Search Documents

Although the diesel engine is normally considered a tried and proven power source, many new and exciting diesel design concepts are being evaluated in engine development laboratories around the world. Three such programs currently underway at Cummins Engine Company are discussed. The turbocompound engine converts into power exhaust heat energy which is normally wasted. It does this by incorporating after the turbocharger a low pressure gas turbine which is gear driven to the crankshaft. The adiabatic engine has no conventional cooling system. It converts into useful power most of the heat energy normally rejected to the coolant. The series boost turbocharged engine uses seperate low and high pressure turbochargers to increase engine output and improve transient performance. These design concepts make possible increases in diesel engine thermal efficiency from the current 33 to 38 per cent range to the 50 percent range.

Jan 1, 1982

By N G. Corner

A sea bed sampling programme by CRA Exploration Pty Limited over an area of 12 000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 106 m and contained a high grade core of 33 km2 which averaged 283 mg/m3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10 - 40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 h turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

By Ellyett C. D

This paper is an appraisal of the application of optical-mechanical-scanners operating in the non-photographic infrared wavelengths (3-5 and 8-14 micrometres) to mineral exploration in Australia. Pundamental principles of the operation of airborne scanners and their data output, thermal infrared (IR) imagery, are summarized. It is contended that thermal IR imagery often depicts the distribution of electromagnetic radiation emitted from earth surface materials better than aerial photographic techniques because optical-mechanical-scanners sample wavebands which straddle the wavelength peak of earth surface emission. To illustrate the geological features which such scanners can depict, reference is made to thermal IR imagery of a number of areas in Australia where the technique has been applied for exploration purposes. The images demonstrate that this technique can detect structural features like faults and folds, stratigraphic data by distinguishing different rock types and delineating their

Jan 1, 1973

By M P. Schwarz

In recent years, computational fluid dynamic (CFD) modelling of mechanically stirred flotation cells has been used to study the complexity of the flow within the cells. In CFD modelling, the flotation cell is discretised into individual finite volumes where local values of flow properties are calculated. The flotation effect is studied as three subprocesses including collision, attachment and detachment. In the present work, these subprocesses are modelled in a laboratory flotation cell. The flotation kinetics involving a population balance for particles in a semi-batch process has been developed. From turbulent collision models, the local rates of bubble-particle encounters have been estimated from the local turbulent velocities. The probabilities of collision, adhesion and stabilisation have been calculated at each location in the flotation cell. The net rate of attachment, after accounting for detachments, has been used in the kinetic model involving transient CFD simulations with removal of bubble-particle aggregates to the froth layer. Comparison of the predicted fraction of particles remaining in the cell and the fraction of free particles to the total number of particles remaining in the cell indicates that the particle recovery rate to the pulp-froth interface is much slower than the net attachment rates. For the case studied, the results indicate that the bubbles are loaded with particles quite quickly, and that the bubble surface area flux is the limiting factor in the recovery rate at the froth interface. This explains why the relationship between flotation rate and bubble surface area flux is generally used as a criterion for designing flotation cells. The predicted flotation rate constants also indicate that fine and large particles do not float as well as intermediate sized particles of 120 - 240 ¦m range. This is consistent with the flotation recovery generally observed in flotation practice. The magnitude of the flotation rate constants obtained by CFD modelling indicates that transport rates of the bubble-particle aggregates to the froth layer contribute quite significantly to the overall flotation rate and this is likely to be the case especially in plant-scale equipment.

Jan 1, 2005

By R S. Suglo, G-K Er

Mineral processing is an essential component of a mine production chain and it accounts for significant proportion of the production cost. Over the past decade, significant research progress has been made in processing plant efficiency using theoretical, experimental and simulation modelling techniques. However, these studies are limited to process plant system as stand-alone units with no interactions with the mining units. In order to maximise the total mining system efficiency and more accurately simulate the system, the processing plant must be modelled as part of an integrated mining system. This becomes increasingly important in continuous surface mining systems, with limited ore processing capacity. In addition, plant efficiency is roughly estimated with known parameters or with simplistic statistical data, without regards to the stochastic processes governing these parameters, such as processing plant feed introduction. In this paper, a comprehensive model of the ore processing plant system is given and the object-oriented design (OOD) of the system is briefly introduced. The joint operation of ore processing plant system and haulage system is analysed. Numerical modelling is used to analyse the ore processing plant system under different conditions. Analysis of the results show that the optimum plant capacity is 0.7 tons/sec (2520 tons/hour). The results also show that the plant system resources cannot be fully utilised because the production rate is always less than the plant capacity. When plant capacity reaches an optimum value 0.7 tons/sec, the production rate is about 0.64 tons/sec. The underlying stochastic processes associated with plant and mine capacities cause this variability. In order to reduce this variability, there is the need to tightly set tolerances for the function variables.

Jan 1, 2003

A major factor in the economic development of New South Wales has been the ready availability of coal for the major industrial and urban centres of Sydney, Newcastle and Wollongong. Historically, the presence of high quality coal near these areas has acted as a catalyst to urban and industrial growth. This easy access to low cost coal resources over the past 200 years has given rise to a commonly held belief that New South Wales contains vast coal resources sufficient to meet any foreseeable demand. However, a recent study undertaken by the Coal Resources Development Committee has found that New South Wales is likely to face a serious shortage of economically mineable coal in the future. Forecasts predict that demand for New South Wales coal will increase by about 40 per cent, and then remain at about that level for at least a further ten years. To meet such demands, the coal industry will require access to economic high quality coal resources.

Jan 1, 1995

The collapse of the I.T.C., the subsequent fall in the price of Tin, and the lifting of quotas saw the Renison concentrator resuming full seven- day operations at maximum capacity in 1985/86. Performance was sus- tained in terms of grade and recovery, and in some areas improved, over this period. A further challenge was declining head grades, and the need to treat higher proportions of less amenable ore types. The complexity of the flowsheet and the method of mining and ore handling predisposes the process to unstable operation, and solving this problem comprises a major component of the current development effort. The concentrator has an imbalance of capacity between processes, and excess in some areas is being adapted to enhance the capacity of others. Magnetic susceptibility of various minerals is being exploited to greater effect. Significant performance gains are achievable by improving exist- ing unit process efficiency, particularly in grinding, gravity processes and Cassiterite Flotation. This paper reviews the metallurgical developments, both recently implemented and planned for this year, which have contributed to main- taining Renison Limited in a competitive position in the post I.T.C. Tin industry.

Jan 1, 1988

By Smith T. N, Wild M. B, Elliot B. J

The process of flash smelting of nickel sulphide ores, as practised at the Kalgoorlie Nickel Smelter, is described. The critical variables in the operation of this process are identified. The design of a pilot-scale, turbulent-jet flash reactor which models the essential features of the industrial smelter is described. A report of its operation and application to an investigation of the ignition of particles of sulphide species is given.

Jan 1, 1991

By Anderson JDC

Opencast Lignite Mining requires topwall strata of seams to be fully depleted and footwall aquifers sufficiently depressurized. To prevent a spread of the cone of depression into protected wetlands some distance away, alternatives had been investigated such as closing water works, underground slurry wall barriers and recharge by infiltration. As a result of these investigations, the infiltration method has been chosen and in a first phase during the next decade it will utilize as much as 55 x 106 m3/year. Using this approach, the survival of the wet lands is assured.

Jan 1, 1988

By Senanayake G

A sample of crude copper powder produced by the CLEAR Process was refined by dissolution and recovery in sulfate media using the Parker Process. The Parker Process offers an alternative method of copper recovery to electrorefining and allows a range of Eh and pH conditions to be used to provide further discrimination of impurities. High purity copper powder was recovered by the Parker Process even in the presence of added impurities when the Eh and pH was maintained near constant throughout the refining step.

Jan 1, 1984

By Brechtel C. E

Providing adequate airflow to effectively dilute and remove diesel pollutants in large mine working headings is a little researched area. A simulated diesel mucking operation was carried out in the Exxon Colony Pilot Mine in Colorado to establish expected levels of diesel pollutants in dead-ended working headings. This heading was nominally 15.3 m (50-ft) wide by 9.2 m (30-ft) high. Two face ventilation systems were tested using sulfur hexafluoride tracer gas to represent the diesel pollutants. The results of these tests showed that conventional face ventilation systems operating at high flow rates could adequately ventilate diesel equipment in the 447-522 kW (600-700 hp) range, even in a dead heading 91.4 m (300 ft) in length.

Jan 1, 1988

By Nightingale RJ

A column (50 cm 4) provided with a bell charging mechanism and a rectangular perspex insert was used to investigate the inter-relationship between charging pattern, size analysis and velocity profile for a number of charging methods. It is shown that a strong correspondence exists between size distribution and velocity profile for bell charged ore and coke and that decreased coke volumes cause higher pressure drops and increased central flow in beds with "V" shaped layers. It is also shown that a bell charged mixed burden exhibits greater segregation than when it is bell charged as layers and that when uniformly charged the mixed burden shows least segregation and a virtually flat velocity profile. A relationship is derived for "V" profile charges showing the extent of central segregation with furnace size.

Jan 1, 1975

Grade control plays an essential role in the good running of a mine. The factors at play are many, starting from a good analysis of the geology and a correct sampling procedure. Once this is achieved (and it is an essential prerequisite), the problem is to adequately define what is ore and what is waste. This paper tries to show, through a small example, how simple geostatistical techniques (variography, and moving average or kriging), can help in accurately defining these limits in a geologically homogeneous zone, thus allowing optimal use of the available information.

Jan 1, 1987

By Bangerter PJ

The use of gravity concentration is, and has always been, the conventional primary method for gold recovery from alluvial deposits. The development of high capacity cone concentrators and metallurgically efficient wash-waterless spiral separators has had some impact in the technology for alluvial gold processing, but perhaps more significantly has led to the relatively recent use of this gravity concentration technology in grinding circuits of hard rock ore for "coarse" gold removal and for scavenging gold locked in sulphides from cyanidation tailings streams.Gravity concentration systems are relatively low-cost, non-polluting and energy efficient; and their judicial use in gold treatment plants can significantly reduce overall capital and operating costs.The application of modern gravity concentration technology to hard-rock and alluvial gold ore treatment is discussed. Flowsheets and test and operating data from a number of gold processing operations incorporating gravity concentration treatment are presented.

Jan 1, 1984

By Moort van J C

A new low-intensity magnetic separator which operates by spinning particles in a continuously rotating magnetic field is able to reduce particle entrapment of non-magnetics to an almost insignificant level. In such separators the removal of ma

Jan 1, 1997

Permian ultramafic and associated rocks form a belt in East Nelson and contain widespread, but minor, chromite and copper mineralisation and some mining was carried out last century. Since mining ceased, about 1910, little mapping of the belt has been carried out although its origin has been debated vigorously. Recently it has been inferred to form part of a ophiolite sequence, which has been tectonically disrupted to form a melange, and several 'plate -tectonic' models have been proposed. Mapping in the central part of the belt has shown that mTlanges are to the east of the ophiolite sequence. Faulting is widespread so that in anyone section part of the sequence may be absent. Some of the faulting is difficult to recognise and probably took place during or soon after the sequence accumulated. Other faulting is clearly of Cenozoic age and includes major NNE striking faults, with large horizontal displacement, and approximately east-west striking faults with almost entirely vertical movement. The writer agrees that 'plate tectonics' could provide an acceptable explanation for the origin of the ophiolite sequence but the models so far proposed do not take into account the nature and field relationships of the rock units present. Copper Mineralisation is largely controlled by the younger faults, particularly those striking about north-east, and is largely confined to the western part of the ultramafic rocks particularly where slivers of the volcanics of the adjacent Lee River Group are enclosed. Mineralisation, along NNE striking shear zones, has recently been found in the volcanics some distance from the ultramafic rocks. The chromite mineralization is in the form of primary layering in the basal part of the ultramafic belt although in places it has been concentrated into lenses probably during serpentinisation.

Jan 1, 1977

Minerals similar to the indicator minerals used in kimberlite exploration are widespread in the Cainozoic alkali basalts of north Queensland. Magnesian ilmenite, pyrope garnet, chrome diopside, chrome spinel, phlogopite and zircon were recovered from most of the localities examined. The occurrence of these minerals creates significant problems when indicator minerals are used for diamond exploration. Basaltic ilmenite is visually similar to kimberlitic ilmenite. Untransported grains are rounded and have pitted surfaces. Basaltic ilmenite grains often have exsolution lamellae and reaction rims of titanomagnetite. Although kimberlitic and basaltic ilmenite are chemically similar, basaltic ilmenite grains are usually less magnesian than their kimberlitic counterparts. Basaltic ilmenite contains very little Cr203. Pyrope garnet occurs as megacrysts and in a variety of xenolith lithologies in north Queensland basalts. Most basaltic garnet is Cr-poor and comparable with kimberlitic garnet from Groups 3 and 5 of Dawson and Stephens (1975). Wine-purple, chrome-bearing garnet is common in kimberlite but rare in basalt.

Jan 1, 1984

Intermontane valleys form unusual features of compressive mountain belts both in the sharp topographic break they represent and in the strike-slip displacements often associated with the valleys. Such strike-slip motion seems hard to reconcile in the actively deforming Andes where reconstructions have indicated nearly perpendicular Cenozoic plate convergence. Detailed study of a part of the Argentine Andes between latitude 31-33¦S suggests that, although strike-slip displacements may have largely created a prominent intermontane valley system, no Holocene strike-slip displacements are observed amid the relatively active compressional deformation along the mountain belt flanks. New plate reconstructions, treating the Nazca plate as two microplates separated by fractures along the Nazca Ridge, predict large components of strike-slip motion between the South American and Nazca Plates for the period from 10 to 5 Ma. These reconstructed plate motions are consistent with strains derived from recent kinematic analyses of minor faults along the southeast margin of the Puna plateau and the general timing of tectonic phases in the Andes.

Jan 1, 1987

During the 20th century, the iron ore mining industries of Canada and the United States passed through several periods of transformation. The beginning of the 21st century has seen yet another period of transformation, with the economic failure of a number of steel companies, the acquisition of their facilities by more viable steelmakers, and the consolidation of control within the North American iron ore industry. Changes in Canadian and United States iron ore production and the market control structure involved are analysed. The consolidation of ownership, formation of foreign joint ventures within North America, planned divestitures of upstream activities by steelmakers, and industry changes made to ensure availability of feedstocks will be reviewed. The traditional isolation of the Canadian and United States iron ore operations and their strong linkage to downstream steel production will be discussed in the context of a changing global economy. Management-labour conflicts that have taken place and agreements made during 2000 through 2004 will be discussed in the context of the economic environment leading up to these agreements. Cooperative agreements between competing Canadian and United States companies to resolve client needs in processing and blending will be examined. A joint industry-government project designed to use new technology to produce direct reduced iron nuggets of 96 - 98 per cent iron content using non-coking coals will also be assessed. Changes in iron ore transportation methods, ownership and infrastructure will be reviewed for both rail and inland waterway transport between Canadian and United States companies. A brief analysis of social and environmental issues relating to sustainable development of the Canadian-United States iron ore industry will be included.

Jan 1, 2005

A standard practice of auditing mill designs has developed in the mining industry. The purported aim of this task is to ensure that the mill being offered conforms to the design specification, thus reducing the purchaserÆs risk. However, careful examination of the auditing methods used in the past shows that this is not the case. In some cases, what auditors have been providing is effectively a quality assurance check of the input data, not a full independent audit of the vendorÆs design. It will be shown that these past auditing methods have contributed to the stagnation of mill specification development. This lack of specification improvement combined with the current trend towards increased allowable fatigue stress ranges can result in an increase in risk for the purchaser.

Jan 1, 2002