Search Documents

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By Johnna Muinonen

"The Thompson Mill processes ores from the Thompson and Birchtree Mines. While the Thompson ore has very little magnesium containing gangue, the Birchtree orebody consists of veins of massive sulphide in a rock matrix that contains a high proportion of magnesium silicate minerals. A significant fraction of the magnesium is floatable, which lead to MgO levels varying from 3-11 wt% in the Birchtree concentrate. The magnesium in the concentrate causes a higher operating temperature in the smelter, reducing furnace life.Birchtree ore represented 20-30% of the mill ore receipts prior to October 2003. Since then the fraction of Birchtree ore has increased to 50%. A reduction of the MgO in concentrate to less than 3% in the total mill concentrate was required to allow safe and economic smelter operation.In October of 2002 a miniplant was set up to simulate the Birchtree plant circuit. Several flow sheet modifications were tested that led to a proposal for a circuit having increased cleaning capacity for the scavenger concentrate and a recleaner on this concentrate. Addition of CMC in rougher cleaner feed was also found to be required. The solution was confirmed through pilot plant testing in the mill in December of 2002. A full-scale installation was designed, engineered, and installed between February and September of 2003 with commissioning in September and October of 2003. Target metallurgy was achieved one week after start-up on slurry to coincide with the Birchtree Mine tonnage increase. This paper highlights the development, design and commissioning stages of the project.The new MgO rejection circuit has successfully allowed the processing of Birchtree ores producing concentrate consistently below 3% MgO. In addition, the new circuit increased overall nickel recovery in the mill.INTRODUCTIONThe Thompson Nickel Belt located approximately 700km north of Winnipeg was discovered in the early 1950’s. Inco first produced nickel from the area in 1960. Over the years the mill has processed several ores from different ore bodies in the area. Currently the Thompson Mill processes two significantly different ores from two mines, Thompson and Birchtree. The Thompson ore is a massive sulphide orebody hosted in schist, containing feldspars, quartz and biotite. Thompson Ore is characterized by high nickel recoveries and clean, low MgO containing concentrates (<2.5% MgO). The Birchtree ore is ultramafic and contains a high percentage of Mg-silicates such as serpentine, chlorite, biotite, amphiboles and talc. Some of these Mg-silicates report to the nickel concentrate and prior to commissioning of the MgO rejection circuit the Birchtree nickel concentrate typically contained 5-8% MgO"

Jan 1, 2006

By Franz Xaver Spachtholz

K+S Potash Canada GP (KSPC) is part of the K+S Group, one of the world&apos;s leading suppliers of standard and speciality fertilizers and the world?s leading salt producer. Globally, the K+S Group employs more than 14,000 people. The K+S share ? the only commodities stock on the German DAX index ? is listed on all German stock exchanges. Legacy, K+S Group?s most recent project, is a greenfield solution potash mine and production plant in the south of the Canadian province of Saskatchewan. Therefore K+S will invest 4.1 billion CAD. With the expected commissioning in summer 2016 the company projects to reach the two-million-tonnesmark of production capacity at the new location at the end of 2017. The gradual extension of the annual capacity to 2.86 million tonnes of potash products will occur afterwards. The Legacy Project will be Saskatchewan?s first new potash mine in nearly 40 years. It is one of the world?s most economically attractive potash projects. The project will contribute to Saskatchewan?s growth through employment, tax revenues, utilities, and local partnerships. Located in the southern part of Saskatchewan?s potash belt, the deposit is too deep to be mined conventionally due to rock mechanics and high temperatures. Legacy will therefore be a solution mine. Proximity to the urban centers of Regina and Moose Jaw is imperative, with their workforces and economy, as well as access to highways, railway carriers and, most importantly in the prairies, water. With this unique project setting and mining technique, we are convinced that Legacy will be one of the most efficient, economic, sustainable and safe potash facilities in the world.

Aug 1, 2013

By H. A. Schnell

"The Phase I Mill at Cluff Lake in northern Saskatchewan was designed to accommodate a very specific high grade uranium ore. As this high grade ore was depleted, construction was undertaken on a new mill circuit (Phase 2) to process a more conventional lower grade ore deposit.The Phase 2 Mill expanded the ore throughput to 800 tonnes per day. The new process employs crushing, grinding, leaching, counter—current decantation, solvent extraction and magnesia yellowcake precipitation and drying to produce a yellowcake concentrate.This paper discusses the process decisions required for this expansion and outlines the new mill circuit. Included is a review of the start up in August, 1984.1.,INTRODUCTION The Cluff Lake Uranium deposit is located 720 kilometers north of Saskatoon in northern Saskatchewan. A high grade deposit was discovered in 1970 with the first production taking place in 1980 after lengthy hearings. The original mill (or Phase 1 Mill) was specifically designed to accommodate this very high grade ore for a very limited plant life.Pilot plant work was carried out in 1981 on the other lower grade ores found in the immediate Cluff Lake area. Feasibility and process selection studies were then undertaken as the Phase 1 mill was nearing its end of life. These studies were completed in March 1983 when approval was given to construct the new Phase 2 mill."

Jan 1, 1985

By M. du Plessis, D. F. Malan

"Crush pillars are designed to be in a crushed state whilst being formed at the mining face. The residual stress state of these failed pillars provides a local support function in mining stopes and is used in the majority of the intermediate depth South African platinum mines. On mines utilising crush pillars, the pillar dimensions are selected to achieve a width to height ratio of approximately two. This is not achieved in most cases as a result of practical mining problems and poor pillar-cutting discipline. Furthermore, pillar dimensions are seldom adjusted to compensate for the various factors governing crush pillar behaviour. The pillars should, however, be in a crushed state whilst being formed or whilst still in close proximity to the mining face to prevent potential damaging seismicity.An underground investigation was conducted into the behaviour of the crush pillars in a trial site on the Merensky Reef at Lonmin Plc. The aim of this investigation was to examine the mechanism of pillar crushing and the related rock mass behaviour. The underground test results and pillar behaviour are compared to a limit equilibrium model to investigate if the model provides a useful approximation of the behaviour of the crush pillars. This paper details some of the preliminary findings.INTRODUCTIONOn most mining operations, the design of crush pillars is based on trial and error. As the pillar strength is unknown, the pillar sizes are adjusted to obtain the correct behaviour. Crush pillar dimensions are generally selected to give a width to height ratio (w:h) of approximately 2:1, (Ryder and Jager, 2002). Several factors affect the behaviour of the crush pillars and in many cases satisfactory pillar crushing is not achieved. This results in a seismic hazard in many of the mines using crush pillars. If pillar crushing is not initiated whilst the pillar is being formed at the mining face, as the mining face advances and the pillars move to the back area of a stope, some pillars may burst while oversized pillars may punch into the footwall. If pillars are designed in such a way that they are fractured during cutting by the face abutment stresses so that the pillars will already have yielded and reached their residual strength, further compression of the pillars will be associated with an increase in load and stability will be ensured, (Ozbay and Roberts, 1988). The stiffness of the strata must therefore be greater than the post-peak stiffness of the pillar (Figure 1) or violent pillar failure and hanging wall instability will occur. The pillar design should be aimed at determining pillar dimensions for which the post-peak curve of the pillar is as flat as possible."

Jan 1, 2015

By Gordon A. Irons, H. Y. Hwang

An impinging gas jet on a water surface was studied to understand momentum transfer in oxygen steelmaking. Depth, width and oscillation frequency of the jet cavity were measured and the splashes interpreted with Kelvin-Helmholtz instability and combined Rayleigh-Taylor and Kelvin-Helmholtz instability theory. A model to calculate separate gas and liquid velocities, applying the exact momentum boundary condition, is proposed.

Jan 1, 2004

By Dong-kil Lee

A ventilation improvement index (VII) was developed in an effort to propose an optimal ventilation improvement measure for a designated mine. The index was designed to incorporate both ventilation effectiveness and cost efficiency. To verify the effect of the index, a mine experiencing a ventilation problem was selected, the ventilation assessed and ventilation network analyses were conducted. In the selected mine, four areas with ventilation difficulties were detected and an improvement schemes for each area were proposed. These were simulated through network simulation and evaluated using the ventilation improvement index. As a result, an optimum ventilation improvement scheme was proposed. The improvement scheme with the highest VII value was incorporated in the design.

Aug 1, 2013

By D. A. Sloan

THE Young Davidson mine is of particular interest because of the extremely low costs and also because of the novel method devised for pillar recovery. The outstanding feature of the mining system is its simplicity and regularity. The successful operation of this property was de-finitely assured by the rise in price of gold in 1934. The mine is situated in the southeastern part of Powell township, about forty-five miles southeast of Timmins, Ontario. The local town, two miles distant, in Matachewan, which is twenty-five miles northwest of Elk Lake, the terminus of a branch line of the Temiskaming and Northern Ontario railway. Mining is confined to one of a group of five claims. The ore occurs in a body of syen.ite porphyry which is intruded along a contact of Timiskaming conglomerates with Keewatin altered ruffs and greenstones. This intrusion extends in a north-easterly direction from Davidson creek for 3,300 feet, of which length 700 feet lies within the Matachewan Consolidated property. The maximum width of the mass is 700 feet; it tapers off as it extends east-ward. The Orebody.-The syenite porphyry is of three types, probably all differentiates of the same magma, but only one of them is gold bearing. This is a cherry-red, coarsely crystalline type which forms the central part of the mass. It is more brittle and more fractured than the others, and consequently has allowed easier access to the gold-bearing solutions. The gold has been brought in by a branching system of quartz veins and along minute fractures. It is mainly in the form of very fine &apos;free&apos; gold, but also occurs in pyrite, which is the chief metallic mineral.

Jan 1, 1942

Access to accurate real-time information is critical to maintaining efficiency and competitiveness in any modern minerals processing facility. At MMG LXML Sepon Copper Operation in Lao P.D.R., controlling the copper grade of the feed to the leaching circuit is paramount for maximising productivity and copper recovery. Since 2008, real-time analysis data has been available to process engineers from the Geoscan on-belt analyser installed on the Copper Mill feed conveyor. Access to accurate real-time results from the Geoscan has allowed the process engineers to strictly control blending based on copper grade to overcome variability in the plant feed, where conventional sampling and laboratory analysis is difficult, error prone and time consuming. In addition to enjoying these benefits since the Geoscan’s installation, in recent times the process engineers have expanded the use of the Geoscan by observing elemental results other than copper grade to control different aspects of the operation, focussing on the reduction of Gangue Acid Consumption. This paper discusses the process of expanding the Geoscan use at the operation, including an explanation of the calibration process. Additionally, a brief description of the Geoscan and its use at MMG LXML Sepon Copper Operation is provided, as well as a summary of recent calibration and analysis results. A discussion of future works concludes the paper.

Jan 1, 2016

By F. Baczek, S. S. Rocks, D. Chaiko, C. Eyzaguirre, S. Asihene, T. Walters

The majority of efforts to improve primary copper sulfide leaching have focused on solution chemistry, temperature, O2 pressure, ultra-fine grinding, the use of catalysts, etc. Historically, very few studies have focused on the solid/solution interface. A new, patent pending approach to catalyzed, copper sulfide leaching has been discovered by FLSmidth that enables manipulation of the 2-D semi-conductor properties of chalcopyrite surfaces to the benefit of higher electrochemical reactivity. Copper dissolution rates are then further accelerated by incorporating a Stirred Media Reactor (SMRt) into the process. By using minute amounts of Cu2+ to "pre-activate" chalcopyrite, leach times have been reduced from >20 hours with incomplete Cu dissolution to <2 hours with 98+% Cu dissolution at 80°C. The pre-activation process takes only minutes to complete at temperatures of 80°C or less. The total atmospheric leaching process, incorporating the pre-activation and Stirred Media Reactor is compatible with existing SX/EW processes. Results of batch leach testing are presented and possible mechanisms are discussed.

Jan 1, 2015

By J. F. Archibald

This paper reviews the formation of the Canadian Mining Education Council (CMEC) and its terms of reference. CMEC considers that Canada?s mining schools represent a distinct competitive advantage to the Canadian Mining Industry. The core objective of CMEC is to reinforce the links between the constituent schools and their individual Industry Advisory Committees. The latter traditionally provide the schools with a great deal of guidance on a range of planning issues, including recruitment, curriculum, research and infrastructure. Beyond those bounds CMEC intends to improve its ability to network with the industry and government. It is concerned overall with the objective to raise the quality and level of its educational and research contributions to meet the needs of industry and society.

May 1, 2002

By A. Aubin, H. Yang, G. Zaluski

The Athabasca Basin of northern Saskatchewan and Alberta is an exceptionally rich metallogenic region, hosting more than 2.8 B lb U3O8, of which over 927 M lb U3O8 have been mined out since extraction first started in the late 1970’s. A detailed compilation of several empirical features of 85 deposits located within the basin was conducted in order to understand the distribution and variability of the geological characteristics of the mineralization and its associated alteration. A new empirical classification was devised based on four parameters: 1) geometry of the mineralization (dimensions and relation to the unconformity surface), 2) size, grade and metallurgical complexity of the mineralization, 3) lithostructural setting, and 4) extent and nature of associated alteration haloes. This compilation defines the footprint characteristics of the Athabasca Basin deposits, which guides decision-making processes from early exploration and discovery to resource expansion and extraction.

Jan 1, 2020

By B. J. Keating

"AT PRESENT, it is not certain that any of the sulphide de in the Province of Nova Scotia attain the lower grade limit of 60 per cent sulphides over the minimum area of 1,000 square feet suggested as cut-off specifications for inclusion in this Symposium. However, several of them do include massive sections of substantial size and others represent concentrations of sulphide material that are well above average. It is felt, therefore, that a tentative classification of the deposits and presentation of their geological settings are justified and may help round out the genetic aspects of this study. Accordingly, data considered to be the most pertinent are assembled here in the event that some may fit into larger-scale patterns of mineralization that may take shape as a result of this investigation.The three principal massive sulphide deposits in Nova Scotia are the Stirling, the Smithfield, and the Walton. The locations of these are shown on the accompanying key-map (Figure 1).Three other deposits, the locations of which are also indicated on the map, are the Meat Cove, Rocky Brook, and Gays River de¬posits. Although these fall far short of the minimum dimensions and grade specifications referred to above they are singled out because they have received more than passing attention and are illustrative of the mineralization types to which they belong."

Jan 1, 1960

By M. H. Colebrook

Nickel laterites contain about 70% of all continental or terrestrial nickel resources; therefore the recovery of nickel from lateritic ores has large economic significance. The processing of lateritic ores involves the preparation and movement of concentrated aqueous suspensions. However due to complex characteristics and non-Newtonian properties, ranging from shear-thinning to shear-thickening and from thixotropic to rheopectic, a basic understanding of the flow behaviour must be developed. This understanding will assist in the development of new plants and the operation of existing plants. The work in this paper involves the characterization of three ore types from the Vermelho ore deposit to categorize them as rheologically simple to complex. Rheological testing was also conducted on pure mineral samples that represent the main minerals in these samples. The results show that the rheological properties of the ore types can be related to the surface properties and physical characteristics of the main mineral constituents.

Jan 1, 2006

By R. D. Lindsay

"Pamour Porcupine Mines, Limited is involved in the mining, milling and primary refining of various gold, gold - copper and refractory gold ores. Pamour operates five mines in the Porcupine Mining District of Ontario, and two 2,550 t/d milling facilities.Both metallurgical facilities use conventional cyanidation technology including zinc cementation for precipitation of gold and silver from solution. The precipitation process, as applied to clarified leach solutions (less than 1 ppm suspended solids) at Pamour is called the Merrill - Crowe process. Precipitates from both milling operations are treated at Pamour's Area Refinery. Schumacher precipitates, unlike Pamour No. 1, require an ''Acid Treatment Stage"" prior to refining to remove the high contained copper. This is accomplished by leaching the precipitates initiallv with sulphuric acid to remove zinc and then with sulphuric acid and manganese dioxide to dissolve copper. Refining procedures after ''Acid Treatment"" are essentially the same for both precipitates.The following considerations highlight the basic principals applied to refining cyanidation precipitates at Pamour, including:"

Jan 1, 1986

By L. Parthasarathy, S. K. Pan, M. P. Srivastava

"Total iron ore reserves in India, as reported by the Indian Bureau of mines, are 23.6 billion tons. Hematite iron ore reserves constitute about 45 % of the total reserve. If we go by the National Steel Policy-2005 projections, India’s supply of hematite iron ore would not last more than 40 years. Laboratory investigations were carried out for the development of a process flow sheet for treating low grade as well as Banded Hematite Quartzite (BHQ) iron ore. The purpose of these investigations was to aim for better resource utilization.Beneficiation studies were conducted on samples of low grade and siliceous iron ore from the Dalli mines, a captive mine of the Bhilai Steel Plant and BHQ ore from Southern states of India. The process flowsheet, developed for upgrading of low grade iron ore, incorporates wet screening of the ore at 0.5 mm, followed by grinding of the +0.5 mm fraction to below 0.5 mm. The whole –0.5 mm fraction, after grinding, was treated in a conventional hydro-cyclone and stub cyclone followed by treatment in Wet High Intensity Magnetic Separator (WHIMS). This resulted in a concentrate product having >66% Fe content from a feed containing 55.5% Fe with an iron recovery of 48 %. The process flowsheet developed for treating BHQ ore in the laboratory resulted in an increase in iron grade in the concentrate from 43.4 to 61.3 Fe % with a yield of 51.7 % .INTRODUCTIONThe classification of Indian iron ore resources have been made compatible with United Nations Framework Classification (UNFC), which is more scientific and has been adopted in most countries in the world. Iron ore reserves and resources estimated using the UNFC classification system, as of April 01,2000 are about 12,906 million tons of hematite ore and 10,628 million tons of magnetite ore. The Indian Bureau of Mines (IBM) has given a breakdown of these reserves by designation as either lumps or fines of hematite iron ore (Table 1). The percentage of the reserves reported lumps and fines are 42 and 34% of the total reserves respectively. High grade iron ore is less than 10% of the total reserve."

Jan 1, 2008

By S. L. Aaroe

"TYRETHANE PRODUCTSTyrethane® is the family brand name which has been adopted by The W. S. Tyler Company of Canada, Limited to identify its polyurethane products. Since we have been manufacturing Woven Wire Cloth for over one hundred years and have been the innovator for most of the product improvements and developments of that industry, it is only natural that our first and primary efforts involve the use of Tyrethane® as a screening medium. The product is ideal for application in the mining industry and other operations where the rate of wear on existing media is exceptionally high.In the event that you have already had some experience with polyurethane it should be poirted cut that there are many grades of the material. The polyurethane used in Tyrethane® Products will be compounded in a variety of chemistries and different heat treatments will be used to develop best mechanical properties to handle specific applications. However Tyrethane® will not be a ""cure all"" but when it is properly applied as a screening medium it will assist by lowering the unit cost for screened materials.Prior to an explanation of the advantages of Tyrethane® let's review the conventional screening media whose applications may be considered as good candidates for replacement by Tyrethane®.1.,Woven Wire Cloth.2.,Perforated metal screens.3.,Rubber faced perforated metal screens.4.,Perforated rubber screens.5.,Cast steel screen segments and weldiments.6.,Profile wire.In most cases a Tyrethane® section is designed for a one for one replacement of the material now being used. It is rarely necessary to modify the screening equipment to enable you to install the Tyrethane® Product although it may be desirable to take some steps to improve the service life of hold down components such as Clamping Strips or Tension Members. Those parts can be encapsulated in polyurethane if necessary.To fabricate the Tyrethane® section we have three basic building blocks. They are: (1) Small molded segments having square or slotted openings, (2) Reinforcing material and (3) the raw liquid polyurethane."

Jan 1, 1976

By Leslie F. Sawatsky

Raw water import requirements for oils sands mines depends mainly on factors such as ore processing rate, ore material characteristics, tailings processing technology, tailings storage systems, process water storage operations, the phase of tailings production, and non-recoverable seepage losses from tailings ponds. These factors can be readily quantified to calculate raw water import needs. Nevertheless, mine water balance continues to be misunderstood by some regulators, stakeholders and possibly even mine operators. Confusion over consumptive uses has led to a focus on recycling which is not necessarily applicable to a closed circuit water management system. Some water conservationists focus attention on raw water intake rules instead of the technical decisions that control consumptive uses. Typical oil sands mine water balances for various types of tailings operations, are analyzed to illustrate the effect of controllable and uncontrollable parameters as well as major options that need to be explored for reducing water demand. Uncontrollable parameters including tailings fines content, oil content of ore, connate water, mine depressurization water inflows and surface water hydrology. Controllable parameters include storage operations, advance water supply ahead of mining operations, type of tailings operation, net tailings pond seepage losses, and tailings impoundment operations. Potential reductions of raw water supply rates may be obtained by providing greater on-site storage to attenuate fluctuation in water demand, advance water accumulation prior to mine start up, early commencement of CT operations, thickened tailings disposal and paste technology. Water conservation measures should be focused on reducing on-site process water storage and water content of tailings material.

May 1, 2004

By G. Vibert Douglas

It often happens that the field geologist encounters a fault in ground where there is little to guide him with regard to the throw, or vertical displacement, and the heave, or horizontal displacement. The following construction gives both of these components of the fault, and the writers hope that it may prove a help to others. The construction is applicable to both normal and reversed faults. Briefly the procedure is as follows: Take a point which is common to the faulted geological feature and to the fault plane and on the downthrow side of the fault. Move this point in the horizontal plane in the direction indicated by the fault striæ. Rebat the point down to the plane of the fault and obtain its throw. Next consider the other side of the fault and truncate it down by the amount of the throw just determined. Then project the line of the geological feature through to the trace of the fault-plane at the lower horizon. The result is the relative positions of the two parts of the original geological feature as severed by the fault. In Figure r, let us consider a typical normal fault, that is, a fault in which the hanging-wall has gone down relative to the footwall. This characteristic, or its alternative, the reversed fault, is determined by observation on the ground. Let AB be the line of any geological feature such as the edge of a dyke, vein, or bedded sediment. The plane of which AB is the trace may have any dip; in the present case let us say 70° right. Let FF be the trace of a fault-plane which may have any dip; let us say 35° left in this case.

Jan 1, 1928

By Jean-François Lessard

The performance of rock pass systems has a significant contribution to the economics of underground mines. Operational concerns include hang-ups due to arching of material, blockage and degradation of the rock pass. This papers presents the preliminary results of a comprehensive rock pass database on the engineering and operation of rock pass systems in Quebec underground mines.

May 1, 2002