Search Documents

By P J. Howard

Atlas Iron Limited’s McCamey’s North project lies at the eastern end of the Hamersley Basin, approximately 50 km east of Newman, Western Australia, and 3 km northeast of BHP Billiton’s Jimblebar Mine. The presence of significant surface iron mineralisation identified during field reconnaissance, has subsequently been further defined by detailed mapping and RC drilling.The project area is dominated by outcrops of moderate to steeply north and south dipping banded iron formation, cherts and shales of the Boolgeeda Iron Formation overlying rhyolites and rhyodacites of the Woongarra Volcanics. In lower lying areas recent colluvium and alluvium mask the Archaean geology. Drilling and downhole geophysics has allowed a composite stratigraphic section to be compiled through almost the entire Boolgeeda Iron Formation.Surface orientations and subsurface stratigraphic correlations using natural gamma logs indicate large scale open folding about east-west trending fold axes across the project area; while small scale tight to isoclinal folding with similar fold axis orientations are visible at the outcrop scale. These folds are cut by a number of moderate to steeply south-dipping normal faults defining a series of north-dipping fault blocks which repeat the stratigraphy across the project area.Bedded iron mineralisation consists mainly of haematite-martite and goethite ores with best results of 78 m @ 60.5 per cent Fe. Vitreous goethite is observed at the surface of the mineralised horizons. The mineralisation exhibits a strong stratigraphic control and extend down-dip up to 120 m below surface. The strike extent of the mineralisation is still to be determined. An inferred resource of 39 Mt at 58 per cent Fe has been defi ned to date (ASX: AGO 3 February 2011).The fi ndings at McCamey’s North indicate that there is potential for economic iron mineralisation to exist in other areas of Boolgeeda Iron Formation within the Hamersley Basin.

Jul 11, 2011

By C D. Rose

"The primary objective of this paper is to demonstrate a different approach to predicting and verifying mechanical sampling system precision. Early in the year 2011 an experiment was conducted to evaluate the sampling precision being obtained by a three-stage falling-stream mechanical sampling system for coal owned and operated by Peabody Energy. This system collects samples from lots averaging approximately 14000 t being loaded onto rail cars at a flow rate averaging about 9000 t/h. In phase 1 of the experiment, a total of 60 increments were collected in a two day period at preassigned intervals using a cross-belt sampler located on a conveyor belt feeding a silo upstream of the sampling system under evaluation. Coal variability parameters were calculated from the resulting laboratory analysis data using the gauge-invariant fractal model developed by the author.Estimates of precision of the three-stage system as a function of the number of increments were calculated using the variability parameters determined in phase 1. In phase 2 of the experiment, duplicate samples of 30 lots of coal were taken by the three-stage sampling system, enabling calculations of the precision being achieved by the system. Phase 2 precision estimates are in reasonable agreement with those of phase 1. Conclusions drawn from the experiment include the following: Experimental variograms or the equivalent correlograms are essential in understanding sampling issues and for designing a sampling system to meet specific precision requirements. Consensus coal sampling standards provided by ISO and ASTM may be improved by treating all stages of a mechanical sampling system as æsamplingÆ rather than considering downstream sampling stages as æsample preparationÆ, to be treated in a separate part of the document. The coal industry would profit from use of methodology for routinely monitoring the overall measurement precision and the precision of the individual components of measurement: sampling, sample preparation and laboratory testing. This would not only give necessary credence to the measurement results but would also no doubt, lead to more efficient sampling system designs.CITATION:Rose, C D, 2012. Evaluation of precision being obtained by a three-stage sampling system for coal, in Proceedings Sampling 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By N Cusworth, W R. Mackenzie

"In 2007, the authors presented a framework for the conduct of resource project feasibility studies and provided guidance on minimum standards and best practice (Mackenzie and Cusworth, 2007).This paper will present the authors’ observations in relation to feasibility studies undertaken to support investments made during the unprecedented period of resource project capital investment since 2007. It will also provide comments on general trends in the mining industry’s approach to project assessment and update recommendations on best practice.CITATION:Mackenzie, W R and Cusworth, N, 2016. The use and abuse of feasibility studies – has anything changed?, in Proceedings Project Evaluation 2016, pp 133–148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

In 1987 the control strategies at the then ZC Mines' New Broken Hill Consolidated concentrator were a miscellaneous mixture of computer hardware and technology for ISA, grinding and residue thickener control. Field instrumentation was based on current-to-air technology of approximately the 1960s. Decisions were made to rationalise computer and field instrumentation technologies; the object being to consolidate control loops into one system to enable expansion of the system to include all facets of plant operation. The first stage was to install a DEC Micro PDP 11/23 computer and serial line communication as recommended by AMDEL Ltd, for the ISA system, as discussed by Walsh and Freeman (1988). The second stage was to select and install a distributed control system for the centralisation of the control loops into one system, and to replace field instrumentation with state-of-the-art technology. This paper deals with the second stage of the rationalisation, in an attempt to give an insight into what is required when personnel are faced with such a decision, details of costs involved in keeping a system functioning and utilised; and the requirement to train personnel for acceptance of further control strategies.

Jan 1, 1991

The long-term outlook Tor Australla's traditional mining products is for flat demand and continuing low prices. This has come about because of three far-reaching changes since earlier boom days: 1. Continuing declines in intensity of usage of basic mine products; 2. The failure of newer western and third world developing countries to realise growth expectations; and 3. Continued production pressure from third world countries (and first-world primary producers) in an effort to earn foreign exchange and rectify trade balances. These trends have led to a general situation of excess supply and weak demand. In this environment, the prerequisites for survival in the mining sector are first-class mines, modern and efficient production methods, low unit costs, aggressive marketing, and products with reasonable operating margins. Many of Australia's mines meet these prerequisites. Following the A$ depreciation and widespread unit cost reductions, most of these mines will be moderately profitable at current depressed commodity prices. They are well placed to benefit from price rises if these eventuate. A new generation of mines is concentrating on a more profitable product range (gold, diamonds, uranium, mineral sands). Australia's balance of trade remains firmly dependent on the primary mining and agricultural industries (Fig. 1). Despite optimistic talk of high-tech developments, tourism and a resurgence of manufacturing, these will remain a small component of Australia's export structure.

Jan 1, 1987

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By S Khadhraoui, T Yusuf, C Kirmse, E Hecker, R Degel, A Akouch, N Borowski, M Reuter

For an optimal design and control of metallurgical processes, a deep understanding of the thermodynamics of the governing reactions is required. Modelling the thermochemical behaviour of those reactions is complex, as it involves multi-component and multi-phase systems. For this purpose, thermodynamic computing systems such as FactSage™ (Bale et al, 2016), which combine Gibbs energy minimisation routines with large databases of optimised thermodynamic data of solutions and compounds, have been used within the SMS group GmbH. Recently, the successful integration of those thermodynamic computing systems into the digital platforms of SMS has been achieved through ChemApp, which made running complex thermochemical calculations in Python-integrated development environments possible. ChemApp is a programmer’s package for thermochemistry and incorporates the Gibbs energy minimiser of FactSage™ as reported by Petersen and Hack (2007) as well as by Zietsman and Petersen (2018). The digital platforms link the fundamental and the industrial aspects together and can be applied as a process advisor, or for the evaluation of the environmental footprint and the economic implications of different process routes, as discussed by Reuter (2023). Two examples illustrating the progress of the developments in this regard will be introduced: 1. The Tilting Refining Furnace (TRF) for copper scrap recycling and refining to anode copper (the BlueControlApp). 2. Dephosphorisation control for the oxygen steelmaking process (Basic Oxygen Furnace (BOF)).

Jun 19, 2024

Recent legislation in the environmental field gives the mining industry an opportunity to take timely action to address its image. Shifting the focus away from mining (the activity) to minerals (the resource) will enable the mining industry to stand on equal footing with other industries and will help minimise the vulnerability to political and interest groupsÆ interference.

Jan 1, 1993

By J Pan, C M. Tang, D Q. Zhu, C C. Yang, S W. Li, Z Q. Guo

The short process of electric furnace steelmaking with direct reduction iron (DRI) as raw material is an important process for smelting high-quality and special steels. In order to prepare high-quality DRI, the pellets with basicity of natural basicity and 0.4 were prepared from magnetite concentrate (MR=0.09, MR=0.4) and hematite concentrate (HR=0.02, HR=0.4). Based on the HYL method, the gas-based direct reduction experiments were conducted under the condition of rich hydrogen (H2/CO = 2.6). The reduction index (RI), reduction swelling (RSI), cold compressive strength (CCS), and phase changes of the pellets were systematically studied. The results show that the RI of four kinds of pellets is greater than four in the temperature range of 800~950°C. For the magnetite pellets, at a fixed reduction temperature, the RSI increases and then gradually decreases, reaching a peak between 50 per cent and 80 per cent. Moreover, the RSI enhances with the increase of the reduction temperature. In general, the RI, RSI, and reduced CCS of the MR=0.09 pellets are better than those of the MR=0.4 pellets. For the hematite pellets, the maximum RSI decreases from 23 per cent to 17 per cent during hydrogen-rich reduction, while the compressive strength increases from 500 to 1070 Nꞏpellet-1. The main reason is that the glass phase generated by the increase of basicity adheres to the surface of hematite grains, hindering the contact between reducing gas and particles. As a result, the apparent activation energy is reduced, which is not conducive to the reduction process. In addition, the glassy phase attached to the hematite reduces the migration rate of Fe2+/Fe3+, resulting in a difference in the reduction expansion rate of hematite in the inner and outer layers of the pellet. Thus, concentric cracks are formed inside the pellets, the RSI increases and reduced CCS decreases.

Sep 18, 2023

By A I M Ritchie

The pyrite oxidation rate is a process central to both the performance of bio-oxidation heaps, used in the pre-treatment of some refractory gold ores, and to the levels of pollution in acid rock drainage (ARD) from pyritic waste rock dumps. A goal in bio-oxidation heaps is to achieve high oxidation rates in the heap as a whole. In comparison, one way to mitigate the environment impact of ARD, is to reduce the overall oxidation rate in the waste rock dump since pyrite oxidation is the primary pollutant generation process. In both bio-oxidation heaps and waste rock dumps the overall oxidation rate of the pyritic material (the intrinsic oxidation rate) at these sites. Much research has been conducted over the last 40 years or so on the oxidation rate of pyritic material with particular emphasis on the catalytic role played by bacteria. More recently mathematical models and field measurements have clarified the extent to which oxygen transport rates are rate limiting, what the dominant oxygen transport mechanisms are and the physical properties of the heaps which have most impact on these transport rates and on the overall oxidation rate. How the performance of bio-oxidation heaps can be optimised and how the pollution load in drainage from waste rock dumps depends on gas transport mechanisms is briefly reviewed. The sensitive of the overall oxidation rate in bio-oxidation heaps and waste rock dumps to details of the intrinsic oxidation rate is quantified.

Jan 1, 1994

By D Pilone

The Tyrrhenian micro-nodules, findable at low depths (200/600 m under s l) are a reasonable reserve of manganese. They can be easily and cheaply recovered but do not contain valuable metals as in the case of oceanic nodules. In this work a hydrometallurgical process for manganese recovery from Tyrrhenian nodules is presented. The studied treatment includes the following operations: magnetic enrichment, reducing leaching, leach liquor purification and electrowinning . The study shows that the most important step in the process is the preliminary manganese enrichment. It can be done directly on the platform reducing not only the transport cost, but also the residue mud in the metallurgical plant. The leaching parameters such as status and size of nodules, temperature, composition of leaching solution and S/L ratio have been investigated. After purifying the leach liquor by iron precipitation as ammonium jarosite , the conditions to electrowin manganese have been investigated. The yields of both manganese leaching and iron precipitation together with current efficiency and specific energy consumption in the electrowinning step are given.

Jan 1, 2000

Prefeasibility planning and cost estimation of conveyor systems has historically been undertaken by comparing fixed plant transport requirements to that of similar systems in service. This paper describes the development of a prefeasibility conveyor technical design and cost estimation application using Microsoft Excel Visual Basic for Applications (VBA) platform. The application tool known as D-Convey (Dachshund Convey) was developed with the goal enabling the end user:- to develop a technical model for conceptualised conveyor systems,- to perform economic analysis on the developed technical model, and - to conduct a comparative and risk analysis.An Excel VBA based platform was utilised to draw upon both the analytical and graphical capabilities of a spreadsheet. Some of the features of D-Convey system include a revolutionary dynamic graphical help system, known as the 'information pane' in lieu of traditional help files as well as the use of familiar graphical user interface elements such as the MS Office 2007 task ribbon. The D-Convey system incorporates material database allowing for mass handling prefeasibility estimation in other industries; it has been validated at a local quarry.

Dec 6, 2010

By J Rowland

"Ventilation models are invaluable tools for both prediction of routine daily ventilation changesin an operating mine to circuit performance expectations at the mine in 20 yearsÆ time. Arguably ventilation offi cers are becoming increasingly reliant on maintaining an accurate ventilation model with which to do their work. This paper relates to the practical assessment of the accuracy and thus ability of a mine site ventilation model to be reliably utilised on such varied tasks. The author's experience shows that in some cases the incumbent model is found to be in a state of tune that demonstrates a mine wide detailed assessment of branch resistances is simply not required. The money spent on a detailed mine wide ventilation survey that is not required would be far bett er served purchasing much needed monitoring equipment, rather than fixing something that is possibly not even broken. The term ænot rocket scienceÆ has been incorporated into the title of this paper because it appears that many practitioners believe that circuit validation is diffi cult. As long as clear att ention to detail is paid to the actual data collection process then drawing an accuracy comparison between the circuit performance and the model performance at any particular point in time, is really very simple. This paper will show a manner in which a circuit can be analysed to determine its actual state of health by using various diagnostic tools and tips. It will help ensure that subsequent work scopes to address any highlighted model defi ciencies can be more effi ciently scoped and targeted. It will hopefully remind operational people that such self assessments can easily be done æin houseÆ if the appropriate steps are followed."

Jun 1, 2012

Water Balancing in Mineral Processing - Issues and Opportunities

Sep 13, 2010

By C Adams

Reports of delays and cost blowouts in major study and construction projects are becoming increasingly prevalent in the resources industry. This is mainly being attributed to an escalating cost environment associated with the increased number of projects in the development to construction pipeline and a scarcity of competent skilled resources to deliver these projects. However, not all this effect can be directly attributed to the current environment. Historically the mining industry has not performed well in its ability to deliver projects according to the financial and physical parameters forecast in the feasibility study process. To manage the risks associated with delivery of major projects, resource companies need to ensure they use a standardised approach to management of their project development to satisfy project objectives and enable more efficient use of the increasingly limited available resources. Each discrete step in advancing the project from scoping study to operations needs to be integrated, reducing the amount of rework and duplication. This paper is primarily a consolidation of existing ideas on project management systems but also introduces new concepts to solve current issues. It describes the basic components of a typical mining project, the issues that commonly arise, the key attributes, and critical steps required for an effective integrated project management system covering projects from initial scoping studies through to project commissioning and operation. This paper focuses on technical study components of the mine development project with allowance for transitioning to design and construction and operation phases.

Jan 1, 2006

By Pati±o A

The Argentine pyroclastic loess arevulcanogenic deposits, which have their sources in the circumnpacific rim. The object of this work is to realize a de-tailed mineralogical characterization of this sediments, to use it like a geo logic outline which regiters discordance or similarity in them, The sampling zone extend from 714N-4125 to 622W-339S. The descriptions of these sediments was considered like basic, mesobasic or acid rocks. The basic sediments, looking like andesite-basaltic composition, are fill-ing the andean valley. The mesobasic one have a similar composition with a pyro-clastic dacite rock, and have been found in marshy pleistocene sediments in the intermountain valley and in the pampeana prairies. The acid ashed conform rhyoda-cite-rhyolite sediments which form the pampeana loess covers in the prairie.

Jan 1, 1990

By A M. Lechner, V Glenn, M Edraki, D R. Mulligan, C Unger

With more than 50 000 recorded abandoned mines in Australia, effective management strategies are needed to prioritise and manage health, safety, environmental and socio-economic risks and opportunities. This paper reviews international leading practices for abandoned mine management and identifies key issues that need to be addressed in the Australian context. As well as the academic literature, this review draws on a 2008 global legacy site survey and forum in 2008, a Churchill Fellowship study of abandoned mines and the recently released æStrategic Framework for Management of Abandoned Mines in the Minerals IndustryÆ (MCMPR/MCA, 2010).A conceptual model was developed to identify the relationship between key issues affecting the management of abandoned mines in Australia. The conceptual model is then used in the development of a maturity chart which draws on risk management principles to provide leading practice guidance for abandoned mine managers, jurisdictions and stakeholders. The maturity chart approach for risk management has been successfully used elsewhere to evaluate safety, environmental and socio-economic maturity.CITATION:Unger, C, Lechner, A M, Glenn, V, Edraki, M and Mulligan, D R, 2012. Mapping and prioritising rehabilitation of abandoned mines in Australia, in Proceedings Life-of-Mine 2012 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By V Chamberlain, M Appeah Owusu, M Aniawu-Asumakah, A Anyimadu, R Peattie

This is an integrated geology and plant improvement study arising from the heterogeneity seen in mineralogy and gold association at the Obuasi goldmine in Ghana. This heterogeneity comes from the two ore types mined, the one being a sulphide ore, mainly composed of gold-bearing arsenopyrites. This gold is refractory and exhibits a strong relationship between gold and As. The other is quartz veins, that are high grade and free milling. The installed circuit consists of comminution – Gravity -Flotation – BIOX – Leaching and Adsorption processes. The opportunity tested involved improved mass pull - related flotation recovery of Au in the Sulphide stream; while balancing the need for a minimum Sulphide grade for the Bio-oxidation process, occasioned by the removal of 25 to 30 % of the (quartz) stream through preconcentration by Ore sorting. The current circuit is then utilized for the sulphide route, while a smaller grind-gravity circuit is utilised for the quartz stream in a relatively inexpensive way, followed by a common leaching and adsorption circuit. Added advantages of the strategy includes faster recovery of gold from the quartz stream, with less consumption of reagents from saving on flotation and BIOX reagents for this stream. Screening and Ore sorting was successfully tested with laser technology, achieving over 98% separation of quarts (containing up to 40% of the gold). The plant schedule of Ore, the suggested circuit design for the Ore sorting, the results obtained from the different flotation regimes, as well as consequent financial modelling have been presented and discussed in this paper. This illustrates the opportunity that arises out of a detailed analysis of material versus installed circuits, even if the gains in pre-concentration do not necessarily involve rejection of gangue material. An added opportunity for future investigation, briefly discussed but not tested in this paper, would be to maintain current mass pulls but with increase in throughput (by the space created by the sorted material). This will of course require the mining ability. It could also add LOM value by altering the cut-off grade.

Nov 10, 2020

This paper is a collection of thoughts and frameworks. It addresses a simple question: æIf we are to believe the large number of people and institutions indicating that humans are destroying the Earth and that the end is nigh, why do we bother trying to be sustainable?Æ The paper lays out evidence for the existence of multiple hazards to global society. The existence of a hazard alone is insufficient to make an assessment of risk. Risk estimates are required to support decision-making. An approach to assessing risk is provided and some limited data are presented. A new ædefinitionÆ or statement of what sustainability (in a broad sense) might have become is then given. A decision framework for guiding decision- making about the risks is developed. This framework includes a definition of leadership with inherent implications for what determines whether a leadership position by title is actually leading. The paper concludes by offering a view of minerals industry sustainability and considerations around maturity in the current economic situation. It is hoped that by placing this collection of frameworks around sustainability, a supporting structure emerges that will facilitate action. It is proposed that action taken in this way will be more effective than reaction to regulation or even social license to operate imperatives because it is driven by a more holistic view of the challenges and the potential roles of individuals û all of whom are potential leaders at some scale of action.

Jan 1, 2009