Search Documents

By Jr. Hazen

This report documents 653 sets of sample data involving 78,366 assays obtained from past exploration for various minerals and metals. Most of these data have been taken from published reports describing exploration projects, conducted jointly by the Bureau of Mines and the Geological Survey, for the Strategic Minerals Program from 1940 through 1949. Means and standard deviations have been computed for the exploration assay data and have been plotted on graphs for 22 minerals and metals. A mathematical model, based on the binomial distribution, has been developed to explain the configuration of the plots of the exploration means and standard deviations. The two statistics, mean and standard deviation, which describe assay data, have been used for simulating probability models. These probability models then have been combined with the binomial model of the exploration assays and related to the sequential decision process associated with exploration drilling for mineral deposits. These probability regions can be used to form the basis for sequentially predicting the probable range of the average grade of mineral or metal that may be expected as an exploration drilling program is continued after the initial discovery of mineralization has been made.

Jan 1, 1966

By Mark S. Sanders

Six underground coal mine shuttle cars (three high seam and three low seam) were used to assess visibility using the concept of visual attention locations (VALs) and an improved human eye reference measurement instrument (HERMI Mark II). Each machine was assessed in the inby and outby direction of travel with no canopy and with the canopy in its highest, and lowest position. In addition, the illumination level at each VAL was determined. Results showed that the most important variable determining visibility was operator eye position. When this variable is controlled, the addition of a canopy has no effect on visibility. Further, with eye position controlled, there is no difference in visibility between high and low seam machines. The visibility and illumination assessments found blind spots in the operator's field of view located on the opposite side of the car from the operator and ahead of the machine. Suggestions for reducing the blind spots were made. The report also included a procedure manual for using HERMI and the system of VALs to assess visibility from underground shuttle cars, continuous miners, and scoops.

Jan 1, 1983

By W. D. Mcmillan

Important reserves of nickel ore occur in the Levies district in Oriente, Cuba. The area is mountainous and mostly covered by heavy vegetation. The ore bodies comprise surface tracts of nickeliferous laterite underlain with decomposed serpentine of ore grade. The Cuban Nickel Co., a wholly owned United States Government corporation, owns a plant for leaching the nickel from its ores at Nicaro, Oriente, Cuba, Between December 1943 and March 31, 1954, 5,902,225 short tons of ore was treated, with a recovery of 116,206,519 pounds of nickel (52,711 metric tons). In 1953, 1,330, 224 short tons of ore was mined and 27;"3,129 pounds of nickel produced. The Cuban Nickel Co. also owns a townsite, with the necessary facilities, mining equipment, and 11 miles of railroad. Ore for the plant has been produced from the Ocujal-San Juan claims on lends owned by the Nicaro Nickel Co., a sub¬sidiary of Freeport Sulphur Co. The Government enterprise is man-aged by the Nickel Processing Corp. The Cuban Nickel Co. has denounced mineral concessions and has purchased other claims from private owners.

Jan 1, 1955

By Joseph J. Wallace

1. The investigation shows that there are 2 coal beds of major importance in Letcher County from the standpoint of present production - Upper Elkhorn No, 3 and Fire Clay - and 5 beds of minor importance - Whitesburg, Flag, Haddix, Elkhorn Leader, and Amburgy, The Upper Elkhorn No. 3 and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,600 tons per acre-foot of coal in place, are estimated at 1,353 million short tons as of January 1, 1952. Of this total, 1,056 million short tons ere in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bad characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By P. L. Woolf

Three trials with oxygen-enriched unheated blast air are described. The trials were conducted in the Bureau of Mines experimental blast furnace located in Bruceton, PA. The first trial utilized moisture addition to the oxygenated blast. The second and third trial were conducted with natural gas injection. The test was basically a feasibility study and in that regard the practice was demonstrated to be feasible and also have possible advantages over hot blast operation. The testwork was conducted in 1964 and 1965 as part of a continuing study of iron making technology in cooperation with several North American Steel Companies.

Jan 1, 1985

By R. Y. Williams

In this report an attempt is made to discuss the first cost of each of several types of mine-ventilation stoppings, as well as the total annual expense of maintaining a stopping during its required period of service. Such data furnish a basis for comparison of the efficiency of the different types, and are of great importance to an engineer planning the development of a mine. The data given were obtained through an investigation conducted under a cooperative agreement between the Bureau of Mines, the Illinois State Geological Survey, and the department of mining engineering of the University of Illinois. The report itself is published by the Bureau of Mines as a contribution to the literature on safety and efficiency in coal mining.

Jan 1, 1915

By T. E. Gray

This report describes the preparation characteristics of the more significant coals in Dickenson County, Va. It is one in a series planned to determine which coals are suitable for the production of metallurgical coke either as mined or after beneficiation. Nearly 4 million tons of coal was produced in Dickenson County in 1955, of which approximately 2.7 million tons was cleaned mechanically in 5 cleaning plants. The Federal Geological Survey has estimated that nearly 1,300 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By Richard J. Mainiero

The Bureau of Mines conducted research to evaluate the optimum design for a rock-breaking explosive charge that could be fired unconfined in a gassy or dusty coal mine without the danger of igniting the flammable atmosphere. Charges of various shapes, with and without cavities, were tested in a gallery using 3-by 3-by l-ft concrete blocks as simulated boulders. For these tests the optimum charge, in terms of cost, weight, and convenience in handling, consisted of a flat l-1/2-lb charge of permissible explosive seven-eighths of an inch thick and 7 in in diameter encased in a l/2-in thick layer of fine salt (NaCI). This work demonstrated that it should be possible to produce an inexpensive explosive rock-breaker charge that would be safe to use in underground coal mines.

Jan 1, 1982

This publication contains four papers presented at a seminar on mine subsidence control held in Pittsburgh, PA, on September 19, 1985. The seminar was designed to keep the mineral industry informed of new technology developed by the Bureau of Mines that permits reliable and accurate prediction of mine subsidence. The papers describe actual field studies undertaken by the Bureau to monitor surface subsidence over longwall panels. Topics discussed include the efects of subsidence on water table levels, the development of subsidence pre calculation methodology suitable for use with the specific lithological conditions of the Pittsburgh coalbed, an engineering comparison of technologies used in surveying for longwall mine subsidence, and a comparison of the process of subsidence over two different longwall panels.

Jan 1, 1985

By Sidney Katell

This report, covering the period January 1965 through December 1965, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the seventh in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are From the following sources:

Jan 1, 1966

By Oliver C. Ralston, Dorsey A. Lyon

Volatilization in retorts has been, until recently, the only commercial process of producing spelter, hence the zinc mine operators have had to meet the terms of the zinc smelters in regard to the following requirements: (1) Minimum percentage of zinc the ore must contain; (2) the chemical combination of the zinc in the ore; (3) the proportion present of those elements that interfere with the suceessful recovery of the zinc when the ore is retorted. In consequence of these requirements, only a comparatively small proportion of the zinc ores mined can be shipped directly to the smelters.

Jan 1, 1919

By Robert H. Merrill, James V. Williamson, David M. Ropchan, George H. Kruse

In- situ rock stresses were determined by flatjack and borehole - deformation methods . Estimates of the stress distribution around a flatjack were obtained by a combination of flatjack and borehole - gage techniques . The investigations were part of a study , conducted jointly by the State of California and the Federal Bureau of Mines , to determine the stress in rock at the site of an underground powerplant for the Oroville Dam near Oroville , California . The stress distribution around each of three flatjacks was nonsymmetric ; however , stresses obtained from 9 flatjack and 157 borehole measurements are considered reasonably accurate for engineering purposes . The stress near the edge of the openings is between 800 and 1,600 psi ; the stress in the undisturbed rock is approximately 500 psi , nearly hydrostatic .

Jan 1, 1964

By Herman W. Hill

This report summarizes research into the root causes of failures in mine power systems which impact safety and reliability. Abnormally low fault currents, due to arcing faults, self-excited systems, and fallen trolley wires are examined and quantified. The reliability of components which are critical for safety is studied, as well as reliability of components which are crucial to the mining pro cess. Failure rates are found through in-situ tests, accelerated life tests, studies of mine maintenance, and fault-tree analysis. Reliability data is used to predict fatalities and lost-time accidents through computer-aided fault-tree analysis. Analytical support tasks reported include the deriving of trailing-cable ampacities under cyclic loading, and the measurement of connected ground beds.

Jan 1, 1981

By Robert E. Wood

The compressibility factors, Z, of helium, nitrogen, and helium-nitrogen mixtures in the three-dimensional space of temperature, pressure, and gas composition have been related to the Leiden form of the virial equation of state. The dependency of virial coefficients through the fifth on temperature and gas composition has been established for the temperature range 133.15° to 748.15° K. Compressibility factors, Z, have been computed from the equation of state and tabulated as functions of gas composition, pressure, and temperature. Tabular values of Z are presented for 30.00 through 100.00 percent helium for temperatures from 240° through 700° R for pressures from 14.696 through 3,050 psia and for temperatures from 720° through 1,300° R for pressures from 14.696 through 1,500 psia. Tabular values of Z are presented at increments of 5.00 percent helium and 20° R, and, for pressures greater than 50 psia, at increments of 50 psi.

Jan 1, 1967

By N. A. Eilertsen, Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for controlling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

By Frank C. Townsend

Centrifugal model embankments with varying geometries and materials were constructed of- coal waste material, accelerated From 100 to 120 times earth's gravity, and subjected to various throughflow rates until failure occurred. Complementary laboratory tests were performed on the waste materials to obtain strength and permeability parameters for analytical calculations to predict observed centrifugal model behavior. Failures in the form of deep.-seated failure, or erosion and sediment transport or a combination of both, occurred in model embankments with 1V:1-1/2H and 1V:2H slopes when the phreatic surface due to seepage exited on the downstream slope: Positive seepage control, i.e., a toe drain successfully prevented sloughing and failures. Slope stability analyses agreed well, albeit conservatively, with observed model performance. Factors of safety ranged from 0.7 to 1.02 at the instant of failure for models with retrogressing slips as compared with 1.05 to 1.7 for stable embankments, These models verified existing criteria of a minimum safety factor of 1 3 and the necessity of positive seepage control.

Jan 1, 1980

By John C. Feeley

The methods used and the funds available for the development and oper- ation of shall mines and the reopening of small abandoned mines frequently present problems that tax the ingenuity and resourcefulness of the mining engineer far beyond that required in the mass production from large deposits. The objective of this paper is to describe in considerable detail the means whereby engineers have solved local problems in reopening an abandoned mine at which equipment, facilities, and funds were limited... The Etowah Coal & Iron Co. Gadsden red-iron-ore mine at Gadsden, Ala., 18 of interest in this category since it is the only independent red-ore mine under active development in the State. All other red-ore mines in Alabama are owned or controlled by the large iron or steel companies. The The mine, located on the southwest end of Shinbone Ridge in the outskirts of Gadsden lies in an ares once productive. but now idle, for many years. ore is relatively highgrade compared with that in the Birmingham area, but the bed is thin and somewhat lenticular. The presence of a large blast furnace at Alabama City, 3 miles from Gadsden, and the growing scarcity of red-iron ore supplies for it offered inducements for reopening the mine in 1946. Up to the time this circular was prepared (1947) only a small quantity of ore (about 1,500 tons) has been produced and shipped to the furnace. A force of 14 men was employed in sinking the main slope and developing a third "lift" (a local term for level) 100 feet below the old mine workings.

May 1, 1949

By W. J. Kroll

This report is concerned with the many sidelines that were investigated incidental to developing a process to produce ductile Zirconium by members of the staff of the Bureau of Mines laboratory, Albany, Oreg. The results of the main investigation, concerning the production of malleable zirconium by reduction of chloride with fused magnesium under helium, have been described in previous publications. These should be taken as a background to facilitate understanding of this work. Literature on the metallurgy of zirconium has been summarized in a separate publication (2), and references are given in this report only when new publications have to be considered or old ones stressed. Most of the observations described in this report can be applied to the problems involved in making titanium with virtually no change. In general, titanium is easier to reduce than zirconium, since its affinities are lower. Also, its chloride is easier to handle and keep clean because it is a liquid at room temperature.

Jan 1, 1952

By R. Blickensderfer

The laboratory wear testing capabilities of the Bureau of Mines are described, Wear tests are used to support the Bureau?s research efforts toward reducing the wear of equipment used for mining and minerals processing and any wear involving a loss of strategic or critical materials. The emphasis is on abrasive wear because it accounts for most of the wear losses that occur in mining and minerals processing equipment, Spalling wear, caused by repetitive impact in grinding equipment, also is included, Ten abrasive wear tests, including high- stress and low-stress and two-body and three-body conditions, are described: dry-sand, rubber-wheel abrasive wear; Taber Abraser; abrasion resistance of refractory materials; dry-particle erosive wear; elevated-temperature, dry-particle erosive wear; low-angle slurry pot; jaw crusher gouging wear; ball mill wear; pin-on-drum abrasive wear; and high-speed impact gouging. Two repetitive impact tests are described: ball-on-block impact-spalling and ball-on-ball impact-spalling. Test equipment, procedures, and specimens are described, and typical test results are presented and discussed.

Jan 1, 1985

By M. Clair Smith

This report is one of a series describing exploration, development, mining methods, and costs at United States open-pit mines; the Bureau of Mines prepares and publishes them in cooperation with the mining companies. Their purpose is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods and practices at various United States mines. The exploration, development, equipment, and mining of a large, oxidized-copper ore deposit by open-pit methods, the leaching of the ore with sulfuric acid solution, and the recovery of the copper as cement copper are described herein.

Jan 1, 1958