form of tel­lurium, obtained by red.uction and precipi ta.tion from so).ution, haa II specific gr1.vity ot 6,015, and when heated ia cho.nged to the cry:.,talline variety. Telluri,a 11 insoluble in water, c&rbon diaiJ.phido, or h;rd.rochl oric acids, but it 11 41a-1olved bJ nitric or concen t1·ated. sulphi.U·ic acid. It 1..oea not tamiah in moiet ah•• 11 ree11tant to alkaline solutions, e,;:ctpt concentrated KOB, but it 11 cliaaolvecl by tuaed. &lkl 1••. I ts 11.to!!lic weight h..'l.a been the "J.Ubject ot mch controverq, bu\ t.he value 137 .5 :.a bl!ten generally accepted, Tho chflmietr:, of tellurium ia eim1lar to that ot IUlphur. It tonne throo xid.ee TeO, To02, and Te0 , al10 tellur14ea, t•llurite,, and. tellur1.t11, A number of halide compoWld.1, a 3iulph1de, and. a .ulpbat.e are known.

Aug 1, 1922

By M. L. Fenger, S. F. Mauser

This 1s a report on an Investigation performed during Contract No. H0166069 "High and Medium Voltage Trailing Cable Splices and Connections," which presents a summary of the requirements formulated. The requirements are presented in the form of considerations for medium-voltage splices, and medium- and high-voltage couplers used in underground coal mines.

Jan 1, 1979

By L. C. IlsLey

A preliminary investigation has recently been made by the U. S. Bureau of Mines to determine whether or not the ordinary mine- type telephone is entirely safe in gaseous atmospheres . Two well known makes of mine- type phones were purchased for this investigation . It is not conceivable that the current necessary for talking over telephones could ignite gas . However , such phones are provided with efficient magnetos , and it was believed that danger might result from the ringing of the magneto . Again , while this type of phone has been designed to have a certain measure of dust and moisture tightness , evidently it has not been designed as an explosion- proof device . either with regard to cover joints and fastenings or strength of castings . Therefore , the problem was simplified . First it was assumed that owing to the construction of the telephones the gas would penetrate into their interior , and the question was to ascertain whether or not the gas would be ignited from the operation of the magneto .

Jan 1, 1922

By Kenneth L. Rubow, Virgil A. Marple

"INTRODUCTION Respirable dust is defined as the dust which penetrates to the alveolated regions of the lungs. Due to the size selective nature of the particle removal mechanisms in the nasal passages and lung airways, criteria defining respirable particles must be a function of the particle size. Three criteria defining respirable particle penetration are shown in Figure 1. These criteria have been defined by the British Medical Research Council (BMRC), the American Conference of Governmental Industrial Hygienists (ACGIH) and German TBF 50-11 (1).The quantity of respirable particles in an aerosol can be measured by use of two-stage samplers. The first stage consists of a particle preclassifier with penetration characteristics corresponding to one of the respirable penetration curves in Figure 1. The large nonrespirable dust particles are removed from the airstream in the preclassifier and the smaller respirable dust particles pass on to some device which can measure their concentration (the respirable dust concentration).Instrumentation for the measurement of respirable coal mine dust has been limited by the severe conditions existing within the coal mine. The conditions of particular importance are the methane atmosphere, high humidity, and the general non-laboratory type environment. The most severe of these conditions is the methane atmosphere since any electronic or electric powered instrumentation must be intrinsically safe to operate in such an atmosphere.In spite of the difficulty of sampling respirable dust within the mines, many instruments have been developed for in mine use. Although these instruments operate under a variety of principles they generally fall within two categories: personal samplers and area samplers.A personal sampler is worn by the mines while he is performing his duties in the mine. These devices are generally small, light weight and require little power so as not to interfere with the miner's ability to work."

Jan 1, 1988

By Robert J. Willard

This chapter includes tables for 1982 that were not available in time for publication of the 1982 Minerals Yearbook, but does not include corresponding tables for 1983. The value of raw nonfuel minerals produced in the United States during 1988 was estimated at $21.1 billion, an increase of $1.5 billion over the value for 1982. This is a reversal of last year's downturn in value from that of 1981, which was the only decrease noted since 1971; hence, an overall trend of increasing values has been maintained for 12 years, except for 1982. Although the reversal is a basis for cautious economic optimism, it is tempered by continued problems in the domestic mining industry: inadequate funds for capital investment and competition with other countries that have lower production costs. Output of metal commodities in 1983 increased for 8 out of 21 metals, and metal values, in general, increased for 9 of the metals. Output of nonmetal commodities was mixed, with 24 nonmetals showing increases, 20 showing decreases, and 2 unchanged. Nonmetal values were also mixed in 1982: 25 showed increases, 20 declined, and 1 was unchanged. Improvements in the international metals market have not been forthcoming because of the continued depressed prices for major metals. Governments in foreign producing countries have been concerned with maintaining employment and continuing foreign exchange flows through mineral exports. Consequently, the excess of supply in the face of shrinking demand brought downward pressure on metal prices in general, except for the precious metals. On the domestic front, this situation means U.S. mining companies must become even more cost efficient. The major trend in the mining industry in 1983 was to cut costs further, reduce or stabilize total production, reduce outlays for major capital equipment, modify existing systems and equipment, and streamline operations. Most of the accomplishments reported herein reflect this trend.

Jan 1, 1984

By Seth C. Schaefer

The Bureau of Mines has determined the standard Gibbs energies (AGf°) of CoS1.035 (cobalt sulfide) and Ni2.515S2 (nickel sulfide) with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, CoS1.035, CoO, S02(g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt, with the overall cell reaction C0S1.035(c) + 1.535 02(g, 0.0114 atm) = CoO(c) + 1.035 S02(g)¬ These results, combined with the best available data for ?Gf° of CoO and S02 from the literature, give the standard Gibbs energy of formation of CoS1.035 for the reaction Co(c) + 0 5175 S2(g) = CoS1.035(c) ?Gf° = -38.890 + 18.87 x 10-3T ± 0.185 kcal/mole (866.0 - 1,104.9 K), where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, N12.515S2, NiO, S02(g, 1 atm)//Zr02//02(g, 0.0122 atm), Pt, with the overall cell reaction Ni2.515S2(c) + 3.2575 02(g, 0.0122 atm) = 2.515 NiO(c) + 2 S02(g). Combination of these results with data for ?Gfo of NiO and S02 from the literature yields the standard Gibbs energy of formation of Ni2.515S2 for the reaction 2.515 Ni(c) + S2(g) = Ni2.S1SS2(c) ?Gf° -65.377 + 24.67 x 10-3T ± 0.541 kcal/mole (968.6 -1,053.7 K).

Jan 1, 1981

By J. T. McCartney

Thin sections of coal have been prepared for many years either by cutting on a microtome (1,2)5 or by grinding and polishing (2,1). Specimens of most coals had to be demineralized in hydrofluoric acid and softened in caustic solutions before they could be successfully cut with a conventional microtome. Some lignites could be cut without pretreatment. Jeffrey (1) obtained sections from coals of all ranks, although long and tedious pretreatment was required for anthracite. His sections were less than 1 cm.2 in area (probably much less for high rank coals) and about 5 microns thick. Thiessen (2) also cut sections of softened coals, mostly of low rank. His sections were a few square millimeters in area and about 3 microns thick. However, Thiessen preferred ground and polished sections for detailed studies because they were larger and had not been chemically attacked by softening media. He prepared ground sections as large as 4 cm.2 in area and usually 5 to 10 microns thick. Thousands of such sections, covering complete column samples of many coal beds, were studied for a number of years (4). With the development of the electron microscope and increased interest in quantitative optical studies of coals, a need for much thinner sections arose. However, no suitable technique for preparing such sections was known until Fernández-Morán developed a diamond knife for cutting ultrathin sections of hard materials (5). Workers at the Centre d'Etudes et Recherches de Charbonnages de France applied this new tool to the cutting of coal sections and have recently described their technique to the Burg, of Mines. Using their methods, with some modifications, researchers of the Bureau of Mines have succeeded in cutting ultrathin sections of coals ranging in rank from lignite to

Jan 1, 1961

By Roy H. Grau, John C. LaScola

"This Bureau of Mines report contains a tabulation of methane emissions during 1980 for all coal mines located in the United States with emissions greater than 0.1 MMcfd. Listed for each mine are methane emission quantity, location, and coalbed. The report also compares records of 1975 and 1980 and describes relationships between emissions in 1980 and the Bureau's coalbed gas content data on 11 mines.INTRODUCTIONMethane gas is a threat to safety in underground coal mines. Research by Government and industry has led to great gains in reducing methane gas ignitions and explosions. The development of advanced methane control techniques is necessary for the safe operation of more gassy mines and the implementation of rapid mining techniques.As part of this research, the Bureau of Mines has surveyed total methane emission data from underground bituminous coal mines in the United States and tabulated emissions from mines producing over 0.1 MMcfd of methane. This report is an update of similar studies previously described in Information Circulars 8733, 8659, and 8558 (2-4).3The data from 1980 were compiled from Mine Safety and Health Administration (MSHA) records of air quality-quantity inspections made quarterly at each mine. The inspections involve measuring airflow and collecting air samples in the main returns. From these data, an average methane emission is calculated and used to represent the daily mine emission for each quarter. The methane emissions given in this report are the averages of the four 1980 quarters and do not include mine emissions from other sources such as degasification projects. Since a previous Bureau study showed that emissions from mines emitting less than 0.1 MMcfd represented only 2 pct of all emissions, 0.1 MMcfd was chosen as a lower limit for data collection (4)."

Jan 1, 1982

By R. Karl Zipf

MULSIM/NL (multiple scams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines and thin metalliferous veins. It can analyze one to four parallel seams that can have any orientation with respect to the Earth's surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) nonlinear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. Detailed checks show that numerical stress and displacement calculations compare well to known analytic solutions for simple problems. The total energy release calculated by MULSIM/NL is comprised of three basic terms: (1) strain energy release from the mined-out material, (2) linear kinetic energy release due to change in gravitational potential over the mined-out area, and (3) nonlinear kinetic energy release due to nonlinear materials in the total backfill and gob area. The strain energy release term is modified to account for nonlinear stress-strain behavior in the unmined materials. Comparisons of these numerical energy release rate calculations with known analytic solutions show excellent agreement.

Jan 1, 1992

By Thomas V. Falkie, R. Venkataramani

1. Summary This investigation is concerned with description of the loading function at the underground coal face, and the identification of varia¬bles - geological, geometric, mechanical, and operational - that affect the loading function. The immediate objective of this work was to provide information for operations-research studies as applied to underground coal mining, and the broad objective was to provide guide¬lines for planning and equipment selection in underground coal mining. The loading function was expressed as -a statistically-developed linear mathematical model. Originally, fifteen independent variables were considered which potentially could have influenced the loading function. These variables were constructed on the basis of measurable or estima¬ble geometric and geological properties at the working face, mechanical characteristics of the mining machine, and certain operational proce¬dures of mining. The original model explained 64.0 percent of the experimental variation. The final condensed model explained 54.1 percent of the experimental variation in terms of only five indepen¬dent variables, namely: 1. Ratio: width of cut/total width of cutter 2. Ratio: height of cut/diameter of cutter 3. Total horsepower of cutter-drive motors 4. Rotation speed (RPM) of cutter 5,. A subjective estimate of machine quality and operator skill Certain limitations were found to exist in the evaluation of the variables. Principle among these limitations was the impossibility of precise measurement of tonnage loaded in certain instances.

Jan 1, 1972

By C. I. Pierce

The Bureau of Mines conducted laboratory tests to determine if ultrasonic energy could reduce either the residual water or oil content of petroleum reservoir-rock samples from Appalachian area oilfields. Brine-saturated core samples were flooded with oil to residual brine saturation and subjected to 20 kilocycles per second ultrasonic energy. Then they were flooded with brine to residual oil saturation and again subjected to ultrasonic energy. Additional water displaced as a result of the application of ultrasonic energy to the flow system ranged from 0 to 4.3 percent of the original brine and averaged 1.9 percent. The increase in oil recovery as a result of the ultrasonic energy ranged from 0 to 9.0 percent of the original oil and averaged 3.1 percent. On the basis of the tests, it appears that 20-kcps acoustic waves would not have field application for oil recovery.

Jan 1, 1968