Search Documents

By K. D. Eng, W. T. Tierney

"During the past century, the development of vehicular transportation has benefitted tremendously from the performance improvement in engines in a situation where low-cost, plentiful fuel supplies were the order of the day. Engine advances were enhanced by and also dictated fuel modification to better adapt the energy source to the power plant.In discussing the several aspects of the change in approach from ""an engine and its fuel to a fuel and its engine"", the authors touch on the following areas:1. Description of an engine concept that provides the needed flexibility in fuel appetite at good efficiency to cope with future requirement s.2. The constraints placed on liquid fuel resource energy utilization efficiency by special engine-required fuel properties and the fuel efficiency of the various engine types available.3. Future vehicle engine fuel sources. This review will put into perspective the problem associated with the net energy available from future fuel sources under extensive research and development at present.4. A brief review of test data to show that fuel-tolerant and fuel-efficient engines are viable and that, in a fuel-resource-limited future, they can be a ""light at the end of the tunnel.""The Texaco Controlled Combustion System (TCCS)The TCCS is a unique means for stratified charge operation of an internal combustion engine in such a manner as to eliminate the requirement for octane or cetane number specification for the fuel. Octane rating is an empirical engine test method that evaluates a gasoline's resistance to spontaneous ignition or ""knock."" Cetane is based on a different engine test, which determines a diesel fuel's ease of spontaneous ignition . High cetane number enhances cold starting and permits high-speed diesel engine operation. As one would expect, the fuels in current use cover a band when the two values, octane and cetane, are plotted against each other."

Jan 1, 1982

By M. Oliazadeh, A. Vazirizadeh

"The inclusion of small amounts of silicon, phosphorus and sulphur in iron ores or concentrates can have a profound effect on the steel making process and thus on the final iron and steel products. In nature however, it is inevitable that iron deposits contain unwanted elements. Each element has its own distinct effect on the final steel product. The effect of high silicon is the formation of gray iron. Phosphorus mainly increases hardness and strength, lowers solidus temperature and increases fluidity and cold shortness. Finally sulphur contamination causes cracks in the iron texture when smelting and forms white iron when casting. Overall, the acceptable level of phosphorus, sulphur and silica in the iron concentrate should be less than 0.04%, 0.15 % and 1.5 % respectively.Scarcity of high grade iron ores necessitates using lower grade ores with higher amounts of impurities. The purpose of iron concentrators is to increase iron grades to an appropriate level suitable for steel making as well as removing impurities. Although many impurities can be traced in the ore, the most predominant impurities are limited to one or two elements. In this paper the beneficiation methods for removing SiO2, P and S are presented, including flotation, and the parameters that need to be considered in the design of beneficiation plants are discussed. Finally industrial cases are discussed along with their metallurgical performance.INTRODUCTIONIn metal sector, value of iron ores and concentrates is determined by iron percentage as well ascontent of:• Useful elements (Mn, Ni, Cr, V, Ti): natural alloying elements in steel• Deleterious impurities (S, P, As, Zn, Pb, K, Na): impair metal properties or complicate operational process in blast furnace• Fluxing components (Si, Ca, Mg,, Al)Sulphur and copper result in red-short, phosphorus is the cause of cold brittleness and arsenic and copper decrease welding characteristics. Sulphur should not exceed 0.15 in commercial ore. Acceptable sulphur content in ores and concentrates for producing sinter and pellets is 0.6%max, as sintering and heat hardening of pellets remove sulphur 60-90%. Phosphorous content in ores, sinter and pellets is limited to 0.07%-0.15%. 0.00.1% As max, 0.1-0.2% Zn max and up to 0.2% Cu are allowed in iron-ore part of the blast furnace burden for the production of standard conversion pig iron. Slag-forming components are divided into basic oxides (Ca, Mg) and acidic (Si, Al). Higher ratios of basic to acidic oxides are preferred since this reduces raw fluxing material."

Jan 1, 2016

By Phillip J. Mackey, Susumu Okabe

Copper mining and smelting has been carried out in Japan for over 13 centuries and in fact stretching back into antiquity. In 1889, the first electrolytic copper refinery in Japan based on Elkington’s principles was started by Furukawa Mining at Honjyo in downtown Tokyo based on the multiple or parallel system. Within two decades, a number of other copper refineries had begun operation. Interestingly, but perhaps not surprising given Japan’s long history of copper production, this first refinery in Japan commenced just ten years after the first refinery in the USA (1879), and not long after the first plants in Europe. By 1935, as a result of growth in copper demand, there were six domestic copper electro-refineries in Japan with an installed capacity of 97,800 tonnes/a, while actual production was 71,200 tonnes/a. Since about 1932, the majority of these plants were based on the more common parallel or multiple system. In 1946, just after World War II, domestic production capacity had dropped considerably to 29,000 tonnes/a, however with reconstruction, capacity and production expanded rapidly, with production reaching 81,000 tonnes/a in 1955, 187,000 tonnes/a in 1960 and 307,000 tonnes/a in 1965. The introduction of the first refinery and the early ones that followed and subsequent developments are discussed in this paper. The major technical achievements during the high growth period from 1945 to 1963 included: the use of fire- refined anodes; the introduction of newly-developed rectifiers; the introduction of lead-lined or vinyl-lined concrete cells; improvements in the electrolyte heating system; application of improved anti-corrosion materials and the introduction of heat-insulating surface coverings. In 2018, Japan’s refined copper production totaled 1,595,000 tonnes of copper, with Japan ranking third in the world after China and Chile. INTRODUCTION In 2018, Japan’s refined copper production totalled 1,595,000 tonnes of copper and Japan ranked third in the world for refined copper after China and Chile (Wood Mackenzie, 2019). There are now eight copper refineries in Japan which provide Japan’s production of refined copper. These plants are listed in Table 1 (Wood Mackenzie, 2019), also showing the production trend since 2013; in general, production over this period has been relatively steady. The Toyo plant is now the 7th largest copper refinery in the world after several large plants as rated by capacity in China, Russia and India (ICSG, 2019).

Jan 1, 2019

By Egon Berger

"In recent years the trend in underground metal mining has been toward ever increasing blasts (often in excess of 100 000 tonnes per blast). The Canadian mining industry has been in the forefront of these developments (VRM, LBHand cable bolting to stabilize the surrounding rock /avoid dilution).In order to move these large tonnages, efficient loading systems have to be developed. This paper shows the technical and economic implications of various loading scenarios based on a predefined (however typical) stoping layout by:1 . discontinuous loading using scoop trams;2. discontinuous loading using scoop trams in combination with low profile dump trucks;3. continuous loading (based on loading performance/operating costs of the AL-60) in combination with low profile dumptrucks.The cost advantages of production concentration (loading large tonnages from one drawpoint}, made possible by continuous loading as opposed to sea tiered mining (small tonnages), using discontinuous loading in tunnelling will be presented, based on actual results obtained in a decline development project using the A L-60 continuous loader. At as pacing oj150m between turning bays, it was found that continuous loading was out performing discontinuous loading in approximately80% of the overall decline development.Fuel consumption and total cycle times are compared, and a cost assessment is presented.INTRODUCTIONThe subject of this paper deals with the introduction of continuous loading in underground metal mining and single heading tunnelingContinous mining has been widely introduced both in underground and surface coal mining. Mechanized longwall mining, utilizing moveable shield supports in combination with double drum- shearers, has resulted in a tremendous increase of coal production per working face.This has led to very concentrated mining operations. In a typical German coal mine two mechanized longwalls nowadays would produce the same amount of coal as 12 to 15 longwalls in the 1950s. One longwall in a South African coal mine has recently set a world record with 120 000 tonnes of coal in a single month.In underground metal mines-often due to the irregular nature of the ore body and the mining methods used-mining is far less concent rated. Ore is often produced from a large number of stopes and production sections. Sometimes, a substantial amount of ore may be obtained from development in the orebody (40070 at a German base metal mine)."

Jan 1, 1989

By J. Petit

"In July 2004 workers at the ABI Smelter in Bécancour (Quebec, Canada) went on strike. Contingency plan were ready to face the situation and plan was done to operate one potline out of three. Two lines were stopped; keeping in mind the restart on cold metal after the strike was over. The subject to be presented and shared includes a summary of work organization including training, schedule of restart, pot cleaning, pot preparation, crash start method, follow up after crash start, safety and environment. This major project has been a very big challenge. It shows that people involvement is a must and the key success. It is then true to say : ""People who believe in success will work and act in order to get there"" and ""People who don't believe in success will act in such a way to fail"" Then both will prove they were right to think their own way ! Sharing such experience can be interesting because it's a true story and people like true stories."

Jan 1, 2006

By Adam J. Szladow

"INTRODUCTIONThe low calorific value and the high moisture and ash contents of run-of-mine (r.o.rn.) lignite limits the utilization of Saskatchewan lignites to thermal power plants in Saskatchewan, Manitoba and western Ontario. On the other hand, the low sulphur content and the low mining cost make lignites potentially attractive for new coal markets, if suitable processes can be found for upgrading. Economic upgrading to a higher quality fuel would make lignites more acceptable for industrial and utility boilers.This paper presents a summary of the process engineering evaluation of coal upgrading technologies conducted in support of a study of selected lignite upgrading processes. The summary presents the relative advantages and offers specific comments on the application of coal upgrading technologies for lignites. ResourcesLignite comprises the largest fossil fuel energy deposits in Saskatchewan. The total resources of immediate and future interest exceed 27 billion tonnes. The measured and indicated lignite resources of immediate interest are large enough to last for over 200 years at the current production rate of about 10 million tonnes per year (Table 1).Saskatchewan lignitedeposits are present in three different geologic formations: (I) the Ravenscrag Formation of Paleocene Age in southern Saskatchewan; (2) the Swan River Formation of Lower Cretaceous Age in central north Saskatchewan; and (3) the Judith River Formation of Upper Cretaceous Age in central west Saskatchewan. The deposits in the Swan River and Judith River Formation are not currently of economic interest.The Ravenscrag deposits are confmed to four lignite basins, namely: the Estevan, the Willow Bunch, the Wood Mountain and the Cypress basin (Fig. 1). The estimated resources of immediate interest in the four basins are over 7 billion tonnes (Table I). These resources include lignite seams at least 1.5 m thick, at depths of less than 45 m.The average quality of lignite varies relatively little between the four basins considering the distance between deposits (Table 2). There is, however, a progressive increase in moisture and ash content, and a decrease in calorific value and carbon content as one moves westward from the Estevan to Wood Mountain and Cypress basins. The Estevan area deposits are of higher rank despite the fact that they are stratigraphically younger than the Willow Bunch deposits (Cameron and Marconi, 1979).In upgrading lignite to a higher quality fuel, it is important to know not only the average proximate and ultimate analysis (Table 2) but also other lignite characteristics influencing the product quality . For example, Figure 2 shows the effect of lignite HIC ratio on the product equilibrium moisture for hydrothermal treatment of lignite. It is apparent that lignites with a higher HIC ratio, or high liptinite content yield much better quality product for the same hydrotreatment conditions. Other examples of lignite characteristics which are important in upgrading include distribution of sulphur forms and mineral matter, maceral composition and degree of surface oxidation."

Jan 1, 1989

"In the first half of 1990, Cambior earned $1104 million, or $0.37 per share, on revenues of$66.4 million. The company's strong cash position, attained late in 1989 and in the beginning of1990 through the exercise of warrants, put working capital at $83.8 million as of June 30, 1990. Long-term debt was reduced by over $10 million during the weak gold market, leaving the company with a debt to equity ratio of only 0.03. Production for the six first months of 1990 was 107 720 oz. Au, an increaseof24% over the corresponding period in 1989.Financial Profile/Results and Corporate Financial StrategiesTotal revenue for the 1989 fiscal year was $116,883,000 compared to $109,848,000 for 1988. The 1989 results achieved despite a lower average gold price, resulted from a higher level of commercial gold production and a 115% increase in investment income over 1988. Investment income rose to $3,568,000 in 1989 due to higher levels of cash assets.Cambior's mine operating costs increased 19% to $68,561,000 in 1989 from $57,472,000 in 1988. This increase resulted from rising operating costs at the Doyon Mine ($250/oz to $274/oz) due to the shift from open pit to underground operations, as well as from the start -up of three new mines with relatively higher costs. These costs have reached a stable level that should be maintained for the next few years.In 1989, net exploration expenses were $6,838,000, down 31070 from 1988, partially due to the Canadian tax reforms introduced since 1987. Depreciation and depletion grew by $1,432,000 in 1989, reflecting a higher volume of commercial production from the Pierre Beauchemin, Lucien C. Beliveau and Chimo mines.Net earnings for 1989 amounted to $17,661,000 or $0.73 per share compared to $17,438,000 or $0.74 per share in 1988.Cambior has an exceptionally liquid and strong balance sheet. As at December 31, 1989, net working capital stood at $85.6 million, with a total assets base of $338.6 million. With a long-term debt (including gold loans) of $21.5 million and shareholders' equity of $277.2 million, Cambior has a debt to equity ratio of 8%. All but about $100,000 of long-term debt is in the form of gold loans.The total market value for Cambior's stock as at September 10, 1990, stands at $420million, based on recent stock market prices. Cambior's stock and warrants are traded on the Montreal and Toronto Stock Exchange."

Jan 1, 1990

By H. A. Baxter

THE Eustis concentrator is located about nine miles southwest of Sherbrooke, on the main line of the Quebec Central railway. The concentrator is served by a side track parallel to the main line, and all supplies for both the mine and mill are delivered at the mill yards. The concentrator treats 250 tons of copper-iron ore daily by preferential flotation, whereby, first, the copper sulphides are floated and the iron pyrite is depressed, and, second, the iron pyrite is reactivated and floated, resulting in an iron pyrite concentrate and tailing, the latter going to waste. During 1934, 71,709 tons of ore were treated, averaging 3.712 per cent copper and 32.1 percent iron, with a small amount of silver and a trace of gold. The recovery was 93.77 percent of the copper, and 70.43 percent of the iron as iron concentrate. The copper concentrate produced averaged 25.623 percent copper and the iron-pyrite concentrate averaged 42.13 percent iron and 49.173 percent sulphur. HISTORY The first mill at the Eustis mine was built in 1904 (1). For a few years previous to this rime, some jigs had been operated to concentrate the fines from the mine, the coarse ore being hand-sorted. Both the fines and sorted lump ore were shipped to acid plants. The building of the mill was based on test work carried out by Professor Robert H. Richards at the Massachusetts Institute of Technology. The method of concentration consisted in careful classification in a Richards classifier, which made six different sized products. These products went to Wilfley tables, where a concentrate, middling, and tailing were made. The middling was returned to the rolls. Crushing was done by a jaw crusher and two sets of rolls, resulting in a screen size of about five-mesh.

Jan 1, 1936

By X. T. Zeng, X. Z. Ding, W. R. Chen, L. R. Zhao

The effect of deposition defects in metal nitride coatings on erosion behavior is presented. AlCrN, AlTiSiN, TiSiN and TiSiN:MoS2 coatings were fabricated by reactive cathodic arc evaporation and unbalanced magnetron sputtering processes. The microstructure and mechanical properties of the coatings were characterized by X-ray diffraction, scanning electron microscopy and nanoindentation, and the erosion property was assessed by solid particle impingement testing. The erosion characteristics on the coating surface and cross section were analyzed and correlated to the defects, which played an important role by promoting formation of erosion pits.

Jan 1, 2006

By Peter A. Bevan

"In massive and semi-massive deposits, it is essential to take samples continuously for specific gravity determination as well as for assays of the various metals of interest. Failure to use specific gravity in mixed deposits of high density contrast will result in incorrect determinations of the average grade.Graphs and linear equations of specific gravity against the grade of one metal are not considered accurate enough in a multi-mineral deposit, but appear to be very satisfactory in a theoretical one-sulphide/gangue mix. Specific gravities based on base-metal values only in massive sulphide deposits will result in underestimating the effect of low grade areas on the average grade and also cause a reduction in the calculated tonnage.IntroductionBy definition, a base-metal assay is the percentage of metal by weight contained in a sample, whether it be a soil or silt sample, a grab, chip or channel sample, or a section of diamond drill core.In those cases where there is a series of contiguous samples, say in diamond-drill core, the average grade may be required of the various assays that are above a desired or required cutoff grade.Internal low grade or waste can be included if the assays one side or the other are used to ""carry"" the lower grade material and the resulting average grade is above the cut-off grade. To determine the average grade, the individual assays are ""weighted"" by multiplying these values by their respective lengths, adding up the cumulative assay times length and dividing by the total length. This method is essentially a weighting by volume, because the core diameter is constant and is common to all the samples being considered for estimating the average grade . If some of the core samples have much higher specific gravities than others, and the specific gravities are not used in the weighting process, the resultant average grade will be over-estimated or underestimated, depending on the grade of the heavier sections. When core assays of approximately the same specific gravity or weight are averaged by length, the error in the weighted estimation of the average grade is negligible."

Jan 1, 1993

By S. Feinstein, I. Reznik, Y. H. Hatzor, O. Shitrit, Y. O. Rosenberg, H. J. Vinegar, S. Nguyen

"We report the effects of porosity and total organic carbon (TOC) content on the mechanical behavior of organic-rich chalks, based on laboratory measurements. The organic-rich chalks are from the Senonian Ghareb and Mishash formations. This deposit is an immature oil-prone source rock, about 300 meters thick, situated at shallow depths (several hundreds of meters) in the Shefela basin in central Israel. The study is based on core data collected from the Zoharim borehole.Three main phases comprise the bulk volume of this rock: 1) carbonate mineralogical phase (predominantly calcite); 2) pores (mostly saturated with brine); and 3) solid organic phase (type IIS kerogen). The mechanical effects of porosity (23-45%) and TOC (4-19%) are evaluated based on bulk incompressibilities vs. volumetric fractions analysis. Volumetric fractions of mineralogical and organic phases were obtained by porosity, density and TOC measurements. Saturated rock bulk moduli were measured through ultrasonic velocity measurements. Saturated rock bulk moduli correlate best with the sum of kerogen and pore volume fractions, rather than each of them separately. The volumetric fractions were also used to define the range of bulk modulus of the organic-rich chalk, using the Hashin-Shtrikman upper and lower bounds. Based on Marion's Bounding Average Method (BAM), the normalized stiffness factor of the chalk averaged at w=0.197, indicating a soft pore geometry. Using the average normalized stiffness factor, the BAM predictions showed excellent match with the saturated rock bulk modulus and the sum of kerogen and pore volume fractions. Based on our findings, it is inferred that kerogen grains do not support the solid skeleton but are distributed between the minerals grains. We also propose here a straightforward approach for calculating the Hashin-Shtrikman bounds, based on TOC and porosity measurements. The mechanical effects of porosity and TOC indicated here are very important for the understanding of the influence of immature kerogen presence in highly porous chalks, as the Ghareb and Mishash formations."

Jan 1, 2015

By S. N. Aliferova, E. I. Afonina, S. N. Titkov, A. Ju. Bondareva, N. N. Panteleeva

"Potash ore is mainly processed using the method of cationic flotation. Potash ore deposits of the CIS, namely: at Upper Kama river, Gremyachinsk (Russia), Starobin (Belarus), Tubegatan (Uzbekistan) are characterized by relatively low KCl impregnation (1.0 – 1.5 mm) and contain up to 10% of waterinsoluble impurities (WII). Water-insoluble impurities are presented by aluminosilicate, silicate, carbonate (calcite, dolomite) minerals and anhydrite. In the process of milling the ore to a flotation size there are released and dispersed the insolubles impurities actively sorbing the cationic collector, i.e. aliphatic amines C16 – C22. In this regard there is carried out a preliminary desliming of the ore.Currently grinding the ore to a flotation size (1.5 mm or less) is carried out in rod mills along with forming of a large number of fine-grained ore fractions having the size under 0.25 mm, which results in the increased KCl losses with halite slime waste and reduction in the quality of finished product. There has been developed the technique for processing of potash ores with a high content of water-insoluble impurities (10 – 12%) containing, in different ratios, silicates, carbonates and anhydrite. The technology involves the use of the ore dry grinding to the flotation size and subsequent reagent activation of the processes for sludge removal and sylvite flotation.INTRODUCTIONCurrently there are being developed the potash ore deposits in the CIS countries, namely: at Upper Kama river and Gremyachinsk deposits (Russian Federation), Starobin deposit (Republic of Belarus) and Tubegatan deposit (Uzbekistan). Potash ores are a mixture of sylvite and halite and contain water-insoluble impurities of silicates, carbonates and anhydrite. The content of water-insoluble impurities (WII) reaches up to 10%, disseminated (impregnated) sylvite does not exceed 1.5 mm and in connection with that the ore is crushed to a particle size under 1.5 mm. Ore grinding is performed by wet process in rod mills with producing a significant amount of fine-grained mineral fractions and sludge, which are actively sorbing a cationic collector, i. e. primary aliphatic amines C16 - C22. The ground ore is deslimed and the slime product is directed to a sludge depot (pits)."

Jan 1, 2016

By W. Curlook

"A review is presented of a growing number of imperatives, some self-imposed, some imposed by society, which the mining and metals industry faces in carrying out its business. These imperatives bear on all activities from the exploration phase, through engineering, design, plant construction and operation, to decommissioning.IntroductionThe mining and metals industry must learn to cope with, i.e. manage, a growing number of imperatives. Some of these, such as the need for responsible stewardship of natural resources, the requirement to respect laws and regulations, the need to provide for safe and healthy workplaces, and the need to provide appropriate returns to investors of capital , have been with the industry for a long time (fable I). But the industry now faces additional imperatives that are growing in number and in importance (fable 2):• There is the growing concern about the impact of operations, not only on the workplace environment and the external environment, but also on the need to monitor not only the chemical concentrations in various effluents but to also monitor the effects of such emissions on the environment; i.e. there is a growing concern about the ""net"" consequences of operations.• There is the need for on-going improvement in productivity and safety to compete and survive in a global economy. The global business environment has become paramount.• There is the imperative to failsafe all designs, equipment and operational procedures, and having done that to provide for containment of unavoidable spills, and to have ready and in place systems for emergency response.• There is the need, indeed the imperative, to involve all employees in various quality improvement programs.• There is the imperative to face up to ""virtual elimination/zero emissions""; and• One must have waste management plans in place to cope with the need to reduce, reuse, and recycle; and• There is the need for decommissioning plans for all operations, for the restoration of business habitats to their original states (or better). Indeed, one must engage in the decommissioning exercise from day one, i.e. right from the time of design and commissioning."

Jan 1, 1992

By Robert B. Parsons

"A joint federal/provincial/industry subcommittee of the Intergovernmental Working Group on the Mineral Industry (IOWG) has published an informative and readable report on taxation matters concerning Canada's mining industry. The report, which was presented to the federal and provincial mines ministers in September 1986, identifies and discusses key tax issues relating to this industry. The report is mandatory reading for anybody with an interest in mineral exploration or production in Canada.IntroductionIn 1986, Canada's federal and provincial mines ministers were presented with an important report concerning the taxation of this country's mining industry. This document is important for a number of reasons, two of the reasons being: first, the report contains an objective analysis of the key mineral taxation issues of the day; and, second, the report is the product of a cooperative exercise involving representatives of various facets of the industry and government. The report should be regarded as compulsory reading for anybody who has an interest in fiscal matters affecting mineral exploration and production.The ""Report on Fiscal Proposals"" was prepared by a subcommittee of the Intergovernmental Working Group on the Mineral Industry (IOWO). IOWO is a group of senior federal, provincial, and territorial government officials concerned with the analysis of mineral policy issues in Canada."

Jan 1, 1986

M INE production requires the coordination of the talents of men and the use of equipment. Mine operators maintain a continual surveillance of equipment, looking for improvements and modifications that will benefit them. Few give similar attention to the advances made in the education of mining engineers since they themselves graduated. That is not surprising. Education lacks the advertising budget available to manufacturers. A modification to improve a mechanical contrivance is advertised, and an advertiser's press releases get attention by publishers. The whole program for mining engineering education could be revolutionized and no one, except a few professors, would know about it. The Canadian Institute of Mining and Metallurgy's newly established General Commit-tee on Education can improve that situation. Nine groups of engineers in Canadian universities are trying to give undergraduates an education that will make them useful to the mineral industry as mining engineers. The tabulation offered here (Table I) is an analysis of the distribution of the undergraduate-teacher contact time.

Jan 1, 1963

By S. L. Gula

"Effective and timely communication during routine operations, and especially during emergency situations, is no easy task in any underground mine. At Cominco Fertilizers, Potash Operations, where 150people are employed underground to produce 3.1 million tonnes of potash per annum at a depth of 1100 m (3600ft), this is no exception. The over-all mine workings underlie an area of approximately 20 km 2 with average travel time to the active mining areas being approximately 30 to 40 minutes by light vehicle, and significantly longer than this for heavy equipment.In a mine of this size, the deployment and management of personnel and materials on a day-to-day basis, and during mine emergencies, is an important exercise. The Personal Emergency Device (PED) system has provided the Potash Division a means to achieve improvements in this area and reduce the communications bottleneck.The MineAt Cominco Fertilizers Potash Operations, approximately 30 km southwest of Saskatoon, the orebody is the same horizon being mined by other potash producers in the Saskatoon area and extends over 300 km in an east-west direction, and approximately 150 km in a north-south direction. Mining operations are carried out with approximately 150 employees operating on a continuous-shift basis, seven days a week.Mining is presently being done from Block 6 which takes the mine to its northernmost boundary and contains reserves of approximately 50 million tonnes. Production is from one level by five twin rotor continuous mining machines, each capable of cutting a face up to 5.5 m wide and 3.3 m high . All ore is transported to the shaft via approximately 20 km of conveyor where it is removed to surface by two 24 tonne skips.After the ore is conveyed to the mill for processing, the finished product is shipped by rail car or trucks to other parts of Canada, the United States or through Vancouver to other parts of the world."

Jan 1, 1993

By K. Hashiba, Y. Z. Liang, K. Fukui, M. Koizumi

"Efficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Development and modification of the rock drills based on test data are timeconsuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved. The objective of our research project is to construct a new realistic numerical model of continuous percussive drilling, which is based on the previous Okubo-Nishimatsu’s model. In this study, the parts of the previous model involved in stress wave propagation and attenuation were modified. The two models were prepared for HD712 hydraulic rock drill mounted on crawler drills and HD210 hydraulic rock drill mounted on drilling jumbos. Stress wave propagation was computed with the discretized one-dimensional wave equation. The calculated results were compared to the stress waves measured on a rod during percussive drilling. In both models for HD712 and HD210, the measured stress waves can be reproduced with the one-dimensional model of the same acoustic impedance as the actual piston, shank rod and rod combined with the CI+spring model as a rod joint. The calculated results indicate that the spring constant in the model of a rod joint needs to be set appropriately depending on drilling conditions. INTRODUCTIONEfficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Components related to the percussive drilling are a drill body, a piston, a shank rod, rods, rod joints, a bit and rock. The piston in the drill body is reciprocated by hydraulic pressure and collides with the shank rod a few thousand times per minute. Stress waves generated by the collision propagate and attenuate in the rods and rod joints, and then reach the bit. The bit penetrates and crushes rock. During percussive drilling, the components mutually affect each other and self-induced oscillation occurs. The number of blows and the rate of penetration are determined by the practical drilling conditions such as hydraulic pressure, thrust force, number of rods and mechanical properties of rock. Development and modification of the rock drills based on test data are time-consuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved."

Jan 1, 2015

By V. V. Zubkov

The systems of geophysical monitoring have been already put into operation at coal mines and ore mines. Since at present it is rather difficult to conduct mine experiments; it is necessary to start a new step in joining of geomechanics and seismic. The linking geomechanical and geophysical monitoring at coal mines and ore mines today became possible due to progress in development of numerical methods of modeling of stress state and technology for processing of seismic information. This paper describes one potential step in linking geomechanical and seismic monitoring at coal mines and ore mines.

Aug 1, 2013

By Nicola Robjohns, Kenneth A. Grace, Jane Spooner

"The important volume end use sectors for the rare earth elements and yttrium continue to be in steelmaking, petroleum cracking catalysts and glass polishing. The market sectors which may provide future high volume demand, to replace the older sectors where demand has declined over the past decade, include magnets, automobile catalysts, ceramics and superconductors. Increases in production capacity in all major rare earth producing countries are expected to restrain large price increases for high purity rare earth oxides over the short term. A sharp increase in demand for yttrium in advanced ceramics and superconductors would lead to a shortage in separation capacity, however, and to a corresponding rise in prices for separated rare earths.IntroductionWhile visiting the Geology Department of the University of Toronto in 1981, Professor Lu from the Institute of Geochemistry of Academia Sinica at Gweiyang in China introduced one of his seminars with the observation that in China, rare earths are not rare at all.Indeed, while being rare in terms of abundance as measured by, say, the Clarke scale, the rare earth elements, like many other low abundance elements, are subject to geological, geochemical and mineralogical concentration.The rare earth elements comprise the fifteen inner transition elements of Group IIIB, Period 6, of the periodic table, from lanthanum to lutetium (the lanthanides), as set out in Table 1. The rare earths constitute a distinct group as they have extremely similar chemical characteristics due to the uniformity of their outer electron shells. The element yttrium is usually, by convention, included in the rare earth group as it occurs with the rare earths in nature and has properties very similar to them.The rare earths are divided into two subgroups, the ""light"" rare earths, made up of the first seven elements of the series, lanthanum to europium, and the ""heavy"" rare earths, comprising the remaining eight elements, gadolinium to lutetium, plus yttrium. These two subgroups are also referred to as the cerium subgroup and the yttrium subgroup, respectively. The subdivision is based on differences in the atomic radii resulting in somewhat different properties for the two subgroups."

Jan 1, 1991

By Robert B. Parsons

"Considering the traumatic events of Canadian mining taxation of the 1970s, one wonders at the sanity of anybody who tries to predict what the 1980s might hold for the tax structure of the mining industry. Yet, the author agreed to tackle this task when called upon to do so at the annual meeting of the Quebec Metal Mining Association in June. The text of this ""daring"" speech follows.IntroductionI have been asked to play the part of the oracle at Delphi, and to predict what the 1980s might hold for the Canadian mining industry in terms of taxation. To appreciate the challenge of this difficult assignment, try to imagine someone in my position back in 1972 attempting to forecast the balance of the 1970s. I daresay that ten years ago nobody could possibly have conceived of the devastating and casualty-ridden rollercoaster ride that mining taxation actually took in the 70s. Nevertheless, I shall examine the entrails and try to shed some light on what might happen during the balance of this decade as far as mineral taxation is concerned.If one were to retreat deep into history, one would find that taxation generally served one purpose-namely, to raise revenues for the government. More recently, an important second function has emerged: taxation is increasingly being used as a fiscal tool-a tool intended to mould and shape future events in order to accomplish certain economic, social and political objectives. It is these two main forces-the need (or desire) for revenues and the perceived convenience of using taxation as a fiscal tool-which will continue to shape the tax structure of the future.In our assessment of where taxation of the mining industry may be headed, we should be able to learn something by looking at where we have been."

Jan 1, 1982