Search Documents

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By Negin Khalili-Motlagh-Kasmaei, Paul O'Leary, Christopher J. Rothsiedl, Dimitar Ninesvski, Alexander Zöhrer, Vincent Winter

This paper presents the implementation of a digital twin for the vibro-replacement ground improvement process, as part of a digital construction site. The goal is to implement an evidence-based quality assurance for each produced element (column or point). The system uses a combination of planning data and real-time machine data collected automatically from construction equipment. In addition to the quality assurance, feedback is provided in a number of areas, e.g., condition monitoring of the equipment. The digital twin builds upon the real-time sensor and machine data, fused with metadata, to implement a digital model for the process. A hierarchical data evaluation, using rule-based Key Performance Indicators (KPIs), permits viewing of the spatial variation of data over the construction site. This permits the modelling of systematic variations in subsurface properties across the site, enabling the detection of anomalous individual elements, the diagnosis of their cause and the prediction of properties as construction proceeds over the site. All time-series data and KPIs are represented by standard classes of objects, leading to a generic coding of the data analysis; this minimizes the effort required to add additional sites and/or new KPIs. Examples are presented for a number of sites, where the system was used to identify anomalous columns.

May 1, 2022

By J. J. Beresford

The primary function of a support slurry is to provide stability during excavation. Today foundation structures can be designed around the additional friction afforded by the absence of the filter cake attributable to the use of polymeric fluids as support slurries. These fluids use pseudoplastic fluid viscosity to advantage over the fragile thixotropic gel structures of bentonite. Many of today&apos;s polymeric fluids are environmentally acceptable for disposal directly to municipal sewers.

Jan 1, 1989

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By Barritt Lovelace

Collins Engineers has been researching and implementing the use of drones on Civil Engineering Projects since 2015. Applications include bridge inspection, asset management, mapping, construction site management and emergency response. Recently this technology was used to map and model construction sites with deep foundations to verify and quantify designs. The ability to collect and use large amounts of data is transforming our world. Drone hardware and software is being used to capture and digitally replicate assets, giving owners unprecedented ability to visualize and manage their projects. Our teams help owners collect and process drone data into deliverables to be analyzed, annotated, stored, and shared. The use of drones can transform the way projects are managed and can improve project workflows. Data collected with drones can be processed into a digital twin of any project site or asset. This digital twin provides owners with a three-dimensional geometrically and geospatially accurate model. These models can be annotated and tagged with information that can be stored and shared locally or on cloud-based platforms. The data can be exported and used in a wide variety of CAD and GIS platforms. Goals When considering the use of UAS for several items need to be considered when establishing project goals. Safety Drones can be used to reduce job site safety risks in two ways. The first is that use of the drone can remove personnel from harm’s way. Surveyors and other project staff will traditionally walk the site to collect survey and other site information. These efforts can be replaced with the use of a drone eliminating much of the need for personnel to be on the job site itself which improves safety. The other way safety can be improved is that a digital model of a job site can be created on a daily or weekly basis that can be quickly analyzed for safety hazards. This analysis could be done remotely by safety officers to identify job site hazards which can then be corrected before injuries happen. Improved Deliverables Perhaps the most important reason to incorporate drones into project workflows it the ability to improve the project deliverables. Drones have the ability to quickly collect large amounts of high quality data which can be processed into orthomosaics, point clouds and 3D models that give engineers and project managers the information they need to make better decisions on design or project management.

Jan 1, 2019

By Shreya Vivek Hokam, Dr. A. I. Dhatrak, S. W. Thakare, Dr. Vivek S. Hokam

Construction in congested urban areas has necessitated tall and massive structures. In urban areas, it is common to construct underground structure nearby existing buildings. Selection of an appropriate support structure system to be implemented in the excavation in an urban area is heavily dependent upon the geotechnical conditions and safety of the surroundings and neighbouring structures. Urban Rail, popularly referred to as Metro Rail, has seen substantial growth in India in the recent years. More cities are experiencing the need for metro rail to meet their day-today mobility requirements. The metro structures involved deep excavation for foundations which induces the stresses and thereby alters the existing equilibrium and thus may affect stability of neighbouring structures considering safety point of view. Hence, design and execution of deep excavations become one of the important challenging tasks of any geotechnical engineer in the modern era. Further, it is important to control the ground movement in order to prevent the failure of excavations. This involves specialized foundation technologies, usage of sophisticated equipment and new methods in underground construction, safety and monitoring systems. In this paper the methodology used for protecting adjoining structures due to deep excavation for Nagpur Metro station is studied.

Sep 1, 2022

By D. G. Bishop

This paper is intended as a review and update of the use of Pressure Injected Footings as deep foundation units in North America. We will discuss various aspects of this pile and then discuss a particular project - the Mobile Alabama Convention Centre which is currently under construction. Pressure Injected Footing is a generic name used to describe a foundation unit that has been in use around the world for some 80 years. It has been used on all types of structures. It is an excellent pile in both compression and tension. It is particularly economic where a layer of granular soils can be found at relatively shallow depths. Other types of piles would penetrate these layers. Caissons are often difficult to construct in these soils because of their lack of cohesion and the often present water table. PIFs can density these shallow layers and carry relatively heavy building loads on them.

Jan 1, 1992

By Harry Schnabel, Mitchell L. Fong, Douglas R. Jenevein, Thomas S. Lee

"The Warm Springs Extension (WSX) is one of a series of projects that will eventually extend the Bay Area Rapid Transit System (BART) from Fremont to San Jose, California. A cut and cover tunnel was used for a portion of the extension that runs through Fremont Central Park to minimize the impacts that an at-grade railway would have on the Park. A cement deep soil mix (CDSM) wall was selected by the engineer as the preferred method of providing structural support and groundwater cut-off for a portion of the tunnel where it passes through an important aquifer and near Lake Elizabeth. In addition to the CDSM wall, a jet grout plug was constructed at the base of the tunnel to provide a complete groundwater cut-off.This paper will discuss the unique quality assurance and quality control measures taken for the soil mix wall and jet grout plug as well as the methods used to repair leaks and mitigate water seepage through the exposed wall and grout plug.PROJECT DESCRIPTIONThe Bay Area Rapid Transit (BART) Warm Springs Extension (WSX) project is located south of the existing Fremont BART station extending 8.9-km (5.4 miles) to Warm Springs District in Fremont, California. The WSX project has been divided into two contracts with different delivery methods. In order to minimize impacts to Fremont Central Park, a subway was selected at this portion of the alignment under a conventional design/bid/build contract.The Fremont Central Park Subway (FCPS) which begins on the south side of Walnut Ave and ends just north of Paseo Padre Parkway and is about 2.3-km (1.4 miles) long. Fig. 1 shows the entire WSX and the FCPS project. The FCPS contract consists of a cut-and-cover subway box, subway transition structures, ventilation structures and a section of which transverses Lake Elizabeth (a man-made lake). The geologic conditions consist of fill (sand, silt, clay and construction debris), Young Alluvium (clay and silt), Basin Deposits (clay, silt, and sand), and Older Alluvium (sand and gravel) as shown in Fig. 2.HYDROGEOLOGY OF THE PROJECT SITEThe FCPS is dominated by two geologic features - the Hayward Fault and the Above Hayward Fault (AHF) aquifer. The AHF aquifer provides a significant source and storage of water for the local water district. The underground subway will penetrate this aquifer and is up to 11m (36 ft) below the groundwater table. No groundwater was allowed to be pumped during construction of the subway box by Alameda County Water District (ACWD). To facilitate excavation for the subway box, temporary cut-off walls and a grout plug were designed to retain and resist high differential hydraulic pressure. The following section describes the selection of a deep soil mixing method for water cutoff. Design of the grout plug has been described in Lee, et al., 2011 and Fong and Lee, 2009, and is not the focus of this paper."

Jan 1, 2015

By Lawrence F. Johnsen, Felix Ferrer, Dino Tomasetti, Cassandra A. Wetzel

"A 17 story building was constructed at the Brooklyn Navy Yard on a site with a long history of development. Most recently the site supported a dewatering well and craneway to service two adjacent drydocks. The subsurface conditions generally consist of the following strata and approximate depths: miscellaneous fill and debris to 20 ft., organic soils to 35 ft., liquefiable sand to 45 ft., varved clay to 65 ft., glacial till to 95 ft. and gneiss bedrock.Hollow core bar piles replaced 18 in. diameter caissons on a 1.67:1 basis. The resulting service loads on the hollow bar piles were 600 kips compression, 21 kips lateral, 180 kips tension and 450 inch-kips moment. The top 30 feet of the hollow bar was cased with a 16 in. x 0.375 in. Grade 50 steel pipe. The piles were socketed 6 feet into bedrock. An extensive load testing program confirmed the axial and lateral load capacities. The paper will also discuss some adjustments to the installation procedure based on the load test program.PROJECTThe hollow bar piles were installed to support a 95,000 sf footprint, 17-story office building at the Brooklyn Navy Yard. The Brooklyn Navy Yard was first developed in the late 1700’s to build merchant vessels. The federal government purchased the old docks and adjoining 40 acres in 1801. The site was an active U. S. Naval Shipyard from 1806 to its decommissioning in 1966. At its peak in World War II it employed 70,000 people, 24 hours a day. Since 1966 the property has been converted to private manufacturing and commercial activity.The site is located between Dry Docks 2 and 3. The adjacent drydocks extend 40 to 43 feet below grade. The drydock walls are restrained by tierods extending back to deadman anchors. The site is also underlain by piles that were installed to support rail lines and a craneway. The building footprint also covered an 85 ft. wide, 70 ft. deep dewatering well which had a thick slab. The structural engineer for the project, ARUP, designed the building to span over the dewatering well.SUBSURFACE CONDITIONSIn September 2014, Langan Engineering conducted a geotechnical engineering study for the project. Figure 1 provides a subsurface profile through the long axis of the site. The general soil profile was very erratic but generally consisted of miscellaneous fill and debris to 20 ft., organic soils to 35 ft., liquefiable sand to 45 ft., varved clay to 65 ft., glacial till to 95 ft. and gneiss bedrock. The fill contained numerous obstructions from the over 200 years of site development. The organic soils were mostly very weak and compressible organic silt. The depths and thicknesses of the varved clay, and sand varied"

Jan 1, 2017

By Richard J. Finno

This paper presents an overview of methods that can be used to predict damage to buildings as a result of excavation-induced ground movements and describes an adaptive management approach for predicting, monitoring, and controlling excavation-induced ground movements. Successful updating of performance predictions depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the optimization techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors and emphasizes their inter-dependence. Case studies are presented to illustrate the capabilities of this approach. Examples are given to show how optimized parameters based upon data obtained at early stages of excavation can be used to predict performance at latter stages, and how they can be applied to other excavations in similar geologic conditions.

Jan 1, 2010

By David A. Jack

The Mission Valley Viaduct is located in San Diego, California. This structure is the intersection of Interstate 8 and 805. The project consists of the main viaduct, 8 connecting ramps, and one highway overpass. This job was originally built back in the 70&apos;s. After the Loma Prieta Earthquake in 1989, Caltrans began an aggressive program to seismic retrofit all of its bridges throughout the state. Most retrofit designs required major upgrades to the existing footings. These footing upgrades consisted of either driven or drilled shaft piling. The existing footings of the Mission Valley interchange were supported on driven H pile. The soils throughout the site were dense sands and gravels, cobbles, occasional boulders with a dense sandstone bearing strata, which varied through out the site. It was this sandstone strata that the engineers designed their pile tips around. High ground water in sandy soils created a high probability of liquefaction in all of the upper stratas.

Jan 1, 1998

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

The city of Naruto in the southwestern part of Japan is situated at the mouth of the mighty Yoshino River. An approximately 1,000m-long levee/bulkhead along one of the river’s tributaries in the city was raised with prefabricated steel panel walls on a concrete base bulkhead. Some sections of the walls’ foundations were combi-walls made of sheet pile cut-off walls and interspaced pipe piles; both of which were installed with press-in piling because the new wall alignment was very close to existing homes and businesses. A Clamp Crane, which clamped onto already installed piles and moved forward and backward on them, was utilized for a segment where the access to its piling location was too tight for a conventional crane or a track-mounted pile driver to maneuver.

Sep 8, 2021

By Brandon T. Buschmeier, Sonia S. Swift, Michael P. Walker, Frederic Masse

"Ground improvement has undoubtedly become a cost-efficient and effective solution to support the development of poor soil sites. Ground improvement elements, such as Controlled Modulus Columns (CMCs), replace piles by improving the subsurface soils and reducing settlement. As ground improvement becomes more popular, the applications become more creative and ground improvement is being used to control settlements under large structures with tight settlement tolerances.In this paper, we will discuss the use of CMCs to support two (2) large industrial warehouses where soil conditions would normally lead to the use of deep foundations and a structural slab, grade beams, and hung utilities to prevent excess settlement. Each of the sites we will discuss had poor soil conditions in the form of very soft or compressible soil, heterogeneous fill of varying thickness, and environmental contamination. At each site, we developed a design that would allow for the use of Controlled Modulus Columns (CMCs) with a Load Transfer Platform (LTP) in place of the previously-proposed deep foundations. The use of the CMCs also allowed for the use of spread footings and slab on grade construction. The benefits of this value-engineering approach include economy in the foundation system, risk mitigation by not disturbing contaminated soils requiring expensive removal, and ease of access for future sub-slab upgrades with new tenants. Additionally, the use of recycled concrete aggregate as an LTP is more environmentally friendly than placing structural slabs with heavy steel reinforcement.Designing for the settlement of large warehouses is challenging because it requires changing how we typically perform our designs. For most structures, the slab loads are relatively light when compared to the footing loads, whereas for warehouses, the slab is heavily loaded compared to the relatively light footing loads. Thus, it becomes essential to perform three-dimensional analyses to confirm that the proposed CMC layout will provide uniform support of the slab and footing across a variety of loading scenarios (loaded bays vs unloaded or travel bays). The complexity of the designs for these warehouses generated interest in conducting large area load tests over a grid of multiple columns. The performance of the area load tests provided invaluable information on the effectiveness of the LTP and CMC spacing. In this paper, we present a general description of CMC ground improvement, the differences between ground improvement and traditional pile foundations, our typical design methodology for CMC design, and the modifications to that methodology for warehouses."

Jan 1, 2017

By Christopher M. Kenney

Augered-cast-in-place (ACIP) piles have been utilized on commercial projects throughout many parts of the country for years, but are only beginning to be scrutinized for use on major infrastructure projects and other critical structures in some regions. Numerous engineers are aware that ACIP piles are an economical foundation alternative, and many technical papers have been presented that provide reliable methods of estimating ACIP pile load capacity. However, designers may not yet appreciate that the load-settlement behavior of ACIP piles is very similar to that of drilled shafts. This paper analyzes ACIP pile case histories from throughout the country and demonstrates that ACIP pile settlement under applied load is consistent, predictable, and very similar to the documented behavior of drilled shafts. This paper also presents a simple but accurate method of estimating ACIP pile settlement at the design load, and illustrates the need to estimate the equivalent diameter of the as-built ACIP pile when estimating pile behavior. Finally, this paper presents back-calculated values of the drained elastic modulus from the ACIP pile case histories that may be useful to those using more sophisticated methods of estimating ACIP pile settlement.

Jan 1, 2001

By Ross T. McGillivray, David S. Graham, Dan A. Brown, Steven D. Dapp

"The Selmon Expressway includes an elevated structure extending across several miles of weathered karstic limestone geology, and represents a challenge for design because of the high variability of the material and the difficulty in characterizing the strength. The nature of the epikarst in this region of Tampa is such that variability can be extreme within distances of only a few feet. The weathered rock includes extremely soft soil infill within solution features on and within the formation. The limestone is so weathered that coring typically does not yield useful samples for strength testing, and in-situ Standard Penetration Testing (SPT) tests often encounter refusal blow counts. Thus the challenge for foundation design includes two components of reliability risks: the uncertainty associated with the ground conditions at a given foundation location plus the uncertainty associated with the foundation performance at a given location even when the stratigraphy is determined.This paper describes the design approach that has been implemented successfully for two projects at the Lee Roy Selmon Crosstown Expressway (LRS) in Tampa, Florida: the assessment and remediation of the reversible elevated lane (REL) foundations constructed in 2004, and the elevated expressways widening project constructed in 2012. Included in this design approach is a method developed for computing axial resistance in this local geology. Design for axial loading relies primarily on the development of side resistance, which was considered less subject to performance risks than base resistance. The calculation method incorporates a statistical analysis of SPT data, tempered by engineering judgment, to characterize stratigraphy at a given location into either soil, intermediate geomaterial (IGM) or rock.IntroductionThe subsurface stratigraphy of sites underlain by weathered limestone formations can be highly variable with respect to material layer thicknesses and strengths, even over short horizontal distances. This is the case for much of Florida, and particularly the Tampa area. These conditions present a challenging environment for the design of drilled foundations because of the need for a reliable determination of subsurface conditions at each foundation location, as they relate to the expected axial performance. Contributing factors include:"

Jan 1, 2015

By A. Bozorgzadeh, B. M. Jensen, B. N. Koelling, B. R. Murtaugh

"The Service Base mooring system originally consisted of two general types of structures, 19 timber piles cabled together and steel three-legged pipe piles. The St. Louis District fleet moored to the fleet barges which were tied off to shore-side concrete deadman and supported on the landward side by the timber and steel piles. The purpose of this project was to replace the existing floating wharf mooring system at the St. Louis Service Base. The Marine Design Center of the U.S. Corps of Engineers developed a three pile cluster system concept. The clusters consisted of one vertical pile and two batter piles. Piles in rock sockets were selected to resist the uplift loads due to high wind loads on the tall, spare lock gates stored at the floating wharf. This paper focuses on the design of the rock sockets for steel pipe piles with large uplift loads and the lessons learned during the design and construction of this system.INTRODUCTIONBackgroundThe U.S. Army Corps of Engineers’ St. Louis District is located at the critical transition point on the Mississippi River where it is a “locking river” north of St. Louis and an “open river” to the south. The St. Louis District is responsible for maintaining navigation channels on the Mississippi River, the Illinois River and the Kaskaskia River. It is also responsible for the operation and maintenance of five locks and dams within its geographic boundaries.The St. Louis District utilizes a fleet of vessels (dredges, crane barges, motor vessels, and barges) to support the navigation mission identified above. The St. Louis District Service Base, located in St. Louis, Missouri, serves as the base of operations for the district fleet. This riverfront facility originally consisted of a floating wharf, a railroad trestle, and a walkway down the river bank to the floating wharf. Historically, there have been two fleeting areas at the Service Base. The main fleeting area was approximately 965 feet long and consisted of six fleet barges (Figure 1). This area supported the Dredge Potter and its attendant fleet. The upper fleeting area was approximately 1,050 feet long and consisted of various stop log, crane and work barges, dredge pipe pontoons and work flats."

Jan 1, 2017

By James J. Anderson

In this talk I will report on an effort to reassess the risk of pile driving to juvenile salmonids migrating through Puget Sound. The study was motivated by the concern of the construction industry that provisions restricting pile driving during the spring migration is resulting in an unbalanced burden to the industry. In simple terms the industry wants to know if some construction can be conducted in the spring without harming the juvenile fish. Fisheries agencies have agreed to reconsider their regulations in the context of additional studies. So, in this talk I will present some thoughts on risk assessment in general and the results of our study to assess the impact of pile driving on Snohomish River juvenile pink and chum salmon that migrate through the Navy Homeport construction site at Everett. The research, which is being carried out by the Fisheries Research Institute at the University of Washington, was planned and is supported in a joint effort including: the Washington Department Fisheries, National Marine Fisheries Services, U.S. Fish and Wildlife Service; General, Manson, and Hurlen construction companies, the Department of Transportation and a number of Puget Sound ports authorities. I will first briefly discuss the early life history of the juvenile salmon the regulations are designed to protect Second, I will outline the legal criteria required for risk regulation and some specific thoughts on how a reassessment of pile driving risk might be approached. With this basis I will report on our research and how it can be applied to a new risk assessment.

Jan 1, 1990

By Ziyad Abunada, David O’Connor, Abir Al-Tabbaa

"Abstract Contaminated land remediation using soil mix technology (SMT) is a relatively recent development which has been shown to be a cost effective and versatile system with numerous environmental advantages over other remediation techniques. The added complexities and variability associated with contaminated sites has escalated the need for field trials, field monitoring and specific QC measures to be undertaken for this setting and was the rationale behind project SMiRT (Soil Mix Remediation Technology). The main aim of project SMiRT was field validation, testing and assessment to provide stakeholder confidence in SMT and increase its uptake for land remediation in the UK. The field trials involved the treatment of 800 m3 of soil, through applying six different remediation techniques with four different SMT systems and introducing over thirty binders and binder compositions with a range of installation methodologies. Various issues were faced during the installation process and which were addressed on site. This paper presents some aspects of early age field observations, field monitoring, in-situ testing, coring and laboratory testing of cored samples and highlights some lessons learnt, providing valuable information on the issues that need to be addressed for this application of SMT.IntroductionAlthough soil mix technology (SMT) was developed in the 1960s in Japan and Sweden for geotechnical applications, its potential in geo-environmental applications became evident more recently the 1980s in the US and in the 1990s in Europe, having since increased to provide a range of remediation systems (Al-Tabbaa and Evans, 2003; Al-Tabbaa et al., 2011). The most common applications to date have been (a) the construction of low permeability containment walls or cut-off walls to contain a contaminated site; (b) stabilisation/solidification (S/S) treatment, with cementitious binders, for physical and chemical encapsulation of contaminants in soils and (c) the installation of permeable reactive barriers (RPBs), which are permeable walls that intercept the groundwater flow and remove contaminants from it, by mixing special additives with the native soil. Contaminated land remediation using SMT is a cost effective and versatile approach with numerous technical and environmental advantages over other remediation techniques. These advantages include the use of simple and well established techniques and equipment, speedy implementation, applicability to sites of any size and to multiple contaminants, elimination of off-site disposal, low risk and low emissions. There is a lack of competing alternative technologies that offer the same level of versatility and economic, environmental and social benefits, under current environmental legislation constraints. In addition, most currently available contaminated land remediation techniques are only partially effective, and are relatively contaminant-specific. This makes SMT a promising and timely contender to lead the market place in offering a cost-effective, efficient and low risk solution to contaminated soil and groundwater remediation and has resulted in a range of recent innovations."

Jan 1, 2014