Search Documents

By Å. Partapuoli, M. Henriksson, P. Wikström, J. Worth, G. Adolfsson

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB’s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

In the leaching and recovery of gold from copper containing gold ores using cyanidation, some copper minerals also dissolve which can have a detrimental effect on the process efficiency and economics. There are also environmental concerns with current operations discharging cyanide and copper cyanide species into tailings dams, and strict regulations prohibit this for greenfield plants. Cyanide destruction however is not an economic option for new plants treating copper-gold ores. This paper evaluates a potential recovery process to overcome the copper cyanide problem. Despite gold dissolution occurring in copper cyanide solutions having no free cyanide, gold recovery from ores is lower compared to free cyanide. Thus, cyanide addition has to be optimised to maximise the gold recovery whilst endeavouring to eliminate free cyanide at the completion of leaching (CN:Cu less than 3:1). Subsequently, copper cyanide can be recovered using activated carbon. The loaded copper cyanide is easily recovered from the carbon with a cyanide soak and distilled water wash such that the eluted CN :Cu ratio is less than 4:1. The copper could be recovered efficiently by electrowinning, by decreasing the pH of the eluant to 5. The remaining cyanide solution, after electrowinning, is then neutralised to form NaCN and recycled.

Jan 1, 2005

By L. A. Mells

"A laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the applicability of a radium selective ion exchange complexer for removing radium from Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. under contract to the Department of Supply and Services using the Saskatchewan Research Council facilities located in Saskatoon, Saskatchewan.The results of this work showed the ion exchange complexer, Dowex XFS 43230.00, to be efficient in removing radium from contaminated water of uranium mining operations with the ultimate loading capacity of the resin on one type of water treated being determined as approximately 1,600 Bq/cm3 of new resin. Although this resin has potential application for treatment of effluent streams in uranium operations it has been identified that the resin efficiency and capacity is directly related to the chemistry of the water being treated and site-specific testwork is required in order to establish reliable design data for full-scale operations.IntroductionThe possible applicability of a radium-selective ion exchange complexer for removing radium from Canadian uranium mining effluents had been identified and discussed as a possible alternative to present radium removal methods during a review of disposal technology options for the National Uranium Tailings Program of the Department of Energy, Mines and Resources(1). Work by other workers(2.3) had shown the complexer to be very efficient in removing radium from contaminated water. Also, plant trials on contaminated minewater at the Mt. Taylor uranium mine in New Mexico is reported to have shown the resin complexer to be efficient under plant operating conditions.As a result, a laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the suitability of this resin for Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. (MCEL) under contract to the Department of Supply and Services using the Saskatchewan Research Council (SRC) facilities located in Saskatoon, Saskatchewan."

Jan 1, 1985

By Stephen C. Tadolini

"The use of a torque wrench to establish the amount of actual load developed on an expansion anchor bofting system dates back to work completed in the early 1950s. The advent of ultrasonic measurement systems and hydraulic torque wrenches has made it possible for the U.S. Bureau of Mines to perform torque-tension measurements in the laboratory and the field much more accurately. The results indicate that the amount of initial boft preload may be overestimated by amounts in excess of 45% of the expected load using torque wrenches. This inaccuracy is primarily due to the friction that occurs between the bearing plate and the head of the boft. These parameters become extremely important when the support system is being used to prevent joint members from slipping relative to each other or when the boft acts as a heavy spring to clamp two or more sections together. Methods to overcome the frictional losses are presented in conjunction with a laboratory method to determine the actual torque-tension ratios for expansion anchor and combination bolting systems.IntroductionMechanically anchored roof bolts have been widely used in the mining industry since their introduction in 1947. Estimates made in 1989 indicate that out of 85 million fixtures, approximately 49 million bolting fixtures still use applied tension to complete the reinforcement necessary to maintain stable openings. Nearly 85 million bolts are used yearly. The most widely used bolt is the resin-anchored headed rebar, followed by standard mechanical roof bolts, specialty bolts (mechanically anchored, resin enhanced fixtures) , and combination bolts . Po st-tensioned resin rebars, combination systems, and friction stabilizers make up the remaining 10% of the units used (Fig. I).For mechanical, combination, and tension rebar bolts, the bolt tension is the primary means of reinforcing the roof, but in many cases, because of poor installation procedures, the bolts are ineffective. Mine operators recognize the importance of proper installation procedures. Long-term bolt tension measurements are required in the Code of Federal Regulations (CFR)In each bolting cycle, the actual torque or tension of the first tensioned bolt installed with each drill head shall be measured immediately after it is installed. Thereafter, for each drill head used, at least one roof bolt out of every four installed shall be measured for actual torque or tension. If the actual torque or tension of any roof bolts measured is not within the range specified in the roof control plan, corrective action shall be taken."

Jan 1, 1991

By G. H. Hope, A. R. Maycock

"La Mine Doyon is a gold mining operation located in northwestern Quebec, approximately 35 km east of Rouyn-Noranda and 85 km west of Val d'Or. The mine is jointly owned by Lac Minerals Ltd. and Cambior Inc. with Lac Minerals as the manager. Production statistics as of February 1987 are 6.4 million tonnes milled at an average grade of5.8 g/t Au. Current reserves of9.9 million tonnes at 5. 7 g/ t Au to a depth of400m have been outlined. Indicated reserves below this horizon could considerably increase this reserve.The mine currently consists of two open pit and two underground mine operations, producing approximately 3600 tonnes per day of ore at an average grade of6 g/t. The ore is currently processed at the La Mine Doyon mill at a rate of1400tid and at Lac's East Malartic mill at 1950 t/d. Ore is also processed intermittently at Lac's Les Terrains Auriferes mill and at Noranda's Horne Division.La Mine Doyon is currently in the midst of a program to expand and upgrade the mill at La Mine Doyon. The expansion to 3000 t/day includes the conversion of the existing crushing and grinding circuits to a SAG (semi-autogenous grinding) mill circuit and the existing filter wash plant to a CIP (carbon-in-pulp) recovery plant. The economics of this project are based on reduced operating costs (milling and trucking) and improved recovery due to updated technology. HistoryThe area between Noranda and Val d'Or has a long history of mining activity in both base metals and gold, dating back to the early 1930s. More recently, several new orebodies have been discovered and exploited in the area including La Mine Doyon, Lac's Mine de Bousquet, Dumagami, and the Kiena operation.La Mine Doyon was discovered in the early 1970s, and brought into limited production in late 1979. The mine was started on are reserves of 2.75 million tonnes at 6.2 g/t and was, thus, considered a small, short-term operation. Mining started at an initial rate of 550 tI d with all the ore being shipped to Noranda's Horne smelter as flux. When Lac's East Malartic mill became available for custom milling, Doyon commenced shipping to that facility at a rate of 650 t/d. As a result of some equipment additions and an improved understanding of the ore, the East Malartic mill throughput was gradually increased from 650 t/d to the current rate of 1950 t/d."

Jan 1, 1988

By A. Iizuka

This study was aimed at separating and recovering arsenic, antimony, and tin from refining byproducts generated in a nonferrous smelter. The target byproduct was a silicate slag containing the above elements. The silicate structure of the slag was destroyed by alkali roasting, which then enabled leaching of arsenic, antimony and tin in solution effectively. Arsenic was selectively leached out by hot water after alkali roasting of the slag, while remained antimony and tin in the residue were leached out by a hot hydrochloric acid solution. However, when the solid-liquid ratio in the leaching solution was increased, hydrous gelatinous silica (gel-like silica) was formed during the hydrochloric acid treatment and filtration became difficult. Therefore, high temperature and high pressure leaching was attempted to improve the filterability of the silica leaching residue. In the high temperature and high pressure treatment, the hydrous gel-like silica was transformed into easily filterable aggregated silica, and thus, filtration became easy. By investigating the neutralization and sulfurization treatment for the obtained hydrochloric acid leachate (second leachate), it was possible to separate antimony and tin. INTRODUCTION This study aims to separate arsenic and recover valuable metals such as antimony and tin from refining byproducts generated in a nonferrous smelter. The target smelting byproduct is antimony-containing slag in this study. In many cases, alkali roasting was adopted as pretreatment for extraction and recovering valuable metals from smelting residues and wastes (Rao, 2006). For antimony-containing slag in this study, one effective method for separating arsenic is to convert arsenic to sodium arsenate (Na3AsO4) by roasting with a sodium compound and then to remove arsenic by hot water leaching. In addition, by alkali roasting, the silicate structure of the slag is destroyed, and effectively alkalizing tin and antimony is accomplished. Then, precipitating and recovering tin and antimony leached into the acid solution are considered possible by sulfurization and neutralization treatments. In this research, we conducted basic studies on the following. 1) Destruction of silicate structure in slag by alkali roasting and leachability of arsenic. 2) Conversion of hydrous gelatinous silica to aggregated silica by hydrochloric acid treatment of residues after arsenic leaching under high temperature and high pressure, as well as leachability of antimony and tin. 3) Separation and recovery of antimony and tin by sulfurization and neutralization treatments of hydrochloric acid leachate. These topics of investigation can support to consider the separation and recovery process of arsenic, antimony, and tin from antimony containing slag.

Jan 1, 2019

By Elaine Ellingham, Francis T. Manns

"The Orostar and Scadding were two small gold mines owned and operated by Orofino Resources Limited. Conventional statistical treatment indicates an identical arithmetic mean grade of 0.22 oz/T Au for both mineable reserves. Further, the deposits are both shown to have cut weighted average reserve grade of 0.21 oz/T. Orostar mined out at 0.206 oz/T and Scadding at 0.156 oz/T Au. The combined exploration and development database contained 1394 fire assays, more than enough for statistical confidence in a normal distribution. Therefore this study was initiated to determine, if possible, why the mill head grades were lower than the averages and to experiment with several methods to determine whether a reliable statistical mill head grade estimation method would emerge. Despite the identical reserve grades, distinct differences in the grade distribution histograms are present. By studying the arithmetic and log-normal grade distributions, with some attention to South African practices, this paper reports on those differences which may account for the considerable divergence in the mill head grades. Furthermore, this study casts considerable doubt on the industry standard method of cut weighted averages.The global mill head grades of the two deposits have been derived from the arithmetic average grades by graphic means. This precise method of mill head grade prediction, if applied to complex orebodies, could permit selective grade control and result in direct cost savings by allowing the operator to detect false value stopes, benches or levels and emphasize reliable regions of not only gold mines, but also uranium or base metal deposits."

Jan 1, 1992

By J. Kochhar, Robert G. Cooper

"The Cape Breton Development Corporation is a federal Crown corporation which was formed in 1968. Initially, the Corporation had two divisions - the Industrial Development Division, whose purpose was to stimulate Cape Breton Island's economy, and the Coal Division with a mandate to phase out the operating coal mines. However, that strategy changed in the early 1970s with the Middle East oil crisis. As a result of that crisis, Nova Scotia Power Corporation adopted an ""off oil"" policy. Today, approximately 700/0 of Nova Scotia power needs are met by generation of electricity from coal. Therefore, since the early 1970s, emphasis has been on the rehabilitation of the Cape Breton coal mining business with the opening of three new mines.Today, Devco is solely a coal mining company which employs 3300 people.Physical DescriptionThe mines operate in the Sydney coal field which is located on the eastern tip of Cape Breton. The Corporation leases the deposit from the province of Nova Scotia and its leases cover all coal from the outcrop to the 4000 ft depth. The seams outcrop along the shoreline and dip beneath the ocean floor at dips varying between 5% and 100%.There are eleven seams, of which three - the Harbour, Phalen, and Hub - have been extensively mined."

Jan 1, 1990

By Rocky (Yaokun) Wu

Rock burst is one of the biggest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost effective yielding rock bolt. This paper introduces a new yielding rock support - Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150 ~ 250 mm of deflection at 8 ~ 10 metric tons (Mt) loads for every 16.4kJ energy input. Its performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described, the dynamic testing results are discussed; and the features and application of the bolt are presented.

Oct 1, 2010

By G. D. Just

"Extensive mechanization of underground mining operations, improvements in blasting technology and the development of simulation models for systems evaluation has now made it feasible to optimize rock fragmentation and materials handling operations. Methods of achieving these objectives are described in this paper, with particular emphasis on the need to obtain precise field data measurements. Techniques are illustrated with reference to the sub-level open stoping system of mine production. IntroductionThe primary objective to be achieved in any mining system is to deliver a specified grade of ore to the mineral processing plant at a planned delivery rate and at the minimum total mining cost. Design and management of such a system is complicated by the large number of unit operations and the often unknown inter- relationships between the different unit processes. This particularly applies in underground mines, where planning restrictions and unit costs are much greater than in comparable tonnage sur face mining operations. These difficulties can often be resolved by the application of judgment based on extensive experience, but the costly trial -and-error methods required for new technology discourage innovation.Most modern medium- and large-scale mines are now extensively mechanized. Consequently, the performance of each unit operation by individual items of equipment should be predictable for a given set of conditions. An essential prerequisite is that quantitative performance data are available from field measurements. Such information can then be used to optimize the design and management of the complete mining system to achieve the minimum tot al mining cost. One of the most significant factors influencing all unit costs is the degree of rock fragmentation. The importance of this variable is indicated by the fact that opt imization of rock fragmentation implies minimization of tot al mining system costs."

Jan 1, 1980

By V. Silins, J. Tameling, R. C. Cook

"A general review of the wear problems encountered in the mining industry is presented and current practice for wear protection systems is reviewed.A new concept in wear protection is described and compared to alternative systems. Utilization of conventional stud welding technology and abrasion-resistant wear studs is shown to be a useful supplement or substitution for conventional techniques. Operating life of many consumable components can be increased by up to four fold. The technique is highly portable for on-site field application or can be used in shop environments.Details of the wear protection model and metallurgical properties of the wear component are also reviewed. Laboratory wear test data are reported to supplement field test performance or to screen potential alloy compositions for application in specific environments.A Review of Wear Problems and Wear ProtectionThe emphasis on wear protection has increased in recent years because of the increasing impact of the potential savings in time, materials and energy. A 1974 German study concluded that attention to tribology, the study of friction and wear, could save approximately $3 billion, and a study in the U.S.A. at the same time put the figure at $100 billion of which $20 billion was for materials. A more recent American study put the energy component of the potential savings at $16.2 billion per year. A recent British study estimated the total potential savings in the U.K. as $1 billion per year, with the largest savings coming from lower maintenance and replacement costs ($500 million), lower breakdown costs ($250 million) and increased machinery life ($200 million). These three major contributions are all potentially accessible in the mining industry."

Jan 1, 1982

By J. E. Nesset, E. R. Bobicki, K. L. Bilaniuk

The introduction of froth flotation technology in Canada, and in particular, in British Columbia, began not long after it was successfully applied in the Broken Hill mining area of Australia which began around 1905. It proved to be a revolutionary and transformative technology that resulted in marginal operations in copper, lead and zinc becoming profitable in spectacular fashion. The paper presents the technology of both oil flotation and froth flotation in the context of the challenges of the time and its early application in British Columbia at the Le Roi No.2 mine (1903), the Britannia Copper mine (1912), and at the Allenby concentrator of the Copper Mountain mine (1918-19). New-found archival documents indicate the Britannia application to be the first production application of froth flotation for copper ore outside Australia, a claim that is currently made by the Braden mine (now El Teniente) in Chile. Flotation was initially an add-on process following gravity methods but was rapidly shown to be far superior method for the bulk and selective recovery of metal sulphides. Flotation proved particularly successful for the recovery of zinc sulphide (the so-called ‘zinc problem’) which was considered a contaminant at the time. The ‘copper problem’ related to the poor recovery of fine copper sulphide particles that were not amenable to gravity methods. The success of flotation led to changes in both the scale and methods of mining, concentration and smelting in a manner that allowed integrated mining companies to flourish. Many are still with us today. INTRODUCTION The advent of froth flotation in the early 20th century was truly a revolutionary technological development, not only for the mining and metallurgical industries, but arguably more so for business and society overall. The Canadian technology historian Jeremy Mouat stated (1996) “The development of flotation was the greatest single metallurgical improvement of the modern era...it is not overstating the case to claim that flotation was of central importance to the smooth functioning of the global economy”. It should, therefore, be a story of interest to us all. The aim of this paper is not to retell the full story, that has been well covered by others (Hoover, 1912; Rickard, 1916a; Hines & Vincent, 1961; Lynch et al., 2010) but rather to add some Canadian perspective and the key role played by companies and individuals in those early days, focusing on events in British Columbia’s copper industry. EARLY DEVELOPMENTS During the later half of the 19th century, a number of flotation-related patents were issued. These include the 1860 patent (Britain) granted to William Haynes for a process to separate sulphides from ground ore by mixing it with oil (1-10% wt) followed by a separation process in a water-filled vessel; the 1877 patent granted to Georg and Adolph Bessel (Germany) for a process involving the mixing of oil and graphite ore followed by boiling in water to produce a high grade graphite froth (>90% carbon); and the 1885 patent granted to Rebecca ‘Carrie’ Everson for the separation of sulphides by mixing sulphide ore with small quantities of oil, and adding water followed by sulphuric acid. These processes are more properly referred to as bulk oil flotation due to the relatively large quantity of hydrocarbon used.

Jan 1, 2019

By Shahram Tafazoli

ABSTRACT: This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Gerald S. Cole

It used to be that a science/engineering presentation on "light weight" at a metallurgy conference, would relate to the materials science, processing, component fabrication and applications of aluminum, magnesium and titanium. Within the automotive industry, light weight now includes how to "lighten up", how to lightweight, or how to mass reduce vehicle components and systems. Increasingly stringent global emissions-reduction requirements require increasing vehicle fuel efficiency; mass reduction is an enabler to achieve this. While light metals certainly are the basis, a host of other materials can be used to optimize mass reduction while meeting vehicle performance, safety and cost requirements. New grades of ultrahigh strength steels and even nanosteels can be thinned down and save over 1/3 the mass vs conventional mild steels. A compacted graphite cast iron engine can be made lighter than an aluminum one. Aluminum components in vehicles were only castings; now aluminum stampings, forgings and extrusions are becoming more visible components of mass reduction. Lower mass high temperature polymers, and carbon fiber polymer composites now replace aluminum and steel. These materials often require specialized processing and manufacturing techniques to produce a component, including superplastically formed twin roll cast sheet aluminum and magnesium, and hot stamped/in-mold quenched steels. The assembly of hybrid structures requires unique joining/bonding, and corrosion-inhibiting techniques that might include sophisticated structural adhesives. This thinking "light" presentation, will conclude with a discussion of U.S. and Canadian government engineering and research support for mass reduction, including the proposed $148 M American Lightweight Materials Manufacturing Innovation Institute.

Jan 1, 2014

By C. Bourgoin

"The factors constraining productivity in the mining of narrow vein ore deposits are numerous and often interdependent. This paper concerns mining techniques capable of reducing some of these constraints in the case of vein deposits whose dip is less than 45 degrees. Modifications of conventional mining methods as well as suggested new developments are presented, as are matters pertaining to the mechanization of operations as a mean of increasing both productivity and work safety. IntroductionThe mining of vein deposits, whose width (thickness) is generally less than 2 metres and whose dip is often variable, calls for the use of varying stoping procedures as well as appropriate infrastructure and equipment. In the case of intermediate dips (15 degrees to 45 degrees), it is generally conceded that the degree of mechanization is limited and that ore removal via gravity is impossible. This paper proposes certain innovations in matters of equipment use and stoping methods, together with certain technical data pertaining to the application of these new procedures Stoping MethodsTo mine vein deposits, one must choose a method that can adapt to irregular ore limits and allow, as well, for good ore recovery with as little dilution as possible. In addition, it is important to minimize development work in waste rock. In principle, one selects a method that is both safe and profitable; this method will be defined mainly by the nature of the vein deposit and its dip, by the competency of the rock formations and by certain technical considerations. Moreover, the stoping procedure in a given deposit may well change with time as a function of new layouts or new equipment."

Jan 1, 1994

By John D. Smith, Robert J. Mitchell

"There is a world-wide trend toward underground bulk mining methods employing hydraulically placed backfill. This trend is recent and therefore there is little in the literature to assist an operator in the design of backfill properties, the design of drainage facilities, the calculation of the operating forces on a bulkhead, and the control procedures considered necessary before, during and after pouring. This paper presents recommended procedures that are based on over to years of experience in the various aspects of backfilling large openings. Free-draining timber or concrete block bulkheads are shown to be a viable alternative to massive reinforced concrete bulkheads for the containment of backfill pours. Hydrostatic pressures cannot develop in backfills provided adquate drainage facilities are installed.IntroductionThe increasingly adverse relationship between mining costs and mineral values has led mining companies to develop more productive, lower-cost, bulk mining methods. This has led to the increasing use of large, more or less continuous, hydraulically placed backfill pours to enable the recovery of a higher proportion of pillar ore. The success of any bulk mining method depends on the degree of stability maintained during the stoping operations with reference to the mining rate, the performance of the backfill with respect to the per cent extraction of pillar ore, and the control of the mine structure with respect to safety and productivity. One such method has been previously described(I) where a steeply dipping orebody is being mined with a sub-level method that employs large, hydraulically placed tailings pours for delayed pillar recovery. The paper describes the rock mechanics analysis undertaken to establish the stope and pillar geometry and the approach taken to establish backfill strength requirements to prevent dilution during pillar recovery. Production with this method started in 1970 and because few, if any, large bulk pours had previously been used in- this way (judging by the lack of information in the literature), design data and criteria were needed for several aspects of the work. Methods to establish backfill quantities and pertinent ""in-place"" fill properties are described in 2, 3 and 4 in the list of references. Results of field measurements taken to establish fill pressures for bulkhead design purposes are described in 5 and 6. Laboratory large-scale model tests undertaken to confirm a fill strength design equation, which takes into account fill arching, have recently been completed. A paper describing these tests and the results will be forthcoming in the near future."

Jan 1, 1982

By E. Topuz, C. Duan

"INTRODUCTIONOperations research (OR) applications have experienced a substantial growth within the mining industry during the last three decades. The purpose of this paper is to present a summary of the results of a comprehensive survey of the application of various OR techniques to the major mining activities. It is hoped. through this sur vey , that the most widely used OR approaches, the important areas of application, and future trends have been identified.This survey included more than 500 articles published in this field in English since the late 1950s. Most of the relevant literature was found in mining publications, but, in terms of quality and originality, important applications were also found in literature not related to the mining industry. The sources constituted periodicals, proceedings research reports, and a few books. A listing of selected publications from which three or more articles reviewed in this survey appear is given at the end. Operations Research MethodologiesOperations research is concerned with optimal decision making in, and modeling of, deterministic and probabilistic systems that originate in real-life situation s. One basic feature of the OR methodologies is the attempt to optimize certain design parameters, subject to a set of constraints. This distinction has been employed in the survey as a guideline for selection of the techniques covered under the title "" OR methodologies"". The methodologies thus encountered in the literature are listed below. In a few cases, simulation has not been considered because it is not an optimization method per se."

Jan 1, 1989

By A. LA. Salama, D. B. Hyma

"The Western Research Centre (WRC) of CANMET located in Devon, Alberta, is a modern research facility offering services ranging from fundamental research to pilot plant investigations. Recently, a 0. 76 metre diameter by 7.9 metre high Flotaire column flotation cell was installed as a demonstration unit for Canadian coal producers. Because the column cell is intended to be used for research, development and demonstration, WRC recognized that additional sensing equipment and improved process control would be required to generate good data for subsequent column scale-up and engineering design.A low cost, personal computer based control system was, therefore, designed and installed. This paper describes the stepwise procedure in developing the control strategies, selection of system software and hardware, and installation and configuration of the system.Preliminary performance data on a western Canadian coal sample are also presented. Future testwork is planned on additional coal samples to expand upon existing database."

Jan 1, 1993