Search Documents

By R. L. Grayson, S. S. Peng

"Research has been conducted during the past year on a study to correlate respirable coal mine dust characteristics with worker positions and coal seams. The first characteristic of respirable coal mine dust which has been addressed in the correlation study is respirable dust mass concentration. In fulfillment of this objective, two mines operating in different coal seams have been selected for respirable dust mass sampling on both longwall panels and continuous mining sections. At present, sampling has been completed on the longwall panel operating in the first mine, and one half of the planned sampling has been accomplished on the continuous mining section.The first mine sampled is operating in the Pittsburgh coal seam. The average mining height is approximately 78"" with an average of 8"" of bottom shale being mined. The mine is primarily a longwall mine, and continuous mining machines are used to support the longwall.Figure 1 shows the layout of the longwall panel which was sampled. Intake air is coursed via the track heading up to the headgate area. The air splits at the headgate. Approximately 20,000-30,000 cubic feet of air per minute (CFM) is used to ventilate the longwall face and about 5,000-10,000 CFM is routed down the belt entry. Substantial leakage across the gob was noted during the sampling period. An average of 1800 CFM per 100 feet of face leaked through the shields into the gob from #1 shield to #112 shield. A substantial amount of leakage also occurred between the #1 shield and the solid rib of the headgate development panel. The path of the air used to ventilate the panel is shown with arrows in Figure 1. Direction of air flow was opposite to the coal moving direction on the armored face conveyor.A double-drum ranging shearer is used on the face to cut a 30-inch web of coal. Normal practice is to cut from the tailgate to headgate with the leading drum raised and the tail drum lowered for cutting bottom. After reaching the headgate, the shearer is reversed and both drums are lowered for a clean-up pass. The last 40 feet of face on the tailgate is cut on the clean-up pass.The shearer is equipped with 2 banks of 4 water sprays each and 2 large sprays on the headgate end and 1 bank of 4 sprays on the tailgate end. Additionally, sprays are located above bits on the cutting drums. Actual cutting speed was approximately 14-18 feet per minute, depending on conditions.The cross sectional area for air flow on the face was approximately 60 square feet before a pass was mined and 80 square feet after a pass was mined but before the shields were advanced. The cross sectional area at the shearer was about 35 square feet.The condition of both the tailgate and headgate of the panel was good with no signs of significant roof problems. The roof conditions along the face during the sampling period were variable. At times, as much as 3 feet of drawslate fell from the roof for a span of as much as 40 shields. Generally, however, relatively local areas of falling roof were encoun-tered, usually limited to a 10-20 shield span when appearing.Ten days were spent gathering respirable dust samples on the longwall panel. Mine Safety Appliance (MSA) sampling units equipped with 10-mm nylon cyclones, pre-weighed MSA PVC filters, and constant-flow DuPont pumps were used to obtain thesamples. The pumps were calibrated at a 2 liters-per-minute flow rate. The 10-mm cyclone was selected for classifying total dust into the desired respirable fraction in order to obtain ""legally defined"" respirable dust samples for detailed physical characterization."

Jan 1, 1988

By H. W. Kilau

The U.S. Bureau of Mines examined the wettability of bituminous and subbituminous coals before and after exposure to ambient air atmosphere, as part of an ongoing project investigating the coal-wetting abilities of surfactant solutions intended for the suppression of dust during coal mining operations. Exposure periods were generally 7 days or less, and the changes in wetting response were measured with a capillary penetration apparatus. Wetting solutions tested included a nonionic surfactant, two anionic surfactants, and pure distilled water. After exposure, higher ranked bituminous coals treated with nonionic surfactant solution and pure water showed increased wettability, but lower ranked subbituminous coals showed decreased wettability. With the anionic surfactants, the coals demonstrated opposite responses. The wettability changes appeared to be related to the coal moisture content. These changes may be amplified by specific, but incompletely understood, interactions between surfactant polar groups, absorbed water, and the coal surface.

Jan 1, 1989

By Donald P. Blasko

The first well that produced commercial quantities of oil in the Cook Inlet Basin of Alaska was completed in 1957. Since that time oil production in the basin has increased rapidly and by the end of 1969 had reached an annual rate of 74 million barrels. Five major oilfields had been developed, and two additional discoveries awaited development. Estimated amounts of recoverable oil by primary and secondary recovery methods total 2.7 billion barrels, or 36 percent of the estimated oil originally in place. Repressurization by injecting gas or water in formations containing undersaturated oil has significantly increased the volume of recoverable oil. All production has been from formations of the Tertiary age; that much of it is from depths of 10,000 feet or more is unusual for Tertiary formations. The oils are low in sulfur and contain low to moderate amounts of asphalt.

Jan 1, 1972

By R. S. James, E. J. Gleim

Not long after electrically driven equipment was introduced into coal mines it became apparent that the spark-producing parts, such as controllers and motors, required safeguards to prevent the ignition of mine gas that might come into their vicinity. Many of the early designs attempted to provide protective enclosures having ventila¬tion and relief for pressures if ignition should occur within. The principal feature of the Davy safety lamp, namely, the wire gauze, was employed widely for this purpose. Other devices were developed to reduce the temperature of products of combustion escaping through the protected openings to a value below that which would cause ignition of surrounding explosive atmospheres. Although many such devices performed their intended function satisfactorily under laboratory conditions they were not so satisfac¬tory when subjected to the rigorous conditions encountered under¬ground. Corrosion, mishandling, and accumulations of grease and dirt reduced or destroyed their protective qualities after a period of service in the mines. In the United States this has led to abandon¬ment of special devices in favor of what is called " total enclosure " which means that no regular provision is made for ventilation and release of pressure but rather that the housings or enclosures are built strong enough to withstand the explosion pressures without rupture. As a further protection the joints usually are made of broad, closely fitting surfaces. It is impractical to make such joints absolutely gastight in ordinary machine practice when provision must be made for partial or complete disassembly to facilitate ad¬justments and repairs. Therefore, when an explosion occurs within such enclosures flames may escape through the joints. If the latter are broad enough and not separated too widely, however, the flames will be cooled by contact with the metal surfaces (flanges) of the joints, by rapid expansion, or by both cooling and expansion, with the result that an explosive atmosphere surrounding the enclosure will not be ignited. This is termed " flange protection." In testing parts of cutting machines and other equipment for coal mines, with the ultimate object of approving the equipment for use

Jan 1, 1935

By M. Hertzberg

This Bureau of Mines report proposes a new methodology for estimating industrial dust explosion hazards in terms of three probabilities or co-factors: The dispersion of the dust, the existence of a flammable dust concentration, and the presence of an effective source of ignition. This method or rationale is proposed as a replacement for the "explosibility index" that was first suggested 25 yr ago, but which, by consen-sus among leading researchers in the field, is now outdated. This report presents a detailed critique of the deficiencies of that old, material-oriented index, and develops the logical rationale for its re-placement by an approach that is better suited for quantitative hazard evaluations. A variety of such evaluations are illustrated, which show how a quantitative prediction of explosion frequencies can be obtained from laboratory measurements and operating conditions in a given indus-trial facility. The method has some pitfalls, particularly as they re-late to the correlation of events or their randomness. These are discussed, as well as the method's other limitations and uncertainties. This work is intended to provide a beginning to a quantitative approach to explosion hazard assessment. To that end, a new method is proposed for estimating thermal ignition probabilities in terms of the measured laboratory autoignition temperature of a dust, its relationship to the operating temperature, and its distribution within a given industrial system.

Jan 1, 1987

By R. E. Head, Virgil Miller

"INTRODUCTIONRecent investigations at the Intermountain Experiment Station of the Bureau of Mines at Salt Lake City indicate that metallurgists have given little attention to the occurrence of jarosite minerals in the oxidized ores of lead and silver. These investigations have also emphasized the importance of knowing when these minerals occur in the oxidized ores, especially those containing lead, silver, and gold, as their presence is a material factor in selecting a suitable kind of treatment. Since the question of the occurrence of jarosites in oxidized ores has come to the attention of the Bureau of Mines, investigation has indicated that plumbojarosite and argentojarosite are quite common. These two minerals appear to be widely distributed and probably escaped recognition by persons who had attempted to treat certain oxidized lead ores in which the jarosite minerals represented a material portion of the metal content.Consideration of the physical characteristics of the jarosites also indicates that in many cases failure to treat some of the oxidized lead ores with success has been directly due to the fact that the greater portion of their lead and silver content was present as plumbojarosite and argentojarosite. The data and the description of these minerals given in the body of this paper indi¬cate that attempts to recover lead and silver from ores in which appreciable amounts of the metals occur as plumbojarosite and argentojaeosite would be unsuccessful if confined to gravity methods of concentration. There are un-doubtedly considerable tonnages of oxidized lead ores in the various mining regions of this and other countries, and it is quite probable that in some of these ores the metal content of lead and silver may be largely anglesite (lead sulphate) and cerussite (lead carbonate) but that they will also contain cerargyrite (silver chloride), argentojarosite, and plumbojarosite. The treatment of such ores therefore presents an important problem, since a product is discarded from ores from which the recoveries of lead and silver have been below 70 per cent which is probably too low-grade to warrant aftertreatment by any process now in use."

Apr 1, 1928

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

By J. H. Field

Capital and operating costs have been estimated for removing sulfur dioxide from flue gases of a powerplant of 12,000-kw. capacity by liquid-purification processes, using limestone, ammonia, or sodium sulfite as the reactant. The annnonia and sodium sulfite processes yield end products that may be marketable. Coals containing about 1.5 and 5.0 percent sulfure have been considered. The sulfur dioxide content of the gases to be treated is 0.083 and 0.30 percent, respectively. Estimates have been made for 90-percent removal of the sulfur dioxide from both gases. A third instance has been considered in which 70 percent of the sulfur dioxide is removed from the flue gas of 0.30-percent concentration. The scrubbed gas would contain 0.09 percent sulfur dioxide, which might be within the permissible limit for discharge to the atmosphere in most areas. Although it is unlikely that flue gases with sulfur dioxide concentrations of less than 0.10 percent would require purification, a cost estimate for such a gas is included because an estimate is available for a British plant employing the limestone process at these conditions. Capital investment and operating costs, with no credit for products, are lowest for the limestone process for gases of both concentrations. Crediting the ammonium sulfate and sulfur produced in the ammonia process at their market prices at the end of 1956 of $32 and $28 per ton, respectively, the operating costs of the ammonia process become the lowest for purification of the gas containing 0.30 percent sulfur dioxide. The operating costs of the sodium sulfite process for purifying gas of high sulfur dioxide content approach those of the limestone process when the byproduct sulfur dioxide is credited at $14 per ton. Even if credit for products is allowed for the ammonia and sodium sulfite processes, the operating costs are higher than those of the limestone process for the gas of low sulfur dioxide content. Because of the large quantity of materials that would be produced by removing sulfur dioxide from a relatively small number of plants, credit for products should be allowed with extreme caution.

Jan 1, 1959

By Paul W. McGann

THE MINERAL INDUSTRIES had a near-record year in 1950, as rising industrial activity in general, greatly accentuated by the outbreak of hostilities in Korea in midyear, called forth increasing supplies of mineral fuels and raw materials. The aggregate value of mineral production was second only to that in 1948, and the aggregate physical volume was exceeded only in 1948 and 1947. Lower coal production accounted for the failure to surpass these earlier years. Growth of production was fairly constant throughout the year, especially for crude petroleum; its physical output for the year as a whole exceeded that of 1949 by 7 percent. According to Federal Reserve Board indexes, other relative gains were 16 percent for coal, 9 percent for fuels in general, and 17 percent for metals. The increase for mining in general was of the order of 10 percent. This was not quite as large as the general increase in industrial production but clearly reflected the total-industrial trend (see fig. 1).

Jan 1, 1953

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995

By M. J. Reasor, M. DiMatteo, J. M. Antonini, K. Van Dyke, Z. Ye

"The inhalation of silica has been shown to produce a dramatic inflammatory and toxic response within the lungs of humans and laboratory animals. A variety of cellular and biochemical parameters are used to assess the silica-induced lung injury. The purpose of this paper is to introduce the use of luminok:Jependent chemiluminescence as a new method to study inflammation in both phagocytic cells and lung tissue recovered from silicaexposed animals. Chemiluminescence, or the emission of light, accompanies the release of reactive forms of oxygen when phagocytic cells are challenged. In this study, male Fischer 344 rats were intratracheally instilled with either silica (10 mg/100 g bw) or saline vehicle. One day after the instillations. a marked increase in the chemiluminescence was observed in the lung tissue and bronchoalveolar lavage cells recovered from the silica- treated animals when compared with the saline controls. The light reaction was markedly decreased by either superoxide dismutase or N-nitro-Larginine methyl ester hydrochloride. Superoxide dismutase is involved in the enzymatic breakdown of superoxide anion. while N-nitro-L-arginine methyl ester hydrocholoride, a nitric oxide synthase inhibitor, prevents the formation of nitric oxide. When superoxide anion and nitric oxide react. they form the highly oxidizing substance peroxynitrite. This study then implicates peroxynitrite as an agent that may be responsible for some of the oxidant lung injury that is associated with silica exposure. The use of luminol-dependent chemiluminescence may prove valuable as a method to measure the earliest events in the inflammatory process. and may be an adjunct in studying the mechanisms that produce inflammation. - Environ Health Perspect 102(Suppl 10):37-42 (1994) IntroductionResearch on inflammation has not produced a method that links the initial events of the process to the controlling events. Rather, a variety of parameters are measured that are the result of and not the basis of the inflammatory reaction. Parameters such as tissue weight, edema, blood flow, enzyme and protein release, or production of metabolites (prostaglandins, leukotrienes) have been used extensively. A method is needed that could be applied to cells of a particular type, groups of cells of different types, and even tissue, in an attempt to study the kinetics of the inflammation as well as being sensitive enough to monitor the early events of the process . Since inflammation is so complicated, the relationship between the control of the initial events and the oxidation process has never been explained nor studied in any derail."

Dec 1, 1995

By Forrest T. Moyer

In conjunction -with the statistical survey of the lime industr-.r in 1939, by the Bureau of Hines, producing companies reported the lime-fuel ratios attained in their plants according to type of kiln and kind of fuel. Each ratio, expressed as the number of pounds of lime burned by a unit quantity of fuel, was weighted according to the tonnage of quicklime pro- . duced at the reporting plant and grouped with similar data from other plants, so that an average ratio for each type of fuel and,kiln could be calculated. By this method the variables trat affect ratios of individual plants are more or less equalized, and the computed average lime-fuel ratios provide a fair measure of kiln and fuel efficiencies during 1939.

May 1, 1941

By W. E. Young

This paper describes operations of the Chief Consolidated Mining Co. at the Chief mine in the Tintic district, Juab County, Utah, where the outstanding problem is water control; the unique pumping methods employed are featured in this report. The ore bodies in this district occur as long, narrow shoots along fault fissures, usually in the Bluebell dolomite of Ordovician age. Oxide ores predominate above the 1800 level, which is also the natural water level. Sulfide ores containing lead, zinc, silver, and gold extend below the 1800 level. The mine is developed by vertical shafts and winzes, from which drifts are driven to the ore bodies. In the lower levels of the mine these drifts extend long distances from the shafts or winzes because of the relatively low dip of the ore shoots. The mine has been worked to the 2800 level and the 18-411 winze extends to the 3080 level.

Jan 1, 1958

By M. J. Sapko

The Bureau of Mines conducted laboratory-scale flammability experiments to investigate the possible use of water spray systems for inerting or quenching mine-gas ignitions, such as those encountered at the working face of a coal mine. The inerting results for premixed methane-air-water mixtures indicated that water droplets of less than 10 µm tend to be as effective as the vapor. Water requirements for inerting such mixtures were much smaller than those for quenching the sustained flame propagation by the application of water sprays. The minimum water mass concentration for quenching methane-air flames increased linearly with increasing droplet diameter (surface weighted mean) and decreased with increasing spray temperature, whereas the droplet surface area required per unit volume was essentially constant for a given gas mixture composition. Data extrapolations indicated that a quenching system may be feasible for the longwall mining application.

Jan 1, 1977

By Ronald H. Church, Walter E. Pittman, J. T. McLendon

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

By John D. Corrick

Three species of chemosynthetic iron- and sulfur-oxidizing autotrophic bacteria have been isolated from the leaching waters of copper mining areas. These species are: The sulfur-oxidizing Thiobacillus concretivorus, the iron-oxidizing Ferrobacillus ferrooxidans, and a sulfur- and iron-oxidizing bacterium closely resembling Thiobacillus ferrooxidans, INTRODUCTION Among several suggested new processes for treating marginal ores in the United States, none is more intriguing than the possibility of extracting metals from low-grade materials by the action of microorganisms One phase of a Federal Bureau of Mines investigation toward developing such a procedure was to isolate and identify specific chemosynthetic iron and sulfur. oxidizing autotrophic bacteria native to certain domestic copper deposits where leaching is practiced. The bacteria or microorganisms considered important to this investigation are those capable of producing solutions of ferric sulfate and sulfuric acid. Solutions of this type are excellent solvents for some copper minerals By establishing the presence of these bacteria at certain copper-leaching areas, strength would be given to a theory that microbial activity is partly responsible for the oxidation that takes place at these areas. Their presence also advances possibilities for controlled use of microbial action in metal extraction processes. Leathen4/ has demonstrated that one of the chemosynthetic iron-oxidizing bacteria, Ferrobacillus ferrooxidans, can oxidize 200 parts per million of ferrous iron to the ferric state in 3 days,

Jan 1, 1961

By Raymond F. Farrell

A goal of the U.S. Department of the Interior, Bureau of Mines, is the advancement of minerals technology through the development of improved metals and minerals processing. In support of this goal, the Albany Metallurgy Research Center has developed atomic absorption spectrographic methods for the rapid analysis of A1203, CaO, Fe203, MgO, MnO, and Si02 in steelmaking slags. The application of these methods is discussed using an inexpensive pressure dissolution system. The overall coefficient of variation is 5 pct. The accuracy is the same as the reproducibility.

Jan 1, 1979

By Gregory M. Molinda

The U.S. underground coal miner faces a continuing hazard from the fall of roof. At the root of many injuries and fatalities are weak or defective roof strata. Throughout mining history, millions of miles of entry have provided exposure of every conceivable geologic roof hazard. This report describes the geologic origin, association, and potential danger from the most common hazards. Discussions of weak rock include drawrock, rider coals, head coal, stackrock, and stream valley effects. Discontinuities, or roof defects, are described including, clay veins, slickensides, joints, and paleochannels. A number of examples from U.S. coalfields are used to document geologic structure and associated hazards. Roof fall analysis is a methodology used by NIOSH for hazard recognition and prevention; its application and benefit to the industry are discussed.

Jan 10, 2003

By A. Sainato, S. J. Kravits, G. L. Finfinger

This Bureau of Mines report describes and compares the procedures, capital investments, and operating costs of rotary and in-hole motor drilling techniques used to drain methane gas from the Pittsburgh Coal- bed in an underground mine located in southwestern Pennsylvania. A timestudy was conducted during the drilling of each of two boreholes, and the data were collated to serve as a base for comparing drilling procedures and operating costs. Findings indicate that drilling with an in-hole motor offers four advantages over rotary drilling; namely, an increase in drilling productivity, fewer worker-hours required, ease of maintaining vertical and horizontal bit trajectory, and less expensive drilling cost per foot of borehole.

Jan 1, 1985

By E. J. Gleim

The construction of explosion-proof electric mine equipment for operation in gassy coal mines of the United States was begun as early as 1903. In 1.906, similar equipment with special protective devices was built for export. An investigation of explosion-proof motors was conducted by the United States Bureau of Mines during 1910 and 1911. In other words, this was among the first efforts of the Bureau directed toward the saving of life and property subsequent to its establishment by act of Congress in 1910. In these early motors, those with special devices for relief of explosion pressures predominated. At that time it was generally considered that, by providing for pressure relief, the enclosures could be made lighter in weight because of the lower explosion pressures developed within.

Jan 1, 1954