Search Documents

By L. G. Morrell

Introduction A Self-Dumping cage which combines the features of a small skip and a cage has been used in a vertical winze between the 2,000 and 2,500 levels at the Coniaurum mine for the past three years, during which time its success has been demonstrated by uninterrupted service and low maintenance charges. lt was designed by John Reddington, mine manager, and was built under his supervision in the Coniaurum mine shops. Being new in many of its operating features, a small-scale model was made and tried before the final construction was undertaken. The mechanical performance of the model suggested a few minor changes that were incorporated in the final drawings. During its three years of use, the automatic dumping device has saved the expense of deck-handling of the cars. This actually represents a gross economy of something over four times the cost of construction and installation, which totalled $1,325. The cage, empty, weighs 2,200 pounds, of which 500 pounds represents the weight of the dumping accessory and necessarily heavier construction. Besides a considerable financial saving, the time saved in unloading increases the daily hoisting capacity of the winze. In raising ore from the 2,500 level, five minutes are required for a complete trip. Allowing one minute for the alternative of decking, we believe that the automatic dumping has increased the capacity of the winze hoist nearly 20 percent.

Jan 1, 1933

By J. G. Mieczaniec

"A key element for a successful mining operation is the grinding circuit. It must be reliable, maintainable and must perform to or above design capacities for 95% of the time. Once chosen and installed major modifications are either prohibitive or very expensive. The selection of mills and drive system is probably the single most important decision made within the concentrator complex.Economic studies revealed that the optimum expansion for Lornex was a 68070 increase in plant throughput. This indicated that the new mill would have to be larger than the existing 32-foot mills.The Lornex ore has a wide range of hardness which has a great influence on mill throughput (Table 1). To smooth out the fluctuations, a blending program ha s always been in effect at the mine, coupled with ball charge control for the primary mills. As can be appreciated, an optimum balance is difficult to achieve. A sudden change to so ft ore with a high ball charge puts the mill into jeopardy with a constant speed drive.The blending philosophy would continue after the expansion, but with the addition o f a second primary crusher, it was envisaged to have the new mill process harder ore to maintain production targets. In theory, the new mill would have a proportionally larger ball charge than the existing mills.This scheme makes the new mill vulnerable for processing so ft ore for a fixed speed mill. Thus, variable speed seemed an attractive option.In early 1979 prominent mill manufacturers were invited to submit proposals for the new mill. Fixed and variable speed mills were to be considered with mill size ranging from 32-foot to 36-foot diameter. The proposals were to include the drive, ball charge, % critical speed, couplings, gears, etc. - the complete package. The recommendations were variable with most manufacturers submitting several alternatives. Recommended mill speed varied from 68% to 78% critical. The concept of variable speed was becoming more attractive, Lornex ultimately decided on a twin DC motor drive system for a 34-foot diameter mill.After start-up it was discovered that best throughput occurred at 78% mill critical speed or top speed of the drive motors. The motor speed range was adjusted upward from 186 to 200 rpm. Today the mills operate at 79% critical or a motor speed o f 193.5 rpm.Clearly the selection of the variable speed mill allowed the flexibility to optimize throughput."

Jan 1, 1985

By Y. W. Pan, Y. R. Liu

The disturbed natural rock mass tends to equilibrium state accompanying with non-equilibrium evolution process which has significant influence on the long-term stability of engineering structure. The deformation development in the non-equilibrium evolution is determined by two intrinsic processes, trend to equilibrium and damage development, which can be illustrated by evolution of excavated tunnel. Thus the creep and damage must be taken into account in study of non-equilibrium evolution process. Within Rice’s irreversible thermodynamics with internal state variable (ISV), the conjugate force function which equals to zero is a convex surface which divide the stress space into two parts, called equilibrium and nonequilibrium stress space respectively. The concept of effective stress of non-equilibrium has been proposed, in which the stress difference (d - d ) are the effective driving forces of non-equilibrium evolution process with hardening and damage effective. The formulations of inelastic strain rate and energy dissipation rate have been recast in the form of effective stresses. The inelastic complementary energy (ICE) is proposed to measure intensity of non-equilibrium evolution of material system. The specific equations of conjugated forces and kinetic equations of internal state variables are presented. The ICE and rate of energy dissipation are all calculated to be used to evaluate long-term stability of geo-engineering. The results show that rate of energy dissipation may be more convenience and flexible than ICE for internal state variable constitutive equation of rock mass.

Jan 1, 2015

By David Davidson

Overview- Points To Be Addressed ? Review the building blocks of a successful and vibrant industrial economy ? China?s current position in the global economy ? China?s voracious appetite for raw materials ? Distortion in import/export trends ? Areas of strategic importance for China - Steel and its components - Agriculture self sufficiency - Energy now and for the future ? Do current valuation techniques fairly value ?strategic? assets? China ? The Economical Miracle - Massive shift in population from rural to urban - ?Middle class? growing rapidly, hence strong consumer growth - China is the manufacturing center for the world ? cheap labour and - modern facilities - Infrastructure build out ?US$585b stimulus package and 5 year plan - Rail ? 30,000 kms of new track planned by 2020 - Power ? 50% capacity increase, including 35 nuclear reactors - 100 major new airports - State of the art process and manufacturing facilities - Port capacity ? 100m TEU capacity increase by 2020 Class 1 national highway ? 35,000 km?s by 2020

May 1, 2010

By X. Cao, H. Huang, Z. Dai

"Crystal phase of copper-containing slag regulation by the slag viscosity, cooling speed and cooling method, where the slag viscosity is related to the temperature and alkalinity. According to the mineralogy properties of a copper-containing slag, experiments of crystal phase regulation and flotation were conducted. When the copper-containing slag that adding a small amount of calcium oxide was cooled slowly at a rate of 3°C/min and about 1050°C n a cinder inclusion system, the viscosity of slag can be remained under 0.25 Pa·S and more than ??% of copper particles that the grain size is larger than 20 ?m in slag. The whole flow of flotation experiment was carried out to recover copper from the copper-containing slag with crystal phase regulating and the copper concentrate grade was ?????%, the recovery efficiency of copper was 94.18%.INTRODUCTIONChina's annual output of copper slag is more than 6 million tons, the current total has reached 80 million tons. It is equivalent to 640 thousand tons of copper metal with the copper grade of 0.82%. Most of the smelting slag were storage. It is not only occupy the land and pollute the environment, but also make a huge waste of resource (Alp, Deveci, & Süngün, 2008; Carranza, Iglesias, Mazuelos, Romero, & Forcat, 2009; Gorai, & Jana, 2003), therefore, it is good way to achieve copper slag resources by the effective recovery of valuable component from copper smelting slag, which is an important measure of the current process of copper smelting slag and implement the central authorities to vigorously develop the circular economy, improve the recycling of resources, increase copper production of intensive development (Zhou, et al., 1994; Zhang, Zhang, & Wang, 2005). Currently, researches on comprehensive utilization of the coppercontaining slag made a much progress (Wei, 2004; Liu, Gai, Yang, Sui, Li, & Fu, 2008; Liu & Zhu, 2008; Zhang, 2010; Sun, Chen, & Tang, 2012; Qin, Wang, Ren, Wei, Peng, & Gu, 2012). Flotation is one of the most effective method to recover the copper from smelting slag, which has the features of low cost and high efficiency (Song & Liu, 2001; Zhang, Wang, & Li, 2012). But the copper particles in the copper smelting slag distribution is very uneven, and the thickness of the material is very serious. The copper content in the micro level is higher, the size of copper sulfide ore is less than 0.043 mm, which leads to the difficulty of the monomer dissociation (Tossavainen, Engstrom, Yang, Menad, Lidstrom, Larsson, & Bjorkman, 2007; Moustakas, Mavropoulos, Katsou, Haralambous, & Loizidou, 2012). In this study, according the process mineralogy of a smelting copper slag, the crystal of smelting copper slag was optimized by controlling the temperature, alkalinity, cooling rate and cooling method, which makes the fine copper mineral particles in the copper slag crystal further, and can be used to meet the particle size requirements of flotation, thereby enhancing the flotation of copper."

Jan 1, 2016

By D. V. Ziehlke, J. M. Franklin, T. M. Gordon, A. G. Galley

The Snow Lake-Wekusko Lake region of northern Manitoba conta ins numerous lode gold occurrences, including the largest gold deposit in the Churchill Prov ince, the Nor Acme mine. The Aphebian volcanic and sedimentary rocks of this region are comprised of submarine volcanic strata, overlain by turbidites, both of the Amisk Group, and fluvi atile sedimenta ry strata and bimodally composed subaerial volcanic rocks of the overlying Missi Group. Gold occurs as: 1) accessory gold in volcanogenic massive sulphide deposits, 2) lode gold in shear zones related to sy n- to post-FI thrust fa ults, and 3) lode-gold associated with post-F2 fault . An alteration a emblage of biotite, al bite and calc ite is associated with both groups of lode-gold deposits, and has been superimposed on the regionall y-developed metamorphic assemblages. AJthough these deposi ts are spatial ly related to britt le-ductile faul ts of different initial ages, they appear to have all fo rmed after the major period of reg ional fo lding and metamorphism, and thus may be penecontemporaneous. The alteration is different from the sericite-ankerite-quartz assemblage that is typically associated with gold deposits in Superio r Prov ince. Deposits in thi s area of Churchill Prov ince may have formed either at a higher temperature or a deeper structu ra l level than tho e in Superior Prov ince.

Jan 1, 1986

By Christina Graf

A synthesis of colloidal gold shell particles with a silica core is described. Small gold nanoclusters were attached to the functionalized surface of colloidal silica particles. Reductive growth and coalescence of these clusters lead to the formation of a closed gold layer. By variation of the thickness of this gold layer and the radius of the shell it is possible to adjust the plasmon resonance of the gold shell particles over the whole visible and infrared region of the spectrum. The optical properties of the particles made are in good agreement with theoretical calculations for coreshell particles. Due to their low polydispersity these gold shell particles form in solution large crystals with submicron lattice constants. It is also possible to produce hollow gold shells by dissolution of the silica core. A new method to coat the silica core gold shell particles with an additional outer silica shell is also presented. This allows due to a reduction in the Van-der-Waals forces to make more permanent dried crystals and facilitates functionalization of the particles for use in various photonic applications.

Oct 1, 2003

By J. E. Nesset, F. Rosenblum, J. A. Finch, R. Payant

ABSTRACT Under certain conditions of moisture and oxygen, sulphides can spontaneously self-heat. We tested a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by the rest potential difference between sulphides and particle size. A series of binary sulphide mixtures was tested. Individual sulphides and mixtures with low rest potential difference did not self-heat, but mixtures of high rest potential difference did. When testing pyrite-sphalerite mixtures, self-heating increased inversely with particle size, with the fineness of the pyrite governing self-heating, indicating the rate-limiting step is the reduction reaction. The results support the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on hydrogen sulphide as an intermediate product is proposed. The understanding gained will be of interest to those involved in storage, shipping, and disposal of sulphides.

Jan 1, 2012

By Graham A. Davis, Michael Samis

The dramatic fluctuation in metal and energy prices in the last few years is causing mining companies to consider alternative analytical methods for mine design and valuation. The goal is to improve insight into unforeseen changes in the economic and project environment and to design projects that take advantage of management's ability to respond to these changes. Such flexibly managed projects will contain value that cannot be measured using traditional engineering economic approaches, further motivating the used of alternative, modern valuation methods. This paper considers the valuation of an uneconomic low-grade resource at an open pit gold mine using two of the most popular modern valuation methods, Dynamic Discounted Cash Flow and Real Options. Our analysis demonstrates that the conventional valuation method may incorrectly represent the value and risk attached to mining this type of resource because it is unable to recognize management's ability to respond to future events in a manner that minimizes losses and exploits advantageous business conditions. The results of this paper highlight the importance of recognizing flexibility and business uncertainty in both mine design and valuation.

Jan 1, 2003

By Rodney A. Cooper

The Mary River iron ore deposits were discovered in the 1960?s. The high quality of the deposits was immediately evident, and drilling programs were successful in defining a resource adequate for supporting a feasibility study. Through a combination of ownership, market and political forces, the deposits were not developed. Having missed the window of opportunity, the project remained dormant for over three decades. Baffinland Iron Mines Corporation, with its 100% ownership of the Mary River deposits, began trading publicly in 2004. Modern exploration and metallurgical test work began in 2004 and has continued in 2005 and 2006, resulting in total expenditures during this period of almost C$60 million. In May 2006, an engineering team lead by Aker Kvaerner E&C, a division of Aker Kvaerner Canada Inc., completed a scoping study based on the first of five identified deposits. Highlights of that study include direct shipping of high quality lump ore to Europe over a 34 year mine life at a production rate of 10 million tonnes per annum, based on an indicated resource of 309 million tonnes at 66.1% Fe and an inferred resource of 28 million tonnes at 65.9% Fe. Capital costs were estimated at C$1.5 billion. Using iron ore prices approximately 36% below that of the 2006 market, a pre-tax internal rate of return of 15% was estimated assuming equity financing. Payback on initial capital was 5.9 years. The pre-tax life-of-mine cash flow was estimated to be C$6.3 billion. As a result of this study, Baffinland initiated a Definitive Feasibility Study, under the management of Aker Kvaerner, which is scheduled for completion in December 2007. This paper touches on the geology of the deposits, the current resource and the outlook for expansion. Project permitting, construction planning, logistical challenges and ocean shipping considerations are discussed, providing a current perspective on the project scale, scope and timeline for commercial production. In addition, an overview of the Company?s bulk sampling program will be provided.

May 1, 2007

By J. Lu, D. G. Ivey, H. Henein

Microalloyed steels are widely used in the oil and gas industry. They are a class of high strength, low carbon steels containing small additions of niobium (Nb), titanium (Ti), molybdenum (Mo) and/or vanadium (V). These steels have good strength, toughness and excellent weldability, which are attributed in part to the presence of nano-sized carbides, nitrides and carbonitrides. In the pursuit of developing higher strength microalloyed steels, it is of great interest to quantify the size, distribution, volume fraction and chemical speciation of these precipitates. However, characterization techniques suitable for quantifying fine precipitates are limited. Possible characterization techniques include SEM, TEM and matrix dissolution. A comparison is presented of the various techniques.

Jan 1, 2005

By A. G. Scobie

A spectrographic method for the determination of small amounts of gold and the platinum metals in ores has been developed. By means of this method, an assay of 0.001 ounce per ton on one assay ton samples is possible, and by seecrrographic adjustments the sensitivity may be increased to 0.0001 ounce per ton. All the prec10us metals may be determined from one spectrographic arcing with an accuracy of about 5 per cent average deviation from absolute values, and the complete analysis of an ore or similar product may be reported five or six hours after receipt of sample.

Jan 1, 1945

By K. K. Dehn

This study focused on determining the stability of thin shotcrete fill fences at a hard rock mine in northwestern Ontario during increased pour rates of paste backfill. Determination of the stability of the fence is needed for both personnel safety and to avoid failure of a fence. Failure of a fill fence during backfill activities would have severe impacts on production and potential hazards to nearby workers. Approved fill fences at the mine are a slender design of 10.5 centimeters of shotcrete applied to a rebar framework with burlap lined ?bedspring? backing. Approved mine standards dictate that fill rates may not exceed 1.5 meters of paste depth per 10-hour shift when pouring behind a flat fill fence. To decrease the backfill cycle time the study looked at fence stability during increased pour rates of 2.5 meters paste depth poured within a 10-hour shift. An instrumentation design was developed including pressure cells, strain gauges, and tilt-meters that were built into experimental fences to observe the effects of increased pour rates on lateral wall pressures, strain development in the rebar and shotcrete reinforcement, and physical deformation patterns along the face of the fence. The data was analyzed for overall stability.

May 1, 2007

By DONALD E. BARNETT

Since the days of early settlement ew Brunswick has produced a variety of industrial minerals but it is perhaps only the recent discoveries of significant reserves of potash that have elevated the meaning of industrial minerals in their contribution to the provincial economy. With potash production commencing in July 1983, the role of industrial minerals will increase significantly to the value of mineral production in the province.

Jan 1, 1984

By I. Kylmakorpi

In non-ferrous metal smelting, when the concentrate entering the furnace contains high levels of moisture, energy requirement for heating and drying increases and large volumes of exhaust are produced. To solve this problem, rotary dryers and flash dryers using direct heating, and also steam dryers using indirect heating have all been used for drying concentrate. The focus of this paper is to present the development and current applications of the Kumera Rotary steam dryer. The advantages of this technology are numerous, including reduced heating requirements, environmental friendliness, operation reliability and minimum maintenance needs; making it a top choice for drying concentrate.

Jan 1, 2008

By J. Stiksma, K. Buban, J. Oftsie, R. Kalanchey, S. Sadykov, E. McConaghy

The Kazakhmys zinc refinery in Balkhash, Kazakhstan, which employs the Dynatec Zinc Pressure Leach Process, officially launched autoclave operations on December 27, 2003. The Kazakhmys plant is the world's first greenfields zinc refinery based on Dynatec's two-stage pressure leach technology. Production of zinc was realized on February 9, 2004, when the first cathode was stripped. Currently the plant start-up is ongoing, with progression to two-stage zinc pressure leach operation and ramp-up to full design capacity continuing through 2004.

Jan 1, 2004

By Wm. D. Jr. Sheldon

THIS paper presents practical data to aid in the selection of a mine ventilating fan, and outlines considerations to be made to ensure satisfactory operation and optimum efficiency of the fan. Much has been published on the general subject of mine ventilation, but the writer has found few specific data on factors and considerations which govern the selection of a fan-data which should be available to the operator if his fan is to give satisfactory service within the range of the high-efficiency portion of its performance curve and deliver the specified air capacity when operating against the anticipated range of resistance of the mine. The total quantity of fresh air furnished by the ventilation system must be adequate to provide, and to ensure at all times, safe and healthful working conditions in the mine. It is assumed that the mine operator is able to determine the air quantities required for the various parts of the mine.

Jan 1, 1941

By H. R. Stoger

"In 1994 world trade grew by 9%, the fastest annual increase since 1976. Dry cargo shipping rates are at an all time high.Panamax size bulk carriers are receiving19 000 US dollars per day for trans Atlantic round trip voyages. This is good news for the ship owners but not such good news for the industrial users of ocean shipping.The main emphasis of this paper will be on bulk carriers, the charter market and what industrial companies can do to reduce their costs of ocean transportation which is critical to Canadian exporters. Let us look at the charter market in general.Bulk carriers come in four main sizes:1.The Capesize bulk carriers of 110 000 to160 000 tons that are primarily used to transport iron ore and coal;2.the Panamax bulk carriers of about 70 000tons dwt. This is the largest size (with a beam of 105 ft) that can transit the Panama Canal.3.the Handymax bulk carriers of 40/45 000tons dwt; and4.the Handysize bulk carriers of 20/35 000tons dwt.The handysize vessels are usually craned or geared and carry a variety of bulk cargoes including steel. Ship sizes have increased over the years and the mining industry now uses primarily capesize or Panamax bulk carriers.International chartering is conducted through an international network of shipbrokers. There is usually one broker representing the ship owner and another broker who represents the charterer. The major chartering centers are London and New York but a great deal of chartering activity is conducted in regional markets such as Hongkong, Oslo, Montreal and Hamburg.The Biffex Index or Baltic Freight Index is a good measure of dry bulk freight rates. The Biffex is composed of ten major routes. In May1995, the Biffex was at 2310 points. A year earlier it was at 1354, an increase of about 56%."

Jan 1, 1996

By Steven D. Botts

The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd. , is a $2.3 billion copper/zinc project, located in the Ancash Department in Perú. The project consists of an open pit mine, a 70,000 ton per day concentrator, a 302 Km. long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 million tonnes per year of copper and zinc concentrates over a 23-year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world. This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28th, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14th, 2001 by Peruvian president Alejandro Toledo. The construction stage of the project generated 8,000 direct jobs, with a peak of 10,000 employees, and 30,000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals; around 30% of whom came from the department of Ancash where the deposit is located. Approximately 5,800 indirect jobs will be generated from the project. Independent sources state that Antamina will increase the Peruvian mining exports by 30% and Peruvian GDP by 1.4% within its first year of full operation in 2002. Since winning the privatization bid for the project in 1996, the company has implemented a successful approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company?s environmental program. Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues, and as a result, has set new standards in Perú for environmental and community management, and sustainable development.

May 1, 2002

By R. M. Oliver

THE Falconbridge property is almost completely covered with over-burden to a depth varying from 60 to over 200 feet. This overburden consists of grave], sand, and boulder, with bands of very fine silt, and there is usually a layer of water-bearing quicksand adjoining the r:ock surface. In previous shafts sunk at Falconbridge, this water-bearing quicksand had given considerable trouble, and further difficulties were expected in sinking No. 5 shaft, due to its greater size. The method described in this paper is the one adopted in sinking this shaft, after the matter had been carefully considered. No. 5 shaft is located 2,400 feet east of the old main No. l shaft, and is sunk in norite in the hanging-wall of the ore-body, which is, however, ? practically vertical to the deepest known intersection. The greatest depths of overburden prevail on the south side, or footwall, of the ore-body, and this, together.. with the fact that the footwall is wet and more badly fractured, swayed the final decision to sink in the hanging-wall. After the shaft site had been chosen and cleared, a diamond drill was set up a few feet away and a hole bored to a depth of 405 feet to test the over-burden and character of the norite bedrock. The depth of overbudren indicated by the hole was Ill feet, with the last 10 feet water-bearing. The norite was rusted and broken up for only a few feet below bedrock. A steel sinking shield (Figure l) was assembled at the shaft location, and consisted of 5/8-inch plate, 5 feet deep, built around a frame of 6 inch by 6 inch angle-iron, and braced at the corners with the same material. Twelve-inch I-beams held the shield as rigid as possible. In order to reduce binding against pebbles to a minimum, the shield was constructed with a 1-inch batter on all sides.

Jan 1, 1938