Search Documents

By C. Edward Chamberlain

A Bureau of Mines procedure was developed for the analysis of volatile matter in airborne coal dust-rock dust mixtures prior to, and resulting from, coal mine fires and explosions. Dust in the 10-to 20-mg weight range can be analyzed. Volatile matter is determined by a greatly scaled-down version of the empirical macro-scale method used by the Bureau. The alkaline earth carbonates in the rock dust are dissolved in acid prior to the volatile matter determination of the residue, and the rock dust content is calculated from the analysis of calcium and magnesium by atomic absorption.

Jan 1, 1974

By William H. Holley

Thirteen additional preservative/fire retardant systems were applied to Ponderosa pine and evaluated for flammability both before and after water leaching. The more promising four systems were given a thorough evaluation for flame spread, toxic gas and smoke density levels, resistance to decay, and compressive strength. The most promising system on the basis of history of usage in the mine, ease of application and low cost as well as overall performance is the Fyreprufe/ACC Albi 107A/ 144 combination. A survey of inspection tools and instruments, identified equipment which could be assembled into an inspection kit for use in determining the extent of decay and/ or impregnant retention levels in mine timber. A literature search identified those high fire hazard areas found in a typical mine. Timber and other wooden structures used in such areas should be treated with an acceptable fire retardant system. A survey of insurance companies revealed that the use of such treated timber in the mines would probably have little or no impact on the rate structure.

Jan 1, 1980

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

By Albert L. Toenges

(1) The Castleman Basin was investigated by diamond drilling, engineering examination, and geologic study. Agreements permitting investigation of about 14,700 acres of land were entered into with 79 landowners. Eleven beds of coal between the horizons of the Harlem and Mercer beds were penetrated in drilling. These beds from top downward are: Harlem, Upper Bakerstown, Lower Bakerstown, Brush Creek, Upper Freeport Rider, Upper Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Mount Savage, and Mercer. The total estimated reserves of coal (measured, indicated, and inferred), 14 inches or more thick, in six beds follow: [Coal bed: Etimated reserves, tons Harlem _______________________ 23,430,000 Lower Bakerstown _______________ 44, 688, 000 Brush Creek ____________________ 23, 694, 000 Upper Freeport __________________57, 731, 000 Upper Kittanning ________________ 40, 450, 000 Middle Kittanning ______________42,276,000 Total________________________ 232,269,000]

Jan 1, 1952

By B. J. CROSS., Henry Kreisinger, John Blizard, C. E. Augustine

This bulletin presents the results of 36 tests made on a 468-horsepower Edge Moor boiler fired with pulverized coal at the Oneida Street Station of the Milwaukee Electric Railway & Light Co., Milwaukee, Wis. The tests were made by the fuel section of the United States Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation. Illinois coal was used as fuel; the furnace, burners, and feeders were designed by the Locomotive Pulverized Fuel Co. The object of the tests was to determine what over-all boiler efficiency could he obtained with pulverized coal under various conditions of furnace operation and with coal of different fineness and moisture content. The investigation was thorough. The pulverized coal, as it was supplied to the furnace, was weighed in specially designed tanks placed on platform scales. Twenty-nine of the tests were of 24 hours duration, three of 16 to 18 hours, and four of 12 hours. All tests are reported excepting two-8 and 20-which had to be stopped abruptly, No.8 because a motor actuating the coal-feed screw burned out and No. 20 because of trouble with the feed pump. Tests 1 to 27, inclusive, were made with round burners and tests 28 to 3Rwith spreading burners. In the first nine tests a large excess of air was supplied in an effort to prevent the ash fusing at the bottom of the furnace. In tests 10 to 16 the supply of excess air was reduced in order to get a high efficiency, regardless of the slagging of ash at the furnace bottom. Tests 17 to 27 were made with a water screen about 10 inches above the bottom of the furnace, to make possible the burning of coal with a small supply of excess air without the ash fusing at the bottom of the furnace. Tests 28,29, and 30 were made without the water screen and with a small supply of excess air, and tests 31 to 38 with a water screen around the walls near the bottom of the furnace. Tests 32, 33, 34, and 35 were run with coarser coal than that used ordinarily at the plant. Tests 36,37, and 38 were made with undried coal.

Jan 1, 1923

By Mayo D. Hersey

This problem was taken up by the Bureau of Mines as a result of the oxygen explosion at the Jefferson Physical Laboratory of Harvard University , and other similar explosions , in order to supply technical information which would serve as a basis for safety precautions in the future . At the Harvard inquiry the fact was emphasized by the Massachusetts State Chemist , Mr. Walter M. Wedger , that we do not know the limiting pressures and temperatures above which compressed oxygen and lubricating oil are capable of spontaneous explosion . The problem is also of importance to the Army and Navy and to the Bureau of Mines in connection with the hazards incurred in the use of compressed and liquified gases in the repurification of helium. In fact , the risk of fires and explosions due to traces of lubricating oil coming into contact with high pressure oxygen is of serious interest to all concerned with the manufacture and use of oxygen , a commodity which is now being produced and distributed on a rapidly increasing scale . Part of the money expended on this investigation was from Army and Navy funds . The problem was undertaken by the Bureau of Mines at the suggestion of Dr. Charles E. Munroe , Chairman of the Committee on Explosives Investigations of the National Research Council , and referred to the Pittsburgh experiment station of the bureau.

Jul 1, 1923

By Graham W. Marks, Betsy M. Jones

"Recently4/ it was shown that the total energy method5/ of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing this work, the present report deals with analyses for beryllium, zinc, cadmium, and indium.There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved.As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is associated with zinc and cadmium in zinc ores.The authors wish to acknowledge the valuable assistance of the staff of the Bureau of Mines Analytical Laboratory who made the chemical analyses and supplied the ore samples used in this work.A brief description of the procedures followed in making the standard curves and analyses is given below; a detailed discussion will be found in an earlier paper.6/Basically, the procedure for determining a standard curve consists of two parts: (1) Choosing a suitable line in the spectrum of the element to be determined and (2) determining the variation in the intensity of this line with the amount of the element burned in the arc."

Nov 1, 1948

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By August J. Kwitowski

This Bureau of Mines report summarizes the development of a protective operator compartment for a new generation thin-seam mobile bridge carrier. The developed compartment is commercially available and is currently employed on approximately 15 bridge carriers used in the mining industry. The design of the compartment, which employed human factors engineering and small- and full-scale mockup models, is fully described. Details of the compartment's fabrication, evaluation, and demonstration in a commercial low-seam coal mine are also provided.

Jan 1, 1986

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains-- maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

A general description of investigative work conducted by the Bureau of Mines at the, Missouri Valley. manganese deposits and leading to tonnage and grade estimates has been given in Report of Investigations 4375, part 1 of a three-part report of work done between July 1945 and August 1947. Basic factual information from which tonnage and grade estimates were drawn was derived through the drilling sampling of 238 large-diameter bucket-drill holes in 11 widely separated areas. Drilling areas were selected after careful reconnaissance, mapping, and consideration of earlier work done on the deposits by the Bureau of Mines, State agencies, and private organizations and individuals. Stratigraphic studies permitted extending the results compiled within the drilling; areas to outcrop and lightly covered manganiferous zones between an beyond drilling areas. The locations of drilling areas, drilling sections, and individual drill hues are shown on illustrations in part 1 f this report. The individual drill holes, aside from providing the basic information for tonnage and grade estimates, disclosed features affecting any future plan As exploitation. It in particularly significant that a large part of the visible outcrops is faulted end otherwise complicated by slides that give a false impression of the thickness, vertical location, and even the existence of manganese-bearing zones.

Jan 1, 1949

By William T. Boyd

Foreign mining publications describing successful hydraulic mining installations, and successful domestic hydraulic mining in a gilsonite bed, have prompted the Federal Bureau of Mines to conduct a literature survey of foreign publications to determine if the hydraulic mining method can be applied to domestic coal mining. Most foreign publications do not give detailed data about the water pressures, water capacities, and production and manpower requirements for successful hydraulic mining, However, they do provide enough general data on mining conditions, manpower, and equipment used to show that conditions in many bituminous coal deposits in the United States may be favorable for economical coal extraction, using high-pressure water jets. Therefore, the Bureau proposes to conduct a field investigation to determine the most appropriate natural conditions, water pressures, and equipment for successful hydraulic mining of coal beds in the United States with variable dip, thickness, and hardness. In the past, technical personnel reviewing foreign mining reports assumed that a steeply pitching coal bed was necessary for successful hydraulic mining. Although the structure of the coal bed may be a factor in gaining assistance from overburden pressures or help in an integrated hydraulic mining and transportation system, the coal is broken mainly by the action of high-pressure, water-penetrating cracks, fissures, or cleats; therefore, the slope of the coal bed is not necessarily a determining factor in hydraulic mining.

Jan 1, 1959

By R. B. Anderson

SULFUR poisoning of iron catalysts in the Fischer-Tropsch synthesis was investigated at the Bureau of Mines, because synthesis gas produced from coal contains sulfur compounds. Tests of two typical iron catalysts with synthesis gas containing known concentrations of H2S were made to determine catalyst life as a function of sulfur concentration to ascertain the type of gas purification required. Fixed beds of activated steel turnings and a fused iron oxide catalyst were investigated in sulfur poisoning tests at 21.4 atmospheres with IH2+100 gas containing 6.9, 23, or 69 mg S as H2S per cubic meter (0.3, 1.0, and 3.0 gr per 100 cu. ft.). In tests of reduced catalysts at constant temperatures, more than 80 percent of the activity was lost when 0.5 mg S/g Fe was introduced. Poisoning of nitrided or carbided fused iron oxide catalysts to a given extent required more than twice as much sulfur than for the corresponding reduced catalyst. When the synthesis temperature was increased to compensate for loss in activity, tests of the fused iron oxide catalysts at constant productivity could be continued for 19 to 98 days. The tests were terminated by clogging of the reactor, presumably caused by carbon deposition. One objective of the present work was to determine if synthesis gas, purified by the Bureau of Mines' hot-potassium carbonate process for removing H2S, OOS, and CO2, is suitable for synthesis on iron catalysts. The sulfur content of the gas purified by tills process is in the range of concentrations used in the present work. In constant-productivity tests of nitrided fused iron oxide catalysts with synthesis gas containing 6.9 mg S/m3, catalyst lives are nearly long enough for serious consideration of tills mode of operation. However, factors relating to selectivity and stability of the catalyst indicate that this type of operation is impractical for a commercial process. On this basis additional gas purification, such as iron oxide boxes following a hot potassium carbonate scrubber, is desirable.

Jan 1, 1965

By McMillan W. D.

Vermiculite is the name of a group of micaceous minerals characterized by their property of exfoliating when heated and thereby increasing many times their original volume. The resulting product has excellent heat-and sound-insulating properties, is used as a lightweight aggregate, and has numerous other industrial applications. Deposits of vermiculite occur in areas of pre-Cambrian rocks of the Llano uplift of central Texas, particularly in Burnet and Llano Counties. Because of the growing economic importance of vermiculite products, the Bureau of Mines undertook a detailed investigation of several deposits in Llano County. This investigation was completed in February 1947. The work comprised topographic surveys of five deposits, drilling with a 4-1/4 inch Parmanco power auger drill, and laboratory evaluation of samples. 342 drill holes, aggregating 4,905.5 feet, were completed, and 377 samples were taken. Laboratory evaluation of the vermiculite comprised expansion tests on both crude and beneficiated samples. The products obtained were compared with commercial-grade vermiculite from Montana.

Jan 1, 1949

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains--maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By Floyd R. Anderson

Noise control of existing pneumatic drills is difficult and runs into cost, performance and weight penalties. A need exists for a start-from-scratch approach for quiet pneumatic rock drills. The designs based on Leavell Principles which has been successfully used in demonstrating a quiet and vibration free paving breaker, is the concept chosen here. This report shows the feasibility of a quiet stoper for drilling roof bolt holes in coal mines. The work is directly applicable to pneumatic percussive rock drills. The report shows an oscillator based on patented Leavell concepts which results in a vibration free tool and noiseless exhaust. Dynamics of the oscilator is analyzed. Independant rotation of drill rod is provided by an air motor (screw expander) and flushing of cuttings is accomplished by an air ejector in a compact lower housing. The feasibility of no exhaust noise, low drill machine noise, and vibration free casing is discussed.

Jan 1, 1977

The original manuscript of section 2 of this series of miners' circulars devoted to accident prevention in bituminous-coal mines was completed in September 1944. At that time roof bolting had been tried with some success in the lead-mining district of south-eastern Missouri, but information on the subject was so fragmentary that it was not included as a method of roof support. References to roof support in bituminous-coal mines, therefore, were confined almost entirely to conventional timbering methods. In 1947 the Bureau instituted a research program and intensive study of the general problem of roof control, which emphasized roof-bolt application. The rapid increase in mechanized mining following the close of World War II provided the impetus for the Bureau's roof-control investigations, because the vertical supports used with conventional timber restricted the maneuverability of mechanical face equipment, and the industry wanted to explore every possible method of eliminating interference with the production cycle to gain full advantage of mechanized mining. Moreover, the accidental dislodgment of vertical supports greatly increased the roof-fall hazard. As roof falls have killed and seriously injured more mine workmen every year than any other cause or classification of injury since records have been kept, the Bureau assumed this investigative leadership with the prime objective of substantially reducing the annual toll from falls of roof, including falls of rib and face.

Jan 1, 1958

By E. R. Andersen, F. E. Block, T. T. Campbell

This work was done to develop methods for increasing the yields and purity of vanadium prepared by bomb reduction of vanadium compounds . Compounds reduced were V₂ 05 , V203 , VC , and VC13 . Sodium , calcium , and magnesium were used as reductants . Variables considered included reductant form , bomb size , pressure during reaction , method of ignition , and the use of slag fluidizing additives . It was concluded that yields of 85 to 90 percent can be effected by the calcium reduction of V205 in reactors measuring as much as 14 inches in diameter and 60 inches in height . Optimum charge composition included V₂05 , 65 percent excess calcium , and 0.4 moles sulfur per mole vanadium . Purity of the vanadium produced in large reactors varied from 99.5 to 99.8 percent . The higher purity metal , depending upon the amounts of interstitial impurities present , was usually cold ductile . Although high yields of up to 99.5 percent can be effected by bomb reduction of VC1 , the high pressures developed in the bombs and attack of the reactor walls by the byproduct chloride slags discourages this method of preparing vanadium . It was found that significant purification of impure regulus metal occurred when it was hydrided , crushed , acid leached , and vacuum dehydrided . Metal so treated can readily be converted to ductile sheet . A cost estimate based on the production of 100 tons of vanadium per year was prepared . It was concluded that pure ductile vanadium could be produced for approximately $ 20.00 per pound .

Jan 1, 1964

By Nicholas R. Dixon

This report summarizes all work performed under Phases I, II and III of U.S. Bureau of Mines Contract H0387006, "Development of a Prototype Retrofit Noise Control Treatment for Jumbo Drills." The noise and vibration levels of four jumbo drills were characterized and a survey of percussive rock drill usage is reported. A Gardner-Denver DH 123 drill was chosen as a demonstration drill, and extensive noise diagnostic studies were performed. Noise control treatments were designed, developed and evaluated in a reverberant drill test facility. The treatments consisted of an integral enclosure/muffler for the drifter, vibration isolation of the drifter from the enclosure and feed, and a drill steel sheath. A 19 dBA reduction in overall sound power level was achieved with no loss in drilling rate. The prototype retrofit treatments were field tested in an aboveground mine and in a production section of an underground zinc mine. Long-term durability and operator acceptance of the enclosure/muffler treatment were excellent. Preliminary evaluation of the drill steel sheath was encouraging, although additional testing is required.

Jan 1, 1982