Search Documents

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

By Moinpour M

The kinetics of reduction of copper (cuprous) sulphide with CO-CO2-He gas mixtures, using an excess of CaO(s) as a sulphur-scavenging substance were investigated in the temperature range 855° - 950°C by a thermogravimetric method. Several gas compositions were employed at each temperature. Potential carbon deposition was overcome by preheating the reducing gas mixture. The phase-composition and the morphology of partially reactedsamples were analysed by a SEMlEDAX unit. The reduction rates showed strong dependence on the bulk gas compositions (CO, CO2) and, in most cases, the rate declined with rising temperature. The rate-controlling step appears to be the diffusion of CO2 gaseous species through the micropores of the CaS(s) - product layer which builds up around the CaOcore.

Jan 1, 1989

Paiam is a new township in the high mountains of Papua New Guinea built in association with the Porgera Joint Venture mine, one of the world's largest and most remote open cut gold mines. The Paiam town project is an interesting and genuine attempt at building sustainability into a community associated with a mine. A result of a tri-party agreement between a resource developer, government and land owners, this town is a good example of appropriate utilisation of benefits, obtained from resource development, directed at achieving a sustainable environment at local and regional levels.   Mining brought technology and income to the region, although as most mine staff fly directly in and out, local landowners considered there was a limited flow of benefits within the nearby townships. An agreement with government and mine was reached that more mine personnel and their families be housed locally. In 1998, we, a firm of Landscape Architects and Heritage Consultants based in Cairns, Queensland, were engaged to assist develop the fledgling town of Paiam into a livable and sustainable town and to produce material that would convey that information to stakeholders.   The design focused on establishing a sustainable town, with livability, urban form, aesthetics and opportunities for economic, social and cultural development. Aiming to be a livable town for locals and mine staff it included a market place designed as a focus for town life, essential for social cohesion and economic opportunities.   Located at 2200 m on steep rainforest clad topography, the town development has been laid out using an appropriate urban form based on organic village layouts. Clusters of houses allow for a common public area so children's play is monitored assisting with a sense of community similar to a traditional defensible village. Aesthetical consideration helps in developing community pride whilst maximising potential for development of a tourist industry.   Opportunities for ongoing economic development were incorporated in the design and construction process. These included developing skills and trades to service the region and to provide skills, development, income opportunities and infrastructure to last beyond mine closure. Administration procedures were set in place to form the basis of good governance.   The shift from traditional subsistence lifestyle to a sustainable community with traditional attributes was the project's goal and is being achieved.

Jun 1, 2010

By S Telford, J Weir

Heathgate Resources Pty Ltd (Heathgate) operates the Beverley Uranium Mine in South Australia, located on the plains between the northern Flinders Ranges and Lake Frome some 600 km north of the state capital Adelaide. The uranium orebody exists in permeable sands within the confined, highly saline Beverley aquifer, approximately 125 m below the ground surface and the uranium is mined using in situ recovery (ISR) technology. The Beverley mine is a highly technologically advanced ISR mine and is operated in accordance with stringent safety and environmental standards. The mine is currently licensed to export 1500 t of uranium oxide (U3O8) per annum. This paper outlines the fundamental differences between ISR operations and the more traditional uranium production methods, such as agitation leaching and heap leaching, where the ore is removed from the deposit, stockpiled, crushed, milled and leached on the surface. Solids tailings from either the mill or the heap are finally deposited in a tailing storage facility. ISR mining differs from conventional mining because the ore remains in place underground (in situ) and the groundwater contained in the ore-bearing aquifer is utilised as the mining fluid. This is achieved by drilling into the deposit and installing wells for extracting and re-injecting the groundwater which is fortified with chemicals. The fortified groundwater (ie mining fluid) flows through the permeable sands containing the orebody, dissolving the uranium. The pregnant mining fluid is then collected and transferred to the recovery plant where the uranium is captured (on ion exchange (IX) resin in the case of Beverley). The barren mining fluid is then re-fortified and recycled to the wellfields. Once mining is completed in a wellfield, the surface infrastructure is relocated to a new wellfield, and the mined-out wellfield is rehabilitated to its original surface condition. A comparison of 'standard' hydrometallurgical plants, heap leach and ISR shows a number of key differences, such as the rate of leaching, the level of control available to the operators, and the type of contact/reaction that occurs. While limited in its applications, ISR mining has proven successful at Beverley and provides another mining and processing method for the production of uranium.

Jan 1, 2008

By R L. Brathwaite

The mesothermal quartz-scheelite lodes of the Wakamarina valley are one of twelve known mined or prospected gold-bearing areas in the Marlborough Schist. Recorded production was 556 kg gold, a little silver, and c. 390 t scheelite. 134 m of the 1800 m long Golden Bar reef are accessible in the No 2 level of the Golden Bar mine. The reef is a typical multi-banded mesothermal vein, mostly c. 1.75 m wide, enclosing narrow horses of schist country rock. Scheelite is sparsely distributed, and is more common in small veinlets in the hanging wall schist. The country rocks are textural zone I-1m schists of prehnite-pumpellyite to pumpellyite-actinolite metamorphic facies. Their geochemistry suggests they are part of the Caples Terrane, and of calc-alkaline volcanogenic arc origin. The associated Wakamarina Quartzite is strongly recumbent folded, and of the same metamorphic grade, with abundant pumpellyite, stilpnomelane, and garnet, presumably spessartine. Although it has geochemical signatures of a deep sea sediment, it is depleted in Cr and Cu, and greatly enhanced in K and Ti, when compared with a standard chert. It also has trace element characteristics of a calc-alkaline arc-related sediment. However, associated greenschist has MORB-like incompatible element chemistry. The Golden Bar reef lies within a steeply dipping, normal to transtensional dip-slip fault adjacent to a shallow-dipping mylonite shear zone, which, at least on the footwall side, is 040 m wide. The shear foliation has been severely dragged down to nearly parallel the Golden Bar reef within 1 m of the quartz lode. Preliminary structural analysis suggests that the shear zone is extensional. X-ray diffraction analyses of the wall rocks show a progressive depletion of amphibole, stilpnomelane, and pumpellyite towards the reef, and enhanced illite/muscovite and Kfeldspar adjacent to the lode, along with possible graphitic carbon within 10m. Two zones of intense quartz veining occur, one adjacent to the hanging wall for 12 m and one from 40 m outwards. Quartz vein systems in the country rock are complex and span from pre-schistosity to post-mylonite. They include multiple generations of quartz, actinolite, stilpnomelane, pumpellyite, albite, adularia, chlorites, illite/muscovite, calcite, and scheelite. Metal analyses across the Golden Bar reef showed gold values of 0.13.1 ppm, and low tungsten values, consistent with the observed sporadic scheelite occurrences. As and Sb are at background levels, but enhanced Cr (150 - 430 ppm) relative to the schists (30 - 41 ppm) suggests that the source hydrothermal fluids passed through and leached mafic to ultramafic rocks.

Jan 1, 1994

Interest in mining narrow, vein-type ones has increased world-wide during the last few years despite the fact that prices of metals have not risen in proportion as production costs of mining, such as labour and energy. In many mines, where narrow ones are mined, the mining technique and equipment used have been poorly mechanised. The mining methods have been cut-and-fill or shrinkage stoping. Pneumatic jack-legs have been used for drilling and slushers have been used for loading. The methods that have been used can be called the 'first-generation' methods. Work has been very hard for miners. It has been dangerous and exhausting. Production volumes of mines, and a s a result of that, also profits have been low.

Jan 1, 1990

By R J. Holmes

An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and traded is crucial to effective resource utilisation, plant design, process optimisation and finally quality control to ensure that contract specifications are met. However, all too often the responsibility for sampling is entrusted to managers and personnel who do not fully appreciate the significance and importance of collecting representative samples for analysis, and everyone seems satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. This needs to change, because there is little point in accurately analysing samples if they are not representative in the first place. The resultant analyses can be next to meaningless and the effort taken to analyse such samples is to a large extent a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts. It is high time that sampling is given the attention it deserves as the first critical step in the quality measurement chain.CITATION:Holmes, R J, 2013. The importance of sampling in the mineral industry, in Proceedings MetPlant 2013 , pp 34-49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Larkin F, Farrer E, McGhie R. R

The Electrolytic Zinc Company of Australasia Limited commenced productive operations during February, 1936, at the- Rosebery and Hercules mines, which are situated near Rosebery, Tasmania. At this time it was decided that before re-organizing the steel sharpening shop a test should be made of the relative merits of conventional drill-steel and detachable bits. For this purpose Ingersoll-Rand type"I" thread centre hole.jackbits were selected and seventy-two of these were tested against conventional steel. Results indicated that, under the conditions pertaining at these mines, j ackbits should prove more economical than conventional drill-steel bits, and that a large-scale test, under working conditions, should be made. This was done by gradually replacing conventional drill-steel with jackbits at the Rosebery mine. Results were satisfactory and by the end of 1936 both mines were using only the jackbits.

Jan 1, 1939

At the treatment plant of the Broken Hill South Limited, Broken Hill, the zinc concentrates, with water, are pumped out to a more or less level area, and stored in dams to dry by drainage and evaporation.In-the construction of these dams a clay bank is first thrown up around the proposed dam site. The concentrate and water mixture are then run in from the perimeter, the solids being continuously shovelled up to increase the bank height, while the clear water is drained off at the centre and returned to the treatment plant.These dams vary in size up to 57,000 sq. ft. in area; when completed the banks are about 12 it. high, and the capacity for the largest dams is about 350,000 cub. ft., say, 20,000 tons.The survey office is called upon for a monthly survey of these dams, generally three of which are in process of building or refilling. The puggy nature of the material prohibits walking beyond the bank of the dam, therefore the following method of estimating concentrates was evolved. No originality is claimed, but as the need is for a true survey, and the results have shown the accuracy of the method, a description is warranted. The dam site is first laid out into 10-ft. squares with a theodoliteand 150-ft. steel tape, the outside lines being placed about 15 ft. from the clay bank - 15 ft. is the maximum convenient distance from the bank for working with the levelling staff mentioned later.As the dam is rarely rectangular in plan, the outside points pegged out are not always the corner of a square, but are placed to give the greatest convenience in later work, that is to say, there may be triangles and irregular figures. The plan (Fig. 1) and photographs (Figs. 5 and 6) will give the general idea of the layout. At each point is driven a 3 ft. 6 in. round iron peg about 3 ft. into the ground. This peg is to permanently mark the point, and is not liable to be...

Jan 1, 1925

By Cocquio D. S, Bauchau C

In the course of an integrated airborne survey in 1975, a uranium-molybdenum deposit was discovered by Minatome Australia Pty Limited in North Queensland, Australia, approximately 70 km by road west of Townsville.The mineralization occurs in a welded tuff unit within the Carboniferous St James Vokanics. It is structurally controlled by a complex of subvertical east-west fractures and is exposed over a strike length of 350 m. Drilling has traced a further 150 m extension underneath a barren capping consisting of a thick pile of vokano-sediments. The maximum width of the orebody is 150 m, and its vertical thickness is approximately 100 m.The primary ore minerals are coffinite, pitchblende and molybdenite, accompanied by various alteration products (particularly uranium molybdates).The vein-type mineralization is considered epigenetic.A comprehensive program of surface drilling and underground exploration is in progress to establish the uranium and molybdenum reserves.

Jan 1, 1980

The commercial development of the shallow (2200 ft2 400 ft) Windalia sand reservoir at Barrow Island provided the opportunity to conduct an intensive drilling programme using equipment and techniques designed for optimum performance.During the initial exploratory and reservoir delineation phase, 12 specific Windalia test wells were drilled using drilling equipment with an optimum depth range of 6QOO ft - 8000 ft and a 9 5/8 in by 7 in. casing programme was employed. The average time from commencement of move-in to rig release exclusive of coring for five representative wells was 187 hr during this phase.Development drilling commenced December 1966 with one rig, with the second in operation January 1967.As of January 1 1968, 168 development wells had been completed. The two rigs employed are drive-in units equipped with a telescoping .gelf raising doubles mast.Optimum depth range with 4 1/2 in. drill pipe is 2500-4000 ft. Casing programme is 8 5/8 in. by 5 1/2 in. Efficient performance was achieved immediately. The average time from commencement of move-in to rig release for 15 wells drilled early in the development programme was 99 hr.By application of experience and further modification of techniques, performance was improved to an average time of 72 hr per well for 15 wells recently completed.The major drilling problem on Barrow Island is surface hole drilling due to the very hard surface limestone combined with complete loss of circulation at sea level.In this operation, significant improvements have been effected. During the exploratory phase drilling, 12 1/4 in hole to set 9 5/8 in. casing, average penetration rate was 23 ft/hr. At the commencement of the development programme penetration rate, drilling 10 5/8 in. hole to set 8 5/8 in. casing, was 28 ft/hr for the 15 early wells considered, improving to 55 ft/hr for the 15 recent wells considered.This programme is a team effort and much credit must be given to the enthusiastic co-operation of the two drilling contractors.The current field record is 2 days 4 hr with a 4 1/2 hr move including the drilling of mousehole and rathole.

Jan 1, 1968

By Cadia Geology Team

The Cadia Hill Gold Mine, located near Orange in Central Western New South Wales, is owned and operated by Cadia Holdings Pty Ltd, a wholly owned subsidiary of Newcrest Mining Limited. Construction including pre-strip mining occurred from 1996 to 1998. The mine was officially opened in October 1998 following commissioning of the concentrator and mine fleet in June of that year. The Cadia Hill orebody is a porphyry related gold and copper system. The final pit has a strip ratio of approximately 1.3:1.0. Mining is undertaken on 15 metre benches using large capacity diesel hydraulic face shovels at an annualised rate of up to 70 Mtpa. The concentrator is currently rated at 17Mtpa and includes the worldÆs largest single line grinding circuit. The feasibility Mineral Resource was estimated at 352 Mt at 0.63 g/t Au and 0.17 per cent Cu. Initial reserves totalled 200 Mt at 0.74 g/t Au and 0.17 per cent Cu yielding a mine life of approximately 12 years. During the pre-production period mine geology systems were developed to support the operation. By design these systems were intended to add value to the business through minimisation of material miss-classification, provision of accurate and timely production information and mapping and reconciliation as a continuous model improvement tool. Variances that would prove to be material to the life of mine plan were recognised during the first year of production. These included identification of additional ore tonnes, higher copper grades and higher gold recoveries relative to the model. Gold grades and copper recoveries also reconciled favourably. Testwork was undertaken to determine the underlying causes of each variance. Re-modelling was then undertaken to capitalise on those variances. The Cadia Hill Gold Mine life of mine plan was re-evaluated with updated geology, grade, geotechnical, metallurgical and environmental inputs. Operating strategies were also reviewed and revised. Despite application of reduced metal prices in the evaluation, the outcome was one of extended mine life with more metal produced at lower cost. Development of robust mine geology systems, including a pro-active reconciliation process contributed to tangible improvement of the Cadia Hill Gold Mine operation. On-going system development and improvement initiatives are planned to add further value for the future.

Jan 1, 2000

Geological hazards such as faulting, basement ridges, and zones of "thin" (< 6 m) coal have a major impact on mining economics of underground operations in Huntly Coalfield. Experience has shown that drillhole-based investigations do not yield sufficiently detailed models of the coal seam to allow management of the planning risks associated with these hazards. Consequently, operational performance is affected by unplanned costs associated with lower productivity, loss of coal reserves, and expensive strata control remedies in problem ground conditions. Huntly Coalfield is a challenging environment for acquisition of good quality seismic reflection data due to the very thick (10-85m) weathering layer. Since 1994, successful acquisition of 2D and 3D data has been achieved through a combination of careful testing of technical parameters and experimental trials prior to committing to production recording. High resolution seismic reflection (HRSR) is proving to be an investigations technique which generates accurate and reliable models of the coal seam and associated structures, such as normal faults and topography of the surface on which the coal seam rests. The HRSR technique has been applied and developed in the Okowhao Sector where Huntly East Mine is developing and extracting coal reserves. Results of a recent 3D survey demonstrate that this technique is capable of revolutionising risk management in mine planning for underground mines in structurally complicated coal deposits.

Jan 1, 1997

By McLennan R. G

The principle of personal safety is as old as the human race. The application of this principle to industry is of much more recent origin, and may be said to be almost exclusively the product of the twentieth century. The enormous strides in technique and production mode prior to the turn of the century had been achieved without any real regard for the crippled human by-products of that expansive era. It was accepted that. accidents were inevitable and formed part of the price that must be paid for production. It was not until 1885 that the first Workmen's Compensation Act was passed in Germany making the employer financially liable for injuries suffered on his plant.With awakening social conscience came the first organised efforts to reduce accidents in industry. Early 19th century literature dealing with the development of powerdriven machinery and the growth of industry in Europe contains many references to the unsafe and unhealthy working conditions that accompanied the change-over from the home workshop to the industrial plant. By the year 1900, there were in Germany - and a little later in England governmental regulations dealing with the guarding of hazardous machinery. American industry, now the acknowledged leader in industrial safety, admits freely that when an organised safety movement commenced in that country, there was already a considerable amount of information available to them from European experience. The steel industry was well to the fore in this work, and in...

Jan 1, 1957

By M Rattenbur, A B. Christie, S C. Cox

A new minerals initiative to increase the level of understanding of New Zealand's mineral resources and to promote the development of minerals began earlier in the year in a partnership pilot-project between Crown Minerals and the Institute for Geological and Nuclear Sciences (GNS). The project aims to gather a set of comprehensive geoscientific data and build a series of digital GIS packages to highlight New Zealand's mineral prospectivity. The pilot study was carried out at a regional scale, and is focussed on mesothermal gold mineralisation in the South Island. A significant amount of geological data and information was sourced from open file technical reports held by Crown Minerals and from various databases held by GNS and has now been compiled into a single GIS dataset, which will soon be made freely available to interested parties. In addition to this comprehensive data compilation, prospectivity modelling using Weights of Evidence techniques was undertaken to highlight those areas likely to contain ore deposits. It is clear from this study that the South Island of New Zealand remains highly prospective for mesothermal gold mineralisation. Many of the highly prospective areas, which also contain historic mine workings, remain open for exploration. The study not only highlights these areas, but also other areas where the potential for similar mineralisation exists, in all likelihood with no surface expression. The study has also highlighted the value of many of the open-file technical reports held by Crown Minerals and the need to carry out additional studies using this and other available data at a more detailed level, possibly as the basis for a web-based minerals information system.

Jan 1, 2002

In the Broken Hill South mine tile practice of issuing to the miner a quantity of fuse and a box of caps from which he made up the "rods" required for a particular blast, has been abandoned. Instead, capping stations have been established, and the miner can now obtain, from the magazines, fuses cut to accurate lengths with the detonators attached.Various types of fuse-cutting machines and crimping devices are available, but only those used by the Broken Hill South Mine Ltd. are described in this paper.The fuse-cutting machine, designed by the engineering staff, is an electrically driven unit fitted with a gear box for the purpose of adjusting the rate at which the fuse is fed to the cutting device, thereby enabling fuses of various lengths to be accurately severed from the main coil of fuse.The machine in question is designed to cut 4, 6, and 8-ft. fuses, but no difficulty should be experienced in designing a machine to cut fuses to any required lengths.

Jan 1, 1932

By D A. Vogel

"Sampling may be mandatory for safety or environmental reasons. It may be because the value of a sale needs to be determined or to provide important data for investments. Whatever the reason, an incorrect sample will come at a risk. Only the person that relies on sampling data can imagine what the potential cost of such risk is.Sampling itself has a cost too; the direct cost of a quality control department and indirect cost for interrupting a process, such as stopping a conveyor belt during loading. If all material is the same then only one small sample is enough. But if all the material is different, then a very large sample must be tested; in the conveyor belt scenario it must be stopped very frequently and the associated cost will be high.A good sampling plan finds the proper balance between risk and cost. A good sample must be small enough to handle yet large enough to be representative for what information is required. All good samples have three things in common: there was proper access to the material the sampling tool allowed equal probability of particles being selected nothing was disregarded, everything was included.This too is the core of Gy’s ideal sampling scenario, where all particles have the same probability of being selected and included in the sample. There is risk of bias when part of a lot is excluded from the sample. Extra care is needed when sampling particularly heterogeneous, segregated or layered materials. The sampling tool should never systematically leave out a portion; it shall not push aside large or hard particles. Wet samples shall not stick to the sampling tool. This extends to sample preparation too when reducing particle size and dividing the sample in the process.CITATION:Vogel, D A, 2017. Access, select, include – a review of the commercial sampling of traded bulk commodities in the context of Gy’s Theory of Sampling, in Proceedings Eighth World Conference on Sampling and Blending, pp 367–378 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By S R. La Brooy, T Giraudo, I C. Ritchie

The treatment plant at the Macraes Gold Project in New Zealand processes a carbonaceous, refractory sulphide gold ore. Since its commissioning in 1990, there has been a programme of continuous improvement of the plant, leading to higher recovery, increased throughput and low operating costs. During this time, a number of processes for treating both, or either, the preg-robbing carbonaceous fraction of the ore and the refractory sulfide fraction have been evaluated, trialed and utilised. The latest phase involves the installation by Minproc of plant utilising Newmont Gold's Pressure Oxidation Technology, a process which is anticipated to mitigate both problem factors when commissioned in 1999.

Jan 1, 1998

By J Widjaja, E Hermawan, M Muharam, L Damanik

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The island of Java lies within the Sunda-Banda magmatic arc, which is characterised by multiple phases of volcanic activity and extensive compressional deformation. Along this zone, significant gold and copper mineralisation occurs, including some of the world’s largest deposits. In West Java, epithermal gold mineralisation is typically located in a series of extensional and strike-slip faults that cut Miocene to Pliocene volcanic rocks. These are all low-sulfidation, epithermal, vein-stockwork-style deposits developed in Miocene to Pliocene calc-alkaline volcanic rocks, which have been intruded by shallow-level plutons.This paper discusses an example of epithermal mineralisation at Mt Subang, West Java. Gold mineralisation was originally identified from stream sediment, panned concentrate and rock geochemistry sampling in the early 1990s. Geophysical surveys (magnetics and induced polarisation resistivity/chargeability), trenching, pitting and diamond hole drilling has subsequently revealed silicified-quartz vein epithermal gold mineralisation hosted within fault structures. It is clear that these structures acted as hydrothermal fluid pathways leading to the development of mineralised offshoots along north–south extensional and en-echelon arrays of north-east–south-west and transtensional faults. A number of vertical offshoots also occur in flexures and fault jogs. Post-mineral faulting has subsequently dissected and offset a number of the offshoots. Therefore, a detailed knowledge of structure and fault kinematics and displacement magnitudes is required in order to understand the geometry and continuity of mineralisation across major structures and maximise the resource potential. A range of exploration targets were modelled, indicating a minimum and maximum of 0.2 and 1.8 Moz of gold respectively.CITATION:Cunningham, M J M, Muharam, M, Damanik, L, Hermawan, E and Widjaja, J, 2015. Structural controls on the localisation of low-sulfidation epithermal mineralisation in West Java, Indonesia , in Proceedings PACRIM 2015 Congress, pp 227–234 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The Wamum and Idzan Creeks Prospect, located 79km W of Lae, Morobe Province, Papua New Guinea (PNG) was discovered by the exploration arm of Conzinc Riotinto of Australia Pty Ltd (CRAE). The detailed surface exploration and 11 vertical holes drilled by CRAE, combined with the recent work by Highlands Gold Limited, indicate the occurrence of porphyry copper-gold mineral- isation and associated alteration. The prospect occurs within andesitic volcanics of the Middle Miocene Langimar Beds. It is bounded by NE trending faults to the NW and SE. The alteration and mineral- isation is hosted in the andesitic tuffs adjacent to high level quartz diorite and hornblende diorite stocks. A NW trend to alteration and mineralisation is obvious in Wamum and Idzan Creeks. The main alteration type is propylitic with minor zones of potassic alteration. A late sericite-quartz-kaolinite-pyrite alteration overprinted the earlier alteration and mineralisation. Copper and gold mineralisation is related to a quartz-carbonate-chalcopyr-ite-pyrite (¦ bornite) vein stockwork and biotite ¦ K-feldspar alteration. The mineralisation system at Wamum and Idzan creeks is low in total sulphides. It is considered as a high- level fracture-controlled system with limited low grade Cu-Au mineralisation.

Jan 1, 1991