Search Documents

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

By Robert E. Schock, Eric J. Risberg

"Less than 20,000 years ago, the last of the glaciers retreated from the Chicago region. They left behind sheets of glacial clay till underlain by dense, over-consolidated till (“hardpan”) below which is the limestone bedrock, found about 100 ft (30.5 m) below street level. The most notable feature in this profile is the unusually soft clay till that has historically been called “Chicago Blue Clay.”But the founding fathers of Chicago really didn’t care about what was under the ground. They recognized the importance of the city’s location as a potential trade and transportation hub. With access to the East through the Great Lakes and access to the West through the Mississippi River system, the viability of the city was evident. Chicago’s population grew rapidly. The city continued to grow through the Civil War years, but was dealt a devastating blow in 1871 by the Great Chicago Fire, leaving the city in ruins. The Birth of the SkyscraperAfter the cleanup of the Great Fire came the first real building boom in Chicago’s history. During this era, buildings were generally founded on shallow footings bearing on sand or clay. Many multistory buildings were constructed between 1880 and 1890 on spread footings. The first tall buildings were constructed with load bearing masonry walls. These early tall buildings suffered significant settlement as the soft clay underwent consolidation.The Home Insurance Building, built in 1885, was 12-stories tall and is generally acknowledged to be the first “skyscraper” in the U.S. It was the first building constructed with an iron skeleton frame instead of load bearing masonry walls. Spread footings were used under the interior columns in an effort to better distribute the loads, but the building still experienced large settlements.Construction began for the Monadnock Building in 1891. The 17-story building was built using load bearing walls 7 ft (2.1 m) thick, supported on rail-grillage footing foundations. When completed in 1893, the Monadnock Building boasted the title “World’s Largest Office Building.” The total building settlement over the past 125 years has been measured at over 20 in (0.51 m). The engineering community in the late 19th century observed settlement, but did not yet understand the process of consolidation of the soft clay beneath the city. During this time, many of the new buildings required structural repairs during and after construction; the problem was especially acute in buildings where highrise towers joined lower podium structures."

Jan 1, 2016

By J. X. Wu

An investigation on the seismic damage to buildings with pile foundations in Tianjin region, was conducted after the earthquake which hit Tangshan in 1976. It showed that most pile-founded buildings have an excellent aseismic capacity. In this paper, several pile-founded projects suffering the seismic damage are introduced as examples, simplified calculations are made of the vertical bearing capacity of pile foundations and of the horizontal seismic force, and suggestions are presented in conection with the design of pile foundations in the liquified ground soil. The paper shows a frame structure which has a plie foundation with a box-shaped base. Analyses if its response to the earthquake has been carried out in accordance with the F.E.M. and results have been obtained.

Jan 1, 2010

By A. Fisher

The use of thermal integrity testing to verify the quality of deep foundations has increased significantly in the UK and other world markets over the last 5 years. The introduction of distributed fibre optic sensing to this field has broadened the range of applications in which it can be deployed and the types of foundations which can be tested. This paper presents how fibre optic sensing technology can be successfully deployed in the construction environment the range of foundation techniques to which it can be applied. Alongside developments in the practical aspects of thermal testing, progress has been made in establishing assessment criteria which can be used to evaluate the results. This paper presents recent examples of comparative studies on foundations which include both thermal integrity testing, cross hole sonic logging and intrusive coring. The use of distributed strain measurement during pile load testing presents an alternative means to verify the assessment criteria used for integrity testing. This new approach can achieve comparable results to foundation exhumation or intrusive investigation and at a fraction of the cost. This paper presents the findings of several such studies, highlighting the benefits and opportunities for future improvement of the method.

Oct 1, 2022

By Peter J. Nicholson

A new method of constructing retaining walls, in-situ, prior to excavation has been developed. This "Vertical Earth Reinforcement Technique" VERT, has been demonstrated at a full scale test wall at the National Geotechnical Experimentation Site at Texas A&M University. This 10 meter high wall, was constructed of elements of soil mixing in an array that forced composite behavior between the soil mixed elements and the in-situ soils. Inclinometers and extensometers were used to verify the performance of the wall. The construction and results of the testing are presented.

Jan 1, 1998

By Francisco A. Flores, José L. Aguirre, Héctor A. de la Fuente, Erika Bernal, Jorge Arroyo-Esquedla

This paper presents the analysis, design, and construction of soil improvement for storage tanks foundation support at a site in Tabasco, Mexico. A total of 980 Rammed Aggregate Piers of 12.5 m in length and 0.5 m in diameter were designed and constructed to support four storage tanks. The soil conditions at the site generally consist of loose to medium dense silty/clayey sand to about 8m depth, underlain by very loose to medium dense silty/clayey sand with seams of very soft clay. The use of Rammed Aggregate Piers induced densification of the soil to increase its stiffness and reduce the liquefaction potential to control both static and dynamic induced settlements. Standard Penetration Test (SPT) and Cone Penetration Test (CPTu) explorations were performed prior to and post soil improvement to compare the liquefaction potential and the Factors of Safety associated with the two conditions. Finally, the soil improvement installation rate is presented. Soil improvement using Rammed Aggregate Piers represented a suitable alternative to support storage tanks foundation in potentially liquefiable areas.

Oct 1, 2022

Jan 1, 2002

By Maurice Guillaud

The most striking innovations on diaphragm-wall construction plant are those associated with continuous real-time trajectory monitoring of the excavating tool (either a grab or a hydro-cutter). The recent equipments are fitted with clinometers and gyrometers to control deflection, rotation or deviation from the vertical, thus allowing to install diaphragm-walls with a verticality accuracy of less than 0.3%. One of the greatest advantages of extensive use of on-board IT systems on the Hydrocutters and hydraulic grab machines is that it aids quality control by automatically producing complete real-time reports of all excavating data (verticality, depth, type of ground, rate of progress, stoppages, etc.). These reports are available to the Engineer, providing the total transparency required for Works Supervision and the Quality Assurance Plan. They also provide the Contractor with input data for databases used for optimising efficiency and progress criteria on future jobs.

Jan 1, 2002

By Jeffrey A. Schaefer

The Olmsted Locks and Dam project is located on the Ohio River approximately 16.5 miles upstream of its confluence with the Mississippi River. It consists of twin 1200 ft. locks with floating and fixed approach walls, five 110 ft. wide tainter gate bays, a 1400 ft. wide navigable pass boat operated wicket gate section, and a 400-ft. section of fixed weir (Fig. 1). The project will have a total cost over 1.0 billion dollars, and as such is one of the largest civil works project underway in the Corps of Engineers.

Jan 1, 2001

By Stephen T. Young

The construction of Phase 2 of Hong Kong Station, its retail podium and International Finance Centre Two, the tallest building in Hong Kong, will be completed in the middle of 2003. This paper describes the design and construction of the slurry wall for the Station (both Phase 1 and Phase 2) and the two commercial buildings at the Station. The slurry wall is used as the permanent earth support wall for the station box and the excavation depth ranges from 70 feet to 120 feet. Top-down construction technique was adopted to support the excavation of the station, while circular cofferdams relying on hoop stiffness were constructed to support the basement excavation of the two towers. The designed behavior of the slurry wall is also compared to the as built behavior.

Jan 1, 2003

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994

By S. K. V. Avasarala

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading tests and installation of over 3,300 prestressed concrete piles for a building complex consisting of 12, 5- and 6-story over parking buildings. The project was recently completed in three-phases over a span of 4 years. The subsoil conditions were explored by performing 25, Standard Penetration Test (SPT) borings throughout the site. Various types of driven pile foundations were considered and following an evaluation of high structural loads and site-specific constraints such as variable depth of bearing layer of Florida limestone and quality of clay and limestone layers, a prestressed concrete pile support system was selected as the most economical and effective foundation approach. The building foundations were designed for a pile capacity of 353 kN (40 tons) in compression, 45 kN (5 tons) in lateral capacity for a deflection of 0.64 cm (0.25 in.), and 133 kN (15 tons) in uplift capacity. The axial and lateral allowable pile capacity and lengths were predicted using SPT91 and LPILE computer programs, which are generally used in Florida. The validation of these capacities was derived from 144 probe piles and performance of 12 pile loading tests on selected probe piles. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the loading tests on probe piles. This information was effectively utilized as part of the overall quality control program to install a total of 4,186 prestressed concrete piles (including 144 probe piles) in different building areas across the project site to depths ranging from 8 to 21 m (25 to 90 ft) below existing ground elevation as part of foundation support system. This engineered, monitored, and tested foundation solution provided an effective and satisfactory basis for completion and approval of the foundation work for this 12, 5- and 6-story over parking building complex. A recent reconnaissance has indicated that all the building foundations are performing satisfactorily.

Jan 1, 1995

By Theodore R. Maynard

The history of foundation engineering in Chicago is a tale of innovation, made necessary in order to keep pace with structural technology which allowed taller buildings with heavier bearing loads, to accommodate a non-conducive geologic setting. The geology as it relates to foundation construction and underground construction in general is briefly described. A chronology of important events from the birth of Chicago to the present is presented. The impact of various construction techniques which were either initiated or refined to allow the growth of Chicago are discussed. Introduction The growth of Chicago resulting in today's high-rise high-density population center can be looked upon as a history of modern underground construction. The two major reasons which explain this are 1) It grew up during a period of rapid development in the Industrial Revolution and 2) Its natural geological setting needed a great deal of innovation for continuing growth.

Jan 1, 1991

By Jewels Stover, Charles A. Luxford

Oklahoma City is undergoing a replacement program for an existing 66in (1.675m) water pipeline that conveys raw water from Atoka Reservoir to the City. This pipeline currently crosses the Canadian River on elevated piers and is subject to flood hazards. To replace the existing pipeline and mitigate flood damage concerns, two parallel microtunnels will be constructed below the river channel. Access is from construction shafts located near the midpoint of the tunnels; opposing drives are launched from each shaft. This geometry dictated shafts of significant depth – exceeding 120 ft. (37m). To accommodate the casing pipe segments and microtunneling machines, a minimum shaft diameter of approximately 34 ft. (10.4m) was required. Due to the difficult geologic setting, a reinforced secant pile compression ring is specified by contract in the top 70 ft. (21.3m) of these construction shafts to provide a very low permeability support system.

Sep 8, 2021

By Abhirami B., V. Balakumar

Piled raft foundation system is an intelligent geotechnical concept, developed towards reducing the settlement of the raft and the footings by providing pile elements below the raft or footings, as the case maybe. Although a large volume of works has been done on the behaviour of piled rafts by observational studies, the effect of construction methodologies such as deep excavations, the installation methodologies used for piling etc appear to have not been covered adequately. This paper discusses the effect of deep excavations, pile installation techniques and the effect of adding structural elements, based on the data available from published literatures. Based on this study, the performance of the piled raft monitored by the author has been revisited and the results of such a study are discussed.

Nov 1, 2022

By Philip J. Daynes

As part of the regeneration of the centre of Dublin, a multi-functional development is being constructed on the site of the historic Smithfield Fruit Market. The site is being developed in three phases, and includes one of the deepest basements (10m) constructed in Ireland to date. Until the recent improved economic climate, there has been little requirement for deep basements in Dublin, and this is the first to be constructed entirely within fluvio-glacial gravels and boulders. The difficult ground conditions led to the adoption of a diaphragm wall solution to ensure a watertight construction. Tie-back anchorages are utilised in the temporary case, and the wall is propped by floor slabs in the permanent case. Where required by high bedrock levels, the diaphragm wall is dowelled into limestone bedrock to ensure toe stability. The recorded lateral movement of the wall is significantly below that calculated by numerical analysis. Temporary bentonite cut-off walls were installed to divide the site into discrete sections. The basement was constructed as a tanked structure, and is subject to uplift water pressure. Passive tension minipiles provides an innovative alternative to the standard stressed anchorage solution. This paper describes:- design and construction aspects of the diaphragm wall, tie-back anchorages, and anti-flotation minipiles, together with recorded lateral wall movements,

Jan 1, 2003

By Amit Srivastava, Monica Malhotra

In a congested city or urban area, so called “lifeline of the city”, i.e. Gas, Electricity, telecommunication, as well as other utilities or facilities are supplied or transported underground through buried pipes or utility tunnel. Sometimes these buried pipes or utility tunnels are deep underground and interfere with the foundation of new structure. It is highly probable that a pile foundation is placed near an existing underground buried pipe or utilities tunnel and may influence its load bearing capacity. Hence, estimation of reduce load bearing capacity of the pile foundation placed near the existing buried conduit or utility tunnel is a complex soil-buried structure interaction problem. It is further complicated owing to uncertainty in estimation of geotechnical parameters of foundation soil due to measurement and testing errors, inherent soil variability and model transation. Under such circumstances, load bearing capacity is best assessed in probabilistic framework or through reliability analysis. The present study demonstrates how concept of response surface method (RSM) in conjunction with Numerical Analysis and First Order Second Moment (FOSM) methods can be combined to per the reliability analysis. The study answers the following question “reliability in reduction in the load bearing capacity of single pile placed near the existing underground pipe or utilities tunnel”. It is demonstrated that the approach provides first hand ination on the reduction in the load bearing capacity and then estimate the reliability of that estimation in terms of an index called Reliability Index (). Such preliminary investigation can be useful for advocating the detailed analysis as well as in the decision making for relocation of pile foundation.

Sep 1, 2022

By L. F. Miao

Studies were carried out to investigate the ultimate soil pressure acting on pile(s) undergoing lateral soil movement in soft clay. A special apparatus has been designed to apply a uniform rectangular profile of lateral soil movement on the rigid pile(s) with pinned head and tip conditions to obtain the ultimate soil pressure. The piles were 16 mm (5/8 in) in diameter. For the pile group tests, the behavior of different number of piles (2, 3, 4, 6 and 9), pile arrangements and center-to-center spacings (3 and 6 diameters) were investigated. In this paper, the group factors of 11 combinations of number of piles, pile arrangements and pile spacings are presented. The group factors are given for individual piles in a pile group as well as for the entire group. Generally, the group factors of individual piles in a group varied significantly according to pile spacing in both directions, and pile arrangement; the group factor of the whole group reduced with an increasing number of piles, and increased with increasing pile spacing. For a pile group with the same number of piles but different pile arrangement, no significant difference was found in the group factors for the entire group.

Jan 1, 2008

By Robert G. Lenz

Control of ground water for construction purposes is an everyday occurrence in the U.S. Thousands of pumps are in service at any given time. Most of these applications simply consist of pumping water out of an excavation, generally with the aid of sumps. Modern hydraulic and electric submersible pumps permit these procedures because of their ability to pump solids and take air without losing their prime. These procedures work fine up to a point and permit the contractor to control his ground water problems adequately and at minimal cost. When that point is exceeded, the ground water problems sometimes are compounded. Over-application of open pumping techniques can result in slope failures, cofferdam instability, bottom heaving, boils, loss of ground, damage to adjacent structures and utilities, and assorted other maladys which could and should be avoided. This paper will deal with the options involved in ground water control, a discussion of the unwanted side effects of dewatering, and examples of ground water control projects in various cities around the U.S.

Jan 1, 1988