Search Documents

This Bureau of Mines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

By G. V. Sullivan

This report summarizes the results of metallurgical investigations by the Federal Bureau of Mines of manganese oxide ore, averaging 23 to 25 percent manganese, stockpiled at the Butte-Philipsburg depot of General Services Administration (GSA). The oxide ores were stockpiled in two general classifications, straight oxide ore and mixed oxide-carbonate ore. Continuous-circuit flotation tests at the Albany (Oreg.) Metallurgy Research Center of the Bureau of Mines showed that each of these ore types could be concentrated by an oil-emulsion scheme to produce a concentrate that could be sintered to meet program specifications. About 88 percent of the manganese was recovered in the concentrate from the straight oxide sample, with the sintered concentrate containing 48 percent Mn. The sintered concentrate from the mixed oxide-carbonate sample contained 41 percent Mn with a recovery in the concentrate of 95 percent.

Jan 1, 1961

By Vibration Research Group, Natasha K. Lee Shee, Tammy R. Eger, James P. Dickey, Paul-Émile Boileau, Lana M. Trick, Michele L. Oliver

Introduction Industrial exposure to whole-body vibration is associated with injury and discomfort. Certain industries, notably mining, construction, and forestry, involve complex 6 degrees of freedom vibration. Laboratory-based studies of vibration are essential for controlled and systematic evaluation of the human responses to vibration2. The purpose of this pilot study was to evaluate whether the duration of the vibration exposure, and rest between vibrations, significantly influence the subjective ratings of comfort during laboratory-based studies of vibration. Methods Subjects: The cumulative vibration dose was calculated, and was below the health guidance caution zone recommended by International standards3. The experimental procedures were approved by the University of Guelph Research Ethics Board. Ten adult subjects participated in this pilot experiment. All subjects completed the entire experimental paradigm; no subjects complained of pain during or after the experiment. Experimental Design: The experiment consisted of four blocks of vibration exposures; either 15 or 20 seconds of vibration (1 df:Z axis, 3 df:XY plane, 3df:YZ plane, or 6 df) alternating with either 5 or 10 seconds rest. The order of presentation of the four blocks was randomized. Each of the blocks was composed of 37 individual sinusoidal vibration exposures in randomized sequence. This abstract focused on ten identical trials, (6.3 Hz vertical vibration, 0.55 m/s2 RMS) interspersed within each block, in order to assess whether the subjects’ comfort ratings systematically varied between the 15 or 20 vibration exposures, the 5 or 10 second rest between vibrations, or within each block. The experiment involved 43 minutes of vibration within the 62 minute experiment. Vibration Apparatus: A commercial parallel robotic platform was used to apply the specific vibration exposures (R2000, Parallel Robotics Systems Corporation, Hampton, New Hampshire). The subjects sat on a passenger seat from a 1992 Honda Accord that was rigidly mounted to the robotic platform (Figure 1). This robotic system performed the specific vibration exposures operating under closed-loop displacement control. A custom-written Matlab program automated the testing sequence.

Jan 6, 2006

By D. K. Deardorff, Laurance L. Oden, H. Kato, M. I. Copeland

The equilibrium relationship of hafnium and tantalum was studied to facilitate alloy and property investigations . The data obtained are presented graphically as the equilibrium diagram . Alloys were prepared from high - purity components by nonconsumabletungsten- electrode arc melting . Data for the equilibrium diagram were obtained by optical pyrometry , metallography , X- ray diffraction of heat treated specimens , X- ray diffraction using a high- temperature camera , and differential thermal analysis . During the investigations , a casting apparatus was constructed , and the existing melting - point apparatus was improved . The bcc allotrope of hafnium forms a continuous series of solid solutions , called beta , with tantalum which exhibit a minimum melting point at 20 wt pct tantalum and 2,110 ° C. At 24 wt pct tantalum and 1,050 ° C , hafnium- rich beta decomposes in a monotectoid reaction to yield alpha and tantalum- rich beta . The monotectoid isotherm extends from 5.5 to 60 wt pct tantalum . The twophase region , in which hafnium- rich and tantalum- rich beta solid solutions are immiscible , rises to a maximum temperature of 1,265 ° C at 38 wt pct tantalum . The solubility of hafnium in tantalum decreases from 40 wt pct at the monotectoid temperature to 20 wt pct at 750 ° C.

Jan 1, 1964

By L. J. E. Hofer

This Bureau of Mines study, part of a broad program of research in air pollution related to minerals, was conducted to determine the nature and extent of the poisoning of catalysts when used to remove certain air pollutants from exhaust gases. The poisoning examined in this investigation occurs when leaded gasoline is used as a fuel for automotive engines. This research was conducted in cooperation with the Public Health Service. The smog in the Los Angeles area is attributed to the effect of radiant energy on the mixture of hydrocarbons and nitrogen oxides found in the atmosphere there. A large portion of the hydrocarbons is believed to originate in the exhaust gases of automobiles. To prevent the escape of these hydrocarbons into the atmosphere catalytic mufflers have been proposed. In principle, these are simple and nonmechanical, consisting of a vessel charged with a catalyst capable of destroying the exhaust hydrocarbons by catalyzing their oxidation. However, these catalysts are severely affected by the particulate matter, mainly in the form of lead sulfate (PbS04), lead oxysulfate (PbS04.Pb0), and Lead chlorobromide (Pb(Cl,Br)2), contained in the exhaust gas. Deposition of lead on the catalyst as PbS04, PbS04, PbS0, and Pb(Cl,Br)2 restricts catalytic activity. As a result,after 20,000 miles of operation the temperature necessary to achieve 50-percent conversion of isopentane in a mixture of 0.2 percent isopentane, 2 percent carbon monoxide and 4 percent oxygen, and the balance nitrogen at 10,000 hourly space velocity has risen from 400° C. to 500° C. even with a catalyst taken from the exit portion of the catalyst bed. The rest of the catalyst was more severely affected. Therefore, it would appear that operation for 20,000 miles is near the limit for a catalyst.

Jan 1, 1963

By J. E. Spurr

"Zinc Industry in BelgiumBy March F. Chase, Consulting Metallurgist, Bureau of MinesBelgium for many years was the principal spelter producing country of the world. Gradually its production was surpassed by that of Germany, and Germany in turn lost first place by the production in the 77ti.tad States. For the ten years previous to 1914, 21.6 per cent of the world's spelter was produced in Belgium. Of this production approximately 40 per cent was exported. A large percentage of the balance was rolled and of the shoots thus produced a considerable quantity was also exported.From an economic standpoint even before the war, the Belgian industry was in a unique, if not praoarious, position. Dependent upon foreign countries for ore and foreign markets for sale of products, smeltor was at a distinct disadvantage when compared with some of those of other localities. These disadvantages were partly offset by cheap coal and labor and by whatever there is of value in experience and what we may term for want of a better expression smelting tradition. However intangible this latter may be, it did have and has today an influence on commercial operations.One must not overlook the effect it will have on the revival of the industry. It may not be the determining factor but the fact that for so many years this industry flourished in Belgium, and played such an important role in the industrial life of the country will decide many operators to attempt to re-establish their operations.In 1913 the Belgian spelter plants produced 204,220 long tons of spelter or approximately 20 per cent of the world's production. During this year 500,000 to of ore were treated. The actual value of all of the products derived from treating sine ore amounted to 225 million frames."

May 1, 1919

By J. P. Bennett

Based on previous Bureau of Mines research indicating that improved high-temperature properties could be achieved for periclase refractories through chemical additions, the Bureau investigated the properties of full-size bricks produced from chemically modified periclase refractory grains and the suitability of making such chemical additions to Mg(OH)2 slurries prior to production of the periclase grains. In full-size brick testing, strength values, both hot and cold, for the optimized bricks were superior to those for a commercial 98-wt-pct-MgO refractory. The best results were obtained for a natural magnesite with an adjusted CaO:Si02 (C:S) ratio of 3.0 and a 1.0-wt-pct addition of Zr02 and for a seawater periclase with an adjusted C:S ratio of 2.5 and a 0.5-wt-pct addition of Mn02. For samples produced from chemically modified Mg(OH)2 slurries, additions of both Mn02 and Zr02 and an increase in C:S ratios produced significant increases in hot flexural strength, similar to those resulting from chemical additions made to periclase grains. The most effective modifications were additions of Mn02 to brine-derived periclases having a C:S ratio adjusted to 3.0. These results on chemically modified magnesia refractories indicate that such material could potentially substitute for magnesiachrome refractories containing imported chromite.

Jan 1, 1984

By Ernest W. Loya

The Bureau of Mines has developed a computer program for calculating the composition of gravimetric primary standard gas mixtures. The Fortran IV program applies corrections due to buoyancy variations of the cylinder and inaccuracies of the balance weights. The program also determines the statistical error due to the sensitivity and precision of the balance and applies the analytical error of the weighed gases.

Jan 1, 1985

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the nonmetallic mineral industries (except stone and coal) for 1968-69. For each of the years, 23 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By Louis A. Panek

The practice of roof bolting or rock bolting to stabilize rock surrounding underground excavations has increased tremendously within a few years. This widespread application has led to many questions concerning the mechanics of bolting and has pointed up the need for a quantitative method of designing bolting systems. To answer these questions a research program was initiated to determine the principles of roof bolting. The first problem chosen for investigation was the use of bolts to reinforce bedded roof, since the great majority of bolts are used under these conditions. The attack employed is a combination of theoretical and experimental stress analysis. Centrifugal testing of models was chosen as the experimental method because it is particularly suited to the study of stratified roof. This report describes the models, the experimental method, and the model-prototype relations. By using dimensional analysis, a general expression for a roof-bolting design formula in terms of the structural variables has been obtained. Certain model-prototype similarity requirements have been relaxed, thereby minimizing the number of variables to be studied and extending the applicability of quantitative test data to a large class of full size structures.

Jan 1, 1956

By G. G. Campbell

Bureau of Mines research to develop an in situ retorting recovery method for oil shale has involved field testing of fracturing techniques for creating fluid-flow paths in impermeable oil shale. Electrolinking, hydraulic fracturing without and with sand propping, and explosive fracturing with a liquid explosive were tested in a 25-ft-square, five-spot pattern. These wells were drilled into oil shale at 50-to 88-ft depths near Rock Springs, Wyo. Results of the fracturing tests were evaluated by injecting air into a test well and measuring flow rates and flow profiles in adjacent test wells before and after each test. To identify points of air entry (location of fractures) in wells, flow profiles were determined by use of inflatable packers and by continuous logging with an airflow probe developed during the fracturing program. Electrolinking and hydraulic fracturing without sand propping were relatively ineffective; hydraulic fracturing with sand propping created horizontal fractures with desirable flow capacity; and fracture flow capacity was significantly increased by detonation of nitro-glycerin displaced in the natural and hydraulically induced fracture systems.

Jan 1, 1970

By Thomas J. Albin

This U.S. Bureau of Mines report identifies potential causes of slip-and-fall accidents occurring during surface mine equipment maintenance and describes the relative roles of direct worker behavior and machine design. The relative roles of human behavior and machine design in the causation of slip-and-fall accidents were determined through analysis of accident records, observations of maintenance worker behavior, and evaluation of mine machinery. From these data, relative risk ratios were calculated. Behavior had a relative risk ratio of 1.5; machine design, specifically access systems design, had a relative risk ratio of 2.2. Of the access systems, ladders had the highest relative risk ratio, 7.0. This study suggests that accident intervention would be most profitably made in improving the design of systems used to access maintenance worker areas of mining equipment.

Jan 1, 1990

By Ronald S. Conti

This U.S. Bureau of Mines (USBM) report describes various fire-fighting resources available to the mining industry and examines the fire preparedness of four western coal mines. Information regarding fire-fighting equipment indicates that an inadequate maintenance program may cause component failure of fire extinguishers, damage to waterhoses is usually a result of improper care, and foam may be a convenient means of conveying water to the fire. Performance data relative to water nozzles (throw distance) and specific practices to improve the state of preparedness in many of these areas are discussed. Studies also indicated that a high-expansion foam plug, will travel down an entry, with a 1% rise in elevation, 207 m (680 ft) before a plywood stopping separating the generator and plug failed. The advance rate of the foam plug decreased when the entry is dry, requiring more foam concentrate and as the foam spread further down the entry. An examination of the mines showed state-of-the-art monitoring systems were common at the minesites. Fire safety was also stressed, including early detection and rapid response of the miners to evacuate the mine. However, the mines placed little emphasis on performance of water nozzles, or personal protective clothing for the underground firefighters.

Jan 1, 1994

By A. S. Swanson

In view of the necessity or increasing production of metallurgical fluorspar to satisfy wartime demands, 0, M. Bishop, former district engineer of the Bureau of Mines, L. W. Carrier and. J. S. Williams, senior geologist of the Federal Geological Survey, and E. H. Dawson, mining engineer of the War Production Board made a joint survey of the Illinois-Kentucky fluorite district in July 1942 to determine what steps should be taken to increase production. As part of their recommendations, a program for exploring the idle Klondike mine in Livingston County, Ky., was outlined. All the ore produced at the Klondike mine was mined above the 325-foot level, where some tonnage remains. Factors that influenced selection of the Klondike mine for exploration were favorable geological conditions, the state of mine development and the availability of pumping equipment and some usable mine and mill equipment. In December 1942, the Metals Reserve Co. leased the Klondike mine from the Salem Fluorspar Co.

Jan 1, 1949

By G. W. Jones

The Bureau of Mines has advocated the use of stenches as warning agents in metal mines and in gas-distribution systems since 1920 A considerable amount of research has been conducted on ethyl mercaptan and other compounds to determine their effectiveness when used for this purpose.4/5/6/7/8/9/10/11/12/13/ Miners are warned of danger by a stench injected, in measured quantity, into a compressed-air line through which it is rapidly carried to the working faces, where it escapes from the compressed-air equipment and imparts a characteristic odor to the air. This method is not applicable to mines where only a limited number of com-pressed-air lines are used, as for example, many coal mines; the ventilation currents available in these mines may be too slow for warning purposes.14/

Jan 1, 1954

By Paul M. Tyler

Hafnium appears to be among the more abundant of the newly discovered elements . Though quite widely distributed in nature , its compounds chemically so resembled those of zirconium , its sister element , that it escaped detection until 1923 , when Coster and Hevesy announced the discovery of the element , to which they gave the name of " hafnium " , from Hafniae , the Latin name for Copenhagen , where their research work was performed . Hafnium has so far been found only as a minor constituent of zirconium minerals . Zirconium as an element was discovered more than 140 years ago , but only a few unimportant uses were found for the metal or its compounds until some 18 years ago ; it is still classed among the rarer commercial metals . It is not surprising , therefore , that hafnium has not yet found a definite place for itself in industry . Nevertheless it has commanded a considerable interest among scientists ; and in 1930 some 70 grams of perfectly pure oxide of hafnium were prepared in Europe . A commercial future for hafnium is already glimpsed in the radio industry , and its high melting point and electronic emissivity have already led to the taking out of patents for its use in radio tubes and incandescent electric lamp filaments and for the cathode surfaces of devices such as X- ray tubes and rectifiers .

Apr 1, 1931

By Howard P. Hamlin, John W. Sweeney

Shales from 14 locations in Indiana were sampled , tested , and evaluated to determine feasibility of producing lightweight aggregates by rotary - kiln and sintering methods . Sampling procedures and the geology of the significant shale units are discussed . Preliminary testing was conducted in a muffle furnace , and continuous tests were made in a 16 - inch by 14 - foot rotary kiln . The aggregate weighed 37.0 to 47.2 pounds per cubic foot . Concrete cubes employing the aggregate were tested to determine the qualities of the concrete . Compressive strength of the concrete using seven bags of cement per cubic yard , after autoclave curing for 6 hours , ranged from 3,600 to 5,850 pounds per square inch . Four samples made suitable lightweight aggregate in the laboratory rotary kiln . Four samples tested by sintering methods made unsatisfactory aggregate .

Jan 1, 1965

By Leon W. Dupuy

Marquette's first reported the existence of iron In Missouri in 1673. Recorded production wan begun in 1815, increasing in size and importance until 1888, when the low price of iron resulting from Minnesota's production of high-grade ore caused most of the operators to close down. Missouri's iron production came from three types of ore: (l) Brown ores, including the deposits of primary and secondary limonites in southeast and southwest Missouri, (2) hematites of the filled sinks, including the ores of Central Ozark district, and (3) specular ores in porphyry, including the deposits of the St. Francois Mountains.

Jan 1, 1949

By Mulligan John J.

The Bureau of Mines investigated lode tin deposits on Potato Mountain, Seward Peninsula, Alaska. Tin was found to occur as cassiterite associated with quartz, tourmaline, pyrite, arsenopyrite, and earthy clays, but the deposits lack the varied accessory minerals commonly found in tin districts. The tin-bearing deposits are in metasediments along minor breaks and bedding planes but not in the crushed earthy filling of major faults. Cassiterite and sulfides occur with quartz in veins, both with and without earthy clays, and disseminated through tourmalinized wall rocks. The deposits are characterized by irregular segregations containing 1 to 10 percent tin within zones averaging not over 0.25 percent tin. The largest segregation exposed is on the summit of a low hill on the east-central slopes of Little Potato Mountain; most of the outcroppings are in an area trending east to west, roughly 10 to 30 feet wide and 300 feet long. Sample values ranged as high as 12 percent tin, but the average grade may be about 1 percent tin. The extreme irregularity of both grade and composition precludes a more exact determination. Similar concentrations are scattered for over 1,000 feet to the west and north, but these are smaller and lower in grade. Elsewhere on Potato Mountain, generally similar deposits occur as clusters of veinlets at widely separated points in the metasedimentary walls of major faults.

Jan 1, 1965

By Frederick K. Allgaier

This is the first in a series of progress reports on the longwall subsidence research program at the Bureau of Mines Denver Research Center. As part of this program, the Bureau and the Utah Power and Light Co. are cooperating on a study conducted at the Deer Creek Mine, which is directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. A monitoring network has been established at the Deer Creek Mine to measure subsidence over four adjacent longwall panels. To date, two panels have been mined. Subsidence began as the first panel was mined and continued for 1 year following completion of the panel, during which time the adjacent panel was mined" A maximum of 2.7 feet of subsidence occurred over the two longwall panels mined at a depth of 1,500 feet. Because of the length of time that subsidence continued after mining, the final subsidence profiles and angle of draw have not yet been determined.

Jan 1, 1982