Search Documents

By P Aguilera, C Guerrero, M Tucker

With the advent of Electronic Detonator Systems in the global mining industry, as well as the development of high precision pyrotechnic delays, the measurement and analysis of delay performance (usually measured in terms of dispersion about a batch mean û precision, and the deviation of that mean from the nominal detonation time û accuracy), has become an important issue. Through the non-conventional use of existing Velocity of Detonation (VoD) measurement technology, it has been shown to be feasible to measure the precision and accuracy of delay detonator series connected in the same manner as a typical open pit bench hook up. This paper describes the work undertaken to compare and contrast performance results obtained using a range of instrumentation including High Speed Video (HSV) filming, digital counter timing using a Hewlett Packard Universal Counter and a digital VoD measurement device. The results obtained demonstrated the practical feasibility of using the latter technology in order to obtain relatively large amounts of data in a time-efficient manner, with a precision of better than 0.5 microseconds, if required. The results also confirmed the close statistical agreement obtained between the three forms of performance measurement, therefore permitting the substitution of the VoD measurement technique for the more capital cost intensive HSV technique and the slow, sample-by-sample HP Universal Counter method. This paper describes the methodology applied and the results obtained.

Jan 1, 2004

By B Lumsden, R Smiles

Independence Group’s Jaguar Mine treats a polymetallic ore producing a copper concentrate and zinc concentrate. Effective separation of the sulfides requires relatively fine grinding with flotation feed P80 of about 75µm. Zn losses to final tails are greater than 60 per cent and <32 µm. When magnetic conditioning was first installed in 2010 it showed about an 8 per cent reduction of zinc in final tail and on some ores a similar benefit for silver as well. Current testwork is showing about a 12 per cent reduction in zinc and silver in final tail, consistent with the original testwork. Sizing of the final tail during the tests showed that the reduction of zinc and silver losses were only in the <32 µm fraction, as would be expected from an aggregation process. However, the most surprising result was about a 4 per cent reduction in zinc and silver in the plant feed with a >99 per cent statistical certainty. The reduction in zinc and silver in the feed is also only in the <32 µm fraction. Therefore, because the magnetic conditioning of Zn flotation feed cannot impact plant ore feed grade the hypothesis is that the magnetic conditioning is reducing the fine mineral from downstream processes, like filtering and thickening, returning to the plant feed in the recycled process water. This hypothesis is consistent with plant observation of dirty concentrate thickener overflow and measurements of solids in the overflow, as well as the average % Zn grade in cyclone overflow that correlates with the magnetic conditioning ON and OFF days. This paper presents these plant test results.CITATION:Smiles, R and Lumsden, B, 2018. Improving fine sulfide mineral recovery in Independence Group’s Jaguar Mine zinc circuit, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M Rauer

With a worldwide growing population the demand for higher living standards, food and the development of new technology is rapidly rising. To allow for a continuous growth, larger quantities of minerals and raw materials are needed at a faster pace. Different methods have been developed to access or tap ore more quickly, such as improved drill and blast operations, mechanical mining methods using equipment such as roadheaders (RH), longwall miners and other technical equipment. Another possibility to access and develop mines faster is the use of a tunnel boring machine (TBM).The historical usage of TBMs is surprisingly long, but the opportunity for technology adoption by the majority of worldwide mining companies remains largely untapped. Dozens of full face TBMs have been used by mines around the world, including two that will begin operation soon in Australia. TBMs have been used to safely and rapidly gain access to the orebody, or to expand access to the orebody to increase output by running a TBM along the edge of the orebody for several kilometres. These machines have also been used for ventilation and for conveyor tunnels for ore removal. They have been used to quickly excavate long and winding declines giving access to an orebody at several levels in a short period of time.Tunnel boring technology can be used for mine declines, mine access tunnels and all sorts of different mine designs and set-ups. TBM technology simply needs to be adapted to the mine conditions and, if manufacturers are involved early on in the planning process for mine development, the operation can be very successful. In some cases, historically typical mine designs may need to be re-thought.One mine, the Stillwater Platinum mine in Nye, Montana, is currently employing its fourth TBM in 25 years. Two were used to create tunnels running alongside the orebody, rapidly expanding access to the orebody in many locations for increased output. Two were used to create parallel access tunnels to a mine expansion at the East Boulder orebody; one tunnel is for conveyor haulage and the other for vehicular access. TBMs have been employed successfully many times to rapidly drive vehicular decline tunnels to multiple mine levels, such as at the San Manuel – Magma Copper mine in the USA. While TBM technology may not seem to be optimal for every mine, these success stories show that the method can provide vast benefits for the right projects.Early use of TBMs in extremely hard rock metal mines, in the 1960s and 1970s, had limited success since performance was low. However there have been great improvements made over the years in the strength of rock which can be excavated by TBMs with high performance. Other important improvements involve the provision of a safe work environment, safely and rapidly supporting the rock and predicting geology ahead of the TBM.This paper will briefly note the more than 20 TBM mining projects and highlight some notable successes. It will then go on to give a status report on the two active TBM mining projects in Australia and the difference between a TBM operation versus other excavation methods such as drill and blast (D&B) or RH excavation.CITATION:Rauer, M, 2014. Tunnel boring machines in mines – a?brief review of past use with a status report on use today in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 663–670 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Lithocaps are potentially voluminous zones of advanced argillic and associated argillic alteration located above the subvolcanic intrusive environment. They constitute exploration objectives for epithermal and porphyry-type deposits. High-sulphidation epithermal deposits may be sought within lithocaps, whereas low-sulphidation deposits may exist on their edges. Porphyry Cu-Au/Au deposits may be accessible beneath lithocaps if systems are telescoped sufficiently. Oxidation of the basal, pyritic parts of lithocaps may promote supergene sulphide enrichment under appropriate tectonic and climatic conditions.

Jan 1, 1995

By D Jeffery, R Whittering, G Lane

Most aspects of process design are best addressed via bench scale or pilot plant scale test work. However, as experience is gained, fundamental or indicative data can provide more than adequate information to manage the risk associated with some process aspects of concentrator design.Historical precedence exists where minimal design test work has resulted in successful projects. On many occasions benchmarking, sometimes supported by fundamental data such as mineralogy, has been used to successfully develop effective process plant outcomes. Of course, this style of approach is most common with æfast trackÆ projects and often comes with the usual surprises that result from inadequate geometallurgy to define the project cash flow.This paper explores the risks and opportunities associated with the various facets of process development and design for a base metals concentrator. The paper is intended to provide guidance to project managers rather than address the technical aspects of process engineering.CITATION:Lane, G, Whittering, R and Jeffery, D, 2012. Benchmarking versus test work - How should you manage process risk?, in Proceedings Project Evaluation 2012 , pp 49-52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By G McCullough, J Els, J Bassan

Integrated Remote Operations Centres (IROCs) have a crucial role in optimising a mine’s carbon emissions, especially as industry faces an imperative to achieve net-zero emissions on an accelerated timeline. To meet this time pressure, operations must adopt a comprehensive approach to energy-related carbon management and history has proven that modern technologies cannot be simply bolted into existing operations. An IROC is the most dependable solution to enable a swift transition from strategy to operational tactics that support carbon optimisation. Achieving net-zero emissions requires addressing significant energy management challenges such as fleet electrification, integration of renewable energy sources and large-scale energy storage. These challenges demand a profound change in planning, managing and executing work at large operations. The key to overcoming these challenges is an integrated approach incorporating collaborative decision-making across the value chain and more sophisticated planning approaches. Additionally, closer integration with downstream processing offers opportunities for carbon optimisation across the value chain. This includes the ability to supply tailored products that meet more varied feed-requirements of customers transitioning to less carbon-intensive processes and developing collaborative decision-making across the entire steelmaking value chain (by incorporating steelmakers, transport, coal/natural-gas/hydrogen supply, energy supply and iron-ore supply). However, this requires significant improvement in collaborative maturity and integrated decision-making capability. Finally, the imperative to reduce carbon emission demands the introduction of a range of new technologies into existing operations. The new technologies will increase the operational complexity of the mines and IROCs will need to evolve capabilities to manage the increase complexity and support the effective operationalisation and integration of these new mining technologies. This paper outlines the new capabilities required and the role of IROCs in effective integration across the demand value chain. The focus is on building on the mining industries’ existing IROC experience and augmenting with processes, technologies and lessons from other industries.

Sep 18, 2023

By M Alston

Many organisations struggle to yield meaningful outcomes from incident investigations. This paper will demonstrate that we can discover systemic issues by rethinking the ‘Why’ and ‘How’ of investigations, fostering genuine risk reduction. Key points: 1. Shift from ‘prevent recurrence’ to ‘learn and reduce risk’: conventional investigations focus narrowly on recurrence prevention, resulting in narrowly focused investigations with limited ability to identify and reduce organisational risk. Redirecting our objective to learning and improvement opens avenues for broader risk mitigation. 2. Understanding daily work for risk insights: recognise that work is not always completed in full compliance with procedures. Workers will adapt how they complete tasks influenced by the conditions and management systems that exist every day. Understanding the conditions and systems affecting everyday work is vital for uncovering systemic risks. 3. Unearth systemic issues through in-depth exploration: many investigations address surface concerns such as lack of training, incorrect procedures, equipment not being maintained, and missing overarching organisational risks. Systemic, organisation-wide risks are not identified. To discover these systemic issues and create shared learnings, investigators must question management systems, including resourcing, planning and risk management. 4. Design actions for safe failure: common actions like discipline and training fall short and do not reduce risk. Resilience emerges from well-designed controls. Incorporate planning, better resources, interlocks, and guarding to bridge the gap between task execution and risk. 5. Investigation Reports as a Business Case: Investigation reports should not simply state historical information regarding an incident. They are to facilitate decision-making and be presented as a business case to drive change. Organisations can move beyond localised risk and ineffective administrative actions by changing investigation objectives and methods. They can facilitate learning, understand daily work intricacies, identify systemic issues, and enhance the capacity for safety, driving lasting risk reduction.

Apr 16, 2024

By X Li, R Chu, X Deng

The hot-dip galvanising industry is the largest consumer of zinc, with over 40 per cent of the world’s total annual production of zinc used for galvanised steel. The dross generated in the hot-dip galvanising coating process is a valuable co-product, since it contains high quantities of recyclable metal. A new method to recover the metal from the industrial galvanising dross was proposed using supergravity separation. During the hot-dip galvanising process, the presence of zinc dross has a serious impact on the surface quality of the hot-dip galvanised sheet, forming zinc dross defects. To reduce the impact of zinc dross, the zinc dross on the surface of the zinc pool needs to be manually or mechanically removed at regular intervals. However, during the dross removal process, a large amount of metal zinc is inevitably carried out, resulting in low zinc utilisation rate and high zinc loss rate. This article proposes an efficient and low-cost technology for the recycling and utilisation of hotdip galvanised dross, which uses super-gravity technology to recover hot-dip galvanised dross online. The metal in the hot-dip galvanised dross returns to the zinc pot in situ, while a small part of the dross remains in the super-gravity equipment, which can reduce the amount of zinc dross by more than 60 per cent and achieve a reduction in zinc loss from 17 per cent to less than 7 per cent.

Jun 19, 2024

By G Simpson, S Dressler, A E. Levett

Tailings storage facilities often represent a mining operation’s most significant liability, posing serious environmental, social and safety risks. Almost all mining operations dispose of wet tailings (Valenta et al, 2023), which represents a risk of failure due to the potential for a rapid strength reduction of the unconsolidated materials leading to static liquefaction and subsequent dam wall failure. As a waste stream, tailings disposal, decommissioning and relinquishment aim to be inexpensive processes, ruling out many highly engineered solutions. Advantageously, tailings consolidation does not need to be immediate, opening the door for relatively passive, inexpensive consolidation methods that aim to gradually increase the strength of tailings over extended periods (ie years). In this paper, we present the prospect of novel in situ tailings stabilisation, learning from studies that have investigated the most erosion-resistant landforms on Earth.

Aug 2, 2023

This study is to compare reinforcement of rebar and spiral bolts using laboratory pull-out test. For this purpose, the pull-out test was performed in laboratory for a curing period of 7- and 28-days. Based on the results of the laboratory pull-out test, the pull-out load of two support members rapidly increased with displacement until the breakpoint and then gently increased with displacement. The maximum pull-out load of spiral bolt was larger than that of rebar bolt. This implies that a spiral bolt is more stable than a rebar bolt for securing the stability of a ground or rock mass when a support was installed in a ground or rock mass under the same condition. In addition, the maximum external pressure of two support members increased with pull-out load and with displacement and the distribution of external pressure was commonly larger at the upper part than at the lower part of specimen. This indicates that the bond failure location by pull-out load should be mainly occurred at the surface portion of specimen. In conclusion, the reinforcing effect of a support depends on a curing period and a type of support member, and reinforcement of a spiral bolt is more effective than that of a rebar bolt.

Dec 6, 2010

By M Jahani, M Taji

For suitable production planning in an open pit mine, and also to carry out the optimisation process during the mining production cycle, prediction of fragment size distribution is required prior to carrying out the blasting operation. For this purpose, many prediction models, such as empirical models, were presented. The proficiency of these models differs in various conditions and mines. Therefore, in this paper the most important models, including SveDeFo, Kuz-Ram, CZM, Modified Kuz-Ram in 2005, Kuznestsov-Cunningham-Ouchterlony (KCO) and also Gheibie et al, were examined by the information of 20 blasts in Gol-Gohar iron ore mine. Fourteen images were taken on average for each blast. For image processing analysis Split-Desktop software was used. After examination, it was understood that none of the available empirical fragmentation models had presented acceptable performance, except the Kuz-Ram model for magnetite ore, which had somewhat acceptable results. However, this model for blasting patterns in hematite presented unsuitable results. Examination and comparison of two important distribution functions, Rosin-Rammler and Swebrec, were carried out and it was observed that the performance of Swebrec for fines was far better than Rosin-Rammler. This result for the upper part of fragment size distribution curve, coarse, is the reverse.CITATION:Jahani, M and Taji, M, 2015. Comparison of empirical fragmentation models at the Gol-Gohar iron ore mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 707–714 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Morley I. W

In the year 1926, Edie Creek, in the Morobe District of the Mandated Territory of New Guinea, saw the greatest gold rush of recent years. Situated 35 miles inland from the coast, and at an altitude of over 6000 feet, Edie Creek presented to the original prospectors a wet, jungle-clad uninhabited, and inhospitable region. There were no roads; and the only means of approach from the equally inhospitable coast was by an eight to ten days' tramp through coastal swamps and gorge-scarred mountains. All food supplies and equipment had to be carried on the backs of "kanakas," and in many cases through country occupied by hostile natives.Since the first discovery of payable gold at Edie Creek, mining on the Morobe Goldfield has shown remarkable progress, and in spite of the tremendous natural difficulties, the field today ranks as one of the most important in Australasia.Aeroplanes, more than any other factor, have been responsible for this rapid development. They provide the only means of transport from the coast, and at present serve the needs of over 600 Europeans and 3000 indentured native labourers engaged in the industry.

Jan 1, 1933

Integrated geological interpretation of aerial photographs and Landsat images revealed that the gold mineralisation at Kyauk Pahto took place in a narrow zone of tension fractures within part of a previously unrecognised dextral wrench fault system. The latter is the wider manifestation of the well known Sagaing (right-lateral) strike-slip fault which has a length of more than 1 000 km, and it demarcates the boundary between the Indo-Australian and Asian plates. A subtle, right-handed kink affects the full width of the Sagaing Wrench-fault System at about the latitude of Kyauk pahto, and the extra dilatancy imposed on the tension fracture zone facilitated episodic ingress of mineralising hydrothermal fluids by "seismic pumping".

Jan 1, 1987

Whilst employed by Dyno Nobel as the Technical Services Engineer û Brisbane, I was asked, as part of a contractual agreement, to look at optimising PioneerÆs blasting process to provide the most effective rock to the new crushing and screening plant. This paper details the preliminary blast designs and practices that have been in use at the quarry and the initial changes made to these designs, and the effect they have had on the excavation and crusher performance.

Jan 1, 1999

Potential hlghwaJl mining reserves in Australia are large, but geotechnical and operating conditions are quite different from those where highwall mining has evolved in the USA. In order to achieve safe and effective resource recovery, equipment and procedures should be developed to penetrate 250 m in the Australian mining environment. This paper identifies key auributes to be incorporated in such machinery and methodology. These suggestions are intended to promote discussion on innovations to satisfy Australian requirements for highly productive, safe and environmentally acceptable techniques.

Jan 1, 1993

By Ruschitzka C

The productivity and economic success of a German hard coal mine is attributed to the high productivity of a small number of operation points; however high rates of production are associated with increased gas emission at the working sites. Therefore modem high technology is required in order to reach the planned production rate, since high methane concentrations often cause unplanned breakdowns in operation. The optimised simulation of gas emission is a fundamental planning tool for mine design as well as for determining the potential of a coal deposit and has increased in significance over the last years. Methane-INFO enables the three-dimensional, graphical simulation of a working site taking account of different aspects such as the mine design, ventilation, production rate, geology, seam quality, gas exhaustion, etc. The following paper gives a short overview over the benefits of the discussed system.

Jan 1, 1995

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By A L. Bennett

It is well understood that designers and constructors must protect the existing surroundings of tunnel construction, particularly in the selection of excavation methods, ground support and waterproofing systems. However, while this can readily address the existing conditions, the tunnel owner and the designers need to consider the changes that are likely to occur during the life of the tunnel. It is typical for transport infrastructure to have a design life of at least a century. While the effects of constructing the tunnel on its surroundings are a short-term effect, the converse case, the protection of the tunnel, and the need to maintain its integrity, will affect developments over and adjacent to the tunnels beyond the foreseeable future. Decisions made during the design phase have the potential either to facilitate development or to hinder it for the long term.Examples principally from Australia, New Zealand, Singapore and Hong Kong show that the provision for future development is addressed in different ways. These have ranged from making no specific provision, putting the onus onto developers to ensure that the tunnels are not affected adversely, to including a loading allowance for future development in the performance specification or contract documents for a tunnel project.These two contrasting approaches have strong points and risks. A highly prescriptive definition of permissible loadings around the tunnel can provide unambiguous guidance for the approving authority and the developer, but runs the risk of being overly conservative to allow for all the envisaged works, while still missing a detrimental combination of effects that theoretically complies with the specified requirements. In contrast, a general requirement to not cause detriment is open to interpretation and potentially difficult negotiations to reach agreement between the tunnel owner/operator and developer and finally the appointed contractor (probably with no contractual relationship with the tunnel owner).In practice, a combination of prescriptive and performance requirements is likely to provide the optimum combination of clarity and flexibility. The author provides examples and recommendations on how such provisions could be structured.CITATION:Bennett, A L, 2014. Protection of ?tunnels in their future environment, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 495–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Q Zhou, J Pan, D Q. Zhu, C C. Yang

Oxidised pellets have become an indispensable high-quality charge for blast furnaces (BF) due to their uniform particle size, high iron grade, high mechanical strength, good metallurgical performance, as well as relatively low energy consumption and gaseous pollutant emissions in pellet production. Nevertheless, due to the rapid development of the global steel industry, highquality pellet feeds are becoming more and more scarce. In order to broaden the source of pellet feeds and reduce the production cost of pellets, more and more steel mills are going to use coarse iron ore fines with relatively low iron grade and low impurities for preparation of desirable pellet feeds through a typical wet grinding-settling-filtering process. In this work, the grinding, settling and filtering behaviour of Brazilian and Australian iron ore fines are studied and compared, aiming at finding out the internal relationship between the mineralogical characteristics of different iron ore types and their grinding-settling-filtering performance. The results show that the grindability is heavily dependent on the hardness of iron ores, which is governed by the mineralogical characteristics of the raw materials. Usually the higher the hardness, the more grinding energy is required. Except for Brazilian specularite, Australian hematite-goethite type iron ore fines and Brazilian hematite ore fines exhibit good grindability with a Bond Work Index of about 10–15 kW•h/t. In addition, the settling and filtering performance of ground iron ores are largely affected by the density, mineralogical characteristics of iron ore fines (eg, quantity of clay minerals and goethite and porosity of ore particles), grinding fineness, etc. Generally, iron ore fines with higher density, lower quantity of soft minerals (clay and goethite) and larger particle size give superior settling and filtering performance. For iron ore fines with inferior grinding, settling and filtering performance, applying more energy-efficient grinding techniques, blending with ore types with good settling and filtering performance can reduce grinding energy consumption and improve settling and filtration rates to maximise the productivity of equipment and lower the operational cost

Sep 18, 2023

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995