Search Documents

By Fabjanczyk M. W

Artificial ground support has developed into a refined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bolt is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By Maxwell HW

Pacific Coal Pty Limited (a wholly owned subsidiary of CRA Limited) managed the interests of six members of a joint venture formed to mine and export eight million tonnes of export quality steaming coal from a mine developed at Blair Athol in the Bowen Basin of the Central Queensland coal fields. The mine is now operated by Blair Athol Coal Pty Ltd. Crooks Michell Peacock Stewart Pty Limited (CMPS) was awarded a project management and engineering contract for the total mine portion. Following a feasibility study, CMPS carried out an Optimisation Study which produced changes to the design of the project, thus resulting in the project budget being reduced by some A$13 million. In spite of a number of late additions to the scope of work, the project was completed at a final cost of A$148 million, many millions below the reduced project budget. The project was also completed several months ahead of schedule. Total services were provided to take the project from feasibility stage through to the establishment of an operational facility and included project management, planning and control, accounting and financial control, as well as the organisation of engineering, procurement, construction, industrial plant commissioning, and technical training matters.

Jan 1, 1986

Analysis of different environmental scenarios and to represent, spatially, of impacted areas is possible by the use of geoprocessing techniques, specifically Systems of Geographical Information (SIG). Through these systems it is possible to create dynamic mathematical models, constituting of a georeferenced digital database and employing the integrated data originated from several sources. In this context, the general goal of this paper is to apply this tool in an environmental analysis of a specific karstic area impacted by mining activities. In order to preserve a limestone site, internationally recognised by its archaeological features, including caverns, lakes and evidences of prehistoric ages, the Brazilian government has created the Lagoa Santa Environment Protection Area. This place is located in the proximity of the Belo Horizonte international airport. In the past two decades exploitations of dimension stones have increased in this area. These exploitations have been done without a mine plan promoting several environmental impacts. The objective of this paper is to analyse these activities using SIG as a basic tool to locate the main mining related impacts and propose mitigation measures including waste and tailings disposal and reshaping of the landscape and introducing a drainage system for the considered zone.

Dec 6, 2010

Recent operating experience from West Australian open pit gold mines has shown that geotechnical input into initial design is rare. As a result, ground stability is poor - almost half the pits designed in this way suffer major failure.West Australian experience shows that geotechnical studies for individual mines are site specific, and therefore empirical experience cannot be transported from site to site. Geotechnical studies performed prior to design have resulted in significantly improved pit stability.

Jan 1, 1990

As near-surface underground mines progress deeper, the inevitable question is whether to convert from truck haulage to shaft hoisting. The desire to defer capital expenditure frequently delays investigation of the shaft option, or deferral of a decision to start shaft sinking, unless the shaft option is clearly significantly better than trucking. By the time increasing depth makes trucking uneconomic, there may then be insufficient resource remaining to justify a shaft, and the mine must close. However, had the shaft been built earlier, its lower operating costs would have permitted the mine to continue to greater depths. This paper presents a methodology for investigating the shaft versus trucks decision. As well as the typical analysis of which option is preferable at the time the analysis is conducted, the process presented illustrates how the timing of the decision to sink a shaft is critical. The paper shows how to identify the latest date at which the decision to sink a shaft can be made, after which time the shaft option will not be economic. It also illustrates how to assess the resource that may be required to justify the shaft. Considering this in conjunction with the latest decision date, implications for the companyÆs exploration program are discussed.

Jan 1, 2005

The Lake Rotokaua sulphur deposit, near Taupo, New Zealand, is a lacustrine sedimentary ore body, 220 acres in area and from 7 ft to 96 ft thick, containing, within the area drilled to date, some 20 million long tons of ore averaging 25% elemental sulphur in unconsolidated tuffaceous diatomaceous clay, overlain by about 120 ft of pumice sand and by the shallow Lake Rotokaua. An additional amount of perhaps 4 million tons of sulphur is regarded as probable in the area remaining to be drilled. Current economic studies cover the problems of mining an unconsolidated water-saturated formation with some residual thermal activity nearby; conservation and restoration after mining in a scenic recreation area; beneficiation of the ore and extraction of high- purity sulphur, principally for fertilizer manufacture. The deposit has additional importance as a pointer to possible further discoveries in the Thermal Region.\

Jan 1, 1971

MR. L. C. BALL, chief government geologist, Queensland, wrote: This paper is intended as a severely mechanical exposition of the means adopted to deal with tremendous inflows of water concurrently with development and exploitation; but incidentally it serves as a splendid exposition of close co-operation maintained between the geological and engineering branches of this large organization.I have been impressed by the completeness of the mine plans of 'Mount Isa Mines Ltd.; but only such a paper as this has brought fully to my understanding the difficulty and complexity of the solid geometry involved in the detection and plotting of the orebodies and their stratigraphic control, including faults and large-scale brecciations, and the managerial foresight that set going the initial investigations.The company's geological branch of course must be given full credit for the results attained, but it gives me pleasure that the Geological Survey of Queensland has been closely associated in much of the study.It is noted that complete drainage was affected, but it would be interesting to learn whether the brecciated zone will again become waterlogged and whether from above or from below, and whether there has been any change in the dissolved mineral content of the water as the work progressed.

Jan 1, 1939

By Carlson BL, Overton DD

This paper compares the designs of heap leach facilities for four precious metal mining projects in the southwestern United States. These four proposed projects are of small-to medium-size relative to other operating mines in the United States, and are either permitted or in the final stages of permitting. The differences and similarities in the heap leach facility designs are compared with respect to site conditions, operating conditions and regulatory requirements. This comparison provides a summary of the state-of-practice for heap leach facility design in the southwestern United States and identifies current issues in project development and process material containment.

Jan 1, 1997

By Mirabediny H, Whitchurch K

A computerised simulation model has been developed to select the most suitable digging method of a dragline operation for a given geological condition. The developed procedure uses a geological ore body model as the basis for the geologic database. The simulation selects the most cost effective dragline digging method from a database of various dragline digging methods The database consists of common and innovative dragline methods currently used in Australian open cut mines. A generalised computer package, DSLX, was extensively used to simulate various dragline digging methods. The DSLX software uses predefined functions to build strip geometry, working benches, blast profiles and spoil piles. The outputs from DSLX in form of volumetric, swing angles and hoist distances data are then aggregated with dragline specifications and site time study data to compare productivity of selected digging methods. The result of a case study showed that this procedure lends itself to the 'optimum' selection a dragline digging method for a given coal deposit.

Jan 1, 1995

The geographical and geological situations of the two mineral sand deposits currently being mined by Western Titanium Limited and the mining methods in use are briefly described. Production scheduling involving the ability to vary the proportions of the major minerals produced, together with maintaining a constant feed grade to the wet concentrator has been assuming greater importance to the company in recent years as the relative value of these minerals, due mainly to technological advances and environmental considerations, is subject to significant and rapid change. Manual calculation, even using a programmable calculator, became a trade-off between man hours and data usage. Schedules were updated infrequently and only a fraction of the avail- able data was used. In July 1975 a Data General NOVA 2/10 minicomputer with a 24K word core and three cassette drives was purchased. A suite of programmes was developed using BASIC to assist in production scheduling and these were opera- tional early in 1976.

Jan 1, 1977

Throughout 1992 Pasminco conducted field trials of the Mobile Miner MM130 at Broken Hill. The goal was to develop the machine to achieve acceptable reliability and establish production rates.

Jan 1, 1993

By Z Endut, T F. Ng, G H. Teh, J H Abdul Aziz

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Gold mineralisation at the Penjom gold deposit in the Central Belt of Peninsular Malaysia is hosted in structurally-controlled quartz-carbonate veins that display a variable degree of overprinting events under a ductile-brittle regime. Mineralised veins are categorised into two main types: shear and extension veins. Shear veins are interpreted as forming during the fold and thrust episode (D2 event) along the bedding and the Penjom Thrust ore zone. The shear veins are associated with discordant extension veins. In addition, NE- to NNE-trending splays and Penjom-Thrust-parallel reverse-dextral and locally NNW to N–S reverse-sinistral faults overprint earlier vein events, forming a new episode of extensional veins during the D3 event. This is mostly at the fault contacts of intrusives, either as shallow-dipping or vertical-sheeted stockwork or brecciated veins. At least two episodes of faulting comprising D4-D5 are evident, which postdates the main episodes of veining and mineralisation. This is indicated by a series of late episode N–S-trending sinistral and oblique to normal faults that transect and displace the Penjom Thrust and the folded footwall sequence at low angles, and are interpreted to be responsible for intensive vein deformation along the Penjom Thrust and displacement of the orebody. Structural interpretations of mineralised veins suggest that the veins were formed under a compressional to transpressional regime, with later post-vein displacement in a transtensional to extensional regime. Vein formation in response to deformation observed at Penjom reflects regional structural deformation within the Central Belt of Peninsular Malaysia and specifically along the Bentong-Raub Suture zone.CITATION:Endut, Z, Ng, T F, Abdul Aziz, J H and Teh, G H, 2015. Style of veins in Penjom gold mine, Malaysia – implications for gold mineralisation and structural episodes, in Proceedings PACRIM 2015 Congress, pp 507–514 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

With the continued drop in export coal prices (as measured in US$) delivered to the Pacific Rim market, and a fixed annual 12 per cent increase in overburden, Usibelli Coal Mine Inc was faced with the need to reduce mining costs substantially or else forfeit its foreign coal contractual commitment which amounted to about half of annual mine output. Management made a difficult and fortuitous decision to proceed with an engineered plan to switch from a two seam, extended bench dragline operation to a two seam, cast blast and spoil side operation. While down-sizing and cut-backs became the rule in all departments of the mine, the drilling and blasting budget was more than doubled. Most will agree that this is contrary to what usually happens when a mine is faced with down sizing. The more common scenario would have management target the drilling and blasting budget for decrease as a first priority to cutting cost, and then later witness a decrease in equipment performance leading to an increase in the production cost per tonne. Although Usibelli Coal Mine more than doubled its annual drilling an blasting budget three years ago, the overall stripping cost has be, reduced by more then 37 per cent.

Jan 1, 1995

By Barns K. E, Munro P. D, Brindley S. K

Ernest Henry Mining Pty Ltd started production in August 1997. The Ernest Henry orebody consists of two distinct parts, a complex supergene ore zone overlying a primary ore zone. The economic copper minerals in the supergene ore are chalcocite

Jan 1, 1998

By Meloy TP

Several important, fundamental aspects of the grinding behaviour of mineral systems are addressed. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the steady-state and dynamic population balance model (PBM) grinding equations to obtain the mill matrices and grinding selection and breakage rate functions, respectively. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalisation assumption. The severity of the non-uniqueness problem for steady state grinding is demonstrated in several examples using typical feed distributions and mill matrices. In addition, it is also demonstrated that when higher than single powers are used in steady-state mill matrix expressions during simulation or calculation (or iterative procedures are used during numerical simulation) and four or more size intervals are used considerable amount of error is propagated throughout any calculation. Each solution to a PBM, while giving the same prediction during a single mill pass, gives different solutions or predictions for mill composition upon subsequent passes. In addition, it is shown that there is a problem with building up a grinding mill knowledge base with PBMs. A similar analysis was done for the dynamic or kinetic PBM equations. The fact that the dynamic PBM Problem is degenerate or underspecified is also demonstrated. Multiple solutions to the same dynamic PBM equations are provided. Again, it is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the normalisation assumption. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions. The functionalities obtained through constraints were compared with those obtained with the normalisation assumption of Arbiter-Bhrany which relates breakage functions to particle size distribution. The capability of the population balance model to predict grinding behavior over time in various mineral grinding systems was assessed. The required functionality of selection and breakage functions for effective prediction of grinding behavior in mineral systems is discussed.

Jan 1, 1993

How many of you have felt tired and light-headed after standing or working in the sun or by the oppressive, hot, muggy conditions of an Australian summer? For those of you who have, you've experienced the minor effects of heat stress. Heat

Jan 1, 1994

By Hutton A. C

Quantitative X-ray diffraction (XRD) analyses using the Rietveld method, a standardless technique for full XRD pattern fitting, showed the mineralogy of the eastern Queensland Tertiary lacustrine oil shale deposits is dominated by detrital cla

Jan 1, 1994

Although a formal EES was not prepared for the WIM project due it winding down, CRA Ltd has been through the EES and planning scheme amendment process for its demonstration plant. Community consultation was involved with all aspects of this process. The paper outlines the WIM EES consultation program and provides lessons for future community consultation for major projects in regional locations with significant potential to alter the environment.

Jan 1, 1992

By Ono K, Oishi T

Electrochemical determination of the oxy- gen partial pressure in the Fe-0-SiO 2 ternary systems saturated with solid silica was done by measuring the activity of oxygen in a silver bath in equilibrium with the molten slags using zirconia solid electrolyte galvanic cells. From the data obtained, the activity ~Faii.st composition relations were calculated

Jan 1, 1980

A nuclear technique utilising the gamma-ray resonance scattering process is used at Isa Mine for the determination of copper in drill core and bulk mineral samples. The Copper Bulk Analyser (CBA) provides quick and accurate non-destructive copper analysis of drill core at costs two to three times cheaper than conventional chemical techniques.The almost immediate availability of sample results enhances the efficiency of the mine geologist in the duties of grade control, design of diamond drilling programmes, and input to planning. The unit has proven to be a reliable and accurate production tool requiring a minimum of technical support.

Jan 1, 1990