Search Documents

By A V. Ozsever

The selectivity in flotation columns involving the separation of particles of varying degrees of floatability is based on differential flotation rates in the collection zone, reflux action between the froth and collection zones, and differential detachment rates in the froth zone. Using well known theoretical models describing the separation process and experimental data, froth zone and overall flotation recovery values were quantified for particles in an anthracite coal that have a wide range of floatability potential. For highly floatable particles, froth recovery had a very minimal impact on overall recovery while the recovery of weakly floatable material was decreased substantially by reductions in froth recovery values. In addition, under carrying-capacity limiting conditions, selectivity was enhanced by the preferential detachment of the weakly floatable material. Based on this concept, highly floatable material was added directly into the froth zone when treating the anthracite coal. The enriched froth phase reduced the product ash content of the anthracite product by five absolute percentage points while maintaining a constant recovery value.

Jan 1, 2005

By I Ritchie, A Johnston, D Yataco

Marcobre SAC (Marcobre) is developing the Mina Justa copper mine project, located in the Ica region of Peru. The Mina Justa IOCG orebody comprises of a sulfide mass overlain by an oxide cap with a sharp transitional zone between the sulfide and oxide masses. The primary target metal is copper, but there are minor amounts of gold and silver. The oxide will be treated by HPGR, crushing and vat leaching, whereas the sulfide will be treated by HPGR, milling and froth flotation. The processing selections are due to some unusual ore characteristics which have required relatively unconventional solutions.Vat leaching was chosen over heap leaching and other processes after detailed trade-off studies found it to be the most attractive, primarily due to the high acid consumption of the ore. The sulfide flotation produces a wide range of concentrate grades due to the complex nature of the mineralogy. The selection of HPGR circuits for both the oxide and sulfide ore is due to the extremely hard and competent nature of the deposit. These factors and others have contributed to a unique process selection for this resource.The selection process for the oxide and sulfide ores, and an overview of the technology, equipment selection and geometallurgy, will be discussed.CITATION:Johnston, A, Ritchie, I and Yataco, D, 2017. Process development for the Mina Justa project, in Proceedings MetPlant 2017, pp 207–217 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By A Fitzpatrick

An integrated and dynamic water balance and water quality model for a proposed base metal mine has been created using the GoldSimÖ software package. The model was initially developed to address the water quality of the Tailings Management Facility pond and how pond discharge would potentially affect downstream water quality. However, due to changing project objectives, the modelling has expanded over time through an iterative process to encompass the full mine site and all receiving environment water quality. The model results have been used as part of the mine planning/design process but are also intended to be used for the environmental impact assessment and permitting process. The model has been built to allow for changes to input terms to be readily made as additional data becomes available. The model results serve as a prediction of water quality and the potential project impacts to the receiving environment water quality. This paper presents the process by which data from a wide variety of sources was used to construct the model and how the model results were used to guide development of a conceptual water management plan. In addition, the role of the model in establishing proposed discharge criteria will be highlighted. The model has been delivered as a fully functional application with the intent that the end-user can be other than the modeller, the development of this aspect shall also be covered. CITATION:Fitzpatrick, A, 2012. Predictive site-wide water quality modelling as a tool for mine planning and permitting - A recent Canadian example, in Proceedings Life-of-Mine 2012 , pp 71-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Dean J. A, Taube A, White A. H, Messenger P. R, Jones I. W O, Huston D. L

The 50 million tonne Mount Morgan gold-copper deposit (4.99 g/t Au, 0.72 per cent Cu) was an irregular pipe-like body of quartz and pyrite, with subordinate chalcopyrite, magnetite and gold. Mineralisation was hosted by the Middle Devonian Mine Corridor Volcanics which occur as a roof pendant within the Late Devonian Mount Morgan Tonalite. On three sides, the deposit was enclosed by a series of normal, concave, listric faults and surrounded by outward-dipping Mine Corridor Volcanics. The tonalite which bounded the western side of the deposit transgresses the domal structure with no apparent interference. A pipe of intense, texturally-destructive, quartz-sericite-chlorite ¦ pyrite underlay and partly surrounded the deposit.The volcanic setting of the deposit, its shape, metal content and associated footwall alteration are consistent with a subsea-floor replacement origin for the gold-copper mineralisation. Mineralogical studies have confirmed the deposit has been recrystallised and annealed by a thermal metamorphic event, most likely the intrusion of the Mount Morgan Tonalite. Pyrrhotite Pipe mineralisation replaces annealed massive pyrite, suggesting that it formed during retrogressive metasomatism associated with tonalite emplacement. Telluride minerals have a close association with chalcopyrite, and no evidence for a late telluride paragenetic stage was observed. Telluride mineralisation is inferred to be genetically related to the massive sulphide mineralisation, and a separate magmatogenic origin for this mineralisation is discounted.

Jan 1, 1993

By J J. Eksteen

"In the platinum group metals (PGM) industry, smelters are often perceived as ‘black boxes’ that have to process concentrates of variable mineralogy and originating from multiple mines operating along strike or downdip from each other in the same geographical region, as is the case in the Western Bushveld of South Africa. However, PGM smelter complexes are much more sensitive to concentrate blend variation than most metallurgists or geologists would anticipate.This paper will review the impact of concentrate blends deriving from a number of concentrators processing ores from the Bushveld Igneous Complex (BIC) on smelting and converting behaviour and the constraints they impose upon smelter operation. Significant variation in behaviour is not only noted between the main mineralisation types, namely the Merensky and Upper Group 2 (UG2) reefs, but also within a given reef type. Due to the way PGMs are mineralised and finely disseminated, concentrators have to grind concentrates ultra-fine to liberate the PGMs and provide a sufficiently high-grade concentrate for smelting.The chemistry and mineralogy of the concentrates vary with the type of mine (open pit versus underground), the reef type and varies along strike; this variation impacts numerous key smelter parameters such as the base metals content, the matte fall, the converter aisle capacity, sulfur dioxide gas production, furnace matte and slag temperatures, and the accumulation of high smelting chromite-spinel minerals that has led to significant smelter upset conditions such as catastrophic furnace hearth and sidewall failures.Due to the production intensity of smelting, ie its high rate of processing per unit volume, smelters have been found to be far more sensitive to rapid variation in concentrate properties, highlighting the need for adequate blend control.CITATION:Eksteen, J J, 2016. Impact of Mineralogical Variation on the Smelting of Cu-Ni-PGM Concentrates, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By B Crowdey, J Wall

The particular underground operation relating to this paper is a gold producer and has an orebody predominately consisting of rhyolite and marcasites pyrite. The ore has been identified as being reactive to nitrates.Operations currently utilise two twin boom Tamrock™ Super-Drill Jumbos for development mining. Capital (waste) headings have a nominal size of 7 m wide × 6 m high, while ore headings are designed at 5 m wide × 5 m high, with the lower reaches of the mine narrowing down to a 4.5 m × 5 m design. Production drilling is currently undertaken with an Atlas-Copco L6 Solo. Due to the reactivity of the ore, inhibited emulsion phase bulk explosives are used for all blasting activities, with electronic detonators utilised in the production sequence.Sublevel shrinkage stoping is utilised when the orebody is stronger than the host rock. After blasting the ore, and during extraction, the surrounding host rock cannot maintain integrity and it ‘collapses’ on top of the ore. Gravity forces this collapsing rock to follow the blasted ore through the drawpoints.The highest risk involved with sublevel shrinkage stoping is the necessity for charge crews to work upon ‘rills’ at the drawpoints, which are occasionally unstable, to charge the next blast ring to be fired. To overcome this issue a loading technique called ‘precharging’ is used whereby two to three rings are charged, but only the first ring is fired. This technique can minimise risks by taking the charge crew away from the rill and brow.As this mine contains hot and reactive ground, strict guidelines from the Australian Explosives Industry and Safety Group Inc (AEISG) are adhered to. These guidelines relate to the sleep time for the precharged rings.This paper describes the issues faced with precharging in hot and reactive ground, the monitoring required and the systems and procedures that were put in place to enable a successful outcome.CITATION:Crowdey, B and Wall, J, 2014. Precharging sublevel shrinkage production rings in hot and reactive ground with electronic blasting systems, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By S Nkwanyana, I Govender

Batch experiments in a 0.6 m diameter mill have shown that improvements of about 13 per cent in the efficiency of energy utilisation can be realised in ball mills by replacing 25 per cent of the ball charge by an equivalent volume of cost-free critical size pebbles from AG/SAG mills. For a mill of a given size, speed and charge filling, the rate of size reduction of ore particles depends on (i) the frequency of grinding media collisions (ii) the probability of capture of ore particles between the colliding grinding media (iii) the probability of fracture of the captured particles. The probability of fracture depends on the magnitude of collision energy. The distribution of collision energy into shear and impact events determines the relative strengths of attrition breakage and impact breakage. The efficiency of energy utilisation depends on which of the two mechanisms of breakage is more desirable in a particular milling stage. In this paper collision data from a series of DEM simulations of a mill charged with steel media and a mixture of steel media and pebbles is presented in energy spectra and spatial distribution maps. The data provides the necessary detail to elucidate the improvements in the efficiency of energy utilisation in ball mills when using a mixture of pebbles and steel media.

Aug 24, 2022

Optimisation of the Performance of Flotation Circuits Using a Genetic Algorithm Oriented by Process-Based Rules

Sep 13, 2010

By C R. Fountain, R J. Sinclair

The zinc industry is dominated by the electrolytic zinc (EZ) process. The EZ process has a low tolerance for impurities, resulting in tight concentrate specifications. Many mining companies sacrifice zinc recovery in order to meet smelter specifications. Some have ore-bodies that cannot be economically developed because too much metal has to be sacrificed, or it is just not possible to meet the specification. The BUKA Zinc Process (BZP) has been developed as a method of producing high-quality zinc from a wide range of concentrates. It can have lower capital and operating costs than the conventional zinc and lead production routes. Advantages accrue from increases in metal recovery during concentrating, smelting and refining; the elimination of most of the capital and operating costs associated with lead smelting; reduced transport costs; lower zinc refining costs; reduced refinery residue disposal costs; and reduced future environmental liabilities. This paper describes results of testwork that has been undertaken to demonstrate the viability of the BZP on both test rig and laboratory-bench scale.

Jan 1, 1998

By J Lyons, M Hasan, D Pepper, C Vadeikis

Processing of large volumes of ultrafine ores has long challenged mineral processing operators because of lower recoveries and increased tailings. This has led to many deposits, or parts of existing deposits, being viewed as uneconomic. As the mining industry can no longer afford to overlook resources that require finer sizes to achieve liberation or result in high tailings losses, the need for technologies to address these issues has increased. Mineral Technologies (MT) worked with a prominent Australian iron ore producer over five years to implement an innovative gravity separation technology for the beneficiation of ultrafine magnetite. The magnetite mineralisation requires a liberation size of <40 μm and selective rejection of ultrafine silica prior to magnetic separation. Through collaboration with the client, MT applied their Lyons Feed Control Unit (LFCU) technology for the beneficiation of finely grained magnetite. LFCUs are widely used in the mineral sands and iron ore gravity plants, and in tailings applications, to recover water and provide constant high density process streams. This project was an extension of knowledge gained from these applications. Test work was conducted on-site, using 1 t/h pilot and 300 kg/hr laboratory scale units. This test work showed that the LFCUs could reject 20 per cent of feed mass to tails whilst recovering >94 per cent of Fe to product. This upgraded the feed from 53.7 per cent Fe and 19.7 per cent SiO2 to 63.8 per cent Fe and 8.8 per cent SiO2. Recovery by size data showed a minimum 88 per cent Fe recovery to product for <8 μm material and up to 98 per cent Fe recovery for the -38+25 μm fraction. The LFCU rejected 70 per cent of <25 μm SiO2. The information obtained from the test work was utilised in the design of the full-scale units which are due for installation at the project site in 2021. This paper outlines the results of this laboratory and pilot scale test work and how the data obtained was used to design the full-sized units.

Nov 8, 2021

By L Bergin, D J. Williams, S Islam, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. Once mud has formed, typical handling techniques include its costly removal by mechanical means, or its isolation and capping.There are little data available on the moisture state and shear strength of the capped mud. To investigate the effectiveness of isolation and capping, research has been conducted using a large slurry consolidometer (150 mm in diameter by up to 410 mm in height) to simulate capping in situ. Once consolidated, the mud was subjected to shear strength testing in a direct shear box measuring 60 mm by 60 mm by about 20 mm high. The shear strength of the consolidated mud was compared to that of competent, fresh spoil, a mixture of spoil and mud, and to completely degraded spoil (mud alone).These results have been used as inputs in stability calculations using the commercial computer program Slide 7.0, which demonstrates the strong influence of consolidation of the mud on overall low wall slope stability. The results provide insight into the design and construction of capping to isolate in-pit mud.CITATION:Vangsness, T A, Williams, D J, Islam, S, Smith, A and Bergin, L, 2018. Consolidation and shear strength testing and stability analysis of coal mine spoil degraded to mud, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 97–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Principles of management in ore preparation before process of enrichment of chrysotile ores are discussed. The formulas, which were tested in industrial conditions, are offered, which may be used for averaging of chrysotile-asbestos fibres by content in ore and grade.

Dec 6, 2010

By D Giddings, S A. Silvester, S Pickerin

Underground fires represent a constant threat to the safety of underground personnel. Miners in the immediate vicinity may face intense heat, blinding smoke, toxic fumes, fall of ground and other direct effects of a fire. However, the vast majority of victims never actually see the fire, and are overcome either by deadly fumes in the ventilating current or by asphyxiation. The mine ventilation system, which maintains a sustainable atmosphere to the working places, can transport products of combustion with equal efficiency. Miners who are remotely situated from a fire may be forced to evacuate considerable distances, through dense smoke and fumes, or even become cut-off from escape. Additionally, miners may become confused by unfamiliar ventilation characteristics caused by fires. Conveyor belts are widely used for transporting minerals in mines as well as in many other industrial situations. Because they contain large amounts of polymeric materials their use in certain environments, especially coal mines, but also in steel works, power stations and other enclosed areas must be controlled to minimise the fire risk. Over last nine years there have been 60 fires in underground mines in the UK alone and that of these, half have been associated with conveyors. This paper summarises the results obtained from a recent research project that has developed a preliminary computational thermal and fluid dynamic model to represent the spread of flame along a typical conveyor belt used in UK deep coal mines. The results of these models have been calibrated against a series of experimental tests performed within a surface fire test gallery. An improved knowledge of the burn characteristics and rate of release of the products of combustion from conveyor belt fires will assist in the development of better fire detection and fire fighting techniques.

Jan 1, 2005

By P J. Handley

"Predicting how coal seams will be beneficiated through the coal handling processing plant (CHPP) has long been challenging within BHP Coal. Various coal seams from different areas are mined and stockpiled separately, often depending upon a deleterious coal quality parameter; high/low trace elements for example. These stockpiles are then fed in different ratios into the CHPP to produce the desired product/s. In understanding the washability characteristics of the feed source, mine geologists and process engineers work together to improve the beneficiation of different coal materials through the CHPP.For the majority of the BHP Coal deposits, the washability data is available for the coal seams across the deposits. However, no previous standardised modelling and prediction technique existed that could ensure the correct information was available for forecasting and refining CHPP processes. This paper will discuss the steps undertaken to implement a geometallurgical prediction tool that simplified and streamlined the washability modelling and yield estimation process. The value realised to the BHP Coal assets resulting from this process was: improved compliance to plan increased throughput increased CHPP recovery through improved efficiencies and increased revenues.CITATION:Handley, P J, 2017. Washability modelling and estimation techniques used to improve coal handling preparation plant beneficiation, in Proceedings Tenth International Mining Geology Conference 2017, pp 327–336 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

By T Ladinig

Raise caving is a novel cave mining method, which has been proposed for mass mining at increasing mining depths in LKAB operations. The method makes use of the raise mining technology and an active stress management approach. For the implementation the method is split into two phases, namely a de-stressing phase and a production phase. In the de-stressing phase, a slot-pillar system is established. The purpose of slots is to provide stress shadows and the purpose of the large pillars is to control stress and seismicity. The production phase follows after the de-stressing phase. Required infrastructure in the production phase is developed delayed in stress shadows and bulk extraction takes place in de-stressed zones. Eventually the pillars crush and they are extracted in the production phase. A comprehensive research and development program has been launched to develop the raise caving method towards implementation. As part of this program a full-scale test site of raise caving will be conducted as well as raise caving operations are planned for depth extensions in LKAB mines. This paper discusses the design of raise caving operations in practice at the LKAB mines. In particular, the purpose of the paper is to focus on requirements for the development and design of a raise caving operation. The development of raise caving is discussed from a systems engineering perspective as well as from a management perspective. The functional requirements in the destressing and production phase are outlined and discussed in the paper. The discussion is on basis of the main elements of the raise caving system, such as slots, stopes, pillars and infrastructure. Critical rock engineering design requirements in the de-stressing and production phase are highlighted and dependencies between individual main elements are identified. The analyses show that pillars are especially important for the success of the mining method. Overall, the analyses show that raise caving is a complex system and that its development demands a multidisciplinary approach.

Mar 29, 2023

By S Cyphers, J Missen, B Jansen

The AGL Loy Yang Mine is one of the largest and most significant coalmines in Australia. Commencing in 1982, this mine produces 30–35 Mt/a to supply more than 50 per cent of Victoria’s electrical power requirements. At this mine there are unique geotechnical challenges to overcome to ensure its safe operation including: significant mine depth, low density of coal in the operating and permanent mine batters, the influence of groundwater and deep sediment aquifer pressures. One of the challenges is the behaviour of brown coal, which is neither a soil nor a rock and displays long-term creep stress relief. Other geotechnical challenges include ensuring stability in high unconsolidated dumps, potential large-scale block movement in mine batters driven by crack water pressure and heave from high-pressure aquifers.The paper will outline the geological and hydrogeological setting and potential failure mechanisms, and detail an integrated geographic information system and reporting regime that in part addresses ground control management at the mine. The paper will also outline the management processes for a dynamic geotechnical environment and the benefits of the alliance arrangements to meet the geotechnical requirements at the mine and the effective personnel integration in the mine technical services team.CITATION:Jansen, B, Missen, J and Cyphers, S, 2014. Geotechnical management at the AGL Loy Yang Mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By B Hiebl, J Martens, L Petzold

A research team at the Iron and Steelmaking department at Primetals Technologies has established new upgrading measures for improving the efficiency of the beneficiation process in ironmaking plants, relying largely on pre-existing equipment. After the upgrade, the iron content in the final iron ore concentrate was shown to be significantly higher. Remarkably, the costs for employing the respective measures are surprisingly low.This case study is based on a Kazakh iron and steel producer, whose beneficiation process is currently generating a magnetite concentrate with a final iron content of 65.65 per cent. The study shows that the implementation of Primetals Technologies’ intelligent modification measures to the current beneficiation process, the realisation of more effective dewatering, and the utilisation of an innovative binder lead to an increased iron content in the resulting pellets, reaching a concentration of 69.17 per cent (iron ore concentrate) and 66.5 per cent (pellets).The current operation consists of three closed circuit grinding stages, four stages of low intensity magnetic separation, vacuum disc filters and straight-grate pelletising. By dividing the slurry after the second stage of grinding and the third stage of low intensity magnetic separation, it is possible to divert the more iron-rich fines before they would enter the third grinding stage and the fourth stage of magnetic separation. This then reduces the load on the existing third stage ball mill. Afterwards, the ground material is treated in an additional low intensity magnetic separator and mixed with the previously diverted fraction of the fines. An improved filtration procedure, combined with the application of a highly sophisticated binder, further reduces the amount of additives needed, so that a genuine direct reduced (DR)-grade iron concentrate is produced as a result.All laboratory, pilot and pelletising test work was executed at Primetals Technologies’ laboratories in Austria.CITATION:Martens, J, Petzold, L and Hiebl, B, 2017. Enabling iron ore concentrate for the production of direct reduced iron with pre-existing beneficiation lines, in Proceedings Iron Ore 2017, pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

WMC Limited, owner/operator of Olympic Dam, the worldÆs largest underground uranium mine and the fourth largest underground copper mine has now completed an expansion that has been classed as a benchmark in the mining industry. To achieve a production increase from 3.4 to 9.25 Mtpa from an underground mining operation in two years was a major challenge, it was essential to review the overall materials handling system from æthe face to the stockpileÆ. The challenge was two-fold:How to deliver 30 000 tonne of ore per day to the processing plant, from a single underground mine? To provide the processing plant with a consistent metallurgical feed. This paper traces the transformation from the old to the new materials handling system at Olympic Dam.

Jan 1, 2000

By J Schrank

Double-stack trains in the United States date back to the early 1980s, starting about the time deregulation of the rail industry occurred. Freight rail became increasingly more competitive to trucking and barge or ship, and led to major investments in railroad infrastructure. Since most railroad tunnels in the United States were constructed between 1880 and 1930, they were not built tall enough to accommodate modern double-stack intermodal railcars. Therefore, as double-stack trains became the norm, existing tunnels became bottlenecks, and railroads wanted the tunnels made larger without impacting traffic. This need to increase the clearance while not impacting rail traffic launched a very specialised industry: the design and construction of replacement lining systems in existing tunnels.Several large multitunnel railroad clearance improvement projects have been completed in the country in the last decade, and they have all been done under ‘live track’ conditions. Live track conditions consist of work windows, often anywhere from four to 12 hours, that are provided to the contractor to complete the construction work. By the end of each work window, the tunnel must be secured so that the railroad can run trains.In addition to improving the clearance, these projects provided the railroads with an opportunity to improve the general condition of the tunnels, including structural, seepage, drainage and icing conditions. This paper discusses the design considerations, tunnel assessments and construction methods used for these live track railroad tunnel projects. Seepage and drainage improvements that were incorporated into the clearance improvement projects are also discussed.CITATION:Schrank, J, 2014. Live track railroad tunnel repair and clearance improvement in the United States, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 619–628 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G W. Heyes, P J. Guy

Investigations were undertaken to assess the suitability of CSIROflotation methods for improving the efficiency of separation of heavyminerals in the monazite circuit at the Westralian Sands Limitedoperations at Capel, Western Australia. Flotation work was conducted on two plant samples. The first was a high-titanium product containing considerable amounts of zircon and silica as quartz and aluminosilicates, and the second was a low monazite/zircon material containing high levels of silica. A three-stage process including reverse flotation was developed totreat the first sample. In this process monazite, zircon, quartz, andaluminosilicates were selectively concentrated by flotation and screening to produce a titanium-rich product. In the first stage, an acid amine float, monazite, zircon, and some non-zircon silica were recovered and in the second stage, an alkaline amine float using a fluoride activator, more quartz and staurolite were floated. The titanium minerals were thus concentrated in the unfloated fraction. In the third stage, the titanium-rich flotation tail was screened at 250 ¦m to remove the remaining coarse aluminosilicates. In a single pass, the three-stage process yielded a TiO2 recovery of 64.0 per cent with the titanium-rich product assaying 70.3 per cent TiO2.

Jan 1, 2001