Search Documents

The concentration of Mt. Morgan sulphide ore has always been attended by serious loss of gold. Until recently, with a simple selective flotation flowsheet, even the lowest grade of ore milled-about 2 dwt. per long ton-thislloss was 0·9 dwt., whilst for average to high-grade ore, 3·5 to 5 dwt., the figure was 1·5 to 2·0 dwt. Early in 1937 it was decided to equip the research laboratory for an investigation into the condition and location of the escaping gold and the physical and mineralogical barriers preventing its recovery.With the completion of: this equipment in July 1937, trial and error testing, which had been explored to exhaustion, was abandoned and a five months' research programme mapped out and commenced. Based on the knowledge so gained, a flowsheet combining primary desliming, bulk flotation of the natural slime, selective flotation of the deslimed fraction, and cyanidation of the selective flotation tailing was drafted and tried with encouraging results in a 70-lb. per hour pilot plant. This flowsheet, modified to meet current circumstances, is being dove-tailed into the existing 1,500-ton sulphide ore concentrator, though the cyanidation treatment is actually carried out in the oxidized ore mill, to which the flotation tails are pumped.RESEARCH EQUIPMENT(1) Five tube elutriator (Fig. 1) t built in the company's workshop.

Jan 1, 1939

By M D. Hannington

On the southern flank ofLihir Island, a group of three volcanic cones were discovered at water depths from 1000 - 1500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts, and porphyritic phlogopite basalts. One of the volcanoes has a recently erupted ejecta blanket (recovery of warm ash!), containing a suite of abundant mafic to ultramafic xenoliths. These xenoliths appear to represent a unique cross-section of subduction-modified mantle material sampled by volatile-rich primary fore-arc magma during its ascent to the seafloor. The most spectacular finding was the discovery of an active hydrothermal system with associated vent fauna and mineralization at Edison Seamount, and the recovery of unusually gold-rich (up to 43 ppm Au) hydrothermal precipitates in 1050 m water depth at the top of Conical Seamount, only 25 km south of the world-class epithermal Ladolam gold deposit on Lihir. The discovery of submarine hydrothermal vents associated with highly alkaline, quartz-undersaturated fore-arc volcanics represents a significant departure from similar hydrothermal systems on the mid-ocean ridges and in back-arc basins. The high gold grades in hydrothermal precipitates at Conical Seamount may indicate the first documented example of a shallow-marine epithermal system analogous to those known on land, and has important implications' for the gold potential of submarine arc environments.

Jan 1, 1995

Apparently there is little inclination on the part of mining engineers to supplant the transmission of power by compressed air with it's formidable rival, electrical transmission. No doubt there are many advantages to be claimed for compressed air that render it parculiary well suited for the conditions which characterise underground work.

Jan 1, 1902

By M R. Stevens

An approach of geological mapping and descriptive criteria has been used to identify hydrothermal eruption breccias, named the Onemana Breccia. These in part mantle a gold bearing fossil hydrothermal system located on the eastern side of the Coromandel Peninsula, New Zealand. Whilst eruption breccias are documented from active and recent geothermal centres within the Taupo Volcanic Zone and in Northland their recognition at Onemana is the first confirmed discovery for this lithotype within ancient hydrothermal systems of the Coromandel Volcanic Zone. At Onemana the widespread occurrence of silicification, sinters, volcanic lake sediments, eruption breccias and advanced argillic alteration allows classic hot spring epithermal modelling. The geological setting, distribution, lithological characteristics, hydrothermal alteration and trace element geochemistry of the Onemana eruption breccias are described. These breccias are closely comparable with hydrothermal eruption deposits elsewhere, particularly those in active ore forming hydrothermal systems. Consideration is given specifically to the role of the Onemana Breccia in an exploration strategy for discovering epithermal gold-silver deposits.

Jan 1, 1991

WHILE in the employ of the Broken Hill Associated Smelters and the Electrolytic Zinc Oompanies at their South Melbourne Research Station, the writer was detailed to investigate the principles underlying the Parkes Process with a view of determining:1. The Interdependence of the variables:(a) Quantity of zinc required per charge,(b) Temperature of stirring of each zincing,(c) Silver content of the bullion after first zinculg,(d) Silver content of the bullion after second zincing,(e) Silver grade of the crusts produced for retorting, with reference to the method of working the Parkes Process then in operation at Port Pirie.2. The possibility of effecting improvements in the Port Pirie practice of desilverising, especially with respect to:(a) Silver grade of the crusts produced for retorting.(b) Quantity of zinc required per charge.The method of desilverising in practice at Port Pirie was a two-stage zincing.In both zincings the bullion was cooled to its solidification temperature and the silver crusts which separated from the lead were completely removed.The crusts from the first zincing were retorted, and the crusts from the second zincing were returned to the first zincing of the next charge.

Jan 1, 1925

By Spooner H. W

The paper describes the search for mineral deposits in an area of 4,500 sq. miles of south-west Tasmania. The area is one of difficult access and the problem of speedy movement and maintenance of field parties was solved by the use of helicopters. The programme has followed a systematic pattern of the aerial photography of the exploration area with the preparation of photQmosaics and topographical base sheets from these mosaics. Geological maps were initially prepared by photogeological interpretation and making use where possible of pre-existing information. The maps produced were later checked by ground traverses. Geophysical maps were obtained by the use of airborne magnetic, electromagnetic and radiometric methods. Geophysical and geological anomalies were checked on the ground by a campaign using ground geophysical equipment in the former case and geological and geochemical work in both instances. Audio Frequency Magnetic and Induced Polarization techniques were used in an area which was covered by several hundred feet of Tertiary sediments.The campaign has reached the stage of the drilling of specific targets.INTRODUCTIONThis paper describes the activities of Lyell-E.Z. Explorations (L.E.E.), an organization which was formed in 1956 by the Mt. Lyell Mining and Railway Co. Ltd. and the Electrolytic Zinc Co. of Australasia Ltd. to explore for mineral deposits in an area of approximately 4,500 sq. miles in southwest and southern Tasmania. To provide the necessary personnel and equipment for this project the exploration resources of both Companies were pooled and augmented and a headquarters was established in Queenstown. The work was directed by a Committee of four made up of officials from both Companies; a review of this structure has recently been presented by Hall (1959).

Jan 1, 1960

Supplement to Proceedings Number 120, December, 1940. Drawings accompanying paper by T M Carey 'The Surface Plant at the Zinc Corporation Mine, Broken Hill'

Jan 1, 1940

By Camier R. J, Perry G. J

Extensive deposits of brown coal exist in the Gippsland Basin, primarily in the Latrobe Valley. The total quantities of economically winnable coal in this region of Victoria and in other smaller fields are large enough to adequately assure Victoria's future electricity needs and to also provide large quantities for alternative applications, including liquefaction. As a result of the recent conflict in the Middle East attention has again been focussed on the production of synthetic fuels from coal. There have been many investigations over the years into the production of oil from Victorian brown coal. The purpose of this paper is to summarise the scope, objectives and major findings of these studies, with the emphasis on the direct hydrogenation route for converting brown coal to oil. The principal alternative processes are carboniastion and hydrotreatment of the product tar, or gasification and Fischer Tropsch synthesis of liquids from the product gas. The attractions of Victorian brown coal which have encouraged these studies include: ò the vast reserves of Victorian brown coal and the favourable conditions for low cost mining, ò the high quality of the coal (low ash, sulphur and nitrogen contents), ò the high reactivity of the coal giving high yields of product in hydrogenation to liquid fuels, ò the extensive data base available on the resource and its characteristics, and ò the availability of a skilled workforce and extensive infrastructure in the Latrobe Region to support a major resource development project. These advantages have been partially offset by: ò the high moisture content of the brown coal and the cost of drying, and ò the priority previously given to electricity generation in the allocation of the brown coal resource.

Jan 1, 1992

By Woodcock J. T, Sparrow G. J, MacRae C. M

The external urfaces and interiors (as polished sections) of particles of coconut hell and extruded peat activated carbons taken from everal Australian carbon-in-pulp operations were examined with an optical micro cope, a scanning electron microscope, and an electron microprobe.Calcium carbonate (calcite) precipitated from the pulp was the major inorganic material on the external surfaces of the carbon particle, but several ore minerals, including quartz, hematite, pyrite, arsenopyrite, and clay minerals were also identified, along with trona, gypsum, a nickel cyanide, and a magnesium salt. Sections of carbon particles showed that calcite was virtually the only introduced inorganic material inside the carbons.It was distributed in the pores and cracks throughout the coconut shell carbon particles but tended to be concentrated in the outer layers of the extruded peat carbon particles. The mechanism of calcite formation and deposition is uncertain. Gold X-ray dot maps showed that gold was distributed through to the centre of coconut shell carbons and to a depth of at least 500 µm in extruded peat carbons. The distribution of gold within the carbon particles was similar to that of calcite.

Jan 1, 1988

By M Stevens, M P. Simpson, J L. Mauk

The Karangahake deposit was the second largest producer of gold-silver bullion in the Hauraki Goldfield, New Zealand. New mapping of a 2 + 3 km (6 km2) area demonstrates that hydrothermal alteration surrounds productive veins. Wallrocks proximal to veins are intensely altered and alteration decreases toward the margin of the system.   At Karangahake, distinct zonation of adularia, calcite, epidote, illite and illite-smectite surrounds gold-bearing lodes with unaltered rocks containing magnetite and plagioclase occurring on the margins. Adularia, illite, illite-smectite, and calcite zonation defines hydrothermal alteration extending 2 km to the east of productive lodes. Epidote and adularia zonation occurs proximal to veins. The adularia zone compares well to potassium/thorium studies conducted in the area. Illite zonation is well developed to the east of the veins grading into interstratified illite-smectite containing 5 to 40 per cent smectite 1.5 km from the Maria Lode. Calcite is restricted to the east of the study area occurring in 18 per cent off surface samples. Less altered rocks containing plagioclase and magnetite occur distal to veins. The magnetite occurrence compares well to aeromagnetic studies conducted in the area.   Adularia and coexisting adularia and albite indicate the host rocks were highly permeable. Epidote, illite, illite-smectite and previous fluid inclusion evidence implies temperatures graded from >240¦C in the core of the system to approximately 150¦C on the periphery. The alteration association of quartz, adularia, calcite, pyrite, chlorite, illite and illite-smectite reflects a near-neutral to weakly alkaline water. Calcite occurrence and the absence of zeolite imply the fluid contained significant dissolved CO2.

Jan 1, 2005

The National Economic Viewpoint? Any substantial project undertaken by private enterprise would normally be subjected to a Discounted Cash Flow analysis of its commercial viability, and would proceed only if the rate of return was judged satisfactory. A 'national viewpoint' analysis attempts to do the same but from the viewpoint of the community as a whole. The objective is to ensure that those projects are undertaken which yield the best return, economic and social, to the nation as a whole.

Jan 1, 1984

By D Barclay, S Mercer, S Wright

Mine water management is often an afterthought in mine planning processes and can introduce significant risks to projects when studied as a stand alone component at a later stage in the mine design. Incorporation of a mine dewatering and pore pressure dissipation strategy in the early stages of mine planning is imperative in order to minimise constraints on the production schedule, to match designed pit slopes and maximise project value for an open cut mine option such as Olympic Dam. A risk-based mine planning approach was adopted during the project selection phase study whereby water management was introduced into mine planning, scheduling and the development of an operational strategy. Hydrological and hydrogeological studies and outputs were successfully integrated into the various iterations of the mine planning cycle during early selection phase to manage the potential water management risks associated with pit slope depressurisation and access to dry working conditions during rapid advancement of mining phases.An extensive network of vibrating wire piezometer sets and long-term depressurisation testing characterised aquifer conditions and demonstrated that hydraulic connectivity exists within the geological profile due to the presence of structures and resource drill holes which enhance vertical connectivity. This connectivity, along with underdrainage from mining activities contributes up to 100 m of depressurisation in low permeability units.A pit dewatering strategy incorporates the mine planning schedules and accounts for operational constraints as to the location and development of the dewatering wells, storages and pipelines. Numerical modelling generated a range of likely pit inflows and dewatering requirements with the average initial dewatering discharge likely to be 150 L/s and reduce quickly to 50 L/s after five years, depending on the premine schedule.Coupled hydrogeological and geotechnical assessments were also carried out as part of the mine planning cycle and indicate that successful dewatering will go a long way to reduce the pore pressures within key geotechnical units during the rapid mining phase where around 300 m of cover sequence is stripped in five years. However, the residual storage in the primary aquifer and the residual pore pressure in underlying low permeability units will need to be dissipated (in-pit horizontal holes) as the pit floor advances. Pit slope design angles are sensitive to depressurisation and dewatering and up to 70 per cent depressurisation of key geotechnical rock units are required. Whilst an accelerated program of aquifer dewatering supported by lithostatic unloading should drive rapid depressurisation in the lower permeability units, intervention is anticipated in key geotechnical units such as the Tregolana Shale and volcaniclastics. The extent of induced drainage will ultimately depend in part upon the mining rate and geotechnical stability requirements. Practical operability testing addressed the potential for operational constraints to mine depressurisation activities such as congestion and mining schedule development within the pit and identified that depressurisation drilling can be achieved even with reduced access availability. Mine operations and planning groups established design criteria and considered the likely inoperable periods following rainfall events of seven to 14 days to manage the base surge and minimise impact on production. In-pit surface water management options to minimise operational disruptions during and after significant rainfall events were estimated used a stochastic approach.

Jan 1, 2009

Interest in those physical properties of minerals which might be used to good effect in prospecting is not new. Early in the nineteenth century attempts were made in th'e Cornish mines to measure the natural electric potentials set up by chemical changes proceeding in the lodes. The distortion of the earth's magnetic field by bodies of strongly magnetic iron ore received early recognition in Sweden. Treasure-finders, working on the principle of electrical induction, appear to have been invented about eighty years ago, though were probably not then applied to mineral exploration. By the end of the nineteenth century Eotvos, a Hungarian physicist, had constructed a highly sensitive type of torsion balance capable of measuring the minute distortions in the earth's field of gravitation resulting from variations in the density of the materials composing the crust. During the first decade of this century he demonstrated its value in tracing rock-salt deposits in virtue of their low density compared with the surrounding rocks. Geophysical prospecting began to be recognised as having a very definite value and its development gathered momentum. Its great expansion took place after the 1914-18 war, when its value in oil exploration was amply demonstrated, and this expansion has continued to the present time and shows no signs of abating.Divisions of Applied Geophysics.The four main divisions of applied geophysics are electrical, magnetic gravitational and seismic. With the importance of ores of radio-active metals, one might add to these a radio-active division. The first two are more important to the field of mining, but techniques based on gravitational attraction have their uses in particular cases. Seismic methods are not generally suited to the exploration of metallic ores, but have proved of enormous value in the search for petroleum. With vast quantities of oil as the prize, more money has been lavished on the deve10pment and practice of these methods than on all the others put together.Geophysical Prospecting Methods.Geophysical prospecting methods may be used to detect a mineral deposit directly in virtue of differences in the intensity of some physical attribute common to it and the enclosing country rock. Examples of this are the detection of rock-salt by gravity measurements, or of iron ore by magnetic methods. Of much wider application, however, is the indireot approach in which the aim is to determine, by geophysical means, the geological structures controlling the disposition of mineral deposits. These structures may be partly known from geological work, in which case geophysical methods are useful adjuncts. Where, because of an 'unbroken cover of overburden, no useful geological information presents itself, scout drilling or geophysical prospecting are the only alternatives. Overburden is here intended to mean any covering material not, involved in the structures controlling the mineral deposits. Prospecting for petroleum amounts to the detecting of favourable reservoir structures, and as the chief types of such are the same the world over...

Jan 1, 1950

By Cordner G. D

Titanium is not yet being produced on a commercial scale despite the facts that it has some impressive properties, and that it occurs very abundantly in easily-mined, highgrade oxide ores. One important reason for this is that the excellent mechanical properties of the metal were not widely recognised and appreciated until about twenty years ago.Another factor which has tended to retard progress in titanium metallurgy has been the realization that the oxide minerals of titanium are very stable; in other words, considerable energy has to be expended to reduce the oxide to metal. Table 1 presents the minimum energies which would have to be expended to produce one ton of each of the metals, aluminium, magnesium, titanium and iron from their respective oxides under theoretically ideal conditions at normal temperature and pressure. At higher temperatures, the minimum energy requirements are different, but the values for the various metals still fall in the same order as indicated in Table 1.In actual fact, the energy consumption in the case of any particular metal is higher than the ideal value by an amount which can be determined only by' the results of plant practice. The only general conclusion that can be drawn from the data in Table 1 is that it might eventually prove...

Jan 1, 1950

As requested by my fellow members I shall endeavour to read a paper on the Treatment of the Auriferous Sulphide Ores of Kalgoorlie from a metallurgical standpoint. Before going into the subject it will be necessary for me to make some slight explanations. As most of you are aware many of our London friends holding interests in some of these mines think it necessary that their doings should be shrouded in mystery. The result of this is that in some cases it is impossible to get any official figures from the mines for this paper. I must ask you not to lose sight of the fact that in treating the sulphide ores of the Kalgoorlie mines we had absolutely no data to start on, and that to-day. we are just beginning to get a fair grip of tbe subject; and though very high extractions were announced when the first plants were started on sulphide ore, it was well known that this was only to maintain the public confidence in the mines to allow time to make necessary adjustments; and, as showing the advance made in the treatment of the ore, I notice several of the mines have published the results of the final or re-treatment of the residues of their first sulphide treatment. I have also had the opportunity afforded me of thoroughly sampling the residues of several of the principal mines, and find the results as now published absolutely correct.

Jan 1, 1901

By Met M, Worner H. K

In pursuance of the investigation into the influence of various elements on the properties of lead during the past year, the effect of several elements on the creep rate of commercially pure lead has been investigated; a standard initial stress of 500 lb. per sq. in. having been adopted for comparison purposes. Other work which has been carried out indicates that the relative results of creep tests may be altered by varying the applied stress, but this aspect of the problem will need to await further investigations for itscomplete elucidation. The results obtained with dilute tellurium alloys are considered sufficiently interesting, and in some respects are so extraordinary, as to warrant publicatiorr at this stage.n must be realised however that, since the results obtained appear to be at variance with those said to have been obtained in practice and those previously published, the present investigation can only be considered as a contribution to our knowledge of the general problem.Consequently it is not considered advisable or necessary to offer detailed explanation of the results given. In fact, some features of the tests about to be described will need further investigation before an adequate explanation is possible.

Jan 1, 1936

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

Techniques have been developed for the dissolution of a wide range of rocks and minerals by a sodium peroxide sinter process. A olarge number of elements are determined by atomic absorption spectroscopy, and other elements such as arsenic and sulphur are determined by chemical analytical methods. The methods adopted to overcome inter-element and ionization effects on the atomic absorption results are discussed.

Jan 1, 1974

The Use of Automated Mineralogy to Interpret the Batch Flotation Performance of Merensky Reef Ore

Sep 13, 2010

Electricity will play a major part in providing energy services in the 21st century. Ecologically Sustainable Development (ESD), that is accommodating the needs of the present without compromising the needs of future generations, will provide a focus for optimising the use of electrical energy. Environmental externalities may redefine the cost structure of electricity. Strong corporate environmental management will ensure that current environmental objectives are met and that future ones, identified by the ESD process and environmental externalities accounting, can be developed and implemented by receptive business managers. This paper addresses the current environmental issues of electricity production. It outlines a management strategy for the SECV becoming a community leader in protecting the environment. ESD is discussed in terms of using non-renewable resources wisely, extending their availability and putting in place mechanisms which ensure their ultimate substitution by renewable resources and conservation. The paper explores options for dealing with costing environmental externalities, particularly in relation to greenhouse emissions.

Jan 1, 1992