Search Documents

By G. A. Fenton, A. Vervoort, M. Alvarez Grima

"High-risk underwater mining operations necessitate characterizing spatial heterogeneity and resource uncertainty. Local average subdivision is a method of simulating spatial deposit variability inside a cell through a sequence of discretization stages, during which a cell is further subdivided into four or eight cells. New developments are presented to validate simulated deposit models and deal with point measurements of geotechnical and ore-grade properties. This paper illustrates the relevance of translating spatial deposit variability into financial or operational performance indicators during underwater resource exploitation. Two synthetic case studies highlight the challenges of underwater mining in relation to production plans and equipment selection.RÉSUMÉ Les opérations d’extraction minière subaquatique à risque élevé exigent une caractérisation de l’hétérogénéité spatiale et de l’incertitude de la ressource. La moyenne locale de subdivision est une méthode de simuler la variabilité spatiale du gisement dans une cellule par une séquence d’étapes de discrétisation durant lesquelles une cellule est subdivisée en quatre ou huit cellules. De nouveaux développements sont présentés afin de valider les modèles de simulation des gisements et de traiter des mesures ponctuelles des propriétés géotechniques et de teneur du minerai. Le présent article illustre la pertinence de traduire la variabilité spatiale du gisement en indicateurs de rendement financier ou opérationnel durant l’exploitation subaquatique de la ressource. Deux cas synthétiques soulignent les défis de l’exploitation minière subaquatique par rapport aux plans de production et de choix des équipements."

Jan 1, 2015

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Spring-Back/Forward in sheet metals is defined as recovery of elastic strain upon unloading in a deformed sheet specimen. Since this phenomenon can cause alternation in the dimensions of a part, leading to irrecoverable compensations, the operative parameters need to be investigated, thoroughly. To assess spring-forward and effective bending parameters, V-shaped bending dies are the most commonly used experimental approach. In the present research, the effect of bending angle and punch tip radius on the spring-forward behavior of an Al-Mg-Si alloy sheet specimen is studied. To this end, a V-shaped die with four bending angles (i.e. 30°, 45°, 60°, and 90°) was designed and fabricated. Specimens with thickness of 2 mm were cut with dimensions of 50 mm×10 mm. Results show that by increasing the bending angle, the spring-forward angle decreases. In addition, smaller punch tip radiuses lead to further spring-forward. The effect of these parameters on the amount of spring-forward angle, strain distribution and homogeneity along sheet thickness was assessed using finite element analysis (FEA). Simulation results show that as the bending angle increases, the strain is developed more homogenously. Finally, micro-hardness test was used to study the effect of strain hardening caused by bending operation on strength evolution. Results show higher hardness trends for the zones in which the maximum plastic strain occurs.INTRODUCTIONPrecise production plays a significant role in the durability of a part. When it comes to sheet metal forming, this issue should be taken into account as an important factor. In order to predict the alternations, bending dies with special geometric parameters (i.e. V-shaped, U-shaped and L-shaped dies) are commonly used (Wagoner, Lim, & Lee, 2013)."

Jan 1, 2016

By Daniel Hodouin, Mélanie Proulx, Claude Bazin

"Collector and frother are commonly used to induce the floatability of valuable minerals in flotation plants. These reagents are usually distributed down a flotation bank or sometimes added in a single location at the top of the bank. A review of the literature and some experimental results obtained from laboratory and full scale trials indicate that the way flotation reagents are distributed down a flotation bank may influence the flotation response of coarse particles. The paper summarizes these observations which show that the distribution of reagents is a potential tuning variable for process optimization.IntroductionFlotation is in many cases the only way to concentrate sulphide and some oxide minerals. Flotation is a concentration process that uses particle surface composition to induce the selectivity by mean of hydrophobic reagents. The influence of particle size on flotation was firstly analyzed in the 50's1·2 and intensively investigated in the 70's, early 80's and 90's3-18. Most of the observed results show the existence of an optimum flotation size range9 whose recovery is not significantly influenced by a reduction of collector dosage""18. This result brought the idea of using a small portion of the total collector dosage at the top of a rougher bank and to distribute the remaining through the end of the bank to ensure sufficient collection of the coarse particles that need more hydrophobic coverage to attach to air bubbles and be lifted to the surface.This paper discusses the idea of using the distribution of reagents down a flotation bank to tune the operation of the process. Unlike the literature on the effect of reagents (collectors, frother...) dosage that is dense, little attention has been put on the distribution of reagents in a flotation bank. Although research on this subject has not been pushed very far, some operators have recognized the potential of a strategic addition of reagents down a flotation bank19. Except for a few exceptions, the proportions of the reagents to be distributed down a flotation bank are decided according to operator's experience instead of process analysis in relationships with particle size. This paper recalls observations made by different researchers that lead to the idea of using the distribution of reagents as a tuning variable for the flotation process. The paper does not present a detailed analysis or optimization scheme for tuning the distribution of reagents, but analyzes some plant and laboratory results with a view toward the development of a testing methodology and ultimately a validation or rejection of the idea."

Jan 1, 1998

By S. Makni, S. Koppalkar, A. Bouajila

ABSTRACT This paper briefly reviews the gravity recovery between conventional and centrifugal gravity separators. The advantages of semicontinuous gravity separators will be discussed, as will techniques for upgrading the gravity concentrates. The research efforts in optimizing semicontinuous gravity separators will be recalled. An innovative gravity circuit for eliminating or minimizing the use of complex processing schemes will be reviewed. Ongoing gold gravity research has revealed that gold particle shape transformation is one of the main factors explaining the lower recoveries of the plant units. Efforts to devise possible remedies for improving plant gravity recovery will be discussed.

Jan 1, 2013

By N. Bédard

"This paper highlights Cambior’s initial approach for recruiting and retaining its international employees, the importance of proper preparation and the support needed to ensure a competent and stable workforce.In general, most of the training and information available for human resources personnel prepares the specialist for handling various aspects of labour relations, recruitment and hiring, benefits administration, employee relocation, etc. This is usually done in a Canadian context.Only recently, has more specialized training been developed to prepare human resources practitioners for the complex issues related to expatriate employees and dealing with human resources issues in other countries"

Jan 1, 2004

By D. S. Evans

Major Project Blues Over the last two decades, almost every major project has suffered significant cost overruns, significant schedule delays, and/or poor quality work. Exceptions are rare and most projects that tout being ?On Time and Under Budget? have re-cast schedules, significantly modified scope or revised base estimates. The problem isn?t new. In the late 1980?s the Rand Corporation published a study showing that 80% of all major projects had significant cost and schedule overruns. The problem is not restricted to the Canadian environment, or to a specific industry. It is a global problem.

May 1, 2013

By K. Miao, W. Mu, M. Sharma, A. Haas, N. Dogan

"The ever increasing demand for cleaner steels with low inclusion content has highlighted the limits of our current knowledge for controlling and predicting inclusion agglomeration and removal during liquid steel processing. Key knowledge gaps in this area result from the complex nature of the problems associated with measuring and visualizing the phenomena studied. Confocal scanning laser microscope (CSLM) allows for continuous in situ observation of micron-size samples in real time, at high resolution, under conditions relevant to the steelmaking process. This paper summarizes some of recent CSLM applications in our laboratory to illustrate the methods of analyzing transient behavior. The reaction between inclusions and slag is given as an example. The dissolution rate of calcium aluminate inclusions in CaO-SiO2-Al2O3 slags has been studied at elevated temperatures: 1500, 1550 and 1600°C as well as thermodynamic/kinetic analysis. It is found that total dissolution time decreased with increasing temperature. The rate limiting steps are discussed. It is shown that the diffusion through a product layer is responsible for dissolution at 1500°C. At higher temperature, dissolution is most likely controlled by both boundary layer diffusion and chemical reaction at the slag-inclusion interface. In this paper, the evidence for and against the theory will be critically examined and repercussions of the theory to steel refining processes will be discussed.INTRODUCTION Inclusion formation during liquid steel refining is an unavoidable consequence of current ladle steelmaking processes. The nature and quantity of the inclusions formed in steel is critical in steelmaking, as it affects both productivity through clogging, and downstream physical properties of the steel. It is therefore crucial to better understand and control the formation, agglomeration and dissolution behaviour of inclusions in a slag in order to improve the removability of inclusions from liquid steel. Most research (Sandhage & Yurek, 1988; Sandhage & Yurek, 1990a; Sandhuge & Yurek, 1990b; Sandhuge, 1991) relevant to the kinetics of inclusion removal has been obtained by using a technique where simulated inclusion material (ceramic rods) is dipped in slag and the dissolution rate is measured. While much has been learned using this approach, the difference in scale from bulk materials to inclusions is likely to have a significant bearing on the dissolution kinetics of inclusions in a slag and will certainly result in a very different influence of capillary effects. Further, the data obtained using an indirect (dip test) procedure relies on a comparison of the initial and final conditions of a sample rather than in-situ observation which can be achieved in a confocal microscope in real time."

Jan 1, 2017

By L. Bichler

Utilizing thermal analysis techniques, pioneering research into the solidification mechanism of a popular magnesium alloy AZ91E cast by the Lost Foam Casting (LFC) process was carried out, Foam characteristics, section thickness and application of vacuum were seen to have profound effect on the cooling rate, thermal gradients and casting temperature profiles.

Jan 1, 2005

By H. J. Conolly

The area around Osisko lake, the Horne mine, and the town of Rouyn, in northwestern Quebec, presents a most interesting structural problem. The present discussion is confined to an area around Osisko lake, about six miles long and three miles wide, shown in Figure 1. The writers are particularly indebted to Mr. Thayer Lindsley, of Ventures Limited, who sponsored the investigation and gave permission to publish this paper. Mr. H. L. Roscoe and Mr. Oliver Hall, of Noranda Mines, Limited, gave every possible assistance; and the Noranda geologists, Mr. H. M. Butterfield, Dr. Peter Priee, and Dr. G. G. Suffel, contributed many data and ideas. It is a pleasure to acknowledge also the fuidance of Dr. W. F. James and Dr. B. S. Buffam and the full use made o their maps and criticism. Dr. M. E. Wilson and Dr. A. Lang, of the Geological Survey of Canada, kindly furnished data on the geology in neighbouring fields. Mr. E. Bailey assisted ably in the field, and Mr. H. F. King kindly reviewed the text. Memoir 166 of the Geological Survey of Canada, The Geology and Ore Deposits of the Roztyn-Harricanaw Region, Quebec, by Cooke, James, and Mawdsley, proved an invaluable source of information. STRATIGRAPHY The following stratigraphie sequence is based in part upon the interpretation of the structure as outlined in this paper:

Jan 1, 1936

By Charles S. Ney

"THE WRITER'S acquaintance with Kootenay King mine is limited to a brief geological excursion in the vicinity. This paper has been compiled largely from maps of J. Sullivan, mine geologist in 1952, kindly made available to the writer by Transcontinental Resources; a 1942 private report by W. L. Brown; and personal communications with J. Sullivan. Remarks on regional geology, and the comparison with Sullivan mine, are specifically the writer's.The Kootenay King mine is situated in the westernmost range of the southern Canadian Rockies at an elevation of 7,300 feet. From the Sullivan Mine at Kimberley, B. C., it lies 19 miles due east. Six miles of this distance are represented by the pronounced topographical and structural gap of the Rocky Mountain Trench. Mineral claims were locat-ed in the area prior to 1898. The deposit was first seriously explored in the late 1920s, and a small orebody was then outlined and developed. Mining and milling were undertaken in 1951.52. The orebody, amounting to about 14,000 tons, was mined out, and no significant new ore was revealed.The orebody is a replacement of dolomitic argillite by fine-grained galena, sphalerite, and pyrite. The sulphides are finely laminated in the direction of bedding, following out minor folds faithfully. The grade of ore estimated from diamond drill holes (W. L. Brown, 1942) was 11 ·I per cent zinc, 11 ·I per cent lead, and 3·8 ounces per ton of silver. The mineralized zone extends about 250 feet horizontally, 160 feet vertically, with a width of six to twenty feet.General GeologyThe country rocks are sediments of the Aldridge formation of late Precambrian age. For several thousand feet stratigraphically above and below the mine, the formation consists mainly of thinly laminated argillite and siltstone. Several horizons contain appreciable carbonate. About 2,800 feet stratigraphically below the mine, predominantly dolomitic beds mark the top of the underlying Fort Steele formation. The medium-bedded fine quartzites, which characterize about 10,000 feet of the Middle Aldridge in the Purcell range, have a restricted development amounting to only 2,000 feet in the Rocky Mountains. This member is about 2,200 feet above the mine horizon."

Jan 1, 1949

By M. H. Cullender

THE determination of the flow characteristics of gas wells depends upon the analysis of pressure data obtained under shut-in conditions and under one or more known flow conditions. These data are commonly referred to as back-pres-sure test data, and I know you are all familiar with the back-pressure equation where, Q rate of flow, Mcfd @ standard conditions C coefficient of the back-pres-sure curve P 1 formation pressure, psia P • sand face flowing pressure, psia P2 (psia)2/1000 n exponent of the back-pres-sure curve Figure 1 is a graphical presentation of the back-pressure equation; the coefficient is the rate of flow at a difference in squared pressures of 1, in this case 2250 Mcfd, and the exponent defines the manner in which the rate of flow changes with a change in the difference in squared pressures. In Figure 1, the exponent of the back-pressure curve is 0.554 which means that for a 10-fold change in the difference in squared pressures, there will be a 3.58-fold (10 raised to the 0.554 power) change in the rate of flow.

Jan 1, 1961

By B. I. Boyko

As part of the Ministry of the Environment's Resource Recovery Program, the Province of Ontario has constructed a $13 million "Experimental Plant for Resource Recovery" in Metropolitan Toronto. The technology and unit operations involved in the processing of municipal solid wastes at a rate of 40 tons per hour at this facility are reviewed. Shredding, air separation and classification, screening, magnetic separation and composting are some of the operations featured at this plant. Recoverable commodities expected include paper, ferrous metals, an air-classified light fraction (shredded paper and film plastic), glass and compost. Existing and potential markets for these materials are discussed.

Jan 1, 1978

By I. M. Masters

Iron removal and control in processes employing pressure leaching technologies developed at Dynatec Corporation are reviewed. Discussions are focused on recent developments in the processing of nickel-copper matte and copper concentrates, and on the Ambatovy laterite project in Madagascar. Iron control and its implications on flowsheet design in the pressure acid leaching (PAL) treatment of laterite ores and in the oxidative pressure leaching of mixed nickel-cobalt sulphide intermediates are also discussed.

Jan 1, 2006

By J. Drenda

The model for methane removal from the workings directly behind an advancing longwall as presented in this paper may be used for U-ventilated cross or length-wise systems of longwall advance, starting from the boundaries of the extraction field. In mines with high methane concentrations, Uventilated longwall extraction from the boundary of the extraction field produces a methane risk. The risk is manifested by a higher methane concentration at the end of the longwall, upper gate and incline. The methane in increasing concentrations, which is emitted mainly from the workings with caved areas, appears towards the end of the longwall and in the upper gate. The graphical model of the longwall provided includes both the workspace of the longwall and the caved area. Based upon a model of the rock distribution in the cave, a ventilation model comprising two standard air splits and large number of crosswise air splits has been constructed. Simulations indicate that if the shearer is not present in the longwall, the air distribution in the caved area is symmetrical. The presence of the shearer, both at the bottom and the top of the longwall, causes an asymmetrical air distribution in the cave, that is the asymmetrical flows in the goaf and longwall workspace and in the inflows and outflow between those regions. This phenomenon causes an increase in methane concentration at the end of the wall and at the upper gate. The methane removal method proposed for workings with a caved area directly behind the advancing U-ventilated longwall, starting from the boundary of the field, consists of the removal of methane-air mixtures from the caved area with the boom pipes. These booms may be of several meters long and may be extended if necessary. The insertion of the boom pipes into the cave towards the end of the longwall and connecting them with the general methane removal system creates negative pressure causing a change in the depression field, which is the aerodynamic potential field in the goaf area around the ends of the boom pipes. This will promote the extraction of the methane-air mixture from voids and the goaf cracks, and the area from which methane is being extracted may extend to the side of the cave. This is a positive phenomenon, which could result in the methane flow from the goaf into the airflow in the longwall workspace decreasing or even stopping. A reduction in the methane flow into the longwall workspace with extractions booms will be advantageous for the production continuity. Based on the floor load model for the rocks in the cave and the methane-removal boom load model, the value of the force required to move the boom behind the advancing wall has been calculated. Strength calculations for the pipe were performed using a finite elements method. The analysis results, as well as the comparison of the pipe material effort to the strength parameters of steel, which can serve as piping material (for the assumed load conditions), lead to a belief that the proposed boom construction satisfies the strength requirements.

Aug 1, 2013

By S. Spigarelli

The creep response of the AE44 magnesium alloy was studied by means of constant load creep tests carried out at 125 and 150°C, obtaining that at the latter temperature the minimum creep rate observed under an applied stress of 100 MPa was two orders of magnitude lower in the investigated alloy than in AM50. The minimum creep rate dependence on applied stress was described by a conventional power-law, e = Aon , where A was a temperature dependent parameter and n was the stress exponent, resulting in a n value close to 30, i.e. by far larger than those observed in commercial alloys with similar Al content. This large difference in creep response was attributed to the precipitation of rare earths (RE) intermetallic phases distributed in the grain boundary zone in form of an almost continuous network of dispersoids that were observed by means of scanning electron microscopy.

Jan 1, 2006

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

By I. Caraconcea, M. Cousineau, S. Gariepy

"Several base metal plants operate in low grade/high tonnage conditions which impose strict cost control on all fronts for their operations to remain profitable. This leads to decisions regarding plant design, procurement, operations and maintenance that often favor cost minimization over value optimization. This may hinder the representativeness of the metal accounting systems while this should be a priority in a low margin environment. Such poor representativeness not only creates confusion in plant scheduling but can also hide suboptimal metallurgical performance. Furthermore, this situation can run undetected for a while since one dominant feature of a poor metal accounting system is its poor self-awareness. During their practice, authors have particularly identified measurement bias and reproducibility, as well as their impact on metal recoveries as areas of concern. These issues have not been extensively reviewed in the specific context of precious metals in base metal plants. Pragmatic solutions are proposed either at the design stage for a new project or to retrofit an actual operation. These solutions should be based on a business analysis that set a value of information matching the contribution of precious metals as well as the potential to use such information to act toward increasing plant profitability. Conclusions are that trade-offs are an inherent part of the design/audit/retrofit of any metal accounting system in any plant processing either base or precious metals. However, compromises must be evaluated on economic/technical ground.INTRODUCTION Every mineral processing plant must produce metal accounting reports (Morrison, 2008) where estimated saleable metal flows and inventories are published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimization, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that state of the art metal accounting is instrumental for mining companies to reach and sustain high-quality corporate governance (Gaylard, Randolph, & Wortley, 2014). However, producing a metal accounting report involves much more than just printing it (Lachance, Leroux, & Gariépy, 2015a). The underlying metal accounting system (Figure 1) is responsible not only for the reliable production of the metal accounting reports but also for the quality of the outcome. As such, the crucial tasks of its design/audit/retrofit should neither be seen as ancillary nor be left as an afterthought."

Jan 1, 2017

By D. C. Fraser

"Geophysical Engineering and Surveys Limited of the Keevil Mining Group have routinely conducted ground surveys with VLF-EM receivers for the past two years. Both Crone's Radem and Ronka's EM16 have been used.VLF-EM dip-angle data often yield complex patterns which require considerable study for a proper interpretation. A method was developed which allows field operators to transform the noncontourable dip angles into contourable data, producing conductor patterns which are immediately apparent to exploration personnel untrained in VLF-EM interpretation.VLF-EM contoured data generally peak very close to the top of a conductor, thereby allowing drill holes to be spotted accurately. However, the data generally should not be used alone to select drill targets because structures may be sufficiently conductive to yield strong anomalies. Thus, magnetic and/or vertical-loop EM correlations may be considered as necessary criteria for drilling.VLF-EM surveys can replace IP surveys in certain environments. For example, the Restigouche orebody in the Bathurst camp of New Brunswick yielded a VLF-EM anomaly as distinct as that obtained by IP, although the body did not respond to vertical-or horizontal-loop EM. However, the cupriferous breccia pipes of the Triba mine near Batchawana, Ontario yield strong IP anomalies but not VLF-EM anomalies, illustrating that disseminated ore targets should be sought with IP rather than with VLF-EM."

Jan 1, 1971

By George H. Bodfish

This paper begins with a short history of air compressors, emphasizing their "roots" in the mining industry. It then describes the types of compressors available, including reciprocal, the various rotary positive-displacement compressors, and the centrifugal. The advantages and disadvantages of selecting a certain type of compressor over another are enumerated, considering customer requirements and operating costs, among other factors. Guidelines to operation and maintenance are discussed, including installation, monitoring and maintenance procedures. Finally, the paper addresses itself to future trends, with special attention being given to the system concept, the increasing use of rotary compressors, power consumption, reliability, packaging and noise attenuation.

Jan 1, 1978

By A. J. Rigby

Anode vessels are often relined with refractory every one to two years and a typical reline time can take between 16-20 days. Modem refractory designs using dense, corrosion resistant brick applied directly to the vessel shell in the high wear areas around and above the tuyeres and at the slagline can yield a lining life of up to 4-5 years before a complete reline is necessary. Installation methods using brick delivery on roller conveyors through an endwall access port and complete anchoring of the brick to allow for lining self-support can take days off the installation time. It is possible, therefore, to reduce the refractory relining period by 50% and increase lining life by 100% compared to typical anode repair schemes. Cu2007

Jan 1, 2007