Search Documents

By N. N. Rulyov

"Starting from fundamental principles of colloid-hydrodynamic theory of disperse systems we have shown that application of strongly non-uniform hydrodynamic fields allows to achieve not only faster rates of flocculation of suspension, but also supports significant improvements in the quality of clarified water and separation characteristics of solid phase. Specifically, it has been experimentally proven that the new treatment method based on these principles (then termed as ""ultra-flocculation"") allows:•,Increase the output of thickeners and pressure filters by 1,5-1,7 times;•,Decrease solids fall through into the filtrate in the process of vacuum filtration by 2¬3,5 times;•,Improve the rate of purification of water phase in the upright thickener by 1,5-1,9 times;•,Decrease flocculant consumption by 1,5-3 times;•,Increase the effective operational life time of cloth filters by 3-4 times;•,Ensure sustainable operation of separation equipment, i.e. decrease the sensitivity of process to variation in suspension concentration, as well as to variations of suspension composition and dispersion characteristics;•,Apply flocculant solutions of concentration 2-3 times higher, thus increasing the capacity of equipment used for solutions preparation."

Jan 1, 2004

By F. Mackay, S. A. B. da Fontoura

"The theoretical solution for a viscoelastic well was presented by Gnirk and Johnson in 1964. From this an exercise was executed to validate the numerical simulation of a cemented salt well. The exercise comprised the geomechanical behavior through time of a cemented salt well, this was achieved using a finite element commercial software. This simulation showed the accuracy of the theoretical solution for viscoelastic materials such as salt rock. The theoretical solution presented elastic and viscoelastic analytic equations for the tangential and radial stresses. The equations for the elastic material (casing and cement) and for the viscoelastic material (salt rock) are presented here: Where equations 1a & 1b are the radial and tangential stresses of the elastic material; equations 2a & 2b are the radial and tangential stresses of the viscoelastic material; and a, r and b are the geometrical parameters explained in Figure 1. These equations are function of Pb, a stress time dependent factor that comes from the Burgers model of viscoelasticity. This is well explained in Gnirk and Johnson (1964) and for the sake of simplicity is not disclosed here. Po is the stress at section A-A’ dependent of the depth h."

Jan 1, 2015

By L. Voisin, E. Díaz, V. Montenegro, W. Kracht

Grinding media is of great concern in the mining industry mainly because its consumption represents an important part of the costs during mineral processing and consequently, of the total mining business OPEX. In addition, grinding media consumption impacts directly on flotation performance through negative contamination by corrosion, affecting the pulp chemical potential, complicating the understanding and control of the process, as galvanic interactions between mineral species also occur. In addition, during the process there is also a physical consumption of the grinding media through erosion and impact. In both cases, mineralogy has an important role because pulp abrasion power, chemical reactivity, rheology, hardness and other variables depend on the minerals contained in the pulp and their interactions. In the present study, a geometallurgical and phenomenological model, which describes the grinding media consumption and its relationship with mineral hardness expressed by Bond Work Index, was obtained based on advanced mineral characterization techniques such as Hylogger3TM, X-ray diffraction, X-ray fluorescence and experimental grinding tests using a laboratory mill applied on Chilean copper pulps. The results obtained show that pH has an important effect on grinding media consumption, because corrosion varies with hydrogen ions availability. Also, mineral hardness depends on mineralogical composition, but textural analysis must be performed to have a better description of this property. Finally, minerals present in a sample define the grinding media consumption mechanism, because a sample with harder minerals and a greater value of Bond Work index is capable of protecting grinding media from impact wear, while a sample with lower hardness but with a big sulfide minerals content would be more aggressive with grinding media because corrosion is more important in this case. The geometallurgical model obtained is capable to relate the grinding time, mineral hardness, content of sulfide minerals and grinding pH to estimate the grinding media consumption.

Jan 1, 2017

By Abhilash

Uranium is conventionally extracted using a process that employs strong acid (H2SO4) and an oxidant (MnO2) as leaching agents. This method often creates environmental problems, requires large amounts of energy, and involves a complex operational plant. It is not, however, economically attractive to extract uranium from low-grade ores by chemical leaching. Because the content of U3O8 in the Indian ore is usually below 0.1% by weight, it is necessary to develop an alternative process to enable the efficient and economic recovery of uranium. Uranium ore from the Narwapahar mines, UCIL is a type of vein deposit found in India, which accounts for ~54% in India. The ore (0.047% U3O8), though of Singhbhum area, possess exceptionally different mineralogy due to presence of some refractory minerals and richness of apatite (5%) resulting in a maximum 78% recovery through conventional processing at UCIL, with a very high consumption of sulfuric acid and pyrolusite, besides possible loss of uranium as uranium phosphate. To avoid usage of environmentally non-benign oxidants, remediation of influence of phosphates, and improve the overall process output of uranium; an alternate extraction technology using microbial isolate(s) is worthwhile exploring and the same is presented in the paper. The microbial isolate enriched with Acidithiobacillus ferrooxidans grown from source mine water was employed for bio-leaching of uranium while varying pH, pulp density (PD), particle size, etc. On varying pH at 35oC using 20%(w/v) PD and <75µm particle size, 83.5% and 78% uranium bio-recovery were observed at 1.7 and 2.0 pH in 40 days against maximum recovery of 46% and 41% metal in control experiments respectively. Whereas, it was observed that grinding of ore to finer size actually helped dissolution of uranium. Finer size particles (<45µm) gave a maximum biorecovery of 93% in 40days at 10%(w/v) PD, 1.7 pH and 35oC. The bio-recovery of uranium fell down from 93% to 82.73% and 60% on increasing the pulp density from 10% to 20% and 30% respectively for particles of <45µm size. The higher uranium dissolution during bioleaching at 1.7pH can be correlated with increase in redox potential from 433 mV to 664mV in 40 days.

Aug 1, 2010

This paper describes basic parameters, such as surface forces and film elasticity, affecting the stability of foams (two-phase froths). We used the thin film pressure balance (TFPB) technique to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG). The results were compared with the foam stabilities measured experimentally and the film elasticities calculated using a new model developed by Wang and Yoon (2006). It was found that at low electrolyte (NaCI) concentrations foam stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother type and concentration. Further, the kinetics of film thinning was studied at a high electrolyte concentration. The results obtained in the present work showed that the major role of a frother is to decrease the hydrophobic force rather than to increase the film elasticity. This conclusion is drawn from the observation that at the typical frother (MIBC) concentrations employed in flotation, frother additions cause sharp decreases in hydrophobic force while causing relatively little changes in film elasticity.

Jan 1, 2006

By K. Buxmann

Climate change is a subject of growing concern. Based on the International Energy Agency, about 19% of man made greenhouse gas emissions globally are generated by the transport sector. This paper will focus on the environmental aspects of the light-weighting in transport and the resulting savings of fuel and electricity. Aluminium is an option for lightweight applications in transport, with very high benefits not only in the use stage, but also in the stage of vehicle recycling. Life cycle assessment is used to quantify the relative benefits of light-weighting specific components of cars, commercial road vehicles, buses, ships and trains. A vehicle consists of many components, which are produced by different processes and undergo different types of end-of-life operations. This document does not intend to compare a generic aluminium vehicle with a generic "heavy materials" vehicle. It rather tries to use a pragmatic approach based on specific examples of components where aluminium is used and can be used in the design of new vehicles, also taking into account future developments. The case studies in this paper are based on real cases where aluminium was used. For each component, sensitivity analyses are applied to see the impact of specific parameters such as the end-of-life recycling rate and the use stage driving distance. Significant greenhouse gas savings by the use of aluminium are demonstrated for cars and even higher ones for trucks, buses, trains and ships. In addition, the total potential benefits of light-weighting with aluminium are shown on the global level.

Jan 1, 2007

By G. F. Warning

"THE H. B. Mine is situated on the north side of Sheep Creek valley, about six miles southeast of Salmo, B.C. It is the most northerly producer along a belt containing a number of zinc-lead deposits, including the Jersey mine of Canadian Exploration Limited, 3 miles to the south, and the Reeves MacDonald mine, 12 miles to the southwest. The important zinc-lead producing area around Metaline Falls, Washington, lies 23 miles to the south. Two prospectors, Horton and Benson, located and staked the oxidized outcrops in 1.907. The property was named the H.B. after the two discoverers. Exploration by a number of operators failed to locate any sulphide orebodies until 1946, when Cominco began a geological study followed by surface drilling which was successful in locating extensive sulphide mineralization. A program of underground exploration revealed sufficient ore to war-rant mill construction. A 1 ,000-ton mill was completed by 1953, but due to low metal prices production was deferred until May, 1955. To September 1, 1959, 1,900,000 tons of zinc-lead ore have been milled; present milling rate is about 1,250 tons per day. Concentrates are trucked to the Trail Smelter, a distance of 35 miles."

Jan 1, 1960

By E. P. Evoy, A. W. Jolliffe

"The Uranium deposit of Gunnar Mines, Limited, is on the south shore of Crackingstone peninsula in the Beaverlodge area of northern Saskatchewan.The ore consists of disseminated pitchblende and uranophane in brecciated syenite, and forms a tubular or pipelike body, outcropping at the surface and plunging southward at about 45 degrees for a known length of1,400 feet (see Figure I). The upper portion is being removed by open-pit mining to a depth of 300 feet below adjacent Lake Athabasca. The remainder will require underground mining methods (see Figure 2).The property was staked in July, I 952, and the orebody was subsequently defined by about 70,000 feet of diamond drilling. A 1,250-ton mill was completed in 1955, and production commenced in September of that year with ore from the open-pit operation. The mill is presently being increased to 1,650 tons capacity, and a three-compartment vertical shaft is being sunk to 1,250 feet in preparation for underground mining.GeologyThe mine property is underlain by an assemblage of Precambrian metasediments known locally as paragneiss, granite-gneiss, and syenite. These lie on the southeast limb of a southwest-plunging anticline, strike about north 75 degrees east, and dip southward at about 45 degrees. Para- gneiss outcrops in the northwestern half of the claim group, and again on the islands south of St. Mary's Channel. The granite-gneiss lies conform-ably within the paragneiss and makes up the southeastern part of the property. The syenite forms an irregular, triangular-shaped mass within, and near the footwall of, the granite-gneiss band. Small lenticular bodies of mafic rocks are also present, the former being most prevalent in the paragneiss.The granite-gneiss is coarse to medium-grained, pink to grey, well foliated, and composed of feldspar (65 per cent), quartz (20 per cent), chlorite, and minor mica. The general concordance of its contacts with paragneiss and the absence of intrusive relationships along these, the presence of uniformly oriented inclusions of obviously sedimentary origin within the granite-gneiss, and the variation in colour and texture across the strike all strongly suggest that this member represents a granitized sedimentary rock."

Jan 1, 1949

By H. Karakul

Determination of P-wave velocity (Vp), which is closely related to intact rock, is a nondestructive, easy and less complicated procedure. Due to these advantages, there is an increasing trend to predict the geomechanical properties of rocks from Vp. In addition to mineral content, cementing material and porosity, degree of saturation (Sr) are also other factors influencing geomechanical properties of the intact rock. However, up to the present, in the studies on the prediction of geomechanical properties of rocks from Vp, the effect of Sr has not been investigated. By considering this issue, in this study, it was aimed to correlate strength properties (uniaxial compressive and tensile strengths) and Young’s modulus with Vp of various rock types under different degrees of saturation. In addition, geomechanical properties of rocks were estimated from theoretical P- and S-wave (Vs) velocities, which were calculated based on their mineralogical compositions. For this purpose, fourteen different rock types were collected from several parts of Turkey and a comprehensive laboratory testing program was conducted. In the statistical analyzes, a series of different prediction relationships were developed by using independent variables such as Vp, Sr and effective clay content (ECC). Simple regression analysis results indicated that although prediction of the geomechanical properties of rocks from Vp at different degrees of saturation was possible, the equations developed would yield some under- or over-predictions. On the other hand, the multivariate equations developed have very high prediction performances and are very useful tools to estimate the geomechanical properties from the measured Vp at any Sr value. In addition to mineralogy, the variation in geomechanical properties with increasing Sr is also associated with the combined effect of porosity and clay content, which is first described in this study by the term Effective Clay Content (ECC). It is also noted that strength properties of rocks at any Sr may also be estimated using the empirical relations based on the theoretical Vp and shear-wave velocity (Vs) values, which are calculated from their mineralogical compositions.

Jan 1, 2015

By A. Torkian

Process water from production of concentrates in Meydook copper sulfide mine is transferred to the 8.3 million m3 tailings dam and a water retention pond after initial thickening. Elevated concentrations of heavy metals, sulfate, and TDS and decrease in pH as well as seepage into the aquifers have been the concern of the regulatory agencies since the start of activities. In this paper the results of a 6-month monitoring program from 4 wells are presented. The wells were located approximately 1.5 km from downstream of tailing dam (0.4 km from water retention pond) as well as upstream background well (2.28 km from water retention pond and 1.27 km from tailings dam). The objective was to study possible effect of accumulated tailings on the groundwater resources. Water levels in sampled wells were on average between 20 and 40 m. Results showed high levels of lead (5 ppb), copper (0.17-0.46 ppm) and selenium (73.1- 29.1 ppb). High levels of selenium and lead were partly due to natural geological settings of the area with high levels present in unaffected soils in the vicinity including water wells of villages upstream of mining operations. High copper levels were attributed to both mining operations as well as deposition from particulate air deposition onto the soil and transport to ground water by rain.

Aug 1, 2013

By A. Sutherland Brown

"The Red Rose Mine is in the Rocher Deboule Range, 8 miles south of Hazelton. The mill camp (elevation 4,000 feet) is on Red Rose Creek, 11 miles by road from Skeena Crossing. The mine camp is one mile northeast and 1,600 feet above the mill camp on a spur of Red Rose Peak.The Red Rose mine was described in the Jubilee Volume, Structural Geology of Canadian Ore Deposits (Davis, pp. 129-131), but regional geology and mine development have progressed to a stage at which a more complete description is possible.The property was first located in 1912, and for the next 7 years was prospected actively for gold and copper on the southern extension of the Red Rose shear. Scheelite was first discovered in the vein in the northern part of the shear in 1923. The Consolidated Mining and Smelting Company of Canada, Limited optioned the property in 1939, and after a drilling program in 1940 the present mine development was initiated in the vein in the northern part of the shear. A 75-ton-per-day mill started operating early in 1942 and continued until 1943. The property was inactive until 195 l, when Western Tungsten Copper Mines Limited leased the property from The Consolidated Mining and Smelting Company of Canada, Limited. A mill, which later was enlarged to 140 tons per day, started operations at the end of 1951. The mine and mill were closed in December, 1954.The mine has twelve levels and sub1evels, and most of the workings are in the plane of the vein (see Figure 2a). The level interval is not constant, but between the lower four levels is 87 feet (100 feet in the plane of the vein). Access is provided by four adits; the 800 (elevation 5,659 feet), 600 (5,920 feet), 300 (6, 133 feet) and 200 levels (6,237 feet). The 600 level is the main haulage, and from it the ore is transported to the mill by aerial tram. From this level an inclined shaft extends in the vein to the lowest level (I, 100)."

Jan 1, 1949

By M. Maeda, H. Sasaki

"Precious metals such as platinum, palladium, and rhodium are commonly used for automotive catalyst converters. To recover these metals with lower environmental load and cost, exposure to zinc vapor was proposed as a pretreatment prior to acid leaching. Alloying with zinc is expected to enhance dissolution of precious metals and reduce the amount of toxic chemical agents required for the leaching. This study examined the effect of the alloying pretreatment using model catalysts. Catalysts were immersed in leaching solutions for a predefined time with or without zinc vapor pretreatment, and the amount of dissolved metals was then evaluated. INTRODUCTIONAutomotive catalysts account for large portions of the world consumption of platinum (Pt), palladium (Pd), and rhodium (Rh) (Butler, J., 2011). Because of their limited production and high prices, recovery of the precious metals from spent catalysts is obviously an important issue. A representative structure of an automotive catalytic converter can be described as a monolithic ceramic support with a honeycomb structure which is coated with porous oxides such as those of aluminum (Al2O3), cerium (CeO2), and zirconium (ZrO2) (Heck & Farrauto, 2001; Matsumoto & Shinjoh, 2007). Small particles of precious metals, originally several nanometers or less, adhere to the oxides.Typical recovery processes for precious metals from scraps are shown in Figure 1 (a)-(c) (Habashi, 1997; Yoo, 1998; Shibata & Okuda, 2002). Precious metals can be recovered by using non-ferrous smelters as Figure 1 (a) shows. Smelted along with metals such as copper (Cu), precious metals and ceramics in the scraps are absorbed into the metal phase and slag phase, respectively. Because the metals separate from Cu as anode slime in successive electro-refining, such a process can recover precious metals as co-products of Cu. However, in order to prevent negative effects on the principal process, a specialized procedure is needed. Figure 1 (b) is a specialized approach in which scraps are melted at elevated temperature with Cu called the Rose process. Here Cu works as a collector metal, and the absorbed precious metals are then concentrated by oxidation of Cu. Such a process can separate precious metals from ceramics constituting catalyst converters. Smelting at high temperature, however, requires extensive equipment as well as a high amount of energy. On the other hand, hydrometallurgical processes may be effective to separate precious metals from ceramics into an aqueous solution, because chemical agents can act on these metals selectively (Figure 1 (c)). Leaching of precious metals, however, requires strong acid and oxidizing agents because of their corrosion resistance; this makes liquid waste disposal and the large environmental load controversial. To solve the problem, a metal vapor pretreatment was proposed (Okabe, Yamamoto, Kayanuma, & Maeda, 2003a, 2003b; Kayanuma, Okabe, Mitsuda, & Maeda., 2004; Kayanuma, Okabe, & Maeda, 2004; Itoh, Kayanuma, Miyake, Kimura, & Maeda, 2005). A flow diagram of the process using zinc (Zn) vapor is shown by Fig. 1(d). Exposed to Zn vapor, precious metals are expected to form alloys which dissolve more easily than pure precious metals, thus reducing the use of chemical agents and environmental load involved with successive leaching. In previous research (Sasaki, Miyaki, & Maeda, 2010; Sasaki & Maeda, 2010, 2012), dissolutions of precious metal alloys formed by Zn vapor treatment were examined in hydrochloric acid (HCl) using an electrochemical method, and it was confirmed that these metals dissolved at higher rates from the alloys than from their pure states (Figure 2). In this study, the availability of the alloying pretreatment was demonstrated by testing on model catalysts in leaching solutions."

Jan 1, 2012

By S. S. Al-Thyabat, A. M. Ghrair

"Printed circuit board (PCB) is the main part of any electric or electronic device, providing mechanical support and electric connection for the board eclectic components such as capacitors, resistors, diodes etc. PCB consists of non-conductive substrate overlaid with one or more layers of copper sheets. They also contain appreciable amounts of base metals (copper, nickel, tine, and aluminum) and precious metals (gold, silver, and rare earth elements (REE)) which end up in the landfill at the PCB end-of-life.PCB recycling E-waste in general is a profitable business; many valuable raw materials, precious and base metals, can be extracted with high purity. Approximately, one metric tonne of PCBs may contain 80-1500 g of gold and 160–210 kg of copper. The precious metals recovered from PCBs occur at concentrations higher than commercially mined minerals. Also PCB recycling is very important to our environment since many heavy metals (e.g. lead) may be leached from the landfills to the underground reservoirs. In Jordan, however, the work conducted on E-waste and PCB recycling in particular is limited; currently most of the E-waste is either exported or dumped in the landfill.In this work, a combination of physical (magnetic separation), physicochemical (flotation), and chemical methods (leaching) were used to compare metals concentrations in leach liquors produced from a concentrates resulted from a combination of these methods. It was found the leach liquor of the magnetic fraction of the PCB coarse size gave the highest concentration of Fe, Al, and Ni while concentration of Cu was higher in leach liquor of nonmagnetic sink fraction. On the other hand, metals concentration almost similar for both sink and float of the fine size fractions, indicating even distribution of metals concentrations in the fine size fractions."

Jan 1, 2016

By F. Y. Hsiao, H. C. Kao

Underground excavation in hard rock is normally stable at shallow depth except for wedge failure. However, the excavation depth is rapidly increasing recently. In high overburden stress condition, the integrity of rock would be destroyed with degrading rock strength. Therefore, understanding both the peak and the post-peak strengths of hard rock are necessary to assess the tunnel stability at depths. The characteristic of the post-peak strength is seldom studied in Taiwan in the past. Various estimation methods for the post-peak strength degradation were briefly reviewed in the paper. Based on the Geological Strength Index (GSI) system is widely used in the determination of the rock mass strength, the quantitative residual GSI system was adopted to estimate the possible strength degradation for a hydraulic tunnel in Taiwan. The Mohr-Coulomb model (no strength degradation) and the post-peak strength degradation model (strain softening model) were used to simulate the excavation of the case tunnel at different depths. The analyses demonstrate that the tunnel is in stable condition at 600m of depth. And the effect of the postpeak strength degradation on tunnel deformation is progressively significant with increasing tunnel depth. Approximate 3-5 times of increase in crown settlement and horizontal convergence would occur when post-peak strength degradation are considered at 2400m of depth. Severe tunnel deformation may endanger the tunnel stability. Modeling results reveal that the post-peak strength degradation has a great effect on tunnel stability under high overburden stress condition, which should not neglect in deep tunnel design.

Jan 1, 2015

By Larry B. Smith

"Feasibility studies are the means by which mineral reserves are established prior to financing a project. However, guidelines are generally lacking for the content, data quality and accuracy of these studies. Regulators take a principle-based rather than prescriptive approach to the content of studies and look to the industry to define study content. Professional organizations, engineering firms and mining companies must eventually establish guidelines and best practices for this work. Most likely these will draw on standards or “stage gates” that have been developed by major mining houses and engineering firms. Engineering studies must: 1.,Define optimal mining and processing methods, production rates, infrastructure, product sales, environmental management and risk mitigation. 2.,Increase confidence in resources, reserves, production plans, processing performance, infrastructure design, environmental management, permitting, capital and operating costs, and financial performance to support financing. 3.,Provide engineering designs suitable for accurate cost estimates. 4.,Develop project execution plans with sufficient confidence that project delays and cost overruns will not occur. Conceptual (scoping, preliminary assessment) Establish the principal characteristics of the project from the geology, resources, metallurgy and development constraints. Assess different approaches to mining and processing. Identify project execution requirements. Test project viability with economic analyses. Recommend additional work to increase the confidence in geology, resources, metallurgical performance, infrastructure, operating and capital costs, environmental conditions and permitting to allow selection of the best development options."

Jan 1, 2003

By A. Sadough vanini A. Kami

In this paper, effects of different ageing treatments on the mechanical properties, microstructure and formability of 7075 aluminum alloy have been studied. Forming limit diagrams of the alloy have been obtained for four ageing conditions including T6, OA1, OA2 and O. For this purpose, combination of uniaxial tensile tests and the Erichsen cupping tests with different sizes and shapes of sheet specimens have been performed after each ageing treatment. The highest formability and the lowest formability have been observed at samples with O and T6 ageing treatments, respectively. Also, investigation of precipitated microstructures showed that the size of precipitation particles has a significant effect on the formability of the alloy. Formability improves with coarsening of precipitation particles.

Oct 1, 2011

By A. Rahmati

Geological and geo-statistical modeling of the ore deposits play a prominent role in resource and reserve estimation for geo-statistical evaluations. Sheytoor iron deposit is located in the Bafq iron ore district (Central Iran) and in the south-east of the Esfordi 1:100000 sheet. According to the geological data, limestones and dolomitic limestones are situated in the north and central parts of the area, on the other hand, iron ore outcrops are observable in the center, south-west and south-east of the studied area. Meanwhile this ore deposit represents a sulfide one. Based on the boreholes data, geological and geostatistical models of the high and low grade iron mineralization zones were generated by Rockworks v.15 software. The IDW method was selected and employed for processing the collected data and a good adaptation between the results was revealed. The distribution model of Fe concentration displayed a relatively high grade Fe in the center, south and south-east parts of the area. Furthermore, this model illustrated a relatively high grade S and P in some parts of the center, north and south-east of the area. The Fe concentration, in the high grade mineralization zone, was between 45 and 61.5%. In addition, in the low grade mineralization zone, it was between 3.64 and 57.64%. Moreover, in the intrusive granites, the Fe concentration was between 30 and 48.73%. Due to the significant amount of the sulfur in the deposit model, most of Fe-bearing minerals are pyrite, so it is recommended an evaluation on Cu-bearing minerals and their related elements in the area to get done. Additionally, there are too much Fe values in granitic zones which could be caused by possible measurement errors and the geological classification of the area. Therefore, it should be done more carefully.

Aug 1, 2013

By K. Ihara, R. Akiyoshi, Y. Takaki, S. Kang, H. Shishido

"Tensile tests and scanning electron microscopy-electron backscattered diffraction (SEM-EBSD) analysis were performed in an Al-Mg-Si alloy to clarify the effect of annealing and cold-rolling reduction on the texture formation. The hot-rolled specimens were cold-rolled with the reduction of 58-75%(CR1), followed by annealing at 773 K for 5 min(IA). The secondary cold-rolling(CR2)for the IA specimens with the reduction of 33–66%, followed by the solution heat treatment(ST), were performed. Focusing on the CR1 and CR2 specimens, the average r-values increased with higher primary and lower secondary cold-rolling reduction, respectively. This was considered to be due to the increase of r-values measured in the direction of 45 degree with respect to rolling direction, caused by the formation of the ß-fiber components (Brass {011}<211>, Copper {112}<111> and S {123}<634>) with high density. Based on the texture analysis of annealed specimens it was suggested that the high density of the ß-fiber components after IA and the small amount of stored strain energy of CR2 introduced by the lower cold-rolling reduction remained the ?-fiber components even after solution treatment.INTRODUCTION Al-Mg-Si alloys have been applied to automobile body applications, due to their excellent paint-bake hardening (age-hardening) and corrosion resistance compared to other aluminum alloy. On the other hand, the mechanical properties and deep drawability of Al-Mg-Si alloys are inferior to those of steels. Thus, it is important to improve the mechanical properties and deep drawability in order to expand the application components. One of the best methods to improve the deep drawability is to increase the Lankford coefficient (r-value). Previous studies reported that the increase of the average r-value ( ) improves the deep drawability. The relationship between the r-value and texture of the alloy is also well known. Inoue et al. reported that the ß-fiber components, such as Brass ({011}<211>), Copper ({112}<111>) and S ({123}<634>), increase the r-value measured in the direction of 45o with respect to the rolling direction. r"

Jan 1, 2018

By M. G. Goudge

IT IS ENOOURAGING indeed to note during the past year that, despite a slackening off in many markets and with numerous major difficulties and problems to solve, the mining industry of Nova Scotia was maintained at a very high level. The value of the Province&apos;s mineral production for 1957 amounted to approximately $65,000,000. This represents a drop of only 1.5 per cent from the figure of the previous year. Coal Atlantic Collieries, Ltd., opened a new coal mine during the year at Bras d&apos;Or. This colliery is equipped with the most modern type of mechanical equipment available, with transport of the ?coal by a belt-conveyor system. Other mines in the Province continued to mechanize their operations by the addition of Diesel haulage locomotives and other mechanized mining equipment. New wash plants are in operation and .an additional one is planned.

Jan 1, 1958

By Franc R. Joubin, Donald H. James

"The Property of Rix Athabasca Uranium Mines Limited is in the Beaverlodge area of northwestern Saskatchewan. The mine is 7 miles by road north from the Lake Athabasca port of Bushell which is 250 miles north by aircraft or boat from railhead at Waterways, Alberta.The Rix property is a portion of the former DD 1 concession, obtained in 1949 from the government of Saskatchewan when private prospecting for uranium became permissible. The concession was prospected in detail during the 1950 and 1951 field seasons and a great many radioactive show-ings were discovered. Development and drilling were concentrated in two and later three of these areas, and by late 1952 enough ore had been indicated in the Leonard series and ""Smitty"" zone to justify underground development by adit-drift and shaft respectively.Four hundred feet of drift development on the Leonard No. 1 vein and the sinking of a two-level vertical shaft with related lateral development on the Smitty zone were completed in 1953. In April 1954 the Smitty section was placed in production at a rate averaging 100 tons per day, thereupon becoming the first privately owned post-war uranium producer in Canada. The ore is shipped for processing 12 miles by truck to the mill of Eldorado Mining and Refining Limited.Until recently all of the Company's production was drawn from the Smitty orebody. In April, 1955, ore production commenced from the faulted west extension of the Smitty structure, known as the Rix 62 zone, and from the Leonard No. 1 vein.The Smitty orebody (see Figure 2) is an intensely brecciated lenticular zone bordering both sides of the Smitty fault. The breccia areas are irregularly mineralized with pitchblende, very sparse galena, and pyrite in a gangue of feldspar, chlorite, calcite, and silica, all thoroughly soaked with fine-grained hematite to produce the locally-called ""red alteration"".Tenor of the ore currently being mined is classified information. The average grade estimated, prior to production, was 0.20 per cent (4.0 lbs.) U308 per ton."

Jan 1, 1949