Search Documents

By Yang Zhao, Tao Xiu-xiang, Chen Song-jiang

"China is rich in low-rank coals that account for 45.68% of existing coal reserves in China. The clean and efficient utilization of low rank coals is of great significance for ensuring the effective energy supply and promoting economic development and environmental protection. In order to solve the difficult problem in flotation of low rank coal, it has become the focus of research in the related field that oily bubbles instead of air bubbles are taken as a carrier in flotation to improve the attachment efficiency and recovery of low rank coal. In this paper, low rank coal slime collected from Shendong mining area was used as the experimental material, and it focused on the characteristics of oily-bubble flotation process of low rank coal. Additionally, difference in conventional flotation and oily-bubble flotation was discussed. The induction time between air bubbles, oily-bubbles and fine low rank coal particles was measured. The results indicated that the induction time between oily-bubbles and coal particles was obviously lower than that of air bubbles. By comparing the foam height of air and oily bubbles, it was found that the amount of oily bubbles is less than air bubbles, causing relative low flotation rate of oily-bubble flotation at initial stage. Besides, the maximum foam height and half-life of air bubbles and oily-bubbles were measured respectively. The results showed that the stability of oily-bubbles was higher than that of air bubbles, which is benefit for the enrichment of concentrates. The clean coal water recovery of oily-bubble flotation is lower than that of air bubble flotation, which indicated oily-bubble flotation is lower in water entrainment. INTRODUCTION China is the largest energy consumer in the world, accounting for 23% of global energy consumption in 2016 and 27% of global energy consumption growth. Whereas coal is taken as the major primary energy source and its share of China’s primary energy consumption is 62% in 2016, in which the low rank coals, such as lignite, long-flame coal, weakly caking coal, and non-caking coal, accounted for about 50% of total coal production capacity (China’s energy market in 2016, BP). Moreover, the exploitation and utilization of low rank coals and other coals that are difficult to float have been an important strategy for China’s sustainable development of the coal industry (Liu et al., 2014). However, the combustion of low-quality coals leads to a serious environmental pollution. In addition, the deterioration in geological conditions of coal resources, and the increasing improvement in the mechanization for mining significantly caused the increased amount of fine coal."

Jan 1, 2018

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012

By M. Maldonado

A flotation bank is a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three reported strategies: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data are analyzed with respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.

Sep 1, 2012

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By C. Tokoro

Co-precipitation of dilute toxic anions with ferrihydrite is an important removal mechanism in wastewater treatment system. Although, numerous qualitative studies have been published on removal characteristic from wastewater of dilute anions by co-precipitation treatment, detail mechanism or quantitative characteristic is not well understood. This paper discussed the co-precipitation mechanism of As(V) and Cr(VI) with ferrihydrite by comparative experiments between co-precipitation and simple adsorption. In this study, co-precipitation experiments and simple adsorption ones were distinguished closely. In the former, precipitation of hydroxides and adsorption of anions develop simultaneously, but in the latter, anions adsorb onto prepared hydroxides. Although high affinity anions for hydroxides (e.g. As(V) for ferrihydrite) showed quantitative difference of removal ratio between co-precipitation experiments and simple adsorption ones, low affinity anions (e.g. Cr(VI) for ferrihydrite) showed quantitative agreement in spite of deferent forms of ferrihydrites between them, that is, amorphous ferrihydrite was formed in co-precipitation experiments, but goethite was formed in simple adsorption ones. In order to discuss the mechanism of co-precipitation phenomena, three experimental studies have been carried out: (i) adsorption isotherm measurement in the co-precipitation experiments of As(V) or Cr(VI) with ferrihydrite, (ii) zeta potential measurement of co-precipitated or simple ad-sorbed ferrihydrite with As(V) or Cr(VI), and (iii) XRD analysis of co-precipitated As(V) for ferrihydrite. All experimental results suggested the main mechanism in co-precipitation phenomena of As(V) was not only a surface complexation (simple adsorption) but also a surface precipitation.

Jan 1, 2014

By A. Otsuki

This paper describes the evaluation method of dispersion and coagulation of silica nano-particles by means of interactive force apparatus. The apparatus measures the size of fine particles in aqueous solution or organic solvent of high concentration and/or low optical transparency. Other conventional apparatus for size measurements (such as, apparatus utilizing dynamic light scattering) are difficult to measure the size of particles in such conditions accurately, due to multi-scattering of light in the sample solution or solvent. The apparatus measures the interactive force between two surfaces, i.e. the gold-coated glass hemisphere and the brass flat plate, (which is fixed at the bottom of the sample cell). The apparatus has three parts, i.e. main part (which consists of electric balance, hemisphere and flat plate), control part (i.e. personal computer, piezo-stage controller and voltage supplier), and detecting part (i.e. multi-meter and oscilloscope). During the measurement, electric field is applied between the hemisphere and flat plate, and thus dielectric particles are arranged toward the direction of electric field in the area between two plates. When the two plates are close to each other, two different forces (i.e. repulsive force and attractive force) will alternately act on particles due to the structure change of the particles. The repulsive force occurs when the structure of particles is stretched by compressive force; whereas the attractive force occurs when the aggregate structure is broken. The cycle of the repulsive and attractive forces is a primary size of particle or size of aggregate, which depends on the degree of agglomeration. The measured size of particles, which is varied depending on their degree of dispersion and coagulation, determined the characteristics of the silica particles. In this research work, the effect of size and concentration of particles in aqueous solution on the degree of dispersion and coagulation of the silica particles were investigated. Spherical silica particles were selected for this investigation due to their variety of size. This apparatus can be used to evaluate the degree of dispersion and coagulation of other nano-particles in various solvents in many process industries.

Jan 1, 2014

By V. Panayotov

Flotation practice usually uses the Sheridan-Grizvold selection method, where zinc minerals are activated by addition of copper sulphate and depressed by addition of sodium cyanide, ferrous sulphate, zinc sulphate or various mixtures of these reagents. The method is suitable for the flotation of sulphide ores, which, do not bear precious metals, such as silver and gold. When classical technology with cyanide is applied to depress zinc minerals, the precious metals, which are contained mainly into lead minerals, are dissolved into the solution, which represents a technological loss. In order to avoid this process, we have made use from the knowledge on the semiconducting properties of lead and zinc sulphide minerals. We have changed the surface charge of minerals by means of an electrochemical impact realized by direct current application and specially designed set of insoluble or semi-soluble electrodes. Thus, flotation separation of lead and zinc sulphide minerals was achieved, at increased recovery of lead, zinc and silver. The technology proposed was implemented in a Bulgarian flotation factory; it worked over 5 years providing significant, positive economic, technological and environmental impact. Silver recovery was increased by 0.8-1.0 %, and lead and zinc recovery was increased by 0.8-1.0 %. The technology is easily controllable and adaptable to raw materials and parameters of the technological process. It can be paid back for 6-8 months after the implementation. Keywords: lead-zinc flotation separation, electrochemical impact

Sep 1, 2012

By K. A. Natarajan

"Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.In this paper, the role of acidophilic chemolithotrophs such as Thiobacillus thiooxidans and neutrophilic heterotrophs such as Bacillus polymyxa in the beneficiation of sulfide and oxide minerals is illustrated. Mechanisms of bacterial attachment on various sulfide and oxide minerals are outlined with respect to the influence of bacterial interaction in bringing about mineral surface hydrophobicity or hydrophilicity. The role of bacterial cells as well as metabolic products such as bioproteins and exopolysaccharides in significantly altering the surface chemistry of sulfide minerals such as sphalerite and galena and oxides such as hematite, alumina, silica and calcite is discussed with probable mechanisms. Possibilities of generating mineralspecific bioreagents are outlined with respect to bacterial adaptation to mineral substrates."

Jan 1, 2003

By V. M. Bystritsky, M. G. Sapozhnikov, G. M. Nikitin, A. B. Sadovsky, Yu. N. Rogov

"At present kimberlite ore is processed in crushers or grinding rolls with subsequent grinding in wet mills down to a size of 0.2 mm. The basic disadvantage of the standard diamond processing technology is that crushing kimberlite ore can damage the most valuable large diamonds of few carats. Tagged neutron method offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The results of the tests of the neutron separator prototype carried out at the Lomonosov processing factory of PJSC Severalmaz are discussed. The possibility to detect the diamond in the rock whose size is 10 times larger than the size of the diamond is demonstrated.INTRODUCTION At present standard diamond processing technology implies disintegration of kimberlite ore in crushers or grinding rolls down to a size of 0.2 mm. It inevitably leads to high probability that large and most valuable diamonds could be damaged. The fraction of diamonds which lost integrity in the process of ore enrichment could be as large as 35-65% [1]. Tagged neutron method (TNM) [2] offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The main idea of the TNM is irradiation of an object by fast 14.1 MeV neutrons from binary nuclear reaction d + 3H ?4He + n (1) and detecting (tagging) the 4He (a-particle) that accompanies neutron. That gives possibility to determine direction of the neutron momentum. Those tagged neutrons irradiate kimberlite ore under investigation and produce gamma rays via inelastic scattering reactions with nuclei"

Jan 1, 2018

By Tuan V. Nguyen, Kosta Simic, Louis Mittoni, Murray Rudman, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D .Improving Thickener Technology. project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By Leon Lorenzen, Trevor J. Britz, Pierre J. Van Zyl, Ellis R. Els

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003

By Özcan Y. Gülsoy

Coal beneficiation with optical sorting has not yet been studied in detail. Optical separation of coal from gangue particles as a dry method can be used as an alternative to the other enrichment methods. Developments in optical and pneumatic technology put the optical sorting one step forward by means of applicability of the mechanical sorting to the mineral industry. Because of the inefficient separation performance, dry separation of coal is very limited in industrial applications. Therefore, optical sorting depending on color differences between two minerals can be introduced to coal beneficiation systems. In this study, coal samples obtained from Konya-Ilgin region (Central Anatolia-Turkey) were separated by optical sorter and the results were evaluated. The conventional floatability tests for Ilgin coal are conducted by collecting most of the feed material at 1.3-1.4 g/cm3 density range. Separation of Ilgin coals with heavy medium methods will not be possible because of poor density difference between coal and its impurities. There are important color differences among the floated particles at 1.3-1.4 g/cm3 density range. Therefore, Ilgin coal is subjected to optical sorting in a pilot scale optical sorter. Different size fractions were fed to the optical sorter and then rejected and accepted particles by equipment were analyzed. Ash content of the accepted particles was reduced to 25-35 % and ash in tail increases up to 55-60 % after sorting. Although most of the material floated at low densities, optical sorter separated the feed into two different quality products. This study has the potential to clarify applicability of optical sorting even to non-floatable coals and to provide an important contribution to both industrial applications and literature.

Sep 1, 2012

By C. R. Mambote

Vanadium is an important metal that is used mainly in ferrous and non-ferrous alloys due to the high tensile strength, hardness, fatigue resistance and corrosion resistance. Vanadium consumption in the steel industry represents about 85% of the vanadium-bearing products produced worldwide. The primary sources of the metal are patronite, roscoelite, and mottramite. Vanadium has also been produced as a by-product of the uranium production program which uses carnotite ores as a source of uranium. Vanadiferous magnetite iron ores are used for producing vanadium as well. In addition, it is known that vanadium can be recovered from the ashes of crude oil and petroleum coke. The process for treating boiler residues, fly ash and petroleum coke is similar to the process used to treat spent catalysts and ores. However, some of these materials may contain high carbon that must be removed at specific stage of the operation. Several processes are available for obtaining vanadium from fly ash, such as roasting vanadium bearing materials in the presence of sodium salt. The salt roasted calcine is subsequently leached with an alkaline or acidic solution. To obtain a cal-cine from which the vanadium can subsequently be recovered, the carbon in the source materials has to be eliminated prior to the roasting process. Other processes use the conventional hydrometallurgical route, in which fly ash is leached with sulphuric acid to obtain an impure vanadium pentoxide. The impure vanadium pentoxide is then treated with a sodium carbonate solution under atmospheric conditions to subsequently precipitate vanadium as ammonium metavanadate. Actually, the salt roasting process is the only process used commercially. In the present study, the progress in the technology of vanadium extraction from secondary materials is reviewed. The perspectives and the challenges for new process development are discussed.

Jan 1, 2014

By W. G. Wu

More and more researches and applications of organic chelating agents as depressors or activators are carried out in the course of research and application of modern flotation. The paper puts forward the necessary condition of organic chelating agents as depressors or activators by analyzing the chelating chemical performance of organic chelating agents with metal ions and the stability of chelates formed by them; at the same time, puts forward four sufficient conditions of organic chelating agents as depressors or activators according to different hydrophilic capability of the chelates and different performance of depression and activation of organic chelating agents for minerals. Namely, the ?1+1/4? necessary and sufficient conditions of organic chelating agents as depressors or activators are put forward.

Jan 1, 2014

By Kari Niiranen, Andreas Fredriksson

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. Geometallurgy, which combines geological and metallurgical information is not a new way of thinking at LKAB, but rather a revised and updated version of an old working process. A project called "Silica in the Mine" which started in 2007, was an important reason to set a new focus at the geometallurgy. The target of the project was to develop a simplified method in laboratory scale to predict SiO2 grade in the magnetite concentrate in Kiruna and further predict the physical properties of the crude ore with respect to processing characteristics. The connection between mineralogy and products properties have started to be even more vital and necessary to examine due to the future exploiting new iron ore deposits. Geometallurgy at LKAB can be described as a mental and strategic framework where the Research and Development department (R&D), and others within the organization of LKAB, aims towards the connection of the minerals-production-products. It could in its basics be called "research & development", but it must be clarified that changes have been made, mainly due to the development on the instrumental analysis side. LKAB’s idea is to work quite broad, with internal educations, an active working process in ongoing projects, together with external parties (such as universities), with several PhD-projects and an upgrading on the instrumental side at the LKAB Research & Development department. This paper is a summary about the concept Geometallurgy at LKAB and some of the actions within its framework.

Jan 1, 2014

By John C. Gathje, Rick Moritz, Wilhelm de Beer

"Froth flotation has a long history of success for the recovery and concentration of a wide variety of minerals of commercial interest. Both the art and science of flotation have progressed greatly, and as our knowledge has increased so has our ability to improve mineral separations and recoveries.One area of interest in recent years has been the flotation of refractory gold ores to recover the gold-bearing sulfides. In many instances, the use of conventional air flotation to concentrate these values has achieved only limited success. However, as a result of intensive research, Newmont Mining has expanded the boundaries of flotation, and it can now be used to successfully treat many gold-bearing sulfide ores as well as platinum and palladium ores. This has been achieved through the use of the N2TEC technology, which utilizes nitrogen as an inert gas in the flotation process.Laboratory and pilot plant investigations and a commercial plant have proven its worth. Compared to air, the patented N2TEC process has increased the gold recoveries of many ores by 5 to 15 percentage points, and improvements of an even greater magnitude have been observed. This paper describes the process development for the flotation plant now being operated at Newmont’s Lone Tree Mine located in Nevada, as well as development work that was done on ores from their Twin Creeks Mine also located in Nevada."

Jan 1, 2003

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By Francisco Vicuña, Miguel Becerra, Gonzalo Montes-Atenas

"The optimization of the copper recovery from smelting slag by a process of comminution / flotation has been a widely discussed topic during the last few decades. Several studies covering the characterization of different types of slag, the impact of the slag cooling rate and of different flotation operating conditions on the flotation performance have been widely published. Currently, at El Soldado mine site (Angloamerican), there are large copper bearing slag deposits that can be a profitable alternative for the concentrator with capacity to treat this material. Under this process schema, the optimization of the flotation process to obtain better copper recoveries is a relevant topic of study. The aim of this study is to assess the efficiency of a sulfidation stage of a slag and to correlate that process with copper recoveries results in a flotation circuit. This article presents a detailed examination at both laboratory and plant scales of the slag sulfidation on the recovery of copper in the flotation process. The experimental methodology involves studying the effect of the sulfidation agent dosage, the pH, the particle size distribution of the flotation feed and the conditioning time. Furthermore, the performance of the sulfidation stage was analysed through the XPS analytical technique. It was observed that the sulfidation of particles in floatable size fractions correlated well with the increase in copper recovery. The results indicated that it is possible to increase between 2 to 4 points the total copper recovery with a sulfidation process implemented appropriately."

Jan 1, 2014

By Wenqing Qin, Yunfan Wang, Ximei Luo, Fen Jiao

In order to investigate the effect of nanobubbles on adsorption of surfactant on mineral surface, the nanobubbles on the surface of calcite with -37µm fraction in the sodium oleate system were controlled by pressurization and decompression to mixing vessel. Subsequently, the adsorption amount of sodium oleate on the surface of calcite were detected by ultraviolet spectrum at different stirring times and different pressures. At the same time, the nanobubbles on the calcite surface were imaged with atomic force microscopy (AFM). In addition, a homemade vacuum Hallimond tube device was used for the flotation of single mineral, and the grade and recovery of minerals in concentrate was used to determine the influence of the nanobubbles on flotation. The experimental results showed that a large number of nanobubbles were found on the calcite surface by AFM under the dissolved oxygen difference (DOD) condition of -4 mg/L. And a large difference in adsorption capacity of sodium oleate on the surface of calcite was observed under different air pressure conditions. It indicated that the ambient pressure had a certain effect on the adsorption of sodium oleate on the calcite surface, and this effect did not depend on the constant low pressure or constant normal pressure, but depended on the changing process of pressure. The single mineral flotation experiment results indicated the recovery of calcite under decompression condition (formation condition of nanobubbles) was 1.5-2 times that under constant normal pressure, and the flotation time is much shorter. Moreover, the recovery under constant normal pressure was greatly influenced by flotation time. In this paper, only one aspect of the effect of nanobubbles on mineral flotation was preliminarily explored. It was confirmed that after vacuum-pumping, the adsorption of sodium oleate on calcite surface could be increased, the flotation time also was greatly reduced and the recovery of calcite was increased.

Jan 1, 2018

By Q. Huo

The alumina production might not continue when the sulfur content of bauxite was too high. In order to bring down the sulfur content in bauxite, we studied on the bauxite desulfurization by bacteria screened from the acid mine drainage at mines of high sulfur content. The screened bacteria were domesticated by the high sulfur content bauxite. The experiments of bauxite desulfurization were carried out under the conditions of 5% pulp density, temperature of 30?, rotate speed of 120rpm. Bacterial desulfurization for 30 days, the sulfur content of the bauxite was reduced from 5.73% to 1.55% and the desulfurization percent was 72.9%. The recovery percent of alumina was 94.3%. The study showed that it was feasible to bring down the sulfur content of bauxite by bioleaching and this technique might make full use of the low grade bauxite.

Jan 1, 2014