Search Documents

By T. Crivits, I. Bellemans, K. Verbeken

In the metallurgical industry, furnace cooling is often employed to enhance furnace lifetime. Hence, the pyrometallurgical phase comes in close contact with a non-air coolant. The proximity of the pyrometallurgical phases to the coolants may lead to dangerous situations. In case of a breach of the cooling circuit, the contact between a hot and a cold liquid may cause a vapour explosion. The outcome of this vapour explosion includes a pressure wave which could result in damage to the furnace, bodily injuries or even casualties. To prevent such dramatic events, the origin of vapour explosions is currently being studied in more detail. For this purpose, OpenFOAM was used to perform Computational Fluid Dynamics (CFD) simulations. In a first step, simulations were run to get a better idea of the influence of the compressibility on the simulations. The obtained results help in getting a better insight on the need of computational power, and possible numerical errors using compressible or incompressible solvers in future simulations. In a second step, systems without vapour explosions were simulated and compared to experimental results with mercury and aluminum. INTRODUCTION Humanity started using metals for tools around the Chalcolitic (~7400 cal BC), when copper was melted in small furnaces (Radivojevic, Rehren, Farid, Pernicka, & Camurcouglu, 2017). Nowadays, metallurgy has grown into a major industry and it has become impossible to imagine society without metals. In the pyrometallurgical industry, coolants (low temperature liquids, for example water) and pyrometallurgical phases (high temperature liquids, such as slags, mattes and alloys) are typically present in close proximity of each other. The interaction between these two phases can have catastrophic consequences (Tveit et al., 2008; Ferguson & Zsamboky, 2017). A vapour explosion may occur as the consequence of the rapid evaporation and expansion of the coolant. Whereas the volume of a gas increases linearly with the temperature (approximately a factor four by heating from 100°C to 1300°C), a simple calculation of the ratio of the two specific volumes shows that evaporation causes the volume of water to increase by a factor of 1700 at 100°C and ambient pressure (Table 1 and equation (1)), a number that was also found in literature (George, Nexhip, George-Kennedy, Foster, & Walton, 2006). The volume change occurs so fast that it resembles an explosion, hence the name vapour explosion. Such an explosion at industrial scale can cause economical losses, bodily injuries or even fatalities.

Jan 1, 2019

By A. J. Smethurst, S. B. Hearn, S. Boskovic

"The problem of crud in solvent extraction is well known and can be a major handicap and operational issue. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Flocculation can be utilized to remove some of the troublesome particulates but colloidal silica does not flocculate well and presents a different problem requiring innovative chemistry to solve. Coagulants can assist by facilitating the removal of this colloidal silica by promoting the agglomeration of the particles to a size which can be more readily settled or flocculated in solid/liquid separations. This is achieved when the coagulants bind to the surfaces, displacing water and destabilizing the colloids, whereupon they bind to each other which facilitate their amenability to conventional flocculation.INTRODUCTIONSilicate minerals are abundant in the upper layers of the Earth’s crust, and there are few mineral deposits without significant levels of gangue silicates. Silicate minerals include the pure silicas, such as quartz and other silicate containing minerals such as clays, chlorites, feldspars, as well a vast number of less common silicates.During the acid leaching of ores, two types of fine silica particles are released in solution from the dissolution of the host mineral. The first consists of partly depleted silicates, and the second is colloidal silica, which forms in solution. It is this second type which has the potential to cause crud formation as well as poor solution clarities, slow filter rates and excessive flocculant usage (Figure1)."

Jan 1, 2016

By P. D. Duever, P. J. Readyhough, P. L. Silveston

"The Plastojrost apparatus, developed by Ritter and Juranek in the 1960s has been modified primarily, to automatic temperature control. A limited investigation of carboniferous and cretaceous coal samples showed that both coals undergo the same changes when coked in the Plastofrost unit. Dilatometer plastic range and total dilatation correlated well with the Piastofrost plastic range for the carboniferous Appalachian coal, but not for the cretaceous western Canadian coal. Work to elucidate the characteristics of some western Canadian coals using the Plastofrost is in progress. IntroductionCoke quality is critically affected by the properties of the plastic phase in the coal-to-coke transformation. Since these properties exist in a coke oven and are not measurable, they are approximated by standard laboratory tests, such as free swelling index, plastometry, and dilatometry. Of particular interest to us is the anomalous behaviour of western Canadian coals of cretaceous origin. By many predictive methods, these coals should not produce coherent cokes. When coked in pilot scale test ovens, in fact, they produce cokes of good stability. They typically make up 20% of Japanese coking coal blends and are also used in South Korea, Mexico, Brazil, and several European countries. This anomalous behaviour has been studied in our laboratory<8.9.1O). Plastic properties or rheological tests examine just the external ramifications of the coal-to-coke transformation. To understand the process, however, microscopic examination of the coal and coke seems to be needed. The Plastofrost unit has been shown to be a convenient means to this end."

Jan 1, 1987

By L. C. Galloway, G. L. Tiley

"Mine hoist brakes must meet the following statutory performance criteria:- There should be two independent braking systems; at least one should act directly on the hoist drum.-If one brake fail s, the others should be able to retard and stop the hoist safely before the descending conveyance, carrying the rated load, reaches any obstruction.- When all brakes apply, decelerations should not be so violent that men travelling in the conveyance are injured.- The brakes shall not overheat and fade during an emergency stop.This paper discusses design principles and capacities of caliper and disc type brakes, when applied to double drum and friction hoists of equivalent capacity.IntroductionThis paper is about the brakes that are used on mine hoists; their functions, especially in emergencies, typical design, and how they are operated, controlled, tested, and adjusted.There are two basic types of mine hoists:1. Drum hoists, where the ropes are attached to, and coil on drums. The simplest system has only one drum. Most such hoists, however, have two drums, attached to a common shaft. Ropes are wound on each drum in opposite directions, so that when one conveyance is being raised, the other is lowered. The conveynaces may travel in vertical or inclined shafts. In the latter case, the hoist s are referred to as slope hoists.2. Friction hoist s, where the headropes are not attached to the wheel, but are in contact with it for an angle of lap of, typically, between 180 and 195 degree s. Forces are transmitted from the hoist wheel to the head ropes by friction.The lower ends of the conveyances are connected to balance ropes , approximately the same weight per foot as the headropes."

Jan 1, 1986

By M. B. McClenaghan

"The Matheson area of northeastern Ontario is of great interest for mineral exploration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has become an important exploration method. The Ontario Geological Survey&apos;s Black River-Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift (< 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (> 3.3 S.G.) and fine (- 250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (< 50 um) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of = 3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By R. Pérez, James A. Finch, F. Tavera, Cesar O. Gomez

"Gas holdup is a variable which affects the operation of flotation columns. On one hand, gas holdup is a function of bubble size (a function of sparger type, frother characteristics and concentration, and air flowrate), tailings flowrate, solids content, and mixing patterns in the collection zone. On the other, gas holdup defines flotation kinetics and carrying capacity. Therefore, gas holdup is a useful variable to control and diagnose the operation of a flotation column, but the lack of a reliable sensor for on-line gas holdup monitoring has prevented its use in industry.This work describes the principle and the practical difficulties associated with the development of a gas holdup sensor based on the measurement of the electrical conductivity of dispersions. Two different approaches have been devised. These approaches will be described and test results presented of prototypes in laboratory and industrial columns.Background.Several years ago, a research program was initiated at McGill to use electrical conductivity as the basis for developing sensors for process measurements in mineral processing. Electrical conductivity is an intensive property which is a function of the concentration of the different phases present in a dispersion. The initial focus was on the detection of the interface between two dispersions with different characteristics (i.e., that between the collection and froth zones in flotation columns or that between clear water and sedimented solids in thickeners). The technique works in this case by searching for the location at which a sudden change in specific conductivity occurs, as a consequence of different gas holdup or solids content, and absolute values of the specific conductivity of the dispersions involved are not necessary1,2."

Jan 1, 1995

By Y. Wang, J. D. Miller, C. L. Lin, Virginia Tech

Conventional flotation machines are typically limited to a particle topsize of 150-200 microns due to inherent constraints created by the pulp and froth phases. To overcome these limitations, a novel fluidized-bed flotation system called the HydroFloatTM Separator has been developed specifically for the purpose of floating coarse particles containing only small amounts of exposed hydrophobic minerals. Over the last decade, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3,000 microns diameter. More recently, sulfidebased test work has shown that this novel device is also capable of recovering metalliferous values at a grind size that is much coarser than currently used in industrial concentrators. In the current study, high resolution X-ray microtomography (HRXMT) was used to experimentally compare the degree of exposed grain surface area necessary to recover coarse particles using the HydroFloatTM technology to that attainable using a traditional mechanical flotation cell. The data indicate that exposed grain surface area is a critical factor for coarse particle flotation. For the gold-bearing sulfide ore examined in this study, the HRXMT data suggest that near complete recoveries of coarse (850x500 µm) multiphase particles containing as little as 1% exposed grain surface area were realistically attainable using the HydroFloatTM technology. As such, this new technology may offer a unique opportunity for increasing concentrator capacity by increasing the primary grind size needed for rougher/scavenger separations.

Jan 1, 2016

By Stephen D. Butt

Presentation Outline Overview of abandoned mine workings problem. Outline project phases and major outcomes. ? Phase 1 ? Assessment of current imaging technology ? Phase 2 ? Prototype technology development. ? Phase 3 ? Proof of concept ? Montague Gold Mines field trials. Research status - summary of ongoing and future work.

Apr 1, 2005

By A. M. Cann, C. I. Godwin

"The Kemess porphyry copper-molybdenum deposit occurs in the Intermontane Belt of north-central British Columbia. The deposit is in andesitic to basaltic flows and tuffs which may be correlated with the Savage Mountain Formation of the Upper Triassic Takla Group. Most known chalcopyrite and molybdenite is associated closely with a 500-m-diameter zone of intense quartz-sericite-pyrite alteration. A zone of supergene enrichment, up to 30 m thick, underlies a leached capping about 20 m thick. The age of mineralization and the surrounding granodiorite and quartz monzonite pluton is Early Jurassic. K-Ar and Rb-Sr analyses indicate that the mineralization and alteration is slightly younger (l82±6 Ma) than the granitic intrusion (KAr: about 205±6 Ma; Rb-Sr: 190±4 Ma). The low 87Sr/J6Sr initial ratio for the granodiorite is typical of plutons in the Intermontane Belt.IntroductionKemess is a medium to small porphyry copper-molybdenum deposit with significant gold and silver values (Pilcher and McDougall, 1976). This paper describes the lithologies and alteration at this property; geochronology by Rb-Sr and K-Ar methods defines the ages of mineralization and surrounding plutons to be Early Jurassic.The property, located in the Thutade Lake area of northcentral British Columbia (NTS Map 94E; lat. 57°04&apos;N; long. 126°44&apos;W), is about 425 km northwest of Prince George (Fig. 1). Closest road access is 35 km southeast of Kemess. Final access must be by float plane or helicopter. The British Columbia Railway right of way passes 70 km to the southwest of theproperty.A prominent gossan zone at Kemess was staked in 1967 by Kennco Explorations (Western) Ltd. following detection of geochemical anomalies during stream sampling the previous year. During 1968, 1969and 1971, Kennco completed 232 m of X-ray diamond drilling, conducted geological mapping and carried out geochemical sampling of silts and soils (Stevenson, 1969; B.C. Ministry of Energy, Mines and Petroleum Resources, G.E .M., 1969 and 1971). Getty Mines Ltd. optioned Kemess in 1975and 1976. They remapped the area and diamond drilled 12 BQ and NQ holes, totalling 2065 m (B.C. Ministry of Energy, Mines and Petroleum Resources, Expl. B.C., 1975)."

Jan 1, 1980

By S. R. McCutcheon

"The regional stratigraphy of the Lower Carboniferous Windsor Group in the Moncton Subbasin indicates that evaporites could be present in the Marysville Subbasin, part of what was formerly called the Central New Brunswick Platform. The Windsor Group consists of basement-fringing, algal build-ups (Gays River Formation), in places with intercalated siliciclastics (Parleeville), which are laterally equivalent to deeper-water, very thin to thinly bedded, euxinic limestone (Macumber). The Macumber is overlain by stratiform, nodular to mosaic anhydrite (Upperton) that is hosted by carbonate or calcareous siliciclastics. The sulphate also is equivalent, in part, to the algal buildups. Deep-water salts (Cassidy Lake) which overlie and in places are laterally equivalent to Upperton rocks have a basincentre distribution. The Windsor Group is overlain by shallow water evaporites and mudstones (Clover Hill) or by greenish grey mudstone (""transitional beds""). The paleogeographic distribution of these rocks provide important clues that help predict where deposits of salt and potash can occur.IntroductionCurrently there are three known potash deposits in southern New Brunswick (2, 3 and 4, in Fig. I). All three deposits occur in the Windsor Group of the Moncton Subbasin, but until recently their exact stratigraphic position within the group was not known.The Windsor Group is a cyclic sequence of carbonates, evaporites and red beds that is up to 1.0 km in thickness (Schenk 1969, p. 1038). It is Late Mississippian (Visean) in age and the type area is near Windsor, Nova Scotia. The group was named by Dawson (1873) but the rocks were described earlier by Hartt (1867). Dawson (ibid.) was the first to assign rocks in southern New Brunswick to the Windsor Group."

Jan 1, 1983

By Jacques Ouellet

Outline What is Microwave energy Investigation of transparency of 40 minerals Melting of Andesite in a MW oven Numerical modeling /Computer Simulations o FEM analysis ?? Some laboratory experiments o Particle Modelling Mw Application to Rock Breakage o A MW Rock Drill Prototype Conclusions What is Microwave energy Microwave energy is an electromagnetic wave consisting two electronic & magnetic wave traveling perpendicular to each other and transporting energy with the speed of light.

May 1, 2008

By Ainul Akhtar, Steve Cockcroft, Daan Maijer, Carl Reilly, Lu Yao, Jun Ou

A coupled thermal-fluid flow-multicomponent model has been developed to aid in understanding the melting/dissolution behavior of solid Al-rich Material (TiAl) in a liquid titanium pool produced by an electron beam. The model is capable of accounting for the significant phenomena present affecting heat, mass and momentum transport including thermal and compositional buoyancy and Marangoni forces, Darcy attenuation, evaporation, melting and solidification, and the associated release or absorption of latent heat. The modeling results have indicated the compositional fluid flow driving forces (compositional buoyancy and Marangoni forces) contribute significantly to the melting/dissolution process. The model is waiting for validation against empirical data.

Jan 1, 2014

By R. Erpelding

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By Jack A. Caldwell

"This paper describes the nature of stage curves and the ways in which they have been used to study the construction sequencing of tailings impoundments. They provide a simple graphical method of representing the main aspects of an impoundment, studying the effects of different impoundment geometries, and predicting and controlling impoundment operations.IntroductionThe designer o f a tailings impoundment must, at all stages of design, examine the relations hip between the volume o r tones of tailings that will be deposited at the impoundment, the height to which the tailings will rise in a given time and that rate at which the various parts of an impoundment will be constructed. The operator, if he is to keep proper control of this impoundment, must be able to examine the effect of different deposit ion rates at the impoundment, and the consequences of placing more or less tailings at different parts of the impoundment. The operator must be able to see at a glance just how much higher an impoundment will be at the end o f the following yea r of deposition, and this he must be able to do in order to formulate his annual construction and operating plans.Stage curves are the best way o f modeling an impoundment. The simple impoundment model represented by the stage curves enables the designer and operator visually to examine the relationships between the various factors, such as impoundment volume, deposition rat e and construction rate, that dictate the essential features o f impoundment design and operation.A design model for a tailings impoundment may be formulated as in Figure 1. This involves the site selection process, the definition o f a geotechnical model, a water balance model and a height-capacity-production model."

Jan 1, 1983

By Leon C. Botham

?? Review of Requirements ?? Components of Modeling ?? Water Management ?? Tailings Management ?? Primarily a water management problem ?? Solids relatively easily contained ?? Process flows and runoff a continuous stream over life of mine ?? Need to allow this to safely happen over wide range of conditions

May 1, 2008

By P. MacPhail, G. S. Dobby, I. M. Flint

"The objective of the laboratory work described in this paper has been to develop a method f or producing small gas bubbles at moderate to high gas rates in a flotation column. Small bubbles are particularly important for attaining reasonable flotation rates of fine particles. An ultrasonic aerosol generator has been employed to add frother solution directly to the gas stream. Using porous glass and filter cloth spargers, aerosol frother addition has produced bubbles at 1/2 to 2/3 the diameter of those produced by conventional frother addition to the liquid, at a lower frother consumption.IntroductionGas bubbles are generated in a flotation column most commonly by forcing gas through a porous medium called a sparger. Typical sparger material includes rubber (pierced with small holes) , fabric (such as filter cloth), fritted glass, or porous metal (steel or bronze) . Solid sparger material is suitable for laboratory use; however, for industrial applications a flexible sparger such as rubber or fabric is necessary to prevent the eventual plugging of orfices with solid particles and/ or precipitates. An exception to this is the use of a gas liquid contactor external to the column in combination with pressure release of gas in water, a method that has been demonstrated to produce very small gas bubbles. The typical objective of bubble generation for flotation column purposes is to produce bubbles with diameter of about 0.1 cm (and less) at a gas superficial velocity of 1 cm/s to 3 cm/s. In general, the smaller the bubble, the better. In man y cases, though, there is little , or nothing, gained by generating bubbles less than about 0.05 ern in diameter.Several factors affect bubble size when generated by a sparger: gas rate, orifice diameter, sparger surface area, surfactant type, surfactant dosage, and static head. At very low gas rates bubble diameter is independent of flow rate and is proportional to orifice diameter. At the moderate gas rates encountered in flotation columns bubble diameter, db&apos; is related to gas flow by: db oc vg n, where vg is superficial gas velocity (rate of gas flow per unit column area). For porous steel and filter cloth, n has a value of about 0.25 for vg between 0.2 cm/s and 2 cm/s(2). The magnitude of the effect of orifice diameter at these gas rates is unclear. The effects of frother type and concentration on bubble size issuing from a single orifice have been measur ed by Miagkovaru , shown here in Figure I(IS). The reduction in bubble diameter upon surfactant addition is due to the lowering of interfacial tension created by adsorption of surfactant at the gas liquid interface."

Jan 1, 1988

By Richard Dawson

Presentation Outline? Northeast BC Coal Fields Overview and History ?New mines and projects in development ?Design Issues for steeply dipping footwall slopes ?Design issues for angle-of-repose waste rock dumps

May 1, 2006

By A. C. Headon, K. W. Lam, D. P. Dautovich

"Microbiological activities affecting the performance of materials have been encountered in diverse situations within Ontario Hydro. Case histories of bacterial problems which are presented include ground rod corrosion at transformer stations, corrosion of a bare steel cooling water intake structure in Lake Huron and corrosion of steel components in a nuclear generation station vacuum building. Possible microbiological activities which may affect the corrosion behaviour of containers for the disposal of nuclear fuel waste in the future are discussed, as are bacterial actions suspected of causing an odour problem in residential water heaters.IntroductionBacteria are ubiquitous. Except by use of sterilization methods, bacteria -free environments are no t possible to find. Bacteria lie dormant in hostile environments, spread easily through air and water currents and reproduce rapidly under favourable conditions. Although different types of bacteria have different preferable conditions for growth, they are highly adaptive and in general, whenever there is a source of water and carbon (carbon dioxide or organic matter), there will be bacterial activities . These activities often induce or enhance costly metallic corrosion in industries and water odour problems in rural water supplies . Underground structures and systems in contact with natural water or water containing organic matter are most susceptible to bacterial attack.The types of metal-degrading bacteria , their characteristics and the conditions for growth have been reviewed extensively in the literature(1,2,3). There are several often encountered groups of bacteria which, through their metabolic processes, may lead to the degradation of metals. A large variety of bacteria produce corrosive in organic or organic acids as waste, such as the well known formation of sulphuric ac id by aerobic sulphur oxidizers . Anaerobic sulphate reducers produce hydrogen sulphide which is corrosive and has an obnoxious smell, slime-forming bacteria from slime which shelters sulphate reducers and iron bacteria oxidize ferrous to ferric ion which precipitates as hydrated oxides creating oxygen concentration cells . The following are bacterial problems encountered in Ontario Hydro. Although the number of recognized cases has been few, they show the diversity of location and environment where bacterial problems could arise. These include ground rod corrosion at transformer stations, corrosion of bare steel in a water intake structure, corrosion of steel in a nuclear generation station vacuum building and an odour problem in residential hot water tanks. In addition, possible bacterial- enhanced corrosion in containers for future disposal of nuclear fuel wastes are also discussed."

Jan 1, 1984

By Lawrence Devon Smith

The Business Case for Sustainable Development ?What are SD & TBL? ?Investment Funds & Fund Managers ?Banks and Risk Aversion ?The Dilemma of Juniors ?Meet Your New Partners ?The Cost of Problems ?The Cost of Delays Sustainable Development ?Humanity has the ability to make development sustainable -to ensure that it meets the needs of the present without compromising the ability of future generations to meet their own needs.? Our Common Future BrundtlandCommission, 1987

May 1, 2003

By Kim H. Shikaze, John R. Hawley

"Even though acid mine drainage is an old problem, particularly in coal mining areas, its appearance in the form of a major environmental hazard in the hardrock mining districts of Ontario was unexpected. The yellow and amber coloured wastes that characterize an acid mine drainage situation were first noted by the Ontario Water Resources Commission in the uranium mining Elliot Lake district. Problems of a similar nature were also noted in the copper-lead-zinc camp at Manitouwadge, the nickel camp at Sudbury and at numerous isolated base metal properties, both in and out of the Province of Ontario.Without exception, when acid mine drainage type effluents were evident, the specific companies involved worked sulphide or sulphide-associated ores. Without exception, the ore bodies contained quantities of iron sulphide (in various mineralogical forms) and, without exception, the milling circuits serving these operations were such that the iron sulphides were rejected to the tailings areas as waste.Once in a tailings area and after a varying period of time, iron sulphides react to form water soluble salts which, when discharged in the effluents from the tailings area, can affect stream chemistry and stream ecology.It is not unusual that the minerals pyrite, marcasite and pyrrhotite (all iron sulphides) react to form a stable oxide under atmospheric conditions. The law of stability of rocks and minerals, for instance, states that rocks and minerals are stable only in the environment of their formation and, as the environment surrounding them changes, the rocks and minerals tend to change to other species which are relatively more nearly stable under the conditions of the new environment (a). Under atmospheric conditions, iron oxide exhibits a greater stability than iron sulphide."

Jan 1, 1971