Search Documents

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By Lee Wehner, Daryl Kin, John Bolger

The Maumee Quarry, located in the city of Maumee, Ohio, has large in-situ cavities, ranging in size from 3 ft (.91 m) in diameter to over 15 ft (4.5 m). The drill/blast team challenge is to drill, load and shoot the geologically disturbed rock in a safe, cost efficient manner, while in close proximity to a commercial area. A continuous improvement process, managed by a Blast Optimization Team (BOT), was implemented to quantify the innovative explosive loading techniques that have been implemented. Borehole camera monitoring, modified loading practices, the need for accurate drill hole logging and open communications between the drill and blast crew proves critical to the success of the operation. Safe Standard Operating Procedures (SSOPs) have been developed and are strictly enforced for the drill/blast cycle. All blasts are monitored with seismographs and recorded on video to provide detailed information as part of the Blast Management Plan. Despite the geological challenges, the measurement of rock fragmentation index versus loader dig rates has provided near optimal crusher throughput.

Jan 1, 2007

By Claude Cunningham

AEL’s Electronic Delay Detonators are in routine use and growing in both volume and breadth of application in Africa. This trend will continue and grow internationally owing to increasing pressure on rockbreaking operations to conform to sustainable development principles. A fundamental breakthrough has been achieved, bringing production blasting into line with technologies, which leverage performance through tight monitoring and control. When moving from pyrotechnic systems, benefits are normally realized without having to adopt different timing patterns, but significant additional benefits are realisable by using the flexibility and precision of the electronic units to enter windows of timing previously closed. The higher price and increased care needed are a worthwhile investment, enabling operations to cross the chasm to stronger revenues, but the system must be robust and suited to the application and personnel. Economic models are vital for keeping track of the potential and achieved benefits of these systems. Some resistance can be expected from those who stand to lose income as a result of the improved efficiencies.

Jan 1, 2004

By David Siskind, Mark Stagg

Vibrations from Dade County (Miami area) quarry blasting and structure responses were measured at 11 locations between February and April, 2000, and 10 homes were inspected to analyze the characteristics of their cracking and other damages. These results were combined with information collected by the County and other studies done in south Florida for a blasting impact assessment specific to this area. In addition over 40 quarry blasts in the nine-week monitoring period, about 800 measurements were available from previous monitoring in Dade and neighboring Broward counties. An overall worst-case analyses based on the highest individual amplitudes suggested that vibrations in some areas could have been as high as 0.35 in/s. While amplitudes in the study period were below this value, they were found to be relatively high for the distances and charge sizes. Attenuation with distance is less in Dade County than found elsewhere with quarries having to use scaled distances several times higher than similar sites in the north. Consequently, the vibrations are perceptible at very large distances.

Jan 1, 2001

By U. Prasad

This paper summarizes the investigation carried out on a wide range of rock types, subjected to high velocity impact to simulate explosive action. A Split- Hopkinson Bar apparatus was used to generate the high velocity impact. The rock samples included both homogeneous and isotropic, and anisotropic types. The strain rate achieved was between 600 and 12OO/sec, The respective measured dynamic compressive strengths were compared with their low strain-rate or static values. It was found that the ratio of the dynamic to static values ranged between 2.5 and 4.6. It was also determined that the high strain-rate loading produced finer fragment size distribution than the static loading. The fragment size distribution from the two strain-rate regimes has been further analyzed to establish correlation with rock types and the strength characteristics. The results also confirm that high strain-rate loading (i.e. high detonation pressure and high velocity of detonation in an explosive column) would significantly affect the degree of fineness in a blast.

Jan 1, 2001

By Daniel Haines, Benjamin Konshak, Michelle Crull

American Technologies Incorporated Group (ATI) is the prime contractor with U.S. Army Corps of Engineers, Huntsville Center (CEHNC) in the Honolulu District for the removal of munitions and explosives of concern (MEC) at the Former Waikoloa Maneuver Area. The site is approximately 123,000 acres on the Big Island of Hawaii, which was used as an artillery firing range with live ammunition and other explosives deployed. ATI utilizes state of the art metal detection equipment to find and excavate metallic anomalies that have hazard potential. Both the investigation and disposal procedures present challenges due to residential communities and archeological sites that are located in and around the site. In order to excavate metallic anomalies safely and without adverse impact, ATI utilizes CEHNC-designed, open front barricades constructed of sandwiched sheets of aluminum with a support structure. When munitions or explosives are located, ATI is responsible for safe disposal using shape charge perforators to detonate the item where found. Sandbags are used for mitigating the effects of all detonations.

Jan 1, 2008

By TA Louw, Dr CM Lownds

In an era where profits are constantly being eroded, mines are looking towards technology developments to assist them in solving mining problems and reducing mining costs. An emerging technology that could assist mines in becoming more cost effective is electronic detonators. Electronic detonators have been under development for several years. Over the past three years, the spotlight has fallen on commercial use of electronic detonators and the extent to which the promise of precise and programmable timing can assist mines with their environmental and productivity problems. This paper uses case studies to demonstrate both surface and underground applications where electronic detonators and blasting systems were used to solve typical mining problems such as vibration and fragmentation. Safety aspects such as hanging wall conditions and high wall stability also benefited from the use of electronic detonators. The paper also demonstrates how the use of accurate electronic detonators and blasting systems has resulted in improved/more even fragmentation with further downstream efficiencies. These efficiencies may include increased cast percentages, reduced oversized rocks, quicker cleaning times and increased production rates.

Jan 1, 2004

By Neal Lee, Braden Lusk, John Silva Castro

One of the most common assumptions regarding the use of ANFO versus utilizing 100% sensitized emulsion is that ANFO “turns over” the muck-pile better, due to the “higher gas volume” supposedly inherent in ANFO. This paper examines this assumption and provides quantitative data for analysis. Total gas volume from each product was evaluated using Orica’s I.D.E.X. Code analysis. This analysis was used to determine if gas volume is a significant contributor to differences in fragmentation and movement between blasts utilizing the two different products. A constant drilling and blasting cost per yard for given cut depth, hole diameter, stemming height and rock type was utilized. The cost per yard was held constant by adjusting patterns considering product, accessory, and drilling costs. Photographic fragmentation analysis, dig rates measured quantitatively through production tracking and time studies and qualitative information about the diggability of the blast provided through video recordings were used to evaluate performance. The data collected during the study is presented and recommendations are made regarding the performance of ANFO and Emulsion holding other variables constant for a limited number of blasts.

Jan 1, 2012

By Harry Verakis, Thomas Lobb

This paper summarizes the course of mine blasting safety, particularly in underground coal mining, in the USA for over a century of mining operations. During the late 1800's and especially in the first decade of the 1900's, a large number of mine explosions occurred in which blasting played a significant role. A contributor to the large number of mine explosions during this time period was the use of black blasting powder to extract coal and other minerals. A review is made of some of the more significant underground coal mine explosions that resulted from blasting operations during this time period up to the present day. The safety measures that were adopted and required by a series of laws as a result of mine explosion disasters in which blasting was one of the factors are examined. The time line of historical improvements in blasting safety and the tremendous reduction in fatalities and injuries over a century is illustrated and discussed. The improvements, which included the elimination of black powder and dynamite and the introduction of safer explosives termed "permissibles" occurred slowly over time and culminated from the occurrence of many coal mine explosion disasters. The blasting accident history over the past decade is discussed to show the great gains made when compared to the first decade of the 1900's. The most recent blasting accident fatality that occurred in October 2006 at a U.S. underground coal mine is also discussed. Although the blasting accident record is significantly improved from over a century ago, continual improvement is needed to reach the goal of zero fatalities.

Jan 1, 2009

By Gungor Tuncer, Ali Kahriman, A. Kadir Karadogan, Savas Gorgun

The environmental problems arisen from ground vibration and air blast have been faced and discussed frequently in various industries such as mining, construction, quarry, pipe line etc. where blasting is unavoidable operation. Structural damage due to ground vibrations creates great socio-economic problems for mine and quarry management as well as for the people residing in its vicinity, therefore in bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. With the general trend towards larger blasts in mining and infrastructure excavation, ground vibration and air blast problems and complaints have significantly increased. With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision, therefore determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. In another word, prediction of ground vibration components is extremely important for the minimisation of the environmental complaints. Estimating of particle velocity and other components of ground vibration with reliable approaches will give important facilities to the blasters. Although many studies had been carried out to isolate environmental problems induced by blasting in the past, a general reliable formulae has not been established yet. Due to restrictions on the complexity of ground motion, blasting and test site factors, experimental studies are still necessary for each site to minimise environmental issues. This paper presents the results of ground vibration measurements carried out during the excavation activity for contruction of an organised industrial region located nearby Istanbul in Turkey. The major rock type is granite that is encountered at this site. Within the scope of this study, in order to predict peak particle velocity level and produce a site-specific propagation curve for this site, ground vibration components were measured for blast events during bench blast optimization studies over a long period. In blasting operations; ANFO (blasting agent), gelatine dynamite (priming) and delay detonators (firing) were used as explosives. While the parameters of scaled distance (charge quantity per delay and the distance between the shot and the station) were recorded carefully, the ground vibration components were measured by means of two different vibration monitors for every event. Then, the data pairs of scaled distance and particle velocity were analyzed. The equation of scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. At the end of statical analysis and evaluations an empirical relationship with good correlation was established between peak particle velocity and scale distance for this site.

Jan 1, 2000

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By Francisco Sena Leite, Vinicius Miranda

Mine blasting is directly associated with ground vibration. If these affect critical structures (buildings pit walls, etc.) they must be mitigated to reduce the environment and social impacts. Vibration monitoring and control is one of the most important procedures in blasting because it will impact short and long term incidents associated with this blast effect. Technology moves ever forward, and today we have personal devices that are equipped with an array of sensors, for that reason the authors decided to investigate the possibility of using a personal device to do vibration control. This case study compares the same blast measured with a traditional seismograph and a smartphone. To validate this new methodology, attenuation laws were built with data from a traditional seismograph and a smartphone application. Predictions were also made prior to a set of blasts. Residual analysis was used for data validation from the two different sources. From the performed analysis, to prove the validity of this new methodology, the normality tests for statistics residues analysis proves that it is possible to infer that the model has a null residual mean and a small residual error. The achieved results show the accuracy of these devices, the authors pretend to show the potential of this equipment and open a completely new door for vibration analysis.

Jan 1, 2018

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By Dale Preece, Stephen Chung, D. Scott Scovira

The DMC_BLAST (Distinct Motion Code) has been developed to model rock motion and displacement during the gas expansion phase after the detonation of an explosive in a borehole. Recently, a designated delay firing order algorithm was written into the DMC_BLAST code. The model can now be used to analyze rock mass displacement for a V-cut, center opening, or sinking cut initiation sequences. This new feature allows the investigation of the effects of delay firing order on rock displacement when blasting complex inter-bedded and ore-waste structures. The model provides important ground movement and mixing indicators for dilution control in surface gold mining relative to the initiation sequences employed. Echelon blasts as compared to center opening type blasts show differences in their internal muckpile displacement. These displacement differences can be important to operations that mine narrow strike driven ore bodies. The model also has applications to through coal seam blasting and demonstrates that down-dip blasting is a better alternative than up-dip blasting. There is less disturbance to the dipping coal seam and less mixing of the rock and the coal.

Jan 1, 2000

By Elias Poulakidas, Marco Arellano

The impact of a higher copper price on the open pit metal mining sector has derived in a faster and safer way in which the mining operation of broken and mineralised material is carried out. In this regard, a good control of bench stability allows a lesser extra removal of material and so more safety to get the planned ore. The stability is ensured through an efficient drilling and blasting, applying the current technology and available know-how. An efficient use of energy through low-density explosives which are the most adequate for the existing solid rock releasing energy in a smoother way through a deterministic detonation sequence which is the application experience presented here. This application experience has two main technological factors; the adequate type of explosive for the kind of rock, in terms of velocity of propagation (Vp) together with the use of a determined detonation sequence and the appropriate designs, which allow to reduce the level of damage to the walls and to maintain a minor backbreaking through quantification with vibration modelling carried out at the near field. The reductions achieved were 30% lower in peak particle velocity.

Jan 1, 2008

By Quian Liu

Since the establishment of the CANMET Experimental Mine in Val d'Or, Quebec in 1991, research activities in rock fragmentation have been carried out not only in the underground laboratory but also in production mines in the north-west Quebec region. Among the instruments available for rock fragmentation, the Kodak EktaPro 1000 Motion Analyzer (also called the high speed video system) has been one of the most useful tools for monitoring blasts in both underground and open pit. This system is capable of recording events at rates from 50 to 12,000 frames per second (fps). The buffer memory has a capacity of storing 2050 images. To use this system in the underground, a steel box was made with a bullet-proof glass in the front to protect the camera. The processing and recording equipment are placed in an aluminum case which can be located about 30 m away from the camera via an extension cable. For each blast monitored, high frequency geophones and accelerometers were used to monitor ground vibrations and give a timing reference of the explosive detonations to correlate with the observation of the captured images.

Jan 1, 1994

By Rafael Tadeu Pinto e Moura, Giorgio De Tomi, Jacopo Seccatore

This paper describes a research and development project in an open-cast mine with the goal to achieve an average P80 of 300 mm (11,8”) in the run-of-mine (ROM) product without altering the existing budget. The project included several variables in the blast design that were not previously taken into account, such as the orientation of natural joint sets in the rock mass, specific energy of the explosive and firing sequence. The new blast design method considered the directions of natural joint sets and determined the drilling pattern and the firing sequence accordingly to favor the movement of the blasted rock along its preferential direction, to reduce its confinement. At the end of the project, it was achieved an average P80 of 304 mm (12”) in the ROM, 50% lower than the one at the beginning of the project. The final blast of the project showed a reduction of 3% of the drill and blast cost, employing the same powder factor and the same drill pattern size used at the beginning of the project. The results achieved show how rock fragmentation is related to variables that are not contemplated in the most common fragmentation models: the firing sequence and the direction of movement in the blast.

Jan 1, 2015

By Gregory Lorsbach, Wade Hutchison, Earnest Grigoryan

Comparing measurements from multiple seismographs, particularly when the instruments are deployed in a “side-by-side” situation, is often problematic. Measurements often differ by as much as a factor of two. These differences are attributed to issues related to calibration, geophone coupling, and differences in geology over very short distances. Unfortunately, these explanations are often purely qualitative, but are accepted as factual. Shake table testing often demonstrates that those seismographs that indicate large differences for a particular vibration event, may correlate within a few percent of each other and the known shake table input. Geophone coupling also does not fully explain the difference in measurements since geophones in side-by-side measurements are deployed identically. Differences in geology do not explain the difference in measurements since it would be unrealistic to expect significant differences in distances less than one meter in a normal monitoring situation. Utilizing a new technological approach to vibration measurement and analyzing numerous side-by-side measurements, it has become clear that a significant portion of the observed differences between seismograph measurements are instrumentation induced. This study examines and describes some of the most significant sources of the seismograph error budget.

Jan 1, 2005

By Richard J. Mainiero, T S. Bajpayee

The Bureau of Mines, U.S. Department of the Interior, has developed test procedures and criteria for evaluating explosive reactivity of explosive contaminated solid waste substances generated by U.S. Army Ammunition Plants. These substances are produced as explosive-contaminated sludge from waste water treatment plants, residues from the burning of munitions and explosives on open ground, and residues from deactivation furnaces. The characterization of explosive reactivity is a prerequisite for disposal of such waste materials, which may be contaminated with primary explosives, propellants, or pyrotechnic materials. The Bureau has proposed two tests for this purpose. These tests were developed to evaluate the explosive reactivity as defined in Title 40, Code of Federal Regulations, Part 261.23(a)(6) and (7). These are Bureau of Mines Gap and Bureau of Mines Internal Ignition tests, which determine the sensitivity to shock and thermal stimuli, respectively. This paper also includes gap and internal ignition reference data for typical blasting agents, high explosives, propellants, and marginally reactive substances. These reference data were used to establish test criteria. The Bureau has evaluated over 400 samples of contaminated soil, sludge, and burning residues using these two test methods.

Jan 1, 1988

By Ronald Joseph

Windows-based automated blast loading systems have long being conceptualised and never really taken off in the surface mining sector. However, with the introduction a windows-based automated blast loading and reporting system onto the Mobile Manufacturing Units (MMU’s) at Debswana Diamond Company operations in Botswana in August 2004, a project to automate blast loading (charging) and reporting ensued. This work was pioneered over three phases at Debswana’s Jwaneng Diamond Mine by African Explosives (Botswana) (Pty) Limited as part of the African Explosives Limited’s (AEL) integrated-mining (i-mining) concept. The first phase of the project involved the blast reporting system, at which time an average amount of explosives were loaded into all blastholes and all blast loading information was saved to a Microsoft Access 2000 database on the MMU computer. The second phase of the project, which ran until the end of the second quarter of 2008, involved manual blast plan loading and reporting system using flash disks, and the third phase which was installed and commissioned in the third quarter of 2008 and is currently operational at Debswana’s Jwaneng Mine, involves the automated blast loading and reporting system via Wireless Local Area Network (WLAN). This system is now routinely used to achieve operational and mining efficiency goals at the mine with respect to blasthole charging and blasting, and this paper briefly summarizes the status of this project at Jwaneng Diamond Mine where this technology is currently being monitored and also illustrates the positive mining impact that this innovation brings to the mining operation, both from an economic and efficiency perspective.

Jan 1, 2009