Search Documents

By Golding S. D, Price P. L

The Early Permian Aldebaran Sandstone is the main hydrocarbon reservoir in the Denison Trough. Contained hydrocarbon gas has a wet gas index (C1/CI - C4) of between 0.87 and 0.97 (N=10), and constituent methane has 813CPDB values ranging from -51.5 to -36.2% (N=10). These values clearly indicate that the gas is thermogenic rather than biogenic. Considering the predominantly humic nature and maturity of all organic source material for the gas, the methane 813C values are anomalously low, with typical values for humic methane present in natural gas formed at similar maturity levels significantly higher at -26 ¦ 5%o. This suggests that, in addition to disseminated organic matter in underlying marine mudrocks of the Cattle Creek Formation, methane substantially more depleted in 13C was derived from coal seams of the Reids Dome beds, a thick coal measure sequence which underlies the Cattle Creek Formation and, in the south, the Aldebaran Sandstone. This methane is likely to have S13C values of between -75 and -40 oo, based on the known isotopic composition of dry gas trapped in humic coals of similar rank in the Sydney Basin and elsewhere in the Bowen Basin. In addition to the low methane S13C values, the contribution of coal seam methane would explain the fact that, (1) methane S13C values do not show the normal increase with decreasing gas wetness, and (2)013C%o (ethane-methane) values do not show the expected decrease with decreasing gas wetness. The presence of co-existing, isotopically heavy CO2 (S13C = +2.0 to +3.4%0, N=3) in the Glentulloch and Merivale Fields is consistent with the view that natural gas in the Aldebaran Sandstone is in part coal seam derived.

Jan 1, 1991

Teleseismic travel time residuals measured on 600-1000 km seismic arrays across the Rio Grande and East African rifts provide evidence for upper mantle low velocity zones beneath each rift of velocity contrast 6%-8%. Refraction studies show thinning of the crust below the rift axes. Regional uplift which extends hundreds of km either side of the axes, is isostatically compensated by negative density contrast at depth. Since the refraction argues against compensation by thickened crust, compensation in the upper mantle low velocity zones is suggested. Temperature effects alone can not explain the reduced velocities. Generation of a few percent of partial melt is the most probable source of the reduction. A passive extensional mechanism is investigated for the Rio Grande rift in which hot asthenosphere intrudes the lithosphere raising its temperature and generating moderate melting. It requires less than 1% extension to explain the melting but a prodigious 26% to raise the temperature from a pre-rifting continental geotherm to the solidus. Geological estimates find that extension is less than 10% over the uplift zone. Such a mechanism is possible only if the prerifting lower lithosphere geotherm lies closer to the solidus than that of stable continent. This is supported by the observed high heat flow in the Rio Grande rift uplift region which, given the long time constant for thermal diffusion, reflects elevated temperatures at depth well in advance of the onset of rifting.

Jan 1, 1987

Lungfish and crayfish inhabit continental ecosystems similar to those of their ancient counterparts in the Permian (lungfish) and Triassic (crayfish) Periods, exhibiting similar burrowing behaviors to live, breed, and escape desiccation. Identification of their burrows in the geologic record when body fossils are absent has relied on the overall gross morphology of the burrows and the process of elimination. A method of burrow identification has been developed by evaluating burrow structures in an attempt to designate architectural and surficial burrow morphologies that uniquely reflect the distinctive burrowing mechanism of a particular organism. The information from this method defines the burrowing signatures of an organism, enabling the differentiation of their burrows even when fossil evidence is lacking.The lungfish constructed simple, vertical burrows with bulbous terminations. The burrow walls exhibit fine, horizontal to sub-horizontal striae and vertical to sub-vertical striae near the top of the bulbous terminus, reflecting a burrowing style similar to modern burrowing lungfish. The crayfish constructed simple, vertical burrows to complex burrows with multiple branching and chamber development. The burrow surface ornamentations exhibit horizontal to sub-horizontal ridges, vertical to sub-vertical groupings of scratches, mud- and lag-liners, knobby and hummocky textures, and body impressions, which reflect the burrowing mechanism of the crayfish.

Jan 1, 1990

By Xaykhamphoune, Ward B

Draglines have been used exclusively for primary overburden stripping at the German Creek Mine complex in central Queensland, where coal has been extracted from a series of ten open cut pits working seams of the German Creek Coal Measures. Due to the dip of the seams, most of the pits have now reached the limit of current economic viability and the emphasis has switched to underground extraction using longwall methods and to a new area of open cut reserves in the nearby Rangal Coal Measures at German Creek East. This area is characterised by weak Tertiary overburden, relatively steep dips and low strength intraformational shear planes at the top and bottom of the coal.The first pit, with a maximum depth to coal of 15 m at the low wall, avoided any major slope failure through use of scrapers to excavate the boxcut and dump the spoil away from the low wall. However, this method was not considered economically viable for the second pit where low wall depths reached 44 m. Following geotechnical investigations the boxcut was divided into a number of zones depending on depth of cover, dip and thickness of Tertiary clay. Slope stability was assessed for each zone using several analytical techniques to ensure that dragline mining would be acceptable. Slope design parameters incorporating various stabilisation techniques, notably an updip trench backfilled with competent spoil to form a low wall buttress prior to excavation of the boxcut panel, were successfully integrated into the mine plan after careful consideration of the complex scheduling to minimise rehandle.

Jan 1, 1992

The N3500 orebody is the northern continuation of the 3500 orebody at Xstrata Copper's Enterprise Mine and occurs at a depth of 1.3 to 1.8 km. At the nearby S3500 orebody, extreme deformation was observed in access drives where there was a high number of bedding planes per metre combined with either graphite or talc infill. The observed failure mechanism was largely controlled by the geometry of the inclined bedding submitted to high horizontal stresses. Due to the anisotropic strength and deformation behaviour of the shale rock mass, traditional isotropic methods of geomechanical property estimation based upon GSI are not appropriate. A numerical modelling approach, based upon the distinct element codes UDEC (2D) and 3DEC (3D), has been developed to accurately simulate the failure mechanisms and deformation observed in the initial infrastructure surrounding the N3500 orebody.

Nov 25, 2010

By Torabi S. R, Daly C. R

Wind blast is the sudden movement of air displaced by the massive collapse of roof rock in underground openings and is experienced as a high velocity flow of air through adjacent workings. The initial flow in the outbye direction is often followed by 'suck back', that is a reverse flow of air towards the newly created void. As part of the Wind Blast Project, undertaken by The University of New South Wales, Department of Mining Engineering, a physical model was constructed. One of the functions of the laboratory wind blast model is to provide insight into the dynamics of the interaction between the falling strata and the air being compressed below. During a collapse, some air is expelled into the surrounding roadways while the remainder penetrates towards the top of the roof elements. In this paper two aspects of the rock mass properties which influence the phenomenon are considered: - Flow paths through the falling roof element, ie the permeability of the roof element; - Bed separation prior to the fall which introduces a void above the roof element. A series of tests was carried out utilising the physical model in order to investigate the relationships between the flow of air through the simulated roadways, the variations in gauge pressure above and below the falling roof element, and the acceleration and terminal velocity of the latter, all as a function of the flow paths through the roof element and of the extent of the void above. The results of comprehensive tests using the wind blast physical model suggested that the time history of outbye air flow in the simulated roadway comprises two distinct phases. a) A primary phase, characterised by a high velocity flow of air which exhibits a peak and corresponds to the period during which the roof element is accelerating. The peak air velocity is related to the acceleration of the roof element. b) A secondary phase, characterised by a residual air flow of a lesser velocity than in the primary phase and corresponding to the period during which the roof element is falling at its terminal velocity. The velocity of the residual air flow is directly proportional to the terminal velocity of the roof element. In a monolithic collapse of a roof element it was shown that the presence of flow paths in the roof element increased the air velocity in the roadway in both the primary and the secondary phases. The presence of an air-filled void above the roof element, on the other hand, influenced the air velocity only in the primary phase by increasing the peak air velocity. The overall duration of the process was however decreased as a result. 'plug type' collapses, where roof failure extends to the ground surface, potentially generate the highest peak air velocities likely to be encountered during wind blasts.

Jan 1, 1995

By Hoffmann CF

Thermal conditions at depths of several k.i'-.r.,etres in hydrothermal systems are a major (actor controlling gold transport into the epithermal environment. Understanding of the coupling of thermal, metal and ligand (HZZ S) sources in the root zones of hydrothermal systems therefore becomes important for the application of tectonic and igneous petrochem- ical studies to regional scale precious metal exploration. The evaluation of favourable conditions in this source zone and application to explor- ation rests on a detailed knowledge of the gases, H2S, CO2 hydrocarbons and other trace components preserved in fluid inclusions. Recent developments in analytical techniques now permit examination of these components and the recognition of complex hydrocarbons in rluid inclusions from epithermal and other lydrothermal systems appears promising for ieoosit-source correlation.

Jan 1, 1987

One of the major changes in the resource industry in the nineties has been the re- internationalisation of the industry. The history of the resource business has been one of companies from the developed world utilising the cash flows from their operations to explore and develop mines in less developed regions of the world. This resource development has progressively generated wealth and economic development, which in tum, has led to a new generation of exploration and mining projects.   InSouth America, Chile had led the way in a mining resurgence, now closely followed by Argentina, Brazil, Venezuela and Peru. Although Chile has long had a significant copper mining industry, the pre-nationalisation phase was driven by American capital; the current phase has been spearheaded by RTZ - BHP at Escondida with Canadian junior companies, in particular, providing major speculative impetus. The Australian junior companies have not been significant in South America.   Although Canadian and USA exploration appears to be in decline, the mining industry, particularly in gold, is buoyant in North America. Interestingly, a number of listed and unlisted Australian companies are active, particularly in United States exploration.   Australian-based companies have dominated the South-East Asian exploration scene, especially in the Vietnam region. To date, the combination of political and legislative uncertainties have failed to lead to significant resource developments in this region. The area remains one of great potential, as exemplified by the exciting developments in Indonesia.   The Philippines has a history of mining, and this has been dominated by both local and North American operators. Both large and small Australian resource companies have a presence in the Philippines, and the development of the copper-gold potential could be impressive over the next decade.   The tales of the undeveloped mineral potential of China are probably rivalled only by the supposed strings of virgin Russian orebodies! Many Australian companies appear to have looked but few have chosen to proceed with Chinese developments. There seems little likelihood that China will, in the foreseeable future, rival South America as a target for Australian and North American resource capital.   Papua New Guinea has had an active, albeit chequered history in mining, with Australia long being the predominant source of exploration and development funds. The developing nation status of PNG has generated extreme uncertainty, with the current exploration scene all but dead. Most recently, the international flotation of Lihir Gold has tested the international and Australian investment community's commitment to PNG resource development.   The Australian exploration scene continues buoyant, although dominated by gold. The base metals scene is generating, on average, one significant base metal mine developed every couple of years. This is probably the fastest rate of significant base metal development in Australia's history.   The gold scene has been one of incredible dynamics, and there is no evidence that this momentum is waning. The development of new exploration techniques, together with a number of the companies reaching a critical size, has added to the momentum in the industry.

Jan 1, 1995

By A E. Petts

Record iron ore prices and a renaissance of infrastructure in the Pilbara have Flinders Mines poised to move from explorer/developer to an iron ore producer. The potential of the company’s Pilbara Iron Ore Project was first highlighted by the announcement of Rio Tinto’s Caliwingina North deposit to the north and the Fortescue Metals group’s Serenity deposit in the southeast. The success of Flinders Mines’ exploration has been based on incorporating landscape studies into an existing geological framework, and using this to understand the iron-rich materials that were emplaced during the Tertiary. The development of the Delta and Eagle deposit resource models highlights this process. There are three main mineralisation styles at the project; detrital iron, channel iron and bedded iron deposits. They have textural and mineralogical similarities with comparative deposits in the region. Gaining an insight into the geological processes unique to detrital iron deposits and more distal channel iron deposits has been important to understanding the geometallurgy of the mineralisation. The model sits comfortably with other regional oregenesis models and allows a contextual framework to be developed around the timing of deposition of the Fe-rich detritus and pisolitic nodules that dominate the deposits. The exploration model also allows Flinders to explore more effectively for bedded iron mineralisation developed prior to, and since the development of the Tertiary weathering landscape.

Jul 11, 2011

By L N. Loganathan

Risk exposure in tunnel projects is extremely high due to various factors such as variability of subsurface conditions, selection of inappropriate design and tunnelling methods, improper risk assessment on adjacent surface and subsurface structures and utilities, and inadequate contractual practices. The risks in tunnelling must be borne by the contractor, designer and the owner of a tunnelling project. There have been a number of improvements in the last ten to 15 years in the manner in which tunnel projects are developed and implemented in terms of their design, construction, financing and operations. One significant improvement has been the manner in which underground conditions and their risks are being managed. Owners are less willing to transfer the full responsibility to the contractor for managing the underground conditions, although this is a familiar manner in which underground major urban projects have been previously contracted and managed. The owners of tunnel projects in Singapore have advanced the risk management process for their projects through geotechnical interpretative baseline reports (GIBRs), geotechnical data reports (GDRs) and project specifications (PSs). This paper discusses industry practice and its development as well as the application during the preparation and use in Singapore on the Deep Tunnel Sewerage System (DTSS) and the Marina Coastal Expressway (MCE) project in Singapore. The DTSS trunk sewer is 48 km and ranges from 3.3 m to 6 m finished diameter up to 50 m below the ground. The underground conditions ranged from Old Alluvium, strengths of about 1 MPa to competent Bukit Tima granite, with strengths of over 230 MPa. The total route length of the MCE is about 5 km. About 3.6 km will be constructed underground, consisting of dual five-lane carriageways. The underground construction will be cut-and-cover, and 2.6 km will be constructed about 13 m underground, and 1 km of tunnel will range from 13 m to 24 m as the tunnel passes under a 420 m wide reach of Marina Bay, whose crossing will be constructed as a two-phase cofferdam.

Jan 1, 2008

The Charters Towers goldfield in northeastern Queensland produced over 206 tonnes of gold from gold-quartz veins hosted by Mid-Palaeozoic granodiorite, tonalite, diorite and to a lesser extent amphibolite-grade meta-sedimentary schist and meta-igneous rock. Mineralisation occurs in grouped, moderately dipping shear zones with altered wallrock rafts and a complex network of quartz veins.Over 75 per cent of the production came from three main vein systems in the central goldfield: the Brilliant, Day Dawn and Towers Hill vein systems.The Brilliant vein system is hosted by undeformed tonalite and contains north-plunging oreshoots on a north-dipping main fissure and on shorter east-dripping hangingwall fissures. The Day Dawn vein system is localised along a north-dipping dyke at the contact of two deformed granitoids in a brittly reactivated mylonite, where horizontal oreshoot plunges may be related to the original megascopic undulations in that structure. The Towers Hill vein system is hosted in two granodiorite types and has multiple ore controls.Structural analysis indicates that the distribution of the oreshoots within the vein systems is variously controlled by the primary fabric and igneous contacts of the granitoid host rocks. Splaying, changes in dip, and fissure intersections are the main controls. The largest vein systems are both in reactivated shallow-dipping mylonite, or in fissures in younger undeformed granitoids. Each vein system lies in a separate structural domain, usually where older east-striking structures are preserved.

Jan 1, 1990

By K Sommerville

BHP Billiton’s Area C iron ore operation has been in production since 2003. During 2010, below water table mining in the Marra Mamba formation commenced and dewatered ore has been successfully processed through the plant.The ability to mine below water table material increases reserves. Pits can be dewatered using a combination of ex-pit and in-pit bores. Critically it is important to allow suffi cient lead time to dewater. For Area C, in-pit bores yield the most water which presents challenges in every day operations when mining around bores. Operationally there are steep learning curves in obtaining equipment, training personnel and setting up infrastructure. Core risks include lifting, refuelling and maintaining gensets. The pipework, extraction and re-establishment work can be very manual.The challenges include blasting, mining, stockpiling, processing, water balance and disposal. Maximising up time on bores whilst minimising impacts to blast practices have evolved. Blast practices now align bores to the edge of patterns. Protecting bores have evolved from stemming bores with rock and re-drilling to using gas bags which require no drills. Based on moisture and material properties, mining of dewatered material can be categorised into three groups:1. normal,2. sheeting, and3. sheeting and top loading.Ore can go straight to the plant ore to drying pads where it takes between one and three months to drain.Stock management of these piles is important to ensure efficiency of the plant. Rules have been established for blending wet material to maintain feed capacity and some modifications to plants have been made. Dewatering of pits poses a challenge for water use. Initially turkey’s nests were established to capture water and use for dust suppression. As water abstraction has increased methods of management include using exhausted pits for storage and evaporators. Managed Aquifer recharge and use in potable water are being considered. An over arching coordination of the capacity and use are required.Important elements in dewatering include:• capacity models,• capital,• long to short planning,• day to day coordination, and • water level monitoring and balances. Success in dewatering requires a cross function team working towards a common goal. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By Coates D. F, Neil T. J, O&apos

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risks of slope fail- ure inherent in steeper slope angles. However, no formal framework for a proper analysis existed to date. This paper describes the results of the past four years' effort in which a formal eco- nomic analysis framework was developed and tested through a case study. This framework, in essence, consists of the availability of tested procedures and com- puter programs. The procedures as well as the programs are divided into two broad functional categories; (1) the first category related to assessing the economic benefits and costs associated with various pit slope angles and (2) the second category that determines the overall financial impact which the assessed benefits and costs exert to the mine operator's overall economic stature.

Jan 1, 1977

Over years of exploration the massive and tabular orebodies in the area to the South West of Western Areas Gold Mine had been assessed as containing about 50 million ounces of gold û a world class orebody. Planning initially was for a surface and subvertical shaft system to exploit this area but because of cost, a single lift shaft to an area which could be accessed ex Western Areas was planned to intersect the reef at 2760 metres. It was also planned to mine out the shaft pillar area long before the deep shafts would reach that position. This is not the normal practice in South African Gold Mines. The stoped out shaft pillar was backfilled to minimise movement in the shaft sites. The result of a competitive tender/adjudication process was that Cementation Mining û Skanska won and was awarded the R192 million contract to sink the Main and Ventilation Shafts on 15 June 1995. On 1 April 1999 Western Areas and Placer Dome SA formed a Joint Venture, which now owns and operates the mine on which the South Deep Shafts are situated. This situation prevails today.

Jan 1, 2002

By Cooke D, Large R

The Cambrian structure in the Mt Read Volcanics was produced by four deformational events: obduction of forearc-derived mafic/ultramalic complexes in the early Middle Cambrian, a middle Middle Cambrian extensional phase related to the post-collisional Mt Read volcanism and VHMS mineralisation, Middle Cambrian E-W folding, and Late Cambrian N-S folding and basin inversion. The major phase of VHMS mineralisation in western Tasmania is restricted to the very brief period of extensional tectonics within the middle Middle Cambrian. Within this period a N-S graben was produced with a complex series of transfer zones, largely striking E-W. Most VHMS mineralisation is restricted to the top of massive volcanic successions, with several mines close to Cambrian transfer structures. Many of the transfer structures continued to be active until the Devonian. The later compressional Cambrian events are not significant in localising orc formation. Within the Rosebery mine a complex pattern of minor Cambrian normal faults has a second order control on the distribution of the mineralisation.

Jan 1, 1997

The organisers of this function have suggested that this presentation should accomplish the following broad goals:set the technical tone for the conference to follow, implying some discussion of the æstate-of-the-artÆ of reserve estimation; and raise some current and common problems or deficiencies in our art in order to be thought provoking. As an engineer it is always easier to raise problems than to solve them with state-of-the-art. Consequently, I have had to limit the extensive list of problems that could have been discussed within this presentation. In regard to the state-of-the-art, this presentation will not be an esoteric discussion of the latest statistical estimation processes, although I intend to challenge those with skills in that area to address some of the thought provoking issues later on. The subtitle of the paper was established after reading an excerpt from æLife on the MississippiÆ by the American humorist Mark Twain in which Twain observed that the Mississippi River had become shorter during his working period on the River due to natural cut-offs and man made channels. Projecting into the future, he calculated that by now, Cairo, Missouri and New Orleans, Louisiana would become a single city with one mayor (the two cities are still separated by some 500 air miles). As a moral to this story Mark Twain observed that one can obtain: æwholesale returns of conjecture out of such a trifling investment of factÆ.

Jan 1, 2000

By B Washington, A Campbell, R Taylor

A sampling and measurement program was undertaken on the reaction shaft of the Olympic Dam copper flash smelting furnace. The object of the work was to provide information to validate a mathematical model of the burner and reaction shaft. Samples and measurements were undertaken through the burner inspection ports and the South East (SE) shaft sampling port about half way down the reaction shaft. Samples were collected to enable the calculation of particle loading of shaft gases, or sizing and chemical analysis of the partly-combusted feed, and the preparation of polished sections. Measurements were made of the temperature and sulfur dioxide content of the atmosphere, as well as plume velocity.To implement the program it was necessary to design and construct the following specialised items of equipment. For use at the burner inspection ports: a cup sampler for obtaining samples below the burners (temperature, solids loading and samples for characterisation).For use at the SE shaft sampling port and also at the settler level: trough sampler (plume definition and samples), isokinetic sampler (used as a velocity probe in this work), temperature probe (temperature traverses across the shaft), and sulfur dioxide probe (SO2 measurements across the shaft).The design of the sampling and measuring equipment is described, and examples are cited of the types of information obtained. The problems arising from working in a hot environment with molten or sticky particles are discussed.

Jan 1, 2005

By G M. Tranell, M Tangstad

The CO2 footprints in the production of Mn-ferroalloys and silicon/ferrosilicon are correlated with the fossil carbon consumption. The CO2 emissions may be reduced in the Mn-ferroalloy process by increasing the degree of prereduction and reduction of carbonate materials, while the silicon/ferrosilicon process is optimised based on silicon yield. By changing the fossil reductant into biogenic reductants, the global warming potential will be decreased even more. Even if the reductants are biogenic reductants, there will still be a global warming potential (GWP) in eg the electrode consumption and the CH4 emissions in the charcoal production. To reduce the use of fossil reductants there are also more disruptive technologies like the use of H2 that at least for the silicon production is on a very low technology readiness level (TRL). Using metallothermic processes will reduce the use of carbon but requires carbon neutral metal reductants. Electrowinning can have low CO2 emissions, and the electrowinning of pure Mn is a technology of high TRL. Salt and oxide electrolysis is under investigation for both Mn and Si production however the research is still on a low TRL. The use of CCS/CCU (carbon capture storage/utilisation) is a part of obtaining carbon neutral processes. Last, the energy mix used for these energy demanding processes is discussed.

Aug 21, 2024

By B BussiFre, J Molson, M Aubertin, G W. Wils

Waste rock piles containing reactive sulfide minerals can serve as long-term sources of acid mine drainage (AMD). Within these piles, many physical, geochemical and biological processes can contribute to the production of AMD. The flow of water, for example, depends on internal pile structure, which depends on the dumping methods used to construct the pile. In this paper, the internal structure and grain size distribution of typical waste rock piles are first reviewed with respect to their effect on internal water flow. A numerical model is then applied to simulate unsaturated flow within a waste pile assuming two primary waste materials, different atmospheric conditions and several geometric configurations. The simulations suggest that water movement can be controlled by introducing fine-grained material layers within the coarser host material. However, these layers should not be horizontal because they can lead to localised high-saturation regions as well as preferential flow favouring the production of AMD. A shallow slope towards the pile boundary may be introduced to force drainage to the outside while maintaining low saturation within the interior, thus reducing the production of AMD.

Jan 1, 2003

By P J. Howard, P Darvall, J H. Mainwaring

In less than a year, Atlas Iron’s Corunna Downs Project has moved from a new discovery to a substantial resource of high quality in an underexplored greenstone belt. Located approximately 170 km south-east of Port Hedland and 40 km south-west of Marble Bar, in the Pilbara Region of Western Australia, Atlas Iron Ltd (Atlas) has conducted extensive exploration work at Split Rock, Razorback, Runway and Shark Gully, consisting of geophysical surveying, field mapping, 464 reverse circulation and 16 diamond drill holes resulting in a current resource of 51 Mt at 57.3 per cent Fe (Atlas, 2014b).The Corunna Downs Project is interpreted to be hosted within the Cleaverville Formation of the Archaean Gorge Creek Group. Within the project area these rocks outcrop as subvertically dipping banded iron-formations (BIFs) and jaspilites, cherts, minor shales and meta-sediments forming a north–south trending plateau.Primary hematite-martite iron mineralisation is overprinted in the near surface environment by supergene goethite, and frequently capped with a thin laterite cover. The strongest enrichment areas have been discovered within topographic lows, proximal to fault zones, which coincide with a geophysical anolmaly. These characteristics were targeted, and the subsequent areas mapped in greater detail, allowing for efficient resource definition.Although first explored for iron in the late 1960s, it wasn’t until Atlas’ acquisition of the project in October 2012, that major strides were made to defining an economic resource. At present, Corunna Downs is Atlas’ best greenfields exploration discovery, both in terms of the potential scale of the resource and its blending capacity.The Corunna Downs prospect is emerging as a major new iron ore province in the Pilbara and includes 80 km of potential host stratigraphy. Corunna Downs sits strategically between Atlas’ Mt Webber and McPhee Creek tenements, and can play an important part in Atlas’ growth strategy as iron ore market conditions become more volatile and challenging.CITATION:Mainwaring, J H, Howard, P J and Darvall, P, 2015. Discovery of the Corunna Downs deposits, in Proceedings Iron Ore 2015, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015