Search Documents

By P. L. Schwartz

The present method of shipping potash to the myriad of consumers is inefficient, not only because of the extreme and unpredictable nature of seasonal demand, but also because railway car turnaround times are very lengthy. The Floating Train system employs unit trains of potash operating from Saskatchewan mines to distribution warehouses located throughout the six corn-belt states of Minnesota, Iowa, Wisconsin , Illinois, Indiana and Ohio, transshipment points at Thunder Bay and the U.S. waterway network, and, where applicable , large consumers. These unit trains would "float", meaning that they would not originate at the same mine nor terminate at the same warehouse on each trip . They would " float " freely among the origins, destinations and participating railways. The potash would be shipped uniformly throughout the year and usually stored in warehouses located within the six states. It would be subsequently delivered to consumers within a 75-mile radius. Distribution warehouses and rolling stock would be provided by a new company, Potash Distribution Limited, consisting of major potash producers and the Canadian railways. Potash Distribution Limited would be responsible for the distribution of potash from the origin through the warehouses to the final consumer. The additional costs of providing warehouse space and outbound delivery will be offset by the reduction in both rail rates and "peaking" expenses.

Jan 1, 1978

By A. C. Stevenson

"The most common theory is that, since thyristors, diodes, and insulated gate bipolar transistors (IGBTs) are “solid state” they will live forever. This is not so. They have wear-out mechanisms (e.g. insulation) and other mechanical parts such as motor bearings. These wear-out phenomena can be easily calculated. In this paper we will look at some of the failures and the failure rate of thyristors in power converters to see what affects them and to see what improvements can be made. If converter failures do occur, some simple forensic engineering steps will show if this is the root cause of the problem.IntroductionLook at the general failure rate curve for thyristors, diodes, gate turn off devices (GTOs) and IGBTs shown in Figure 1. We see that there is an initial high failure rate due to manufacturing defects, application problems, and drive start-up stresses that lasts for a few weeks. This is followed by a long period of (hopefully) several years with a relatively low but very slowly rising failure rate. At the end of this period, the devices start to wear out and the failure rate suddenly starts to increase rapidly over a few months. This signals the end of life for the devices in the system. We will start by looking at this end of life area."

Jan 1, 2000

By R. Kaibyshev, I. Zuiko

"The effect of thermomechanical processing (TMP) including cold working by tension or rolling before aging on mechanical properties and a dispersion of secondary phase particles of an AA2519 alloy (Al–5.64Cu–0.33Mn–0.23Mg–0.15Zr–0.11Ti–0.09V–0.08Fe–0.01Si (wt. %)) was examined. It was shown that the use of tension to impart pre-strain =10% in the alloy provides the best combination of properties in peak aging condition of the material. The AA2519T87 alloy processed by tension exhibits the yield stress, ultimate tensile strength and elongation to failure of 425.4±2.4, 475±2.4, 12.1±0.4, respectively. The one pass rolling leads to -5% decreases in yield stress and –20% decreases in ductility. Dislocations serve as heterogeneous nucleation sites for ?'-phase precipitation. The positive effect of tension is attributed to the formation of more homogeneous dislocation structure, uniform distribution of ?'-phase particles with higher aspect ratio. Precipitation of the O–phase plates on {111}a habit plane was detected. In addition it was shown that the low angle boundaries are heterogeneous nucleation sites for ?' and O particles.INTRODUCTION Precipitation-hardened alloys are a commercially important group of the materials because their mechanical properties can be modified by treating and changing the microstructure. Age-hardenable aluminum alloys belonging to the Al–Cu–Mg system are widely used due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance attributed to the highly efficient strengthening by the ?'-phase (Palmer, StJohn, Nie, & Qian, 2017). An AA2519 alloy exhibiting superior mechanical properties among high-strength Al–Cu alloys (2XXX-serie) due to minor Mg additives. It is known that, in alloys with high Cu/Mg ratio (=5.6) the classic precipitation sequence (Palmer et al., 2017; Wang & Starink, 2005; Wang et al., 2010) of supersaturated solid solution (SSSS) decomposition occurs: SSSS ? GP zones (Al3Cu) ? ?? (Al3Cu) ? ?' (Al2Cu) ? ? (Al2Cu) (1)"

Jan 1, 2018

By M. J. Fairweather

"The nature of minor element values and impurities are important both in the assessment of new properties and in the continuing improvement of operating plants. Impurity elements are frequently present as fixed solid solution impurities in association with the constituent minerals of a deposit or process streams in a concentrator. This paper uses five case studies to illustrate the application of simple regression analysis to the evaluation of minor element distribution in both operating mines and new deposits using analytical information readily available. This information maybe used to determine opportunities for improvements to the performance of an operating mine, to the economic assessment of anew deposit, or to the subsequent planning of an experimental study.IntroductionThe nature of minor element values and impurities are important, both in the assessment of new properties and in the continuing improvement of operating plants. Minor element values often contribute appreciable incremental revenue to a complex base metal deposit. Examples of valuable elements include precious metals, but may also include elements such as indium and bismuth which can be recovered at a profit by smelters provided with the necessary recovery circuits. During preliminary metallurgical studies of a new property there is usually a strong incentive to maximize the recovery of such valuable by-product elements. For example, the extent to which the by-product gold in a porphyry copper deposit is associated with chalcopyrite rather than pyrite may determine theeconomics of developing a new property.The nature of impurity elements in base metal concentrates is correspondingly important in minimizing the penalties which may be imposed by smelters in the treatment of such concentrates. Penalty elements include silica, dolomite (magnesia), arsenic, antimony, mercury, nickel and cobalt. The mineralogical association of these minor elements determines the ability of the mine to remove them in the concentrating process. This paper discusses means of assessing the mineralogical nature of such impurities without the use of sophisticated micro-analytical techniques."

Jan 1, 1997

By Jean-Paul Drolet

"The ultimate aim of the Law of the Sea Conference, held under the auspices of the United Nations, is to ensure that all aspects of the use of the sea are covered by international law. The question facing the nations of the world can be stated as: "" Who will control and benefit from the use and the wealth of the sea?""The United Nations Conference on Law of the Sea - known as UNCLOS - which reconvened in New York during the latter part of August 1978 was the third such Conference in the UN's history. The concepts of sovereignty over the territorial sea and freedom on the high seas have remained fundamental to the international law o f the sea until our time. The legal regime based on these two concepts developed initially from state practice meant that the unilateral actions taken by one or more countries were eventually accepted and followed by others.It was not until 1958, during the first Geneva Conference on the Law of the Sea (pursued in a second Conference in 1960) that the Law of the Sea was codified and modified to a certain extent by the then independent nations of the world in the four multilateral conventions on territorial sea and contiguous zone, continental shelf, high seas, and fishing and conservation of living resources.A third Conference got under way many years later when the members of the UN met in New York at the end of 1973 for preliminary discussions . This meeting stemmed largely from the need to fill gaps in existing international legislation which did not cover the new uses of the sea. The Conference was subsequently reconvened a number of times - in Caracas (1974), in Geneva (1975) and twice in New York (1976) for what was called "" substantive negotiating sessions."" A sixth session was held in New York in 1977; a seventh, held in Geneva at the beginning of 1978, recessed and reconvened in New York at the end of August 1978. This is what is referred to, in international jargon, as the seventh session of the Third United Nations Conference on the Law o f the Sea. The following dates are the principal markers of a saga which began some twenty years ago with the purpose of regulating the use of the oceans."

Jan 1, 1981

By L. Heber Cole

In making this plea for a better and more sympathetic understanding of the non-metallic industry, I do not for one minute wish to give the impression that I in any way belittle the wonderful strides that have been made in the exploitation of our metallics. We in Canada can be justly proud of our Sudburys, Norandas, Flin Fions, and of the remarkable growth of the Consolidated in British Columbia, and at the same time, without in the !east detracting from these worthy undertakings, be equally as proud of our asbestos, gypsum, salt, and coal deposits, as well as of our building-stone and limestone industries. If, in my remarks, I have occasion to compare the metallic with the non-metallic industry, I do so, not with any idea of dimming the glory which the metallics of Canada have gained- not only in our own country, but in the world at large-but for the purpose? of bringing to your attention the fact, perhaps not very well recognized, that Canada contains deposits of non-metallics well worth y of your serious consideration. In the past 33 years, namely, since 1895, the value of non-metallics produced in Canada has exceeded the value of metallics in 19 of the years, and for the last three years has been increasing rapidly. The war years (1915-1918 inclusive) naturally saw an intensive metallic production, but since that time, with the exception of 1925, when there was a general depression throughout the whole country, the non-metallics have been in the ascendency.

Jan 1, 1929

By Alan Reed

"Afton Mines Ltd. (N.P.L.) operates an 8500-tpd open-pit copper-gold mine near Kamloops, R.C. The pit is currently 480 feet deep and will reach an ultimate depth of 800 feet. The east, south and west walls of the pit are composed of Triassic andesites (Nicola Volcanic Formation) and contemporaneous sub-volcanic intrusions of micro-syenite, microdiorite, diorite and picrite-basalt (Iron Mask Pluton). The north wall of the pit consists of Tertiary sandstones, shales and mudstones (Tranquille formation) and dacitic dykes, sills, flows and tuff s (Kamloops Volcanic Formation).The Afton copper-gold orebody (30 million tons of open-pit ore with a grade of 1.0 per cent copper, 0.016 oz/ton gold and 0.12 oz/ton silver) occurs within the Triassic Iron Mask Pluton adjacent to its faulted contact with Tertiary rocks. The Triassic-Tertiary contact is a complex fault system dipping 65 degrees southward and causing the Triassic rocks to overlie the Tertiary rocks. The detailed trace of this contact is very intricate due to the mutual interference of three principal fault systems.The dominant geological structures in both Triassic and Tertiary rocks are faults striking WNW and dipping 65 degrees southward, i.e. sub-parallel to the orebody (strike faults). Cross faults and oblique faults are abundant and highly significant in some sectors of the pit. The Tertiary sedimentary rocks show an early series of northwesterly plunging folds deformed by a later series of northeasterly striking folds. Major lithological and structural boundaries divide the pit into 8 structural domain s within which the pitwall slope stability is controlled by the local geological structures and lithology.Assay data from production blasthole samples and exploration diamond drillhole samples show a log-normal frequency distribution, with a fairly low relative variance. Variograms computed from production blasthole samples show good continuity with elliptical horizontal zones of influence which are truncated by the major faults that bound the ore zone."

Jan 1, 1983

By J. E. Hawley

"The Aldermac copper deposit is in Beauchastel township, Abitibi county, Quebec. It lies about 11 miles west of Noranda. It has been described by Cooke, James, and Mawdsley(2) and by Bruce(3) and has been mapped in detail by W. Samuel and the late K. W. Fritzsche, former Mine Geologist, and by J . E. Gill and A. R. Byers, so that most of the particulars contained in the description that follows are largely the result of the work of others than the writer, whose connection with the deposit, in a consulting capacity, extended over the last 5 years of the life of the mine.According to A. V. Corlett, former Mine Manager, the property was staked during the early winter months of 1923 because of its location adjacent to the syenite intrusive that had been mapped by Cooke near the height-of-land in this township. An examination by Mr. Corlett in 1924 revealed mineralized zones to the north of MacKay lake, and in the vicinity of these K. W. Fritzsche, by dip needle and trenching, discovered the No. 1 and No. 2 deposits, which were both too small and too low grade for exploitation. During the winter of 1925, A. A. MacKay, with a dip needle, picked up a magnetic 'anomaly' in a drift-covered area about 600 feet to the north of previous workings. Trenching here revealed only a narrow zone of mineralization of little consequence, but, farther east, MacKay discovered a more pronounced 'anomaly' over what later drilling and underground work proved to be ore of commercial grade (No. 3 and No. 4 orebodies)."

Jan 1, 1954

When selecting a method for monitoring crack growth in pipeline steel, the sensitivity or crack-size resolution plays a dominant role. Even though there are several visual and non-visual methods, the direct current potential drop (DCPD) method is very effective for monitoring crack growth because of its resolution. This method has been used for the past few decades and has gained increasingly wide acceptance in fracture research as one of the most accurate and efficient methods for monitoring the propagation of cracks. Furthermore, most R&D experience has proven that the electrical potential method can be used in most "aggressive" environments. For these reasons, the DCPD method was selected to design a testing machine to monitor corrosion fatigue crack growth. The use of finite-element modelling is shown to facilitate the application of the DCPD method for monitoring crack growth in steels. The 2D model calibration provided a good description of the test data and proved more accurate than the analytic Johnson's formula.

Jan 1, 2005

By D. R. Pyke

Many of the gold deposits in the Timmins• area show a close spatial association to ultramafic metavolcanics. Available analytical data suggest that ultramafic rocks contain significantly higher gold contents than other major rock types. In addition, recent analyses by Keays (1975) suggest that talc-carbonate alteration of ultramafic rocks releases significant quantities of gold. It is proposed that the ultramafic volcanics formed the principal source of gold for the deposits in Timmins, and that the gold was derived from the ultramafic flows when they were extensively carbonatized. Carbonatization of the ultramafic rocks and emplacement of the auriferous quartz-carbonate veins was probably coincident with the last major period of deformation in the gold camp. Delineation of hitherto unrecognized ultramafic volcanics could be an important guide to the discovery of further gold deposits.

Jan 1, 1976

By J. S. Fox

It is generally recognized that the interpretation of bedrock geochemical data in volcanic terrains can be improved by adjusting for rock-type. Various chemical attributes of volcanic rocks have been put forward in the literature as rapid indicators of rock-type, but there is some question as to which of these is the most reliable . Only one such attribute, total iron, seems to have seen systematic use in geochemical mapping in the Flin Flon region. Discriminant analysis of 500 basalts, andesites, dacites and rhyolites suggests that SiO2 is the most important rock-discriminating variable and that MgO, CaO, TiD2, AI2O3 and FeOtot, are successively poorer discriminators. Lithological normalization in the subalkaline volcanic environment should therefore be made over ranges of this variable. Trace-metal data from drill core through the sulphide orebody at Hanson Lake, Saskatchewan are used to demonstrate various approaches to lithological correction, including silica normalization, factor analysis and trend analysis. All of these extract economically important information from the core that is not apparent in the raw data logs. However, silica normalization does not seem to be subject to as many serious limitations as factor and trend analysis in this case, and therefore seems to provide the most reliable basis for the interpretation of subsurface exploration geochemical data.

Jan 1, 1978

By Maureen Jensen

For mining companies looking to establish a strong North American presence, raise their profile or finance and position themselves for future growth, there is no other destination in the world that can offer a mining company the same opportunities as Canada whether you are an established blue chip or promising junior. Despite historically poor world commodity markets and shaky investor sentiment towards junior explorers caused in part by fallout from the high profile Bre-X fraud, Canada continues to shine as the undisputed mining finance capital of the world. Our natural riches and mining history go a long way to explain Canada's international prominence in mining finance. Canada has actively created and maintained one of the most integrated national frameworks to support mining ventures of all kinds. Our diverse industry, from one-person grass-roots explorers to mining industry giants, is one of our main strengths whether your company is Canada-focused or internationally active. The mining industry continues to be a vital contributor to the Canadian economy, contributing $26.2 billion in 1997 or 3.8% of national GDP, and is the second largest earner of foreign exchange. Industrial mineral companies are a very important part of this strength. These companies require a continuing access to capital to ensure that they can continue to compete and the globalisation of the Canadian mining industry has affected this industry just as much as it has affected every other industry in Canada.

Jan 1, 2001

By Mikael Ramström

The IREDES Special Interest Group (SIG) for Drill rigs has been active since its inception at MineExpo 2000, in Las Vegas USA. The SIG for drill rigs is responsible for the development of a IREDES Drill rig profile. This includes the exchange of production planning, performance and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During year 2001 a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies and third party suppliers and reviewed during several SIG meetings. In mid 2002 the profile was released for prototyping projects and since then, feed back received from these projects has been used as input to the first official IREDES release. LKAB and Atlas Copco decided in 2002 to start an IREDES prototyping project using the Simba L6C production drill rig as target equipment. The goal was to verify the drill rig profile and identify possible problems prior to the official release. This was done by implementing the IREDES prototype version in the LKAB?s production planning system and Simba rig control system. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this the mine production system was adapted for drill plan export and logging data import on IREDES format. This paper presents the most recent results of this prototyping project. Result from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES will be a central issue for future mine automation. As a result from this and other IREDES prototyping projects the official IREDES release will be available in 2003. Soon after that release IREDES compliant products can be expected. This will include drill rigs and mine production planning systems.

May 1, 2003

By James A. Finch, Yue Hua Tan, Wei Zhang

"The paper is part of our study of the frother structure-property relationship using bubble rise velocity. Single bubble rise velocity profiles were determined in a 350 cm column for surfactants from the polypropylene glycol (PPG) family. Using velocity at 300 cm, the concentration to reach minimum velocity (CMV) is determined. The CMV is shown to decrease as alkyl chain length (n, number of carbons) increases and as the number of propylene oxide groups (m) increases. Linear correlations log CMV vs. n and m were observed. Taking literature data for critical coalescence concentration (CCC), linear log CMV vs. log CCC correlations were also noted. Mechanisms are briefly discussed, and prediction of CCC made for a commercial polypropylene glycol.INTRODUCTIONAs one of the great enabling technologies of the 20th century, froth flotation is a highly versatile method for physically separating minerals by exploiting differences in wettability (hydrophobicity). Over the last century, flotation reagents have undergone significant developments (Khoshdast and Sam, 2011). One important group of reagents is frothers which are used to reduce bubble size, slow bubble rise velocity and help stabilize froth (Klimpel and Isherwood, 1991).Frothers, originally derived from natural sources (e.g., pine oil and cresylic acid), are largely replaced today by synthetic products which provide more consistent properties. Polyglycols, based on PEO (polyethylene oxide), PPO (polypropylene oxide), or PBO (polybutylene oxide) groups, were first described by Leja and Nixon (1957) and have attracted wide use since then (Farrokhpay 2011). The chemical structure of polyglycols can be represented by a general formula: R(X)mOH, where R = H, or CnH2n+1 and X stands for EO (-C2H4O-), PO (-C3H6O-), or BO (-C4H8O-). The polypropylene glycol ethers (CnH2n+1(PO)mOH) are the most common of these reagents (Pugh, 2007) and the focus of this study.In general, the chemical structure of frother molecules comprises two parts, a non-polar hydrophobic hydrocarbon (alkyl: CnH2n+1) chain and a polar hydrophilic head. By introducing the ether -Olinkage, which acts as another polar site, the propoxy group (-OC3H6-) in the structure makes the frother readily soluble in water (Somasundaran and Wang, 2006), facilitating the industrial use of these frothers. Available as by-products, Dow Chemicals introduced as series of polyglycols, e.g., Dowfroth (DF) 200, 250, 263, and 1012, the most familiar being DF250 (CH3(PO)4OH), a polypropylene glycol methyl ether. While no longer available from Dow, these and other polyglycols are still widely used."

Jan 1, 2016

By J. E. McMenamin, R. B. Hall

"With the emphasis in the past decade on larger and more efficient equipment for open-pit operations, the Normandie mine of the Asbestos Corporation has followed the trend, switching from the smaller type of percussion drills to down-the-hole rigs. One 5 Y2 -in. percussion drill is still in use, but is limited to a ""smooth blasting"" role or to the control of the slope on final benches.In keeping with the times, an attempt was made to eliminate, as much as possible, the use of high explosives and to maximize the percentage of ammonium nitrate -fuel oil mixture. As the concentration of ground water increased with increased mining depths, small pumps were initially employed for the dewatering of boreholes. This proved unsuccessful, and a hole-blowing rig was built and a conversion to plastic liners made. The acquisition of a bulk-mix AN-FO truck has permitted the changeover from an AN premix to an ammonium nitrate prill -fuel oil combination at the borehole."

Jan 1, 1966

By M. Jiang, X. Fan, W. X. Chen, Z. K. Guo, H. H. Zou

"Some improvements are carried out for elasto-plastic model by taking the shear dilation effects and relaxation effects of deep rocks into accounted. The high pressure equations of states with Mie-Grüneisen form are also introduced to describe the relation of pressure-volumetric strain. Numerical simulations of free field responses for deep underground explosions are conducted by using the user subroutines which compiled by means of the secondary development functions of LS-DYNA9703D codes. It is indicated that the dynamic responses of free field are well simulated based on this improved elasto-plastic model, and the analytical results are in good agreement with the data of U.S. Hardhat nuclear test.INTRODUCTIONDynamic behaviors of deep rocks for underground explosions are obviously different from that of shallow underground explosions and have aroused great attentions of international experts who work for rock engineering. The dynamic models of deep rocks could be roughly divided into classic elasto-plastic model and fracture damage model according to different theoretical foundation. M. E.Kipp and D. E.Grady et al. are the outstanding representatives who engaged in the researches of fracture damage mechanics. Researches of dynamic problems for geomaterials were carried out by C.C.Grigorian and the conclusion that incompressible elasto-plastic medium model could not be used to solve the problems of closed underground explosion was derived, and therefore C.C.Grigorian model was proposed. In this model, C.C.Grigorian assumed that the average hydrostatic pressures and the densities of medium had one to one relationship, and the path of loading or unloading is different from each other. For shear deformations, analytical solutions of the problems were derived according to the model which was slightly different from Prandtl-Reuss model, the constitutive equations were closed by Mises-Schleiher constitutive model. However, the analysis showed that there were two inadequacies in C.C.Grigorian model. Firstly, the shear dilation effects of fractured medium after wave front could not be considered. Secondly, the relaxation characteristics of the rocks in fractured region were not taken into account."

Jan 1, 2015

By S. Shairp

At the Hudbay zinc pressure leach plant, filtration and washing of the second stage leach slurry takes place on a vacuum belt filter prior to disposal to tailings. Due to periods of poor filterability, laboratory studies were undertaken to investigate the effect of temperature of the filter feed slurry, and to compare filterability to the resulting cake particle size distribution.

Jan 1, 2014

By R. Edinger

Aerospace and space products depend, probably more than any other products in industry, on advanced materials. While there are many ways of producing aerospace parts, in many cases the process does not allow the design of the metallurgical properties according to the part or product requirements in accordance with its mechanical configuration. Key to the next level of innovative manufacturing is the capability to control the amount of energy applied to the process, as well as the addition of materials in form of vapor or solid particles such as powder in order to build up the metallurgical composition required. With the development of a high speed pulsed laser-electron beam source, the LASTRON(TM) technology, we deliver the basic requirement for a digital manufacturing process of aerospace and space products. This technology, combining Laser and electron beam, finds application in welding, drilling-machining, and is currently modified to allow digital coating (PEB-PVD) methods. In addition to the coating, a powder metallurgical process, called Rapid Manufacturing (RM), will allow the precision melting of parts based on CAD/CAM files. The RM process and the digital coating will allow the production of graded aerospace alloys in parts for jet engines and aero-structures.

Jan 1, 2006

By J. Peck, F. Brackebusch, M. Scobie

"A number of alternative strategies exist to improve narrow orebody stope productivity and safety through mechanization. Particular attention is given to one of these: the development of an in-stope mining machine. This paper summarizes those characteristics of vein orebodies in Canadian mines which are considered to govern such mining machine design. It then reviews past and current attempts to develop hardrock mining machines which could potentially be applicable to narrow stope widths.IntroductionSerious interest is mounting to exploit new technology in the development of methods and machinery to stope narrow, hardrock, orebodies. The motives relate not only to the foreseen need to maintain or reduce production costs, but also to considerations of manpower availability, safety, ground control, ore recovery and dilution. This also follows the demonstrated success of technology application in larger metal orebody stoping, where machine development has been seen to lead to improved productivity as well as the future prospects of continuous mining systems and eventual automation, e.g. ITH blasthole drill development and bulk mining. This paper deals in particular with machine design for ore fragmentation in narrow, hardrock orebodies. It is considered that such machine design closely interacts with the over-all stoping method design and that both require consideration in parallel to ensure success in mechanization."

Jan 1, 1990

By Karina Forster

Open stope design depends on the ore body geometry, loading conditions and rock mass properties to estimate stope dilution and ground support requirements. Rock mass conditions for design primarily rely upon estimates of well established rock classification systems. Many sources of data exist for obtaining estimates for these rock mass classification values which include core logging, geotechnical mapping, geological mapping as well as linking one classification system to another through the use of empirically derived equations. The extent of mapping coverage can also vary significantly based on the data collection technique. This paper proposes an approach where individual components of rock mass classification systems are collected by the different available data collection techniques. Data from different rock types are also considered separately based on their alteration characteristics and general observation products. Data from the Cameco Corporation Eagle Point Mine is presented and an approach is outlined for obtaining average representative classification values for stope hanging wall characterization. The effectiveness of this approach is demonstrated through the analysis of a data base of hanging wall dilution information.

Jun 1, 2012