Search Documents

By C. R. Larsen, R. G. Bradburn, A. L. Mular, B. C. Flintoff

"Following the acquisition of grinding- circuit data at Brenda Mines Limited for simulation purposes, various methods to mass balance the circuit were evaluated. Unfortunately, different answers were obtained for different balancing methods. A data-adjustment procedure was therefore developed. The procedure assumes that all ""best-fit"" criterion. A search is conducted with the minimum set of water masses and narrow size ranges of solids around the circuit (called search variables), which permit the computation of any of the measured data points. Search variables are used to calculate measured values for an objective function of the form: [ ] where W, is a weighting factor•, M1 is a measured value and M. is a corresponding . value calculated from search vanables. The best values of M, are those which minimize R. The above method is compared with others that have been utilized for mass balancing circuits."

Jan 1, 1976

By F. W. Tregarthen

"This paper gives a brief description of the methods used to form and implement the present planned maintenance program. The system is designed to assist plant personnel in their task of controlling a large work-force and maintaining the many and varied types of equipment used in a mining and concentrator operation. The types of reports and methods used in scheduling and work-loading are described. General built-in flexibility is derived from computer assistance to the Central Planning Group."

Jan 1, 1971

By D. Vanin

"Conventional single heading track drifting in the hard rock mining industry has not shown any significant improvements in advance rates, despite the advent of modern track jumbos and igh speed muck handling systems .This paper presents Kiena 's experience in using a 7 ft 2 in. diameter larva Mark 6 Tunnel-Boring Machine (TBM) for driving 6000ft of drift.IntroductionKiena Gold Mines is located about 5 miles west of the town of Val d'Or, Quebec, approximately 300 miles north of Montreal. The mine commenced production in October 1981 and has gone through various expansions of ore production with 287 916 metric tonnes in 1982 to reach 453 800 metric tonnes in 1986.Due to the majority of claims being covered by a lake, a grassroots exploration drive of remote areas of the property was required to allow diamond drilling on a yearly basis. High speed sequential excavation methods (SEM) of single heading drifting in the mining industry has not progressed much in the past 20 years despite the advent of electric-hydraulic jumbos, Haggloader and Hagglund type cars. Certain examples of record SEM drifting advances have been performed in the past but only under very specific ground and cost conditions."

Jan 1, 1987

By J. S. Stacbulak

"The main ventilation design features adopted at Inco to safeguard personnel against the effects of fires are described in this paper. Measures taken to prevent and detect fires due to spontaneous combustion, and fires involving conveyor belts, are described in detail.IntroductionConsidering the over-all picture of present-day mining operations, the expenditure required to provide a proper system of mine ventilation and fife control should be regarded as a sound investment that will pay back in increased mining efficiency, improved safety, health, and morale of the miners.Mine ventilation control and mine fife detection and fighting are inseparable, because a ventilation system can spread deadly products of combustion just as efficiently as it does life-sustaining oxygen. Therefore, the possibility of a mine fife occurring is of particular concern.The flirt objective is to prevent a fife. The second objective is to design the ventilation system so that a positive fresh air supply can be ensured on each main level regardless of the location of the fife. The third objective is to be able to detect the fife at an early stage and to extinguish it before it can develop into a major fife.Accordingly, at Inco, very extensive measures are taken to prevent fires and to locate, isolate and extinguish them rapidly. To obtain an early warning, it is not sufficient to know that a fife has started, but it is also necessary to know where the fife is burning."

Jan 1, 1994

By J. S. Stachulak

"The main ventilation design features adopted at Inco to safeguard personnel against the effects of fires are described in this paper. Measures taken to prevent and detect fires due to spontaneous combustion, and fires involving conveyor belts, are described in detail.IntroductionConsidering the over-all picture of present-day mining operations, the expenditure required to provide a proper system of mine ventilation and fife control should be regarded as a sound investment that will pay back in increased mining efficiency, improved safety, health, and morale of the miners.Mine ventilation control and mine fife detection and fighting are inseparable, because a ventilation system can spread deadly products of combustion just as efficiently as it does life-sustaining oxygen. Therefore, the possibility of a mine fife occurring is of particular concern.The first objective is to prevent a fife.The second objective is to design the ventilation system so that a positive fresh air supply can be ensured on each main level regardless of the location of the fife.The third objective is to be able to detect the fife at an early stage and to extinguish it before it can develop into a major fife. Accordingly, at Inco, very extensive measures are taken to prevent fires and to locate, isolate and extinguish them rapidly. To obtain an early warning, it is not sufficient to know that a fife has started, but it is also necessary to know where the fife is burning."

Jan 1, 1994

By N. Novikov, M. Jastrzebski, N. Kryzhanovskaya, D. Shevchenko, I. Kapran, N. V. Novikov, T. Koehler, B. Zaporozhets

"The PFK FeNi Smelter was re-commissioned by Solway Resources in 2002, ending a long period of economic decline in the adjacent town. In 2009 Hatch was retained to design, supply and install a custom furnace crucible that would accommodate a capacity increase from 34 MW to 40 MW and increase campaign life through binding and cooling technologies, as part of ongoing improvement efforts. The involvement of PFK personnel was critical to the successful integration of the new furnace technology with the existing process and operational practice. The furnace upgrade project was completed in 18 months during 2010 – 2011. Since start-up, the furnace has exceeded production expectations, operating successfully at 42 MW.INTRODUCTIONAfter ceasing operations in the 1990’s, the Pobuzhsky Ferronickel Combine (PFK), located in central Ukraine, was stripped of useful equipment and deteriorated while dormant. The surrounding town experienced a period of economic decline throughout the 1990’s. Solway Industries purchased the complex in 2002 and began a systematic incremental program to re-commission the smelter using both local expertise and specialists from other parts of the former Soviet Union. This led to the re-birth of PFK as a successful toll-smelting complex, and a renaissance for the surrounding economy.As part of the continuing improvement program, PFK approached Hatch in 2009 to study the possibility of a capacity expansion from 34 MW to 40 MW. It was decided, based on the results of the study, to design and install a custom furnace crucible integrating the unique PFK FeNi process with modern Hatch furnace technology. This novel approach had many benefits, including: maximum re-use of existing furnace components (off-gas, feed equipment and transformers), minimal impact on upstream and downstream equipment and building structure, and the retention of a familiar operating regime. The latter was a key factor in the success of the project, as it allowed the extensive operating expertise of the PFK staff to remain highly relevant to the upgraded furnace. This led to minimized capital investment, a rapid start-up and no significant operational challenges switching over to the new equipment incorporating Hatch furnace technology."

Jan 1, 2012

By Arthur Barnes, Mika Muinonen, M. J. Lavigne

"The carbothermic reduction of chromite ore to produce high carbon ferrochromium is among the most energy intensive metal extraction processes performed, due not only to the highly endothermic nature of the reduction reactions but also the very high operating temperatures required for the smelting operation to separate the chrome-containing alloy from the discard slag.KWG Resources and XPS have collaborated over the last 3 years in developing a patented (Winter) processing alternative to the traditional smelting operation in which all processing takes place in the solid state at temperatures many hundreds of degrees lower than those required for liquid processing. Amongst the attractions of the process are much lower capital costs, as well as reduced operating costs, particularly of energy.A techno-economic study on the new process identifies a reduction in overall energy consumption of 70% against conventional processing and approximately 40% lower than the current best practice. By utilising more natural gas than coal based energy sources, the KWG process is able to show an overall 50% reduction in greenhouse gas emissions compared with the most energy efficient current practice. The impact of the new process on future processing is therefore regarded as highly significant, with global energy reductions equivalent to the effect of completely eliminating energy demand from a country the size of Italy.The study concluded that the potential for this process to completely revolutionise the global ferrochrome industry should not be underestimated. Its impact reaches far beyond exploitation of a regional natural resource."

Jan 1, 2015

The Beginning ! The status quo simply isn?t sustainable ! Our social license is at risk ! The bar keeps rising ? We must improve our performance, both operational and social ? We must improve stakeholder judgement of our industry by taking action collectively Implementing TSM " TSM Guiding Principles " Performance Indicators " Crisis communications " External Outreach " Tailings management " Energy management " Performance manuals, guides " Reporting " Communities of Interest Advisory Panel

May 1, 2004

By Smortchevskyk N. J.

THIS paper describes the electrical features of the locomotive now (August, 1962) under construction for Craigmont Mines. Intended for non-specialists, it avoids details of design and calculations interesting to electricians only. The paper is divided into three sections. The first deals very briefly with the mine layout and with operating conditions -existing and expected. Reference is made to economic considerations leading to the selection of the type and size of locomotive, as well as to traction diagrams and the calculations. This material is not included in the paper because of its length and because it does not represent anything new. The second section deals with engineering and economic considerations and shows, in some detail, why the A.C. system was chosen. The third section describes the basic components of the locomotive, including the voltage regulator, the rectifiers, the control arrangement and the filter, and deals with considerations affecting the selection of their rating and design. A concluding sub-section describes, very briefly, the track and trolley details and the power distribution switchgear.

Jan 1, 1963

By W A. James

The use of spectrographic semi-quantitative analysis has recently been of considerable value in establishing the geological relationships in a complicated orebody. The principal minerals found in the Mount Pleasant orebody are cassiterite, stannite, sphalerite, molybdenite, wolframite, chalcopyrite and galena, associated with arsenopyrite, pyrite and fluorite. In addition to the large number of minerals, a further com-plication is the non-uniform distribution of the economic minerals, with one mineral being the only one present in major amounts in one area and another mineral being predominant in another area. At the same time, all minerals are present to a minor extent throughout the deposit. This heterogeneity made it advisable to analyse all exploration samples thoroughly. Analysis by conventional means would have resulted in prohibitive costs. By the use of emission spectroscopy, however, it was possible to obtain, quickly and relatively inexpensively, a reasonably comprehensive picture of the orebody un-der investigation.

Jan 1, 1963

By S. Shairp

"After cooling and thickening, slurry from the second stage of the Hudbay zinc pressure leach circuit is filtered and washed on a belt filter prior to disposal. At times, the belt filter can be a bottleneck to the process. Preliminary studies show that filterability of the second-stage (HAL) autoclave leach residue can be indicated by particle size distribution of the filter feed and filtered residue cake. In particular, the Volume Weighted Mean Diameter, D[4,3], generated by a laser diffraction particle size analyzer from samples of HAL Filter feed, shows residues that filter more poorly have a lower Volume Weighted Mean Diameter than those that filter better. INTRODUCTIONHudbay produces cast zinc metal from blends of zinc concentrates at its metallurgical complex in Flin Flon, Manitoba, Canada, using Sherritt’s two-stage pressure leach process (Collins et al., 1994; Collins et al., 1995; Barth et al., 1998; Shairp et al., 2006). Pressure leaching replaced the original roastleach- electrowinning process in 1993.Filtration for the second-stage (HAL) leach residue originally consisted of two stages of vacuum drum filtration with intermediate cake repulping stirred tanks. As part of Hudbay’s 777 Project, with a designed increase in cast zinc production, a pre-feasibility study by SNC-Lavalin Inc. showed that losses of soluble zinc in the zinc pressure leach residue could be reduced by installing more efficient filtering and washing equipment. Based on laboratory performance, capital cost, installation ability, and potential operating cost savings, a 70 m2 Filtres Phillipe belt filter was chosen for the HAL residue, and commissioned in 2000/2001.When the HAL belt filter is performing well, there is no pooling of water on the surface, moisture content is relatively low, and subsequent analysis shows that water soluble zinc content is relatively low. There have been occasions where the filter has performed poorly with respect to the aforementioned parameters. Aside from the filter experiencing mechanical difficulties, there are several variables affecting leach residue filtration:"

Jan 1, 2012

By Lam. E. K., J. W. Jarvi, B. P. Bharadwaj

"The Rabbit Lake Operation is located in Northern Saskatchewan on the western shore of Wollaston Lake approximately 800 km north of Saskatoon, Saskatchewan.The Operation is owned by a joint venture of Cameco Corporation and Uranerz Exploration and Mining Limited. Cameco is the operator.The Mill started production in June 1975 under the ownership of Gulf Minerals Canada Limited and over the past twenty years has increased the rated production capacity to over twice the original design.The Mill was originally designed to process 485,000 tonnes per year of ore with an annual production of 2.0 million kg of U308 (yellowcake). During the past ten years changes in ore sources and process modifications have led to increased milling capacity and production targets. The Mill has treated a total of 8.6 million tonnes of ore and produced over 40 million kg of U308 in the twenty year period, despite the shutdown and cutbacks in operating time since 1989.The 1995 tonnage throughput was 206,000 tonnes per year. Annual production though has risen to 3.6 million kg of yellowcake despite the departure from full-time to half-time operation in 1991 (7 up-7 down). The forecast for the coming years will see tonnage rising from 300,000 to 570,000 tonnes, production of 4.5 to 5.4 million kg of yellowcake and an anticipated return in the year 1998 to full time operation.This paper will give a brief history of the Mill and focus on the present flowsheet and recent improvements to the process."

Jan 1, 1996

By A. R. Chambers

At the 1924 Annual Meeting of the Institute, held in Toronto, the writer presented some notes on the occurrence of salt at Malagash, Nova Scotia, together with a few remarks on the uses of salt. The development of these salt mines has attracted considerable attention to the district, and it may be of interest at this time to call attention to some of the newer uses of salt, and to give a brief account of the genesis of the Maritime salines, As it is not proposed to treat the subject in technical detail, and the paper is written in a lighter vein than is usual in contributions to your Transactions, you will please overlook any variations from a strictly technical method of presentation. The world's supply of salt is obtained in three principal ways: (1) By flooding shallow areas, or pans, with sea water, allowing the water to evaporate naturally by the heat of the sun's rays, and collecting the residue of solid salt. This method is employed, for example, at Turks Island, B.W.I. (2) By mining the rock salt in its natural state, and preparing it for market by a grinding process. This is the method adopted at Malagash, which is the only place in Canada where salt is actually mined. (3) By drilling a hole into an underground salt deposit, forcing fresh water clown the hole, and, after it has become saturated with salt, pumping the brine to the surface and recovering the salt by evaporation. This is the method pursued by the Canadian Salt Company, the Dominion Salt Company, and other producers in Ontario.

Jan 1, 1929

By Derek V. Ellis, Jack L. Littlepage

"Marine ecosystem effects ar1smg from the discharge of man-generated wastes to the sea can be schematized as: acute poisoning, chronic poisoning, enrichment, suffocation, temperature effects, salinity effects, toxin bio-concentration, changed production rates and changed species equilibria. A professionally designed site-specific monitoring program to check for such effects can not only safeguard the marine ecosystem from degradation, but it can also protect the industry involved from unanticipated remedial action after expensive construction has been undertaken. Monitoring programs should consist of three steps. Step 1 is an ecosystem survey which should be undertaken prior to final design of the discharge system and submission of applications for permission to discharge, because there can be considerable cost savings in obtaining information at an early stage in development. Step 2 involves location of the effluent field at the time of starting discharge, and analysing its dispersal behaviour. Step 3 consists of ecosystem monitoring with sampling stations and specific tests based on the accumulated prior information."

Jan 1, 1972

1.Assessment of methane content in coal. Given a naturally low methane content in 11 Coal Seam and the fact that the areas of the 11 Seam adjacent to the tunnelway were degassing for a very, very long time due to previous development and mining, it is conservatively estimated that the remaining in -situ methane is less than 0.5m3/tonne. 2. Continuous miner cutting rate based on the past practice. The best loading rate recorded at the past operations of Smoky River Coal was 45 seconds for a 8 tonnes shuttle car. Using these records, the maximum peak loading rate potential at the face is calculated at 0.178 tonnes per one second or 10.67 tonnes per one minute. 3. Methane release at the face. ?The actual face methane liberation, conservatively assumed at 40% of the total in situ content: 0.20 m3/tonne ?The peak cutting rate: 0.178 t/sec ?The maximum (peak) face methane release: 0.20*0.178 = 0.036 m3/sec

May 1, 2003

By M. K. Gangal, M. A. Stoakes, A. E. Hall

"The major features of the CANMET thermodynamic mine ventilation network program, developed by the Mining and Mineral Process Engineering Department of the University of British Columbia for the Canada Centre for Mineral and Energy Technology (CANMET), are described.The program is designed for use by deep Canadian mines in planning ventilation flows where the effects of auto-compression of air, moisture lift work and natural ventilation are significant. Routines to simulate stalled fans and give an optional cost printout have been included in the program.A supplementary plotting program used to simplify data interpretation is also described.The program is described with a test data example of a deep mine. It is a valuable analytical tool which can assist ventilation engineers to simulate many alternative ventilation strategies at a low cost in a very short time.IntroductionCanadian underground mines are becoming deeper and more extensive. The use of more and larger diesel-powered equipment increases the amount of air required to be circulated in these complex systems. These effects, coupled with the increasing unit cost of the energy required for mine ventilation, require that the air is used with maximum efficiency.Optimum airflow distribution can be obtained by using network computer programs enabling engineers to plan future ventilation systems based on quantitative assessments. The programs used for deep mines must make allowance for the change of air density with depth, as the assumption of incompressible flow leads to serious errors. Natural ventilation effects may vary with depth and from part to part of the mine; this must be catered for by the program. The air moisture content changes throughout the circuit and a significant portion of the fan work may be used in removing moisture from the mine; as this work varies directly with the flow, a suitable relationship must be utilized in the program."

Jan 1, 1982

By J. Guha, el, G. Bouchard, W. Zuckerk, J. Carignan, G. Archambault

The Gwillim Mine, located 8 km northwest of Chibougamau, is underlain by two mafic volcanic cycles separated by a dominantly felsic cycle. These rocks are part of the Gilman Formation of the Roy Group. The mafic rocks are cut by weak shear zones containing the "North" and "Main" veins, both east-west striking gold-bearing structures dipping 75° to the north. The felsic cycle, which is also gold-bearing, contains textures suggesting a syngenetic origin. The Gwillim Mine presents an excellent opportunity for the study of what may be two coexisting gold deposits, a volcanogenic and a veine type.

Jan 1, 1984

By Frank W. Cole, Sharanjit S. Dhillonn

A new method has been developed for calculating flowing bottom hole pressure in a gas well, using as a basis the general energy equation. Fundamentally, the method shows that a plot of flowing pressure versus depth for a gas well can be represented as a series of incremental .straight lines, with the accuracy in-creasing as the number of increments increase. It is shown mathematically that for most cases the slope of the flowing pressure versus depth curve is essentially constant, in which case a single calculation based on surface conditions will yield acceptable results. In all cases studied no more than two iterations were required for very good accuracy, and in most cases only one iteration was necessary. Several example calculations are shown and the results are compared to other commonly used methods of calculating bottom hole pressures These examples show that the method provides answers which are at least as accurate as other methods usually used, and results in a considerable reduction in computation time.

Jan 1, 1960

ABSTRACT It is critical that historical processes and concomitant exposures to specific nickel substances be understood because some diseases linked to inhalation of certain nickel-containing substances have a long latency between first exposure and disease onset, and because nickel substances vary significantly in their toxicological properties. A discussion of the smelting history and related processes at Vale Canada’s (Inco’s) Copper Cliff, Ontario, smelter is integral to the understanding of these processes. The post-1950 processing history, equipment, propensity for aerosol formation, operational procedures, and ventilation controls used by Vale Canada in roasting, smelting, converting, and copper-nickel separation is discussed.

Jan 1, 2013

By Phil A. Keele

"IntroductionGeneralThe Genesee Coal Mine is a joint venture of Fording Coal Limited and the city of Edmonton. The mine supplies thermal coal to the Genesee Generating Station operated by Edmonton Power and is located approximately 75 km southwest of Edmonton (Fig. I).Under the terms of the joint venture agreement, Fording Coal Limited has designed and developed the Genesee Coal Mine. Fording also operates the mine which has a minimum economic life of thirty-five years. Mine development started in the spring of 1987 with the construction of the dragline erection pad and mine service complex. Major development of mining areas was carried out in 1988 with the construction of haul roads, powerlines, topsoil recovery, etc. Mining officially commenced on December 14,1988.The mine produces 1.6 million tonnes of coal per year and employs 65 people. MiningGround conditions have turned out to be very poor, as expected with the majority of the overburden in the first few years a soft lacustrine clay with minor amounts of fine-grained glacial till. To compound matters, what was expected to be a relatively uniform coal subcrop turned out to be a very irregular erosional contact.The coal mined at Genesee is a sub-bituminous Class B thermal coal with approximately 16070 ash, 21% moisture, 8300 Btu/lb and 0.27% sulphur on an as-mined basis.The primary piece of mining equipment used at the Genesee Coal Mine is a M8200 walking dragline. It has an effective operating radius of 100.6 m, a 50.5 m3 bucket, and weighs approximately 3860 tonnes yielding a ground pressure of III KN/m2•Figure 2 illustrates schematically the single pass mining sequence presently employed at the Genesee Coal Mine. The M8200 is used to lift all coal out of the cut, the coal being placed in stockpiles on the prepared pad .This method maximizes coal recovery under the conditions where spoil failures due to poor material would otherwise put men and equipment at risk. The coal is subsequently loaded by the coal shovel operating on the same bench as the M8200 dragline and delivered to the plant as required.All mined areas, as required under Alberta Legislation, are to be returned to an agricultural land capability equal to or better than that which existed prior to mining. Reclamation activities, as a result, are an important and integral part of the mining process. A complete list of the primary mining equipment deployed at the Genesee Operations appears in Table I."

Jan 1, 1994