Search Documents

By D. Harrington

Recently the attention of the U. S. Bureau of Mines has in a number of instances been called to the firing of shots of permissible explosives in coal mines with delay-action detonators. In one bituminous coal mine they were used to bring down the coal for conveyor loading; in another in blasting pillars, which were not undercut; in another in one of the two charges separated by stemming in deep drill holes where the coal was undercut and sheared and mechanically loaded; in another in shooting top coal; and in another in the shooting of coal faces electrically from the surface. Some of these mines were rated as gassy by the State Mining Department in the State concerned. In most instances the charging of holes was done while the working shift was in the mine, and in some the shots were blasted while the working shift was in the mine. In all of these cases the shots were dependent - that is, the efficacy of the succeeding shots was dependent - upon the firing of the preceding shot or shots. The first shot, or possibly two or three shots, was usually fired with a no-delay electric detonator or an instantaneous electric detonator.

Jan 1, 1929

By Yael Miron

Two recent unplanned detonations occurred during blasting operations in sulfide-bearing ores in a Nevada gold mine. Other premature detonations have also reportedly occurred at other Nevada, California, and Arizona operations within the past few years, with increasing frequency. Unplanned or premature detonations can be extremely hazardous to life and can cause extensive property damage. A miner was injured in one of these occurrences. This report, by the U.S. Bureau of Mines, is intended to acquaint personnel involved in such mining activities with the basic causes for these accidents. These causes include the exothermic oxidation of pyrite (FeS2) and formation of ferrous sulfate (FeS04), the exothermic and energetic reaction of the ferrous sulfate with ammonium nitrate-fuel oil (ANFO)-based explosives, and the associated elevated temperatures that can set off detonators and explosives in the boreholes. Recommendations for safe operation by the Mine Safety and Health Administration, the Bureau, and the mine involved with the recent incidents include monitoring temperatures in the blast holes, analyzing for sulfate and ferrous ions, and limiting the time between loading and firing in accordance with conditions in the blast holes. Other procedures for safe operations should fit specific conditions in, the mines.

Jan 1, 1992

By T. F. Dumm, L. G. Austin

"INTRODUCTIONGomez and Austin (1,2) have recently described calibration procedures for quantitative chemical analysis of particles by energy dispersive spectroscopy using particles mounted and polished in a resin matrix and scanned by an SEM under computer control. Their software is specifically designed for the analysis of Si, Al, Ca, Na, K, Fe and S in coal particles, and in this case the resin is loaded with iodine (3) to enable the exposed cross-section of an embedded coal particle to be differentiated from the matrix. However, the basic ideas of their procedures could be extended to any system of particles where it is desired to measure inorganic species in particles containing light elements such 0, C, H and N which are not directly detected. In these circumstances it is necessary to perform a quantitative determination of the measured components, so that the equivalent volume of light elements in the excited sample volume can be estimated by difference using ZAF and other corrections applied to the raw count intensities.Part of their procedure involves a new technique (2) for estimating background spectrum intensities; the intensity for a particular energy window is then subtracted from the total measured intensity for that window to enable the concentration of the corresponding element to be calculated. In addition, corrections for overlap of peak spectrums are applied. For example, Figure 1 shows some typical spectrums for known materials for the system they used, demonstrating a wide Gaussian spread about the theoretical peak energy. Since background spectrum and peak overlap corrections require a knowledge of the composition of the material, as does the application of the ZAF corrections, it is necessary to have an iterative solution of the equation sets, starting with estimates of the composition based on initial count rate corrected solely for dead time and detector efficiency."

Jan 1, 1989

By Dupuy. Leon W.

"INTRODUCTION For many generations the Indian tribes of the southwestern deserts knew of the thermal springs of the Coso District in southwestern Inyo County, Calif. Belief in the reputedly healing qualities of the waters and muds of the area was widespread. F. J. Sanders discovered mercury in the siliceous sinter around the hot springs while he was exploiting the district as a health resort. In searching for new domestic sources of supply of strategic minerals, authorized under the Strategic Materials Act, 3/,the Geological Survey 4/ first examined the deposits, which were drilled and sampled by the Bureau of Mines in the spring of 1941.The deposits investigated comprised three units known, respectively, as The Devils Kitchen, Nicol, and Wheeler. Most of the work was done at the first two.Of particular interest in the Bureau's work on the project was the adaptation and use of the bucket drill as a tool for sampling shallow, soft ore deposit."

Mar 1, 1948

By J. O. Winget

Phosphonic acid and iminodiacetic acid chelating resins were investigated to assess their potential as selective ion exchangers for separating lanthanide elements and yttrium . The affinity of phosphonic acid resin for lanthanides increases with increasing atomic number , and that of iminodiacetic acid resin for lanthanides increases with atomic number to a maximum for element 62 and then declines with atomic number throughout the remainder of the series . Elution sequences of the elements with mineral acid eluants corresponded favorably with equilibrium data , whereas the elution sequence obtained with chelating eluants was proportional to the relative values of the stability constants of the chelating agents with the lanthanides . Separation of lanthanide mixtures into groups of light and heavy elements with iminodiacetic acid resin appears feasible .

Jan 1, 1964

By W. Beckering

In characterizing tars obtained by the low-temperature carbonization of North Dakota lignite, infrared spectra have been an invaluable aid in both qualitative and quantitative examination. Quite, early in the tar-research program of the Federal Bureau of Mines it became evident that the small number of published spectra available for hydroxy-aromatics would be inadequate for comparative purposes when dealing with the wide range of compounds present in coal tar; therefore, compiling a catalog of spectra was begun as a continuing part of the tar program. Because these spectra should be valuable to other investigators in this and related fields, they are being presented in these reports. This supplement to the original publications presents the spectra (figs, I to 32), representing 32 compounds, largely phenolic materials. The major problem of this project has been the availability of materials for examination. Most of the compounds included in this supplement were synthesized at the Bureau of Mines Lignite Research Laboratory. Some were obtained from commercial sources, whereas the compound 2'-hydroxy-l-phenylnaphthalene was synthesized at the Bureau of Mines laboratory in Bruceton, Pa. The spectrum of 2-ethyl-4-methylphenol, figure 32, is a correction of the spectrum presented as figure 26 in the original reports

Jan 1, 1961

By Richard D. Miller

This publication contains routine analyses and related source data for 350 natural gas samples from 19 States collected during calendar year 1962 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Helium Activity of the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus. Four previous publications have been made to present the results of 5,648 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1962. The first, Bulletin 486, 3/ contains analyses and data on 2,195 gas samples collected during the period 1917-47. Bulletin 576, 4/ the second publication, includes data and analyses for 1,575 samples collected from 1947 through May 1956. The third bulletin 5/ contains 1,444 analyses and source data of samples obtained from May 1956 to January 1, 1961.

Jan 1, 1964

By Charles A. Kumke

In June 1942 , ' the Bureau of Mines selected the Zonia copper mine , near Kirkland , Yavapai County , Arizona , as a property meriting investigation in connection with its search for supplies of strategic minerals for use in the war . The following month , representatives of the War Production . Board conferred with Bureau officials and requested that the property be explored with the object of determining the tonnage and grade of ore that could be brought into production quickly and mined cheaply by open-pit methods . The work wa's designed to verify information submitted by the owners in support of an application for a Government loan. It was essential that the investigations be completed promptly , so that operations might be planned and copper produced for war needs . The investigations called for surface trenching , diamond drilling , and check sampling of underground workings . Unable to purchase equipment for trenching without considerable delay , the Bureau saved time by borrowing most of the necessary items from the Golden Queen mine of the Gold Fields Development Co. at Mohave , Calif. This company , whose engineers had sampled some of the old trenches , had a tentative agreement with the owners to operate and manage the Zonia mine in event the loan was granted . Additional equipment was borrowed from two Governmental agencies . The exploratory work , completed in 16 weeks , was carried on 7 days a week .

Mar 1, 1947

By Raymond M. Stateham

Calculations based on data obtained from measurements of smoke from coal-fired powerplants predict that infrared imagers will be useful tools for smoke vision. Infrared imagers operating in the 3-to 5-um spectral region have been evaluated for this purpose. A mine opening 110 meters long was filled with smoke from burning coal, and two men, wearing breathing apparatuses, moved through the smoke to serve as targets. The men were detected and identified at 80 meters.

Jan 1, 1976

By James L. Eirls

The objective of this project was to improve a driver's field of view for large trucks used in the mining industry. Rearward viewing was enhanced by improving the rear-view mirror designs. Rear vision was accomplished using a closed circuit television system. Views ahead,, to the right, and downward were obtained with a blind area viewer (BAV). The BAV is a unique combination of fresnel lenses housed in a shielded, environmentally protected enclosure that produces an image of the area in front of and downward 70° and to either side of the BAV 300. The improved visibility devices were evaluated by long-term, in-mine testing. The right Bide mirror (RSM) and BAV provide the greatest improvements for the least cost and are commercially available. Application of the RSM and BAV should achieve a reduction in accident potential and greater vehicle productivity by enlarging and improving the equipment operator's visibility and making priviously blind areas and hazardous situations detectable.

Jan 1, 1982

By R. Karl Zipf

A fatal explosion in a sealed area at the Sago Mine in 2006 prompted researchers and regulators in the United States to re-examine the requirements for explosion-resistant mine seals. Seals are used in underground coal mines to isolate abandoned mining areas from active workings. Prior to the Sago disaster, mining regulations required seals to withstand a 140 kPa explosion pressure. Recent research at the National Institute for Occupational Safety and Health (NIOSH)Pittsburgh Research Laboratory showed that pressures from explosions can far exceed this pressure. U.S. mining regulations now require much stronger seals. Current research focuses on understanding the science, engineering and management of sealed areas of coal mines. Scientific efforts seek understanding of how explosive methane-air mixtures accumulate using measurements and models of the sealed area atmosphere. Additional scientific efforts aim to understand the explosion pressures that can develop using a combination of numerical modeling and experiments. Engineering efforts aim to produce design guidelines for seals that can resist the new higher pressure design criteria. NIOSH researchers are also developing guidance for monitoring of sealed area atmospheres and inertization of potentially explosive gas mixtures within sealed areas. This paper seeks to encourage scientific discussion among international peers since preventing explosions within sealed areas is of interest to underground coal operators and regulators.

Jan 1, 2009

By H. E. Powell, T. E. Hill, W. A. Calhoun

The object of this investigation was to determine the effectiveness of certain cationic flotation collectors , Ethomeens , in recovering fine particles of lead minerals from mill tailings at a grade equal , at least , to that of the mill feed ( 1.7 percent lead ) . The Ethomeens , derived from tertiary amines having one fatty alkyl group and two polyoxyethylene groups attached to the nitrogen , were evaluated by bench- scale flotation tests . The 14 Ethomeens tested consisted of four groups : Coco amine , soybean amine , tallow amine , and stearyl amine . The best results were obtained with coco amine C / 12 , soybean amine S/ 15 , tallow amine T / 12 , and stearyl amine 18/20 . From a feed containing 0.23 percent lead , rougher concentrate grades of 2.12 to 3.89 percent lead were obtained , with recoveries of 17.3 to 27.5 percent of the total lead . Some of the lead mineral particles recovered had diameters of less than 1 micron . In comparative tests , the Ethomeens , or polyethoxylated amine types of cationic surface active agents , were more selective than conventional xanthate collectors for flotation of slimed lead minerals .

Jan 1, 1964

By Floyd G. Anderson

Owing to the rapid growth of the perlite industry in recent years, the Bureau of Mines has received numerous requests for information relative to the possible harmful effects of breathing dust resulting from the processing and use of perlite. As published information on the composition of perlite is rather meager, consisting chiefly of conventional chemical analyses, samples of crude and expanded perlite from 9 deposits in 6 Western States were studied. Crude perlite ores were examined petrographically and analyzed by chemical, spectrographic, and X-ray-diffraction methods. Sized crude and expanded perlites were analyzed chemically for total free and combined silica content.

Jan 1, 1956

By G. H. West, R. L. Sebastian, W. A. Darror

"This bibliography was compiled in the course of research work by the Bureau of Mines on the utilization of magnesites in the West. The results of the research will appear as a bulletin of the Bureau.1. ANALYTICAL METHODS. 11 Knight, X. and Wheeler, W.H. Proc. Iowa Acad. Sci., 13, 1907, 167 (C.A.1, 1370). Describes experience in analysing calcite and dolomite. Reports great excess of oxalate unnecessary and separation of sulphates by alcohol is best.2 Meyerhofer, J. Zeit, Angew. Chem., 21, 1908, 592. Direct determination of Mg as phosphate after removal of SiC2, by keeping R203 in solution with ammonium citrate.3 Merckschen Guano Phosphat Werke. Chem. Ztg., 33, 1909, 545 (C.A. 3, 2281). volumetric analytical methods.4 Popel, M. Zeit. Angew. Chem., 21, 1908. 2082 (C.A, 6, 412). Determination of CaO in presence of CaC03.5 Blasdale, W.C. Jour. Am. Chem. Soc., 31, 1909, 91? (C.A. 3, 2658). Studies of separation of Ca from Mg.6 Hundeshrgen, F. Zeit. Offent. Chem., 15, 1909, 85 (C.A. 3, 1853). Valua¬tion of caustic magnesia by analysis. Volumetric methods.7 Frerichs, H. and Krosberg, W. Apoth. Zeit., 24, 1909. 679 (C.A. 3, 2996). Tecting magnesia alba for Fe.8 Schoorl, N. Zeit. Anal, Chem., 48, 1009, 593 (C.A. 4, 5E9). Microchemical tests for Mg, Li, K. and Na.9 Heyer. Chew. 2Ag., 33, 1009, 1157 (C.A. 4, 1588). Determination of CaO in presence of CaCO3. CaCO3 in soluble in cold neutral solution of NH3 salts. Solubility Is diminished by free NH4OH."

Oct 1, 1923

By W. R. Moorehead

This paper, describing the mining methods and colt at the New Indria quicksilver mine, is one of a series of similar papers being prepared by the Bureau of Mines on various mines in the United States. The New Idria mine lies at an elevation of 3,500 to 4,200 feet in the Coast Range of San Benito County, Calif. The property is accessible by automobile stages from Gilroy or Hollister via Tres Pinos. Tres Pinos, 65 miles northwest of the mine, is the nearest railroad point.

Jan 1, 1931

By Arthur L. Murray

The first thought in the case of an accident or contagious disease is naturally that aroused by our humane instinct , how serious is the case and will the person recover ? The economic effects of such cases , owing to their many ramifications , are seldom realized either by those directing mining operations or those engaged in the labor of producing . This paper is based on the accident experience of the State of Utah and the number of cases of two well known preventable diseases , typhoid fever and smallpox , in that State for the fiscal years 1917-1918 , 1918-1919 , 1919-1920 , and 1920-1921 . The data and figures presented are from coal -mining camps only . W. W. Adams , mine- accident statistician of the bureau, contributed valuable corrections and suggestions . The economic results of accidents are considered first , and those of the two preventable diseases later .

Apr 1, 1922

By William H. Lyon

In 1950 the Program Staff of the Department of the Interior undertook an exploratory study in the projection of energy requirements of the nation. This work was reported in Bureau of Mines Information Circular 7582 by H. J. Barnett. In that preliminary study Mr. Barnett, after exploring the nature of the energy economy in some detail, evolved a method for estimating how much energy will be required in the future, based on estimates of trends in efficiency of energy utilization in specific applications, the physical output of specific energy-consuming industries, size of the population, productivity advances in the economy at large, consumer preferences, and other factors. Considerable new information was developed regarding the nature of energy demands and the possible levels of requirements for each fuel under various assumed business conditions. The study analyzed the interrelationships, including substitutions, among the fuels and emphasized the need for viewing the energy economy as an integrated albeit complex whole. This exploratory study showed a need for a single comprehensive statistical re-port that would assemble and show in a uniform manner the diverse published statistical data on energy commodities now scattered through many publications. A particularly important need was for a set of historical statistics showing the production and consumption of all energy on a B.t.u. basis. As the prospective size and nature of the future energy requirements of the nation are matters of continuing importance, this report was prepared to assist further investigations of the subject. In this report the authors undertake to assemble and present in tabular form, on a uniform basis, the production and use of each of the fuels and electric energy in the United states for three census years -1929, 1939, and 1947. The year 1947, rather than a later year, was selected because it is the most recent year for which census data are available showing the consumption of fuel by each of the manufacturing industries. It is hoped that making data for these 3 years available in one re-port will provide the needed statistical background for further studies of fuel requirements and supplies.

Jan 1, 1951

By Ivette E. Torres

Of the 15 selected non fuel mineral commodities detailed in table 12, only 3 indicated increases in worldwide consumption in 1992. As in 1991, decline in consumption levels of the selected commodities can be attributed to reduced levels of use in the former U.S.S.R. and Eastern Europe. Of the remaining 12 commodities, 2 magnesium and cadmium, stayed relatively the same, while the other 10, including iron and steel, all recorded decreases. Global consumption of iron ore is estimated to have fallen about 3.5 % or about 30 million tons. This is a greater decline than what was estimated for production of iron ore, which is down only 2.7% or nearly 26.5 million tons, suggesting an addition to stocks. The consumption trend for iron and steel has been declining since 1989. This has mainly been due to the continued drops in use in the former U.S.S.R. and Eastern Europe. Even as the European economy begins to turn upward, there may only be a slight increase in consumption of iron, steel, and cement, considering the high cost of construction needed to modernize factories and buildings in Eastern Europe. Many feel that the economies of these countries are limited by the current status of their industries.

Jan 1, 1994

By L. B. Pankratz

High-temperature heat-content values of gallium and scandium sesquioxides were measured over the temperature range from 298° to 1,800° K. The results fill gaps in the thermodynamic information for these compounds; no previous similar data existed. The heat-content values were combined with heats and entropies of formation to obtain free energies of formation of gallium and scandium sesquioxides to 2,000° K. The thermodynamic stabilities of the sesquioxides of aluminum, gallium, scandim, and yttrium were compared.

Jan 1, 1963

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924