Search Documents

By John C. Lyons

"The Wabana iron ore deposits occur as flat-dipping beds of oolitic hematite and chamosite, of Lower Ordovician age, which outcrop for 3 miles along the northwest coast of Bell Island, Conception Bay, Newfound-land, about 16 miles from St. John's.The deposits occur in three zones, Upper, Middle, and Lower beds, separated respectively by 30 feet and 215 feet of shale and sandstone. They are primary sediments laid down in a shallow tidal basin by the precipitating action of a marine environment on iron-rich fresh waters flowing into the basin.The ore-bearing zones, while of wide areal extent, are not uniform beds of hematite that can be mined wholesale. The action of waves and currents during sedimentation; the delta pattern, velocity, and transporting power of streams flowing into the basin; the contours and oscillations of the sea bottom on which the sediments were laid have all been fundamental in the emplacement of richer and thicker mineable sections, and of lean zones so intercalated with shale as to be unmineable.The preservation of the deposits is due to their location in the Conception Bay syncline and to a considerable upthrust of the country east of the bay in post-Ordovician time.The hematite deposits were first recognized as such in 1892, and soon after were acquired by the Nova Scotia Steel and Coal Co. They are now being mined by Dominion Wabana Iron Ore, Limfred, a wholly owned subsidiary of the Dominion Steel and Coal Corporation, Limited. Production started in 1895, and up to the end of 1955 totaled 58,588,516 long tons of hematite ore, having an average dry analysis of about 51 5 per cent iron, 11 8 per cent silica, 0·9 per cent phosphorus, and l ·5 per cent moisture. About 40 per cent of the total tonnage mined has come from surface stripping and on-shore mines. These areas have now been almost completely depleted, and operations are confined to submarine mines extending for two miles off shore under the waters of Conception Bay. Three sub-marine slopes are currently in operation, Nos. 3 and 4 working in the Lower Bed and No. 6 in the Middle Bed. A general picture of the workings is shown in isometric projection in Figure 1. Submarine mining has been entirely by the room-and-pillar method, with an extraction of 60 per cent. The deepest workings, at a vertical depth of 1,850 feet below sea-level, have a rock cover of about 1,500 feet. No mining is done in areas where the rock cover is less than 200 feet. To date mining has explored six square miles of a potential area that may exceed 50 square miles."

Jan 1, 1949

By Tom Demorest

SMART is an association of mining companies that meet regularly to coordinate the technology development needed by the mining industry. Since 1995, the member companies and institutions have directed research and influenced the manufacturers and suppliers to improve surface mining technology and services. SMART actively supports learning seminars, collaborative research projects, and user groups. Members of SMART include some of the major surface mining companies in North America and Australia. These companies have recognized the value that collaboration can bring to the needs of individual organizations as well as the global mining industry.

May 1, 2009

By Michel Brissette

"To recover more valuable ore and considering the complexity of minerals, the needs to grind finer is increasing. To reach the desired fine grinding targets, using the existing grinding media size, the energy consumption is increasing exponentially. As already proved at this conference, small grinding media represents the best potential to improve grinding efficiency. How do the small grinding media perform in industrial grinding mills?The use of small grinding media in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, smaller grinding media versus 25 mm media generate a power saving from 10% to 44%. In vertical stirred mills, the power saving increases from 20% to 60%. More potential savings have been identified.For the same operating conditions, how a vertical stirred mill is performing compared to ball milling? In regrind application, a vertical stirred mill with small media (5-12 mm Millpebs) will require at least 62% less energy than a ball mill charged with 25 mm grinding media.INTRODUCTIONIn some mining applications, fine grinding is needed to liberate further the valuable ore. The purpose of regrind mills is to achieve the last stage of grinding before final flotation stage: the cleaners. In part because of high prices of small grinding media as well as availability, the most widely used size of grinding media is 25 mm.When calculating the recommended ball top size from Bond’s formula (Bond, 1961), the size for regrind applications is much lower than 25 mm. Today, the barrier for small grinding media is broken. They are best suited in regrind application. The size of grinding media is one of the most important variables affecting the mill efficiency (McIvor, R., 1997; Nesset, J.E., Radziszewski, P., Hardie, C. & Leroux, D.P., 2006).Conventional ball milling was discarded for fine grinding because of its very poor energy efficiency (Zheng, J., Harris, C.C. & Somasundaran, P., 1994; Yan, D.S., Freeman, M. & Dunne, R., 1995). Therefore, new technologies as stirred mills were developed to grind finer more effectively. Three fundamental questions should be asked. What is the best fine grinding technology? What should be the best media size to use? Is it possible to grind finer by using less energy with the existing regrind equipment?"

Jan 1, 2009

By V Dolmage

Copper Mountain is the third largest copper mine in British Columbia, and is now producing close to 20 million pounds of copper per year, with which is recovered also 4,000 ounces of gold and. 13,800 ounces of silver. After a long and checkered career, during which the ownership and management changed several times, this deposit finally came into the possession of the Granby Consolidated Mining, Smelting and Power Company in 1923. It was not, however, until the end of 1925 that the mine, under the management of Charles Bocking and C. H. Smith, was successfully placed on a basis of profitable production. It is a low-grade deposit of the contact-metamorphic type, with refractory ores consisting of chalcopyrite and bornite in a gangue of altered andesitic and basaltic breccia. The ore is concentrated to a product carrying over 30 percent copper, which is smelted in Tacoma. The deposit is 12 miles south of the town of Princeton, which is on the Kettle Valley railway, 150 miles east of Vancouver and 40 miles north of the International Boundary line. Princeton is served also by a branch of the Great Northern railway, which leads clown the Similkameen, Okanagan, and Columbia valleys. Copper Mountain mine and camp are connected to Princeton by a good mo tor road extending up Wolf Creek valley, while the haulage level of the mine, which emerges on the steep side of the Similkameen valley 1,000 feet below the camp, is connected with Princeton by a spur of the Kettle Valley railway leading up the Similkameen canyon and passing en route through Allenby, where the concentrator is situated.

Jan 1, 1929

By Arnaud Faucher, Claude Bazin, Marilène Renaud, Mohamed Mai Manga

"Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action needed to minimize its impact on the process. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality. Recovery losses in downstream leaching or flotation circuits justify the effort in developing techniques for the detection of hydrocyclone malfunction. Two approaches for the detection of hydrocyclone fault are presented in this paper. The first proposed method uses the conventional sensors available in a grinding circuit allowing real time detection of hydrocyclone abnormal operation. The second technique is based on the use of vibration sensors installed on the hydrocyclone of a nest. This last technique enables the classification of the hydrocyclone malfunction as surging, overloading and plugged apex. The two techniques can be combined to increase the robustness of the problem detection.INTRODUCTIONHydrocyclones are used for many purposes ranging from water separation, fines removal and obviously for the preparation of the feed for subsequent concentration circuits in a mineral processing plant. The strategic role of the hydrocyclones for the preparation of the feed to the concentration circuit is often underestimated because of their simplicity of operation and robustness (Napier-Munn et al., 1996; McIvor, 1988). It remains that despite their simplicity, hydrocyclones have been studied extensively from 1970 to 1990 with the objective of developing mathematical models of their operation to be incorporated into grinding circuit simulators (Napier-Munn et al., 1996; Lynch, 1977; Flintoff et al., 1987). Such a development effort is already an acknowledgement of the importance of these units in a mineral processing plant. Several authors (Del Villar et al., 1996; Plitt and Kawatra, 1979; Casali et al., 1998) proposed soft sensors to estimate the classification efficiency of hydrocyclones using sensor measurements. However, few of the proposed sensors are used in the industry. More recently several papers were published to discuss the application of 3-D modelling of the hydrocyclones (Narasimha et al., 2005; Cullivan et al., 2004) and sensors (Bond et al., 1999; Neesse et al., 2003; Hou et al., 1998; Olson and Waterman, 2004; Williams et al., 1995; Willams et al., 1997) to help in the detection of hydrocyclone malfunction."

Jan 1, 2010

By A. Mazhary, T. Huff

Sensor-based ore sorting technology is a growing area of interest due to lower-grade ore deposits and higher costs of processing, among other reasons. Among the sensors currently utilized in the particle sorting industry, X-Ray Fluorescence (XRF), as the only sensor with elemental analysis capabilities, has always attracted more attention. Currently, the bench-scale amenability tests for this sensor are performed using hand-held XRF analysers. However, this testing method overestimates the performance of the XRF sorter, and therefore, the results from these tests can be misleading and are often mispresented. The work presented here was conducted on a copper mine and investigates how the sensor’s sensitivity to copper deteriorates under different testing methods. This work compares and correlates the results of an Olympus hand-held XRF analyser, static, and dynamic sorter responses with the actual grades of the rocks. The results confirmed that, the sorter response was extremely prone to blind spots. Furthermore, the results demonstrated that although the static sorter’s responses were comparable in terms of rock identification to those of the hand-held XRF analyzer and assays, the accuracy of the dynamic sorter response deteriorated both as a function of grade of the rocks as well as the potential for blind spots. INTRODUCTION Sensor-based sorting technology has been gaining increasing attention even by larger mining corporations as ore grades decrease, deposits get deeper and therefore cost of mining and processing increases. There are various types of sensors that are currently being used in the particle sorting industry such as X-Ray Transmission (XRT), Color, Electromagnetic (EM), Near-Infrared (NIR) and others. However, none of the sensors are capable of identifying and quantifying particles by the elemental content, except for X-Ray Fluorescence (XRF). XRF is a non-destructive, surficial analytical technique used to measure elemental composition of materials. X-ray fluorescence happens when a secondary x-ray (fluorescence) is released after a sample is bombarded by a primary x-ray source. From a sorting perspective, the most common and expected issues that are associated with XRF sorting are lower throughputs compared to other sensors due to particle presentation limitation as well as the need to wash the material before introducing to the sorter. However, one important issue that is mostly neglected is how the amenability tests are performed and how realistic the obtained results are. Current amenability test procedure utilises a handheld XRF analyser (such as an Olympus InnovX, as used in this work) on multiple, generally 4, sides of the rock and uses the average measured grade as a criterion for separation. While this is a widely accepted technique, it fails to consider some important factors such as exposure time and the distance between the sensor and the particle. These factors can significantly affect the sorting outcome.

Jan 1, 2019

By B. H. Kim

It is hypothesized that the standard approach adopted to characterize the ground and to determine the rock strength properties at depth are flawed and generally tend to underestimate the rock strength and possibly the stiffness, particularly when the rock mass is characterized as massive to moderately jointed or blocky to very blocky. It is therefore necessary to conclusively established that the hypothesis, that the rock strength in highly confined rocks is greater than generally anticipated, is actually valid and generally applicable, and then to develop new procedures to establish rock parameters that can be reliably used for the design of deep excavation.

May 1, 2009

By P. Chaddock

The Thompson Mill has a capacity of 15,000 T ID of ore and produces two grades of nickel concentrate, copper concentrate and occasionally graphite concentrate. Up to July of 1985 we processed two distinct ore types: T-1 ore, averaging 2. 8% Ni and . 2% Cu and Pipe Open Pit ore, averaging . 8% Ni associated with peridotite and serpentine. Presently our ores from T-1 mine and Thompson Open Pit are of the same type and are processed together. (Figure 1)! n October, 1982, we decided to install an Outokumpu Courier 300 on-stream analyser on an initial 6 streams. The equipment was delivered to the mill on May 2, 1983 and the first analyses were generated by June 17th. The calibrations were 35% complete by the mid-July summer shutdown and were completed in the fall. 1. 2 Analyser Slurry Feed System:The key to successful on-stream analysis is delivery of the sample streams to the analyser.Our system uses pressure-thief sampling for collection. (Figure 2) Initially we used thief samplers modelled after the Outokumpu design, with turbulence bars upstream of the collection point. These units have been replaced with simple laterals as they have worn out. Our thief samplers are mounted vertically on pump discharges and we believe sufficient turbulence exists to ensure representative sampling.

Jan 1, 1987

By S. Kelebek, C. Gibson, M. Aghamirian

"Global niobium production is currently dominated by three operating mines, Araxá and Catalão in Brazil, and Niobec in Canada. Although over 90% of the world’s niobium is mined and processed in Brazil, a number of high grade niobium deposits exist worldwide. The advancement of these deposits depends largely on the development of operable beneficiation flowsheets. Pyrochlore, the primary niobium bearing mineral, is typically upgraded by flotation with amine collectors at acidic pH, and often includes a reverse gangue flotation stage prior to pyrochlore flotation. Challenges related to the flotation of niobium ores include complicated flowsheets which require pulp pH adjustment from alkaline to highly acidic conditions, difficulty recovering fine grained pyrochlore, producing concentrates that meet specifications, and minimizing the losses to reverse pre-flotation gangue concentrates, slimes, and tailings. The specific flotation challenges associated with different niobium ores are discussed. In some cases, the use of alternate flotation reagents and flowsheets are required to achieve reasonable gangue rejection and maximize recovery, particularly of very fine pyrochlore grains.INTRODUCTIONNiobium is a transition metal primarily found in the oxide minerals pyrochlore (Ca,Na)2Nb2O6(OH,F) and columbite (Fe,Mn)Nb2O6. After physical upgrading, pyrochlore is converted into a ferroniobium product which is largely used in the production of high strength low-alloy steel. Today’s niobium market is dominated by the Companhia Brasileira de Metalurgia e Mineração, whose Araxá operation produces over 80% of the world’s niobium. There are two smaller operations, Niobec in Canada, and Catalão in Brazil, which account for the remaining production (U.S. Geological Survey, 2013).A number of niobium deposits exist globally, their advancement dependent on the development of operable beneficiation flowsheets. Pyrochlore, the predominant niobium bearing mineral, is commonly upgraded by flotation with cationic amine collectors in acidic pulp conditions. However, many niobium ores do not respond to this typical flowsheet because they are either highly refractory or niobium deports to other minerals such as columbite, ilmenite and rutile, which are not as responsive to this reagent scheme (Bulatovic, 2010). Other reagents, such as alkyl hydroxamic acid, have been studied extensively and while promising, are not without their own inherent issues including lack of selectivity over iron oxide minerals, and high addition rates (Ni & Liu, 2012; Gorlovskii, Eropkiny, Koval, Strelstin, Khobotova, & Shtchukina, 1968; Gorlovskii, Khobatova, & Shtchukina, 1966).It is the aim of this report to highlight the challenges associated with the physical upgrading of niobium minerals through examination of the flotation behavior of two different ore systems. In order to overcome these challenges it is important to thoroughly understand the limitations of typical flowsheets/reagent schemes currently employed in operation."

Jan 1, 2015

By L. M. Scovell

The Internet and its related technologies will radically change the way that mines manage and control their maintenance, repair, and operating supply chains. The Internet is creating new distribution channels and offers new technology platforms with significant advantages over more traditional methods. Mines will have to re-evaluate both the strategies and the tactics employed in these areas. Mines will use e-commerce to integrate their maintenance, repair, and operating supply chains. The integration will extend beyond traditional trading partners to a worldwide network of communities with similar interests and goals. The changes will transform the way mines operate, lower mining costs, and thereby increase their chances of success in an increasingly competitive environment.

Jan 1, 2000

By Richard F. Lynch, Frank E. Goodwin

"The development of Galfan, a new generation 95% zinc-5% aluminum-mischmetal alloy coating for steel, offers opportunities for greater fabrication flexibility and upgraded corrosion performance in automotive applications. The formability of Galfan is equivalent to that of electrogalvanized steel, based on laboratory tests and automotive component fabrication. Corrosion resistance of Galfan exceeds that of hot dip and electrogalvanized, including performance in automotive industry tests. Automotive production applications for deep drawn and stamped components in France and Germany are based on the ability to meet dual performance requirements for upgraded formability and corrosion resistance. The first U.S. Galfan application was on 1985 model Ford cars and light trucks for transmission oil cooler lines which has now expanded into a number of power steering tubing uses. IntroductionContinuing requirements for improved vehicle performance coupled with the ever present need for reduced cost have spawned the development of a number of new coated steel products. Among this new generation of coated steels is Gaifan™, a 95070 zinc-Solo aluminum-mischmetal hot dip alloy coating. Galfan exhibits particular promise for automotive use based on broad fabrication advantages and upgraded product performance(I ),The unique characteristic of Galfan is the key combination of greatly improved formability with much longer corrosion life. Galfan provides significantly better formability than any other hot dip coating. Testing shows that formability is limited primarily by the steel substrate to which the Galfan coating is applied. Galfan exhibits excellent resistance to flaking and microcracking during commercial forming operations. The result is the elimination of unnoticed damage to the coating which would show up later as premature rusting on the finished product."

Jan 1, 1987

By R. Stauffer, S. Lindsay

"Sherritt Gordon Mines Limited utilizes pressure hydro-metallurgical techniques to recover nickel, copper and cobalt from su1phidic concentrates, mattes and various other metal-bearing materials.A brief description of the nickel refinery operation is given. In the nickel refinery process, an ammonia pressure leach is employed to treat the feed materials to dissolve the non-ferrous metals as their respective ammine complexes. The resulting leach solution goes through a series of steps which removes copper as copper sulphide and further purifies the solution prior to nickel precipitation by hydrogen reduction. The reduction end solution, containing the cobalt which was originally present in the leach solution as well as residual nickel, is treated with hydrogen sulphide. The resulting nickel-cobalt sulphide precipitate feeds the soluble cobaltic ammine process, which separates the nickel and cobalt and recovers the cobalt as a pure powder.A detailed description of the cobalt recovery process is given. Included are the various steps, comprising: acid leaching of the mixed sulphides, solution purification, ammine complex formation and cobaltous oxidation, two-stage nickel precipitation, cobalt conversion and reduction. A brief description of cobalt powder handling is included, along with typical physical properties and chemical analyses of the cobalt product. In general, the purpose of this paper is to describe the present plant practices employed in the recovery of cobalt as a by-product of the nickel refinery operations."

Jan 1, 1967

By André Chagnon, Yvon Héroux

"Résumé - Cette étude porte sur l'altération de la matière organique et des argiles dans les boues carbonatés dévoniennes du faciès ""F"" de la Formation de Pine Point et ses équivalents stratigraphiques la Formation d'Evie et l'unité bitumineuse de la base de la Formation de Horn River. La matière organique se compose principalement de bitume solide et de quelques fragments de fossiles (organo­ clastes). La majorité des échantillons ne renferment que de l'illite et des interstratifiées illite/smectite.Si on compare les températures d'homogénéïsation (Th = l00°C) des inclusions fluides de la sphalérite et des dolomites associées à la minéralisation aux températures estimées à partir de la réflec­ tance de la collinite (84°C à ll7°C), l'on ne peut pas conclure à la présence d'une anomalie ther­ mique dans le district minier de Pine Point. De plus, la réflectance des organoclastes n'est pas plus élevée dans le district minier de Pine Point que dans les localités plus éloignées des gîtes. L'analyse des minéraux argileux conduit à la même conclusion : aucune anomalie thermique n'est décelable dans les unités échantillonnées à l'intérieur du district minier de Pine Point quelque soit l'indicateur utilisé.La kaolinite et la matière organique altérée, affichant des valeurs anomales de sa réflectance, se trouve essentiellement en présence de soufre et de sulfures. Cela suggère une origine authigène de la kaolinite et une altération de la matière organique reliées au phénomènes de minéralisation.Abstract- The alteration of organic matter and clays is studied in the Devonian Pine Point Formation carbonate muds, ""F"" facies, and its lateral equivalents the Evie Formation and the biturninous unit at the base of the Horn River Formation. The organic matter is mainly composed of solid bitumen with few fossil fragments (organoclasts). Most samples contain only illite and mixed layer illite/smectite.If we compare the Th(l00°C) from fluid inclusions of sphalerite and dolomites associated with mineralization to the temperatures calculated from the reflectanœ (Ro) of the collinite (84°C to 117°C), we cannot detect a thermal anomaly in the Pine Point mining district. This result is based on the reflectance values of organoclasts from the mining district that are not higher than those reflectance values measured on organic matter (OM) away from the ore deposit. A similar conclusion is reached from the clay study: none of the parameters used allow us to identify a thermal anomaly in the samples from the mining district.The kaolinite and the altered OM showing anomalous Ro values mainly occur with sulfides and sulfur. This association suggests an authigenic origin for the kaolinite and an alteration of the OM due to the mineralization events."

Jan 1, 1994

By N. Hmidi, T. Yalcin, M. Papadakis, B. Hilscher

Mill tailings, containing iron sulphides in particular, pose an environmental concern since they constitute a potential source of acid mine drainage which can damage vegetation, harm soil and living organisms, and contaminate groundwaters. Proper disposal of acid generating tailings is therefore an important issue that must be addressed and resolved in a satisfactory manner. Placer Dome Canada operates a 4000 t/d gold cyanidation facility at Musselwhite mine, in northwestern Ontario, where the mill tailings have been classified as acid generating. This study was conducted to explore the effectiveness of froth flotation in removing the sulphide minerals from these tailings and producing a low-sulphur, non-acid generating material that could serve as a capping material for previously deposited tailings. Laboratory semi-batch flotation tests were carried out in accordance with an experimental design procedure, and a computer simulation program was developed to facilitate the evaluation of flotation performance. In this investigation, pH, collector concentration, and airflow rate were considered as the relevant flotation variables, and their effects were examined both experimentally and by simulation. Results have demonstrated that flotation can successfully desulphurize the Musselwhite mine tailings and render them non-acid generating.

Jan 1, 2004

By H. Pempel, J. Markowski, P. Ay

"Metal-coated thermoplastic parts find more and more functional and aesthetic applications in the interior and exterior of cars. The vapor-deposited or electroplated coatings are usually composed of a plurality of nickel- and chromium-containing layers, which are applied to copper-containing carrier layers on the polymers. Previously, recycling processes are mainly focussed at the recovery or thermal utilization of the plastics. Targeted and selective recycling of the metallic coatings is usually not carried out. Together with several SME, BTU developed a process, in which a complete and separate recovery of all components in high purity is possible with biotechnological methods. The bioleaching is carried out with iron and sulfur-oxidizing bacteria, especially Acidithiobacillus ferrooxidans. The copper-containing layers are dissolved in the solution; chromium- and nickel-containing particles are precipitated as solids. After the bioleaching, a mechanical separation of the individual metal-containing components and their separate workup are carried out. End-products are metallic copper, a nickel- and chromium-containing solid and the cleaned plastics. The bioleaching ensures a high purity of the end products. Through the use of bacteria, which are also found in nature, the process is environmentally friendly. Compared to chemical leaching using inorganic acids, considerably shorter leaching times can be achieved. In addition to the optimization of the leaching process, the R/D-project also includes the development and testing of the apparatus technology.INTRODUCTION The material complexity of many end-user products has increased in recent years, especially in the fields of electrical appliances, vehicle technology and medical technology. However, the demands on functionality, safety, comfort and energy efficiency still play a greater role in product design as factors such as sustainability and usability. For example, if a car still holds more than 70% of steel in the 1980s, a vehicle nowadays includes a larger proportion of a variety of difficultly separable plastics and composite materials, as well as complex metal composites. This relates in particular to composites made from such different materials as metals and plastics. The processing and recovery of the components of those complex material mixtures is difficult for recycling companies."

Jan 1, 2017

By C. Gosselin, G. M. Payenzo, C. Bazin, M. Desnoyers, G. Chevalier

"ArcelorMittal Mines Canada operates hydraulic classifiers to reduce the silica content of an iron oxide concentrate from 4.5% to less than 1.2% SiO2. Sampling campaigns were conducted to develop a preliminary model for the hydraulic classifier. Results show that iron oxide and quartz are respectively concentrated in the coarse and fine size fractions of the classifier feed. The mineral partition curves in the classifier and the size distribution of the minerals in the feed are used to simulate the classifier operation in order to identify the source of variability observed in the daily plant production data. Results indicate that most of the variation is probably caused by unsteady operating conditions of the classifiers.INTRODUCTION Hydraulic classifiers are a class of gravity separation devices (Wills, 1992) used to classify particles according to their size and specific gravity. Hydraulic classifiers also known as density separators (Hearn, 2002) combine hindered settling and upward flow of water to selectively entrain light particles to an overflow stream. Denser particles settle to an underflow stream. Hydraulic classifiers are used for various purposes ranging from cleaning of coal (Das, Sarkar, & Mehrotra, 2009), recovery of chromite from plant tailings (Kumar, Tripathy, & Rao, 2009) to upgrading iron oxide concentrate (Hearn, 2002). ArcelorMittal Mines Canada operates several hydraulic classifiers to upgrade an iron oxide concentrate by removing fine quartz and other light minerals from hematite that is the main iron oxide mineral. A project was initiated to analyze the operation of the classifier in an attempt to identify the source of the variability in the production results and to assess the potential of increasing iron recovery in the classifier. One possible disturbance for the classifier operation is the change in the classifier feed composition and size distribution, while the other considered disturbance is the operation of the classifier. The paper is divided into five sections. The first section summarizes the ore processing sequence for the production of iron oxide pellets to identify the position of the hydraulic classifier in the process. The second section describes the hydraulic classifier. The third section discusses the sampling campaigns conducted on the hydraulic classifier. The method used to process the data from sampling, the results of the data processing and simulation of the classifier are discussed in the remaining sections."

Jan 1, 2012

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019

By Songgen He, Jianchun Guo

With the development of complex, unconventional and deep reservoirs, it shows that many rocks behave plastically with the influence of clay and confining pressure. Traditional linear elastic hydraulic fracturing initiation models are not good predictors for elastic-plastic reservoirs. With the deformation theory of plasticity, a power hardening constitutive equation was developed in piecewise approximation method. Based on the nonlinear constitutive equation, a model of the stress field around the wellbore was developed considering fracturing fluid penetrating effect and in-situ stress anisotropy. At last, coupled with the maximum tensile strength criterion and Mohr-Coulomb criterion, a new elastic-plastic hydraulic fracturing initiation model was built. The following conclusions were summarized in the paper: (1)The piecewise power hardening constitutive equation based on the deformation theory of plasticity can accurately describe the nonlinearity of elastic-plastic deformation. (2)Whether the rock is yielded or not is determined by in-situ stress, yield stress, Biot coefficient and pore pressure. (3)Plastic yield has little influence on radial stress but significant impact on circumferential stress. The radius of the plastic zone is positively correlated with in-situ stress but negatively correlated with yield stress, power hardening index, pore pressure and Biot coefficient. (4)Initiation modes include tensile failure and shear failure when rock is yielded. (5) For elastic-plastic reservoir, the initiation pressure predicted by linear elastic model is much lower if the rock is yielded.

Jan 1, 2015

By G. J. Ackland, K. Saksl, F. Brunke, M. Kohnke, B. Tegner, C. Siemers

The application of titanium alloys is limited to 550°C due to their poor oxidation resistance. It is known that the addition of niobium decelerates the oxidation of titanium alloys whereas elements like vanadium do not improve titanium’s oxidation resistance. The underlying mechanisms are not yet well understood. In the present study, different binary titanium-niobium and titanium-vanadium alloys as well as commercially pure titanium were investigated. Oxidation experiments were carried out at 800°C up to 288 hours followed by metallographic analyses to study the oxide layer morphology as well as the microstructure at the interface. Energy-dispersive X-ray spectroscopy mappings were used to identify possible changes in the distribution of the alloying elements. In addition, micro-focused hard X-ray experiments were performed to layer-wise analyse the phase composition in selected samples. As expected, the niobium containing alloys show a better oxidation performance compared to commercially pure titanium and the titanium-vanadium alloys. The oxide layer consisted of TiO2 and Ti2O3. Depending of the niobium content, a niobium-rich layer developed below the metal-oxide-interface minimising oxygen diffusion into the titanium matrix. Based on these results, the minimal niobium content needed for improved oxidation resistance was identified so that alloys of technical relevance can now be developed.

Jan 1, 2014

By Gavin C. Dirom

? The Mining Association of British Columbia (MABC) was established through an Act of Parliament in 1901 ? The MABC represents the interests of B.C.?s ? Coal and mineral mining companies ? Smelting companies ? Advanced stage development projects ? Key areas of work: ? Environment, Health and Safety ? Policy & Government Relations ? Knowledge and Information Services

May 1, 2008