Search Documents

By E. J. Matson

The Table Mountain copper deposit is in an isolated portion of north-eastern Churchill County, Nev. Although copper-bearing outcrops have been known to exist in the area since 1909, no copper ore has been mined. Development of the property has been hampered by poor roads and rugged topography. Until 1941, the last 4 or 5 miles to the property had to be traveled either by foot or pack animal. As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a project was started at the Table Mountain deposit. The Bureau began its field work on July 29, 1947, and completed it on October 18, 1948. Thirteen holes aggregating 2,711 linear feet, were drilled; samples were analyzed - 509 from cores and 143 from sludges. This report contains a brief history of the district and a description of the geology, deposits, and drilling done by the Bureau.

Jan 1, 1949

By C. L. Klingman

The Bureau of Mines tested eight commercially available, activated charcoals experimentally to compare the following characteristics: capacity for adsorption of nitrogen at 77° K and 170 atmospheres' pressure, surface area, carbon tetrachloride adsorption capacity, hardness, and density. The nitrogen adsorption test was devised to simulate plant conditions occurring in the final step of purification in Bureau helium faciliti.es. The remaining tests were patterned after empirical acceptance tests that are widely used throughout the adsorbent industry. Surface area and carbon tetrachloride adsorption correlated well with nitrogen adsorption. The samples with low density generally had better adsorption qualities than those of higher density. The carbon tetrachloride test appeared to be the most practical for selecting a charcoal to be purchased, but an attrition, or hardness test should also be run to be sure the charcoal will not crumble in use.

Jan 1, 1966

By Louis C. Srichta

The rapid depletion of known high-grade ore deposits of the Tri-State district and the recognized need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores led to Bureau of Mines examination of several abandoned mining areas for possible deposits adapted to strip mining. Examination of the North Empire tract in Cherokee County, suggested that mineralized zones contiguous to previously mined 2e deposits presented probabilities of meeting the requirements for an open-pit mine - hence the tract was selected for further investigation by churn drilling. The zinc-lead deposit on the property is in a sink-hole structure that has been subjected to intense deformation and silicification. Numerous shafts, mine dumps, and surface caves are evidences of exploitation of an extensive area. The reported active mining period was 1895 to 1905. No production records are available, but it is generally stated locally that the value of the mill products exceeded $2,000,000 which represents considerable production, considering the low metal prices of that epoch.

Jan 1, 1950

By G. L. Oldright

[Processes by which silver alone is extracted from ores that also cant contain base metals are usually associated in the mind of the period when mines were changing from the production of noble metals to the production of base metals containing noble metals as a by-product. In this transition period the mixed arcs of the partly oxidized ore zone had to be treated instead of the free-milling ore that had been treated in the past or the deeper-lying sulphide ores that were to be smelted subsequently under improved economic and technical conditions.]

Jan 1, 1929

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By Gary A. Halvorson

Plots were established on regraded abandoned mine spoil to determine if nearby good quality spoil could be used in place of topsoil for the reclamation of these sites. Gypsum, calcium chloride, and power plant ash were also tested to determine the effectiveness of these materials in reclaiming these sites. Two sites were selected on which very little vegetation was growing on highly sodic spoil material. Gypsum, calcium chloride, and ash were added to the spoil at a rate designed to reduce the (sodium adsorption ratio) SAR in the surface 15 cm to 10 or less. The good quality spoil (replacement soil) was then laid on the swface at rates of 0, 5 or 15 cm of material. The plots were seeded to a mixture of smooth bromegrass (Bromus enennis Leyss.), crested wheatgrass (Agropyron desertorum (Fisch. Ex Link) Schult.) and alfalfa (Medicago sativa L.). The addition of 5 or 15 cm of replacement spoil significantly improved vegetative growth on these sites. Chemical treatments had no effect on vegetative growth. Weathered ash showed no adverse effects on plant growth or soil properties.

Jan 1, 1991

By Richard P. Cislo

The evaluation of the effectiveness of the time domain Coal Interface Detector developed by the General Electric Company under contract H0155120 is the subject of this report. The sensor utilizes differences in the time characteristics of shearer vibrations as sensed by an accelerometer mounted on the ranging arm to discriminate the cutting of coal and rock. Pour identical time domain sensors were supplied by the Bureau for field evaluation. The performance of the time domain sensor was evaluated by an extensive field test and data collection program that included four longwall mines and a total of nine mine visits. The intent was to determine the sensor's applicability to a wide range of mining conditions and to document its limitations. Results of the extensive field tests indicate that shearer vibration data processed by GE's time domain signal processing algorithm cannot be used to reliably detect when the cutting drum crossed the coal/rock interface.

Jan 1, 1987

By W. F. Watts

In 1980 the Bureau of Mines developed the Mine Inspection Data Analysis System (MIDAS). MIDAS is a computerized, industrial hygiene data base capable of statistically analyzing environmental data collected in coal and noncoal mines and mills by Mine Safety and Health Administration (MSHA) inspectors or mine operators. The objectives of this report are to describe the current contents of MIDAS, to report analyses of coal and noncoal mine respirable dust samples collected by MSHA inspectors and to evaluate the proposed change in the metal and nonmetal respirable dust standard from a formula based upon the percentage of quartz identified in the sample to 100 µg/m3 of respirable quartz. Based on samples collected by MSHA inspectors, changing the noncoal respirable dust standard would result in 4 pct fewer samples with dust concentrations exceeding the standard. Analysis of respirable coal dust data collected by MSHA inspectors showed that mines with longwall plows or shears had the highest geometric mean concentrations (1.64 and 1.29 mg/m3, respectively). Mine operations using continuous rippers out-numbered longwall mine operations about 10 to 1 and had a geometric mean concentration of 0.66 mg/m3.

Jan 1, 1987

By F. D. Cannon

"In metal and nonmetallic mineral mines during the 15-year period 1911 to 1925, 30.17 per cent of all fatalities and 16.57 per cent of all injuries were caused by falls of rock or ore from the back or roof or from the wail; 1.24 per cent of the fatalities and 11.05 per cent of the injuries were caused by rock or ore while loading at the working face; 6.66 per cent of the .fatalities and 2.49 per cent of the injuries resulted from men falling down 3 chute, winze, raise, or stope; and run of ore from chute or pocket caused 1.48 per cent of the fatalities and 1.93 per cent of the injuries.3 Hence, accidents due to falls of men and material caused. 39.55 per cent of the fatalities and 34.05 per cent of the injuries in these mines. Accident prevention can best be assisted by each company's preserving complete records of accidents classified according to cause and rate per thousand or 10,000 shifts. A systematic method of recording accidents and the employment of graphs or charts will be helpful to the company safety department in analyzing the cruses of accidents. The purpose of this publication is to analyze data on accidents caused by falls of men and material in metal -mines of the United States, and to suggest methods of preventing or reducing such accidents."

Jun 1, 1929

By George L. Gates

It is generally recognized that if the lose and contamination of the fluid content of a core specimen from an oil- and gas-bearing formation in a well were eliminated, the value of core analysis would be increased greatly. In an effort to obtain uncontaminated cores, extensive field tests were carried out in the Mercy field, San Jacinto County, Tex., with the Carter pressure core barrel and an oil-base drilling fluid having very low rates of filtration as measured by the standard A.P.I. drilling-fluid filter teat. A tracer was added to the drilling fluid filter test. A tracer was added to the drilling fluid to provide a means for quantitatively measuring the volume of oil filtrate in the cores. Unfortunately, as stated in the report on the Mercy tests, very little oil nand was penetrated in coring the well; and because the performance of the pressure core barrel was not entirely satisfactory, the tests did not provide a complete answer to the question: Does a filtrate from an oil-base drilling fluid enter cores., and how does it affect the results of the core analyses?

Jan 1, 1950

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau's turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987

By S. J. Rodgers

This report presents the results of in-mine studies to determine the severity of dust sources in conventional mining operations. Three underground coal mines were surveyed using gravimetric samplers and GCA RAM-1 continuous dust monitors. Two additional mines were surveyed using only GCA RAM-1 monitors. Data on dust control methods were acquired during the survey, also. The results indicated that cutting/drilling and loading out were the dustiest operations during a conventional mining cycle. Roof bolting, shot firing and product transport were less severe dust sources.

Jan 1, 1983

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By R. O. Pynnonen

This publication presents a study by the Federal Bureau of Mines of 494 accidents in open-pit iron-ore mines, beneficiation plants, and shops of the Lake Superior district from March 1949 to June 1956. These accidents caused 499 lost-time injuries, including 12 fatalities. A similar Bureau publication, Information Circular 7744, Analysis of 346 Accidents, Underground Iron-Ore Mines, Lake Superior District, was published in April 1956. Accident reports were analyzed by the Bureau to show the causes of in-juries and the unsafe practices or conditions that caused the accidents. Also shown are the time charges, times of occurrence, ages of the injured by job classification, and experience of the injured in mines and on the job being performed when hurt. Detailed information is presented on approximately 27 percent of the total number of disabling accidents that occurred in open-pit iron-ore mines, beneficiation plants, and shops in the district during the period covered. The text also contains tabulations of the accident experience and graphs with straight-line injury-frequency, injury-severity, and fatality trends for the period 1946-57.

Jan 1, 1959

By Michael Sokaski

A dense-medium cyclone pilot plant was built to clean 112-inch to 0 size coal. This pilot plant does not require the removal of the extremely fine material (usually minus 1/2-mm) from the feed, which is necessary in conventional dense-medium cyclone plants. The essential difference between conventional cyclone plants and the pilot plant is in the medium-recovery system. The latter uses a combination of sieve bend screens, classifying cones, and magnetic separators for medium recovery. Eight tests were run in the pilot plant at a feed rate of 5 tons per hour with four different raw coals and one crushed jig middling product. Sharp separations were obtained as indicated by an average error area of 27 and probable error of 0.047 for the 112-inch to 200-mesh size range. Magnetite loss averaged about 2.5 pounds per ton of feed. The influence of several factors on cleaning performance of the cyclone was investigated. The diameters of both the overflow and underflow orifices were found to be important for optimum cleaning performance, but these diameters could vary over a wide range without serious effect; however, if this range was exceeded, cleaning performance deteriorated. Better cleaning performance was obtained when the cyclone inlet pressure was increased from 9 psig to 13 psig. The size of the magnetite particles in the medium was found to have a substantial effect, and the best cleaning results were obtained with grade B magnetite. Demagnetizing the magnetite in an effort to decrease the effective particle size did not improve cyclone performance.

Jan 1, 1963

By F. P. Haver

Because State and Federal agencies have limited the amount of sulfur oxides that can be discharged to the atmosphere, most copper smelters plan to convert the S02 in offgases to sulfuric acid. In some cases, however, it might be preferable to use a nonsmelting method to fix the sulfur in the form of a discardable product. Research by the Federal Bureau of Mines has shown that sulfur in copper concentrate can be converted into insoluble anhydrite (CaS04) by roasting the concentrate with lime (CaO). After leaching the calcine to recover metal values, the residue may be discarded without harm to the environment. The process can use a rougher flotation product, thus reducing separation costs and saving valuable minerals (for example, molybdenite) that are now lost in making cleaner concentrate. In tests, rougher concentrate was pelletized with the theoretical amount of lime and roasted for 1 hour in a 6-1/2-inch-ID by 11-foot-long rotary kiln at 700° C. Sulfur retention was about 97 percent. Leaching the calcine with 20 percent RCI extracted approximately 99 percent of the copper, 73 percent of the iron, and 91 percent of the molybdenum. After the molybdenum was removed from the leach solution by adsorption on activated carbon, copper with a purity in excess of 99 percent was obtained by cementation on sponge iron. The strip solution then could be spray-roasted at 500° C to recover the RCI for recycle and obtain F2O3 as a byproduct.

Jan 1, 1975

By W. P. Yant, C. E. Traubert

"INTRODUCTION Canister-type gas masks have become an essential part of the equipment of many industries, not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres.Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investi-gations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.TYPES OF CANISTERS EXAMINEDThis investigation included tests of the following types of canisters:(a) Gas-mask canister filled with 725 c.c. of granular activated charcoal, 8 to 14 mesh, and of a quality used in gas masks which meet the Bureau of Mines approval requirements 4 for protection against organic vapors."

Oct 1, 1932

By Robert S. Warfield

The Federal Bureau of mines and U.S. Geological Survey conducted exploratory investigations and geologic mapping in the Wishbone Hill district of the Matanuska coalfield almost continuously from 1942 through 1958. These investigations delineated reserves of high-volatile bituminous coal necessary to supply the rapidly expanding military and civilian requirements in the Anchorage area. This report describes the program conducted by the Bureau of Mines from 1949 through 1958, and briefly summarizes previous investigations, the results of which have already been published. The coal-bearing structure on both the north and south limbs of the prominent Wishbone Hill syncline was explored by 8,719 feet of churn drilling and 25,460 feet of diamond-core drilling. A total of 33 holes were drilled ranging in depth from 60 to 2,114 feet. To supplement the drilling operations, bulldozer and dragline trenching were undertaken at key locations; about 25,000 cubic yards of dragline trench were excavated in the vicinity of the old Premier mine.

Jan 1, 1962

By Robert W. Waytulonis

The mining regulations of all 50 States were reviewed by the Bureau of Mines, and those parts pertaining to the use of internal combustion (IC) engines (particularly diesel engines) in underground mines or confined spaces were extracted. Also extracted were subjects associated with the use of IC engines; for example, storage and handling of flammable liquids, maintenance, and ventilation requirements. As the laws now stand, 29 States have specific regulations that affect the operation of diesel engines in underground coal and/or metal and nonmetal mines. The other States have no regulations because either they have no mining activities or they defer to Federal regulations. Six states have regulations expressly prohibiting the use of diesels in underground coal mines. Specific contacts (addresses and phone numbers) precede each State's regulations to facilitate inquiries about regulation revisions and interpretation.

Jan 1, 1981

By Annie G. Smelley

As a part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U.S. Department of the Interior, is developing a dewatering technique that allows for disposal of clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weight nonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater materials containing clay wastes. In laboratory experiments, coal-clay waste, potash-clay brine slurry, phosphatic clay waste, uranium tailings, and talc tailings were successfully consolidated. Coal-clay was te was consolidated from 3-. 6 to 57 percent; potash-clay brine slurry was consolidated from 3.8 to 35 percent; phosphatic clay waste from 15.6 to 49 percent; uranium tailings from 15.4 to 67 percent; tailings from talc production from 9.7 to 53 percent; and an acidic Ti02 slurr slurry from 1.68 to 30 percent.

Jan 1, 1980