Search Documents

By Xubo Chen, Zhiqiang Hu, Zhijian Sun, Gaoyun Zhou

"The research aimed at developing an efficient and environmental frother,which was applied in the flotation of sulfide ores. The flotation properties of an efficient frother and pine oil have been studied relatively by flotation tests of lead and zinc sulfide ores. At the same time, the biodegradability of two kinds of frother has been studied by the method of biological respiratory curve. The test results show that the flotation properties of new frother are superior to pine oil such as flotation rate, dosage etc. and its biodegradability is superior to pine oil. INTRODUCTION Frother is a kind of important agent in flotation reagents.In practice, the criterion of the foaming performance of the frother is what is high and low according to flotation indexes. The difference of different minerals and flotation technologies has great influence on the foaming performance of frother, and it is very important to choose the corresponding frother. The type, dosage and selectivity of frother in flotation process must be considered carefully. In today's society, environmental protection and ecological protection are becoming more and more important, and the environmental and ecological damage from mine development has aroused increasingly more attention. The use of mine agents has promoted the development of mineral resources, greatly improves the recovering utilization of mineral resources, at the same time, the production and use of mine reagents also inevitably bring about pollution, and result some influence or damage in the ecological environment.The frother is a common kind of reagent in the flotation process of the concentrator. In many cases, the waste water in the concentrator can not be let out in the natural water because the higher content of the frother in the waste water results in higher index of COD.This will inevitably increase the cost of waste water treatment in the mine.Therefore, the choice of frother should not only consider its influence on the flotation index, but also consider its influence on environmental protection. Waste water treatment is a way to solve the waste water pollution, but it needs to cost a lot of fund, manpower and material resources.And the development of high efficiency pollution-free reagent is a good way to reduce the production cost of mining enterprises and reduce the environmental pollution."

Jan 1, 2018

By Shankar Narasimhan

Data Reconciliation is a technique that has been developed more than fifty years ago and has been refined over the past few decades and is now being deployed routinely in several process industries such as refining, petrochemicals, mineral processing and hydro-metallurgy. The main aim of data reconciliation is to obtain accurate estimates of all process variables and parameters using plant measurements that are invariably corrupted by random errors and may also contain biases and other gross errors. These reconciled estimates are subsequently used either in offline exercises such as simulation, retrofitting, and de-bottlenecking or in online optimization and control applications. In this presentation, a brief history of data reconciliation, its assumptions, and uses are reviewed. New developments in this area are highlighted such as robust data reconciliation to handle model uncertainties, and reconciliation using identified models derived purely from operating data. Several case studies in the mineral processing industries reported in the literature are also highlighted to indicate the potential benefits of this technique.

Sep 1, 2012

By Zhu Yangge, Zheng Guibing, Hu Xiaoxing

"Because of the similar crystal structure and surface properties, it is very difficult to realize the efficient separation of magnesite and dolomite by flotation, which is the main reason restricting the utilization of magnesite resources with dolomite symbiotic. To deal with a magnesite resources with high content of calcium impurity in northwest China, a novel decalcification technology by combining flotation with leaching is proposed in this paper. In flotation process, a novel flotation collector with good efficiency and low temperature resistance was developed, and the depression effect of sodium hexametaphosphate was investigated. In leaching process, the leaching rate difference of calcium and magnesium was observed. By industrial test, from the magnesite ore with MgO content of 43.96%,the grade and recovery of obtained concentrate ( calculated by MgO) are 47.28% and 67.68% respectively, at the same time, CaO content decreases from 3.91% to 0.30%, which means that more than 95% of CaO impurity is removed.INTRODUCTIONMagnesite is one of the main raw materials for the production of refractory materials, and it is widely used in metallurgy, chemicals, ceramic, construction and other industries. China is the most important supplier of highquality magnesite resources, accounting for about 60-70% of the world's identified supply of magnesite products is provide by China (Jewell, 2014). In recent years, high-quality magnesite ores can be directly used are going to run out in China, and the utilization of magnesite resources with high impurity content have drawn more attention.The main purpose of purification for magnesite is to remove SiO2 and CaO impurities which affects the strength of the refractory material. Flotation is the commonly used method to remove impurities in magnesite ore. Reverse flotation with cationic collector is usually adopted to remove silicon containing impurities, and a great deal of literature has been reported (Santana A. N. and Peres A. E. C., 2001; Wang and Sun, 2008; Zhu et al, 2014; Wu et al, 2015; Ivan B. et al, 2017). But when the major gangue component is dolomite, it is very difficult to realize the efficient separation due to the similar crystal structure and surface properties between magnesite and dolomite. To solve this problem, researches have studied the surface properties of magnesite and dolomite, such as wettability, electrical property, solubility and solution chemistry (Nermin and Nurgul, 2006; Nermin 2006; Ozbek and Abali, 1999; Lacin et al, 2005; Bayrak et al, 2006; Bakan et al, 2006; Chen G. and Tao D., 2004), but the commonly studied direct flotation using oleic acid as collector is still hard to receive an ideal effect."

Jan 1, 2018

By L. Tavares

The significant capital and operating expenditure of size reduction operations have maintained comminution on the spotlight of mineral processing research during the last century and, more recently, the concerns about the impact of these operations on the sustainability of the minerals industry, will remain to do so in the 21st century. One of the most popular approaches that have been used to deal with these challenges is the application of simulation both to reduce the uncertainty in the design and improve the operation of size reduction operations. From the initially purely empirical approaches, including the energy size reduction ?laws? and the phenomenological approaches, of which the traditional population balance model is, arguably, the best example, comminution modeling now reached a point in which more fundamental and mechanistic models are sought. The paper analyzes some of the advances that now make multiscale modeling of comminution processes realizable. On the microscale, greater understanding of the phenomena involved in fracture and fragmentation of single particles under different stressing conditions now exists. Particle breakage testing methods are currently used in a routine basis by industry and good quantitative descriptions of different breakage mechanisms are now available, although research is still required to develop appropriate models for a couple of them. On the macroscale phenomena, the discrete element method (DEM) has been successfully used not only to provide insights but also quantitative information on the transfer of mechanical energy from the machine to the grinding media in mills and to particles in crushers, while smoothed particle hydrodynamics (SPH) and computational fluid dynamics (CFD) to describe fluid flow. The paper also analyzes the importance of modeling mesoscale phenomena in size reduction, which is the interaction of particles forming assemblies or beds of particles, demonstrating some of the areas requiring further attention. Examples of application of the multiscale modeling approach to the inadvertent comminution of ore lumps during handling, to the comminution in vertical impact crushers and tumbling mills are demonstrated. Keywords: comminution modeling, DEM, SPH, CFD, multiscale modeling approach

Sep 1, 2012

By V. A. Chanturiya

The application of High-Power Nanosecond Electromagnetic Pulses (HPEMP) irradiation in dressing of resistant gold- containing ores appears attractive as this technique provides for a significant increase in precious metal recovery (30-80% for gold and 20-50% for silver), therewith helping reduce both energy consumption and the cost of products. The prospects for applying pulsed power technologies in the mineral processing in order to increase the contrast between the flotation properties of raw minerals dictate the need to perform special studies of the effect of HPEMP on the structural state, phase composition, and physical and chemical properties of surfaces of sulfide minerals as the main carriers of precious metals. This study deals with plausible mechanisms of the micro- and nanophases formation on the surfaces of sulfide minerals under the effect of high-power nanosecond electromagnetic pulses (HPEMP) with high electric field strength ~107 V/m. This paper discusses reasons for the changing of flotation behavior of natural pyrite and arsenopyrite during the pulsed-power treatment. It was concluded that HPEMP treatment may be regarded as a tool to change the surface composition and sorption ability of collector (xanthate) onto mineral surface, and, therefore, it allows to control the hydrophobic-hydrophilic surface balance. Single mineral flotation tests have been shown the significant increasing of the pyrite recovery while the arsenopyrite was depressed. The results of gold containing pyrite (pyrrhotite)-arsenopyrite ore flotation in batch approve the decreasing of arsenic recovery in sulfide concentrate. Keywords: pyrite, arsenopyrite, high power nanosecond pulses, activation, selective flotation

Sep 1, 2012

By David De Klerk, Maximilian Richter, Thirunavukkarasu Pathmathas, Indresan Govender

We consider the average power dissipation distribution for dense granular flows of an idealised mono-sized charge (5 mm glass beads) in a 300 mm diameter tumbling mill operated in the cascading-to-cataracting Froude regime. By combining the inherent frictional nature of particles within a dense flow regime and noting that tumbling mills are typically characterised by collisional and turbulent stresses, we derive the power dissipation distribution for athermal boundary conditions. The input data to the model (velocity, solids concentration, pressure and flow depth) are obtained directly from non-invasive measurement using a nuclear imaging technique: Positron Emission Particle tracking (PEPT). The power dissipation due shear stresses is shown to be the dominant mode of dissipation in the tumbling mill with up to two orders of magnitude difference between pressure induced dissipation and shear.

Jan 1, 2014

By Sami Makni, Ahmed Bouajila

"To remain competitive in an open market, mining companies are more and more requested to optimise their complex and highly multivariate processes. The increasing amount of process data, brought about by intensive use of instrumentation and the progress in computer data acquisition, enhances the need for more and more powerful and robust tools for the analysis and modelling of the process data. Now, with the emergence of multivariate data analysis (MDA) techniques, on-line clustering of mineral process behaviour is possible and could help in the extraction of valuable process operation indicators. MDA can be used in different mineral processes such as flotation, grinding, smelting etc.In this paper, we focus on grinding process considered as the most costly and power consuming node of the mineral processing scheme. Different objective-oriented levels of data clustering will be addressed.First, the evaluation of grinding operation taking into account data and constraints from all processes before (e.g. blasting, crushing) and after (e.g. flotation, leaching, etc.) the grinding node. The second level deals with process diagnosis by differentiating operation level and identifying behaviour drifts. Control and optimisation are two other levels concerned here with the selection of optimum trajectories in the drift correct.Industrial plant data are processed in order to illustrate the feasibility and the potentiality of MDA applications in addressing the clustering and interpretation of grinding mill behaviour."

Jan 1, 2003

By Wenying Liu, Marek Pawlik

Long-chain ionic surfactants, with fatty acids and amines as the most important representatives, are widely used as collectors in froth flotation. These surfactants, generally referred to as weak electrolyte collectors, frequently form solid insoluble precipitates within a certain pH range. However, the action and behavior of these colloidal precipitates in froth flotation systems are not well understood and has not been well decoupled from those of dissolved forms. The objective of this study was to understand and compare the role of colloidal precipitates with that of the dissolved forms at gas-liquid and gas-liquid-solid interfaces. Using primary amine as the model surfactant, experiments were carried out to measure: the maximum volume of bubbles generated in the presence of dissolved and precipitated forms of the surfactant; surface tension for both forms of the surfactant using the drop shape and maximum bubble pressure methods; and contact angle using the sessile drop method. The experimental results showed that: in the presence of the precipitate, bubble volume was smaller, which was correlated with the lower surface tension and higher contact angle measured; the surface tension of solutions containing surfactant precipitate was affected by the surface age of liquid droplets. This study enhances understanding of the interfacial behavior of long-chain ionic surfactants under different conditions, which would help improve the efficiency of reagent utilization in froth flotation.

Jan 1, 2014

By C. R. Mambote

One of the processes developed for vanadium recovery from the fly ash of crude oil is through acid leaching. In the process, iron is one of the impurities that should be removed before vanadium precipitation, due to the fact that iron tends to co-precipitate with vanadium. The mechanism of iron precipitation is understood in terms of ferric hydrolysis, followed by the dimerization and subsequent polymerization of the crystalline iron compound. In order to develop a new approach for the fly ash processing, in the present paper the precipitation of iron from the liquor after the leaching process was studied with addition of NaOH or NH4OH in the presence of H2O2 or Na2C2O4 at 80°C. The objective was to investigate the feasibility of the selective precipitation which could be applied to vanadium and nickel recovery from the fly ash. The experimental results show the difficulties of removing iron by precipitation without co-precipitating nickel and vanadium.

Jan 1, 2014

Due to complex mineralogical and chemical interactions of the value and gangue mineral phases present in uranium-containing lateritic ores, deleterious pulp gelation which impacts on value metal recovery sometimes occur during atmospheric leaching. In this study, the leaching behavior and particle interactions of selected oxide (hematite, quartz) and clay minerals (muscovite, chlorite), which constitute predominant host gangue phases of typical lateritic uranium ores are investigated to provide basic, mechanistic understanding of temporal pulp gelation phenomenon. Isothermal, batch leaching with H2SO4 was carried out on concentrated dispersions (30 ? 57 wt.%) of single minerals at pH 1 and 25 or 70 °C and their concomitant solution, speciation and rheology (shear yield stress, viscosity) were characterized. It is clearly shown that despite the high oxide content of lateritic ores, the pulp chemistry and rheology is largely affected by the incongruent leaching behavior of more reactive, acid-consuming aluminosilicate clays. Furthermore, time- and temperature-dependent alumino-silicate species polycondensation interfacial reactions are shown to be responsible for the enhanced particle interactions, reflecting strong pulp rheology in agitation and pumping. If not properly mitigated, high pulp shear yield stress and viscosity have a striking impact on processability and hence, value metal recovery.

Sep 1, 2012

By C. Y. Jia

Adsorption of Thiooxidans ferrooxidans and Mycobacterium Phlei on the surface of pyrite and galena was studied. From the experimental results, it was observed that Mycobacterium Phlei adsorbed preferentially on pyrite than on galena at neutral and alkaline pH values, while Thiooxidans ferrooxidans is not at all pH range, and the scanning electron microscopy photograph also indicated that. FTIR and XPS of two strains of bacteria indicated that there are much functional groups on surface of them, such as O?H, N?H, C-O, C?N, C?O etc, but S-O group occurred on Thioox-idans ferrooxidans cell surface and the P-O group appeared on Mycobacterium Phlei cell surface, and the content of C?O?H and C?O?C groups on Mycobacterium Phlei cell surface is higher than that on Thiooxidans ferrooxidans cell surface, this also been known from UVS investigation. The affinity of these groups to metal ions on sulfide minerals is able to explain the selective adsorption.

Jan 1, 2014

By Filippov. L. O.

Metallurgical results for the copper-nickel disseminated ores were improved by using ultrasonic treatment. This has been demonstrated by processing of bubble-pulp flow in the reactor zone of a reactor-separator flotation machine. It can be explained by changes in mineral and size composition of the concentrates. Thus, the selectivity of Cu/Ni flotation for different values of the hydrodynamic parameter increases considerably. Additional effect of the ultrasound treatment has been noticed under conditions when the detachment of the gangue minerals from bubbles can be controlled. Reactor-separator has advantages over other types of flotation cells for this purpose. In fact, the weak diameter of reactors make more efficient the ultrasound effect than in conventional impeller or column flotation machines. A combination of ultrasonic treatment with original organization of gas pulp flux in the reactor-separator allows to obtain significant effects in the flotation attachment/detachment subprocesses, enhancing the process selectivity and/or recovery of substances. Increase of total recovery of copper and nickel into bulk concentrate at constant grade is 8.5% for coarse disseminated ores. For copper ore, copper recovery increased by 10% at unchanged grade of 11.7% and nickel recovery gained 17% at the constant grade of 2%.

Sep 1, 2012

By Y. C. Liu

Ningxiang-type iron deposit is a most important sedimentary oolitic hematite deposit in China. Its? detected ore reserves are 3.72 billion tons, which is 73.5% of all detected reserves, and there are about 10 billion tons of prognostic resources. It is considered as the ?poor mine? for a long time be-cause of its difficult prooerty. But based on the ore characteristics of different deposits, the technological characteristics of ore are different with great diversity in ore baring horizon, distribution range, deposit scale, ore petrology, ore mineral assemblage and iron content. Through the study of deposit features and technological mineralogy of different Ningxiang-type of iron deposits in China, and based on industrial types and natural types of ore deposits, we divide different technological types according the technological features of the ore such as mineral composition, particle size, dissemination, occurrence of useful elements and harmful elements, the main physical and chemical properties of mineral and geological conditions of deposits, etc, moreover, propose the different utilization, mineral processing technologies and product schemes for the different types of ore.

Jan 1, 2014

By A. V. Kanarskay?

The research is aimed at involving in the processing of poor platinummetal natural and technogenic raw materials. The purpose of the research is the creation of a multifactorial complex of innovations in the system of ore preparation and separation cycles, which ensure a high efficiency of flotation enrichment of hard-to-treat raw materials. In the usual practice of enrichment, minerals of the platinum group (PGM) of less than 10 microns in size are the source of inevitable process losses. For poor raw materials, it is precisely thin PGMs that are characteristic, their proportion sometimes being almost 100%, and their opening leads to the formation of a large amount of slime, which adversely affects the efficiency of flotation. To reduce the yield of slimes and increase the selectivity degree of the opening of the PGM in the ore preparation cycle, a dry grinding scheme and pneumoclassification of the milling material has been developed to obtain fractions of different fineness, density and morphology of the particles. From 2 to 5-fold reduction in the yield of slurries for various ores has been achieved. The separation cycle successfully tested are: flotation of fractions in separate cycles with a differentiated choice of the reagent regime; preliminary selective flocculation of slime fraction material; use of a new generation of bioreagents for flocculation and flotation. A new approach to subsoil research is protected by a patent. The dependence of the efficiency of biocollectors on the composition of biomineral extract from the processed raw materials, which forms the basis of new reagents, is established. The possibility of obtaining the degree of extraction of PGM, native gold and sulphides from finely ground pre-fractionated poor ores with the use of biocollectors of at least 85% is proved. With conventional reagents, the extraction of PGM is 12-23% lower, with the use of traditional ore-preparation apparatuses, the PGM recovery rate was halved. Methods for the long-term storage and preparation in industrial conditions of biocollector reagents that do not require the purification of waste waters from them have been developed. The developed multifactorial system of intensification of flotation enrichment can be introduced to recovery PGM from tailings of enrichment of titanomagnetite, chromite and copper-nickel ores.

Jan 1, 2018

By Brian Hart, Liuyin Xia, Staman Dimov

The recovery of rare earth elements (REE) is fast becoming of significant interest globally. Modern research and development programs (outside China) towards the optimization of REE mineral recovery by flotation have been lacking. Due to the mineralogical nature of many hosting deposits, the separation and recovery flotation flowsheets can be very complex. As part of a research project, a selected suite of hydroxamic acid collectors (Naphthoyl, Cyclohexyl, Benzoyl, Octyl, Terta-butyl benzoyl, Salicylic) were tested in order to examine their potential for recovery and selectivity. Micro flotation tests were conducted on a feed sample, recovery and grade of the products were used to evaluate their relative flotation efficiency and selectivity and these results (flotation with the hydroxamate collectors) were compared to a phosphoric acid/sulphonate collector mix(shorten as "mixed"). In the testing, the flotation response with the hydroxamate collectors was significantly better than the "mixed" collectors on freshly ground (no slimes removed) samples. Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the "mixed" reagents. Product assays show that recovery of both La and Ce is significantly better for using the salicylic hydroxamate and that Nb, Y and Zr recovery are favored by using octyl hydroxamate. These results indicate mineral flotation selectivity could be achieved by using selective hydroxamtes. Spectral fingerprinting by TOF-SIMS surface analysis has allowed for the identification of reagent species. TOF-SIMS surface analyses of grains analysis confirmed that REE bearing grains reporting to the concentrates are doing so in response to collector attachment whereas grains reporting to the tails are doing so in response to a lack of collector. The TOF-SIMS surface data bas been used to examine the factors promoting flotation stream partitioning.

Jan 1, 2014

By Ventsislav Stoilov, Angel Angelov, Ivan Korolev, Antti Remes, Todor Pukov, Stoyan Gaydardzhiev

"The process modeling and simulation studies aim for better process operation and favorable environmental impact. The objective of this work is to set up a simulation model of the Assarel copper flotation circuit for planning and optimization of the process with the aim of increased metal recovery. The model is parameterized based on laboratory flotation tests of ore samples from the Assarel mine together with mineralogical studies by X-ray diffraction (XRD) and Mineral Liberation Analysis (MLA). A combination of several techniques allows reliable identification of mineralogical composition of the selected samples. The changes in the proportion between sulfide minerals in various products along the circuit have been also documented. Further, this information is used in the simulation model and in data reconciliation procedures for establishing mass balance. The simulation accuracy is studied by comparing the simulations with the plant survey based mass balance. Constructed simulation model can be used to run alternative process scenarios. As an example, the flotation circuit performance with different reagent regimes is simulated based on data from batch flotation tests. Two reagents were considered for this purpose, dithiocarbamate-based one and xanthogen formate/mercaptan blend. It has been revealed that these reagents do not have the same influence on the selective flotation. The one improves flotation of gold and overall recovery but without notable selective action. In contrast, the other showed better selectivity towards copper, rejecting more gangue and lowering gold recovery. The model is also applicable for process optimization studies with different feed compositions, flowrates and circuit configurations. INTRODUCTION In the pursuit for elevated technological indicators, finding an optimal set of process parameters fully utilizing the potential of the equipment is a key factor to success. Over the past decades, there has been a substantial development in flotation circuit optimization through performance benchmarking using metallurgical modelling and steady-state computer simulation. Practical simulation engineering tools are based on experimental data obtained from laboratory tests and from plant surveys and operation data. With the help of flotation models, it is possible to study grade-recovery response with different feed compositions and throughputs, and with various cell-operating parameters, as well as to evaluate and design different flowsheet configurations. Outotec’s HSC Chemistry® software, which incorporates simulation and mass balancing modules alongside with several other tools, can assist with this optimization (Mattsson et al., 2015)."

Jan 1, 2018

By D. I. Verrelli

Within the flotation community a belief has developed that some particle shapes are more ?floatable? than others. This is usually attributed to an influence of particle shape or roughness on the induction period required to achieve attachment between the particles and the air bubbles in the pulp. Up to now, such measurements have not been able to readily isolate the effect on individual flotation subprocesses. In contrast, our experimental apparatus, the CSIRO Milli-Timer, enables us to directly observe the process of particle?bubble interaction and attachment by means of a high-speed video recording, thus providing a direct measure of the induction period for attachment. To assess the influence of particle shape on induction time we used two varieties of methylated borosilicate glass particles ? spheres and angular ?frit? ? in a range of tightly-sized fractions. In doing this, we take care to account for the influence of other factors that could affect the induction time, such as the polar angle of sliding commencement, and approach velocity. These parameters are recorded as variables for each interaction, and corrected for using multiple nonlinear regression. Our results illustrate the importance of particle shape on induction period, with angular particles exhibiting induction periods that were an order of magnitude lower than those of spheres. Furthermore, the induction period was seen to decrease with increasing particle velocity, or kinetic energy on approach, but increased as the trajectory approached the limit of just grazing the bubble. Particle shape in mineral processing is a consequence chiefly of the mineral type and the type of grinding employed. The results presented herein indicate that attention should be paid to the shape of particles obtained from the grinding operation, besides particle size. Keywords: attachment, bubbles, flotation, induction period, particles, shape effects, surface roughness

Sep 1, 2012

By S. N. Shahcheraghi

Grinding is one of the most important and expensive steps in mineral processing allocating about 70% of the total energy in the plants. Nowadays, for optimizing the energy consumption in these equipments, the rock behavior and its size distribution during the crushing have been normally predicted using selection and breakage functions to be able to optimally model and design grinding circuits. For this purpose, the case of Miduk copper mine in Kerman province, Iran was studied. The samples were taken from primary ball mills feed and were subject to screen analysis to achieve uniform sizes. Then, selection and breakage functions were determined at the different grinding times in laboratorial ball mill. Finally, ore size distribution in different grinding times was estimated using MATLAB software

Sep 1, 2012

By Javier Baladron, Mijail Villar, Brandt Henriksson

"In this presentation an overview will be given of what has been observed by the authors in the copper concentration industry, with a large diversity of tailing thickeners operating under different conditions, although many of them are located in the same neighborhood. A closer look will be taken at the reported performance from different sites and from different thickener designs, either conventional or high rate, including those that were retrofitted, regardless of the thickener brand. An analysis is also made of the generic correlation of the size of the thickener and the performance in terms of solids loading (or unit area) and % solids. The paper envisions a technology development route, makes a brief analysis of the economic impact of the suggested route and points out the need for development in technologies around tailings thickeners, such as automation, yield stress measurement, slurry pumping and construction methods."

Jan 1, 2014

By Zhou Junwu, Han Long, Song Zhenguo, Sun Chuanyao

The deposit genesis, the ore property, and the mineral characteristics, which has a close relationship with the beneficiablity, could be regarded as the “Genetic Properties”, actually are the determining factors for beneficiation process development. However, in conventional concentrator’s process development and engineering, there have been lack of systematic research and test on those genetic properties, also lack of well-established collecting, statistics and analysis system for those huge amount of data such as the historical mineral processing technique research, process mineralogy study, practical operating and engineering data. Obviously it is far less than enough for profound integration combining modern IT together with traditional mineral processing technology, as a result there are a number of disadvantages in mineral processing R&D and engineering, such as long term, high cost, low efficiency as well as repetitive testwork not making full advantage of previous experiences. Aiming to make utmost of those Genetic Properties and overcome above disadvantages in mineral processing R&D and engineering, the concept of “Genetic Mineral Processing Engineering (GMPE)” is put forwarded, and the strategical study has been conducted on this regard, with the main focus on following aspects: a) Testing and extraction of the “Genetic Properties”; b) Establishment of data base and data warehouse of GMPE; c) Intelligent decision making system for beneficiation process; d) Verification testwork; e) Virtual concentrator. The technical route proposed is to firstly conduct research and test on those Genetic Properties mentioned above, based on that the specific data base will be set up and applied for intelligent process recommendation and simulation with a few verification testwork conducted in the meantime, finally achieve a fast, high efficiency and precise determination of technology and process for ore beneficiation. The systematic study on the three-in-one GMPE would make an innovative breakthrough in conventional mineral process testwork research and engineering methodology, and provide technical support for the concentrator’s design and upgrading.

Jan 1, 2018