Search Documents

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By R. A. Beall

Consumable-electrode arc melting is now accepted throughout the industry as the best method for producing ingots of zirconium, titanium, molybdenum, and their alloys. In addition, the technique is widely used in laboratories for fusing samples of such metals as hafnium, chromium, tantalum, columbium, and thorium. The production of consumable electrodes from these metals presents some rather difficult problems, the accepted industrial solution being the use of heavy powder-metallurgy-type presses. This paper summarizes information on fabrication of consumable electrodes by this and alternative means, such as sintering, nippling, and welding lightly pressed compacts of scrap metal. A possible saving of considerable capital investment is shown in the case of sintered compacts. The electrical circuit components of a pilot sintering unit are analyzed. INTRODUCTION The consumable-electrode arc-melting process has been accepted by most of the industry as the best method at present for producing high-quality pure or alloy in-got from sponge titanium or zirconium. This technique is not particularly new, having been patented by Von Bolton (l)3/ in 1909 for melting tantalum. However, it has been applied to industrial-scale operation only in the last few years. Among the important contributions to this technique are the work of Kroll (2) and Parke and Ham (3) and the work reported by the Office of Naval Research (4). The Bureau of Mines-has added considerably to the knowledge of this process (5-9).

Jan 1, 1956

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

This study assesses whether Narragansett Basin coal deposits could be developed commercially in the near future. To do this, we identify the potential market for the coal, assess the price these users would be willing to pay for Narragansett coal, and this price to the expected costs of producing Narragansett coal. The study concludes that the major market, New England utilities, could burn bituminous coal from Pennsylvania or West Virginia at a lower total cost than Narragansett Basin coal, assuming expected mining conditions and emission policies. Therefore, the study concludes that Narragansett Basin coal resources could not be developed economically in the next ten years.

Jan 1, 1979

The development of an onboard contaminant diagnostic monitor to continuously measure contaminant level in a mining machine was advanced to a prototype stage in this contract. Several concepts were investigated and it was found that a static spool type sensor was the most reliable and accurate. Laboratory and field tests showed that an instrument based on this concept is capable of measuring contaminant levels and/or size distribution, depending on the configuration of the sensor. Moreover, this instrument can function on emulsions or homogeneous fluids. Current laboratory equipment can operate on homogeneous fluids only.

Jan 1, 1983

By Walter B. Lenhart

This paper is one of a series on milling methods and costs being. published by the Bureau of Mines. The milling practices and special problems relating to grinding, tailings disposal, and choice of a treatment process at the Cardinal mill are discussed. The property of the Cardinal Gold Mining Co. is about 18 miles southwest of the town of Bishop, Inyo County, Calif., at an altitude of approximately 8,500 feet. The camp has been designated Bishop Creek by the postal authorities. The property comprises 33 mining claims, including fractions and millsite in sections 19, 20, 29, and 30, T. 8 S., R. 31 E. These claims are located in a general way along the strike of a band of quartzite.

Jan 1, 1938

By Eugene T. Sheridan

The 24th annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, revealed that 76 producers in 20 States reported commercial production of peat in 1957. In addition to the States that reported production in 1956, Colorado, Idaho, and Wisconsin produced peat in 1957 Forty-four producers reported humus production; 21, reed-sedge peat; and 22, moss peat production. This total exceeds the number of active plants but several producers recovered more than one type of peat. Fifty percent of the total production was reported as reed-sedge peat, 36 percent as humus, and 14 percent as moss peat. About one-sixth of the total production was raw peat, with no preparation other than being air-dried. The remainder consisted of processed peat prepared for use by cultivation, shredding, and/or kiln drying.

Jan 1, 1958

By Jerry B. F. Champlin

The successful injection of liquids into subsurface permeable formations for production stimulation, storage, or waste disposal requires a rapid, precise, and accurate method of determining the permeability of porous solids. This report describes a method and apparatus, developed by the Bureau of Mines, that use the principle of specific-volume permeametry. Calibration of the apparatus over a wide range of permeabilities and standardization of several apparatus constants have eliminated many of the tedious calculations and problems of manipulation common to some other methods. Improvements in reproducibility and accuracy have resulted from reducing experimental measurements to one parameter--time. Specific permeabilities of reservoir rock samples are determined directly from a chart that relates elapsed time to a permeability equivalent to that determined by bubble-tube measurements.

Jan 1, 1962

This publication summarizes the research (in-house and contract projects) programmed by the Bureau of Mines for fiscal year 1985 (October 1, 1984-September 30, 1985) under its Health and Safety Technology Program. The objective of these projects is to provide an ordered and sequenced advance toward the Bureau's overall goal of providing the system technology required to create a more healthful and safer working environment for the Nation?s mining and minerals processing workers.

Jan 1, 1985

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for Zambia for the period from 1970 through 1981. The work done through the Bureau of' Mines, Minerals Availability Program, under Contract number J0225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) timber and lumber, 6) fuel, 7) powder and blasting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

By William W. Aljoe

This report summarizes the Bureau of Mines noise-control research program from 1972 to 1982. Each segment of the mining industry--under- ground coal, underground hardrock, surface mining, and processing plants--has different noise-control problems because of vast differences in working procedures, equipment, and workplace design. The Bureau has identified the most serious noise problems in each segment and has developed strategies for attacking these problems. This publication points out the need for noise control in the mining industry, discusses Federal regulations governing worker exposure to noise, and describes the Bureau's overall approach to mining noise- control research. It traces the history of noise overexposure in each segment of the mining industry and discusses the major noise sources. It provides detailed information on noise-control research efforts in the Bureau's major areas of emphasis, including the results of these efforts. Finally, the report discusses the Bureau's future role in research on mining noise control, emphasizing the need to expend more effort on long term in-house investigations into the noise problems that have been identified in past programs as the most serious ones.

Jan 1, 1985

By G. C. Branner

The bauxite diagram presented as figure 1 was developed to clarify, by graphic means, the theoretical chemical constituents of gibbsite-kaolinite-type bauxite for all possible proportions of these two minerals from pure gibbsite to pure kaolinite. The tables in the report reflect the same date. The diagram provides (1) a graphic representation of the relations of constituents with respect to a ill possible percentages of alumina and silica, (2) a basis for verifying the accuracy of analyses of gibbsite-kaolinite bauxite, and (3) a basis for estimating the type and proportion of alumina hydrate and/or silicate minerals that may be present in gibbsite-kaolinite-type bauxite. The diagram, with accompanying interpretations and use formulas, will be useful to those connected with the mining and processing of bauxite.

Jan 1, 1955

By Oliver Q. Leone

The effect of oxygen content in the anode metal on titanium electrorefining characteristics was studied. Increasing quantities of oxygen in the anode resulted in increased anode scale formation, decreased anode and cathode current efficiencies, lower titanium recovery efficiencies, and higher oxygen content of the cathode products. The titanium electrorefining process performed best when the anodes did not contain more than 0.5 percent oxygen, although anode dissolution was recorded for alloys containing up to 25 percent oxygen. Back emf affords a useful index of an alloy to electrorefining.

Jan 1, 1965

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By Barry L. Warner

This program involves testing to determine whether a fire hazard exists when the exposed wood surface area of timber in a mine passageway equals 40 percent of the surrounding strata surface, excluding the sill. Twelve full scale fire tests were conducted in a simulated mine passageways, using kerosene pan fires as the ignition source. The tests included three timber sizes, plus one test with roof lagging, two wood types, plus one test with treated timbers, and two ventilation air velocities. The results show air velocity to be an important factor in the occurrence of flame propagation, and that the 40 percent surface area ratio of wood to surrounding strata appears to b0. a valid criteria for fire safety at 150 fpm, but not at 350 fpm.

Jan 1, 1975

By Paul V. Mullins

Review and evaluation of all available data on the vapor pressure of car-bon dioxide at the ice point, including previously unpublished results obtained by the Bureau of Mines, are presented. Suggested corrections and adjustments to all the data yield an average value of 26,136.4 mm mercury. Indicated agreement is within plus 1 part in 8,000 to minus 1 part in 11,000. A novel pressure bomb in which a sample of pure carbon dioxide is placed and sealed by a diaphragm fluid separator and its use as a reference pressure standard for extended and repeated use in the calibration of deadweight gages is described.

Jan 1, 1966

The Bureau of Mines in the Department of the Interior is increasingly concerned with the safety and health of personnel engaged in coal-mining operations, particularly below ground. The Bureau is also concerned with improving the utilization of domestic mineral resources, and reducing the environmental impact of mineral operations. One obvious way to improve safety and minimize health hazards would be to eliminate coal mining entirely by bringing the energy value of the coal to the surface in some other way, such as by partially burning it underground to form combustible gases and bringing these gases to the surface, where their energy content can be put to use. This technique might also improve the utilization of the coal resource. ? Accordingly, the Bureau of Mines, interested in re-evaluating underground coal gasification technology in terms of current and expected conditions in the United States, requested Arthur D. Little, Inc., (ADL) to appraise the technology to determine: ? Whether the current (1971) state of the technology offers a technically feasible method for gasifying coal underground that is applicable to the reserves of bituminous and lower rank coals in the United States. ? Whether a program of research and further development of the technology could ultimately make it a technically feasible alternative to current open-pit and underground coal mining operations. ? What the nature and cost of further research and development work in the technology should be.

Jan 1, 1971

By Pakalnis Rimas, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975