Search Documents

By J-P Franzidis, E V. Manlap

Froth transportation characteristics have a significant impact on the flotation recovery especially in large flotation cells. The probability of an attached particle being recovered into the concentrate depends strongly on the location where it enters the froth phase. A mathematical model for froth transportation in industrial flotation cells was proposed (Zheng et al, 2004). The model has been tested on the experimental data obtained from testwork conducted at the Western Metals Hellyer lead/zinc concentrator. The results show that the model fits the experimental data well, especially when the froth is well developed (ie for a deep froth). The model fitting can be significantly improved by incorporating an air dispersion factor. However, the models encounter some limitation, ie inconsistent prediction at different froth heights, due to change in froth viscosity which cannot be modelled at the present time.

Jan 1, 2005

By S Döpp

Commencing with early experiences in iron ore beneficiation made at Beeshoek Mine, the paper follows through the process of extensive mineralogical and metallurgical investigations carried out during feasibility study. The paper will discuss the design process and logic followed over the last years, the challenges and decisions the design team faced in order to draw the conclusions that ultimately resulted in today’s value add approach at Assmang’s Khumani Operations.As integral part of the benefi ciation concept, a focus is set on the jigs, explaining the plant concepts, planned expansions and their contribution to the overall value add approach at the mine.The case study is intended to describe the outcomes of the design versus the actual achieved and the further value add projects to be implemented. As for future prospect, the incorporation of Wet High Intensity Magnetic Separation (WHIMS) demonstrates Assmang Khumani’s pursuit to maximise productivity and overall recovery.DMS was evaluated as an alternative to jigging within a comparative test work study, but in conclusion the option had to be excluded due to its inability to achieve the high density cut point required to achieve the sales specifi cations. In contrast, the investigation on producing an additional middlings fraction on the lumpy ore jigs prove to be an adequate option for further improvements of overall mass yield. With further liberation, a saleable product will be achieved by secondary beneficiation on Fines Jigs and WHIMS.Concluding, jigs are considered the most viable and cost effective benefi ciation process for off-grade ore +0.8 - 32 mm at Beeshoek as well as at Khumani, while WHIMS is the process under consideration for super fines recovery.

Jul 11, 2011

By T Baumgartl, D Mulligan, R Haymont

Mining at the Mt Leyshon Gold Mine in semi-arid north Queensland stopped in 2002. Newmont Australia has recently initiated a thorough post-closure water management study of the site by revisiting the existing information and conducting new water-related investigations. The focus of this paper, which is the first publication on post-closure environmental management of the site, is an overview of the site water quality in view of the sources and spatial distribution of polluted mine water, and also the performance of cover systems in controlling water flux though mine wastes. Since the mine closed the rehabilitation of waste rock dumps and tailings dams have significantly improved water quality in the surface receiving waters. However, the Scats Stockpile, the Heap Leach and Old Plant areas, which can potentially produce acidic waters, enriched with heavy metals and arsenic, are the top management priority. Modelling of the potential transport of contaminants in groundwater needs further investigations. A detailed examination of the waters in seepage sumps showed high concentrations of manganese, cobalt, nickel and selenium, which were previously overlooked. The study also showed distinctive chemical signatures for waters at different locations: the waters draining from scats, supergene materials and waste rocks have distinctly lower pH and higher concentrations of dissolved iron, sulfate, heavy metals, Mg, Mn, U, Se and As. While, the tailings sumps are more alkaline, and are enriched in Na and Cl. The southern tailing sump is characteristically As rich. The waters draining from the supergene materials have higher Cu concentrations. Assessment of the cover monitoring systems showed that although covers pass the design criteria, automated recording of data may ignore any failure of the monitoring system. Recalibration of the moisture sensors not only showed realistic moisture values compared to rainfall data but also showed that the permanently installed system records values that are higher than those of the mobile system. Event-driven recording of data overlooks infiltration events. Besides, with a higher time resolution (daily measurements) the breakthroughs could be clearly detected. Modelling of the water balance in covers is underway and an example is given here. Newmont is currently reviewing water management options and is willing to share the lessons learned.

Jan 1, 2006

By J Cornejo, A Pinochet, C Caviedes

The ore extraction rate and the incorporation of new areas are key operational parameters. In massive deposits mined by caving techniques they both control the cave back geometry, which is mostly responsible for the induced stress state around productive levels. Early detection of deviations from admissible geometries will prevent stability problems related to geomechanical hazards, helping to improve safety and working conditions and reduce the potential for lost reserves.This paper describes a mine planning tool currently in use at the El Teniente mine. This tool involves the control of the cave geometry based on rules that have been defined as a result of different studies and experience collected during the operational history of the mine.This mine planning strategy achieves an extractive mining process with lower risk than conventional planning methods, ensuring ore reserves extraction if followed as planned while reducing unexpected changes in mining sequences.CITATION:Cornejo, J, Pinochet, A and Caviedes, C, 2016. Geometric control for strategic mine planning at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By T Christie

Tertiary volcanic rocks make up a significant proportion of the surficial cover rocks of New Zealand, especially in the Taupo Volcanic Zone. Industrial minerals that are associated with or derived from the volcanic rocks include: amorphous silica, allophane, bentonite, diatomite, ignimbrite building stone, illite clays, halloysite clay, obsidian, perlite, pumice, sulphur, titanomagnetite ironsand and zeolite. Of these: bentonite, ignimbrite building stone, perlite, pumice and titanomagnetite ironsand have been mined and processed for 20 to 30 years, but many of the others require further characterisation of the resource and/or development of markets.   We have compiled interim mineral deposit models for halloysite clays in rhyolite and for zeolites in altered vitric tuffs. These models include geological and mineralogical attributes, which are linked to the underlying volcanic and geothermal processes that have produced the minerals and their source volcanic rocks. Halloysite clay deposits at Matauri Bay (Northland) have formed from hydrothermal alteration and weathering of rhyolite. Clinoptilolite + mordenite zeolite deposits in the Ngakuru area (Rotorua district) have formed from hydrothermal alteration of volcanic glass in lacustrine sediments and ignimbrite. Further refinement and application of these models will result in a better understanding of the mineralogy, localisation and origin of the deposits, with consequent applications in exploration and resource assessments.

Jan 1, 2001

By D Kilkenny

This paper discusses the use of a mechanised shaft sinking machine Herrenknecht Vertical Shaft Sinking Machine (VSM) – to conduct the 93 m presink for the Wira Hoisting Shaft at the Prominent Hill Mine in South Australia. This technology has been widely used in the global construction industry, however, this was the first time it had been used in Australia and the second time in a mining application. The non-entry shaft sinking system eliminates risks associated with a traditional manual method and allows all shaft construction operation to take place from surface. The geology in the upper 100 m at the Prominent Hill mine is conducive to mechanical excavation, with expected rock strengths below 130 MPa. This enabled an alternative shaft construction methodology to be considered. The Herrenknecht VSM system was selected due to its extensive work history and demonstrated performance in similar ground conditions. In collaboration with the operations and design team, the shaft collar and surface configuration were modified to suit the requirements of the VSM, additional equipment, and loading jacks that support the pre-cast lining. Dedicated concrete moulds were designed in Germany and built in Italy. The concrete segments were cast in Adelaide and road freighted to site. This paper outlines each stage of the presink – refurbishment, transportation, logistics, establishment, operation and demobilisation. Selecting this shaft presink excavation methodology, delivered through positive collaboration and communication despite some challenges, shows the benefit to the mining industry of applying new technology and innovation to improve safety and productivity.

Mar 29, 2023

By J Tiihonen, J OÆCallaghan, T Haakana

Outotec is today capable of providing technologies, process equipment and engineering for the construction of pressure oxidation leaching (POX) plants in any location in the world. Outotec works with customers from mine to pure metal, participating in plant design from the process development phase (including test work execution/supervision) to plant commissioning and operations. Either key equipment technology packages with basic engineering or entire POX plants can be supplied.The addition of pressure oxidation equipment to OutotecÆs product portfolio adds to and complements already existing significant experience in general hydrometallurgical process and proprietary equipment design and supply.In addition to providing key pressure vessels, piping and valves to a POX plant, Outotec can offer an enhanced and proven autoclave agitation system that maximises oxygen mass transfer and utilisation. Novel energy and water recovery technology can also be tailored to a customerÆs specific needs. Importantly Outotec owns and operates extensive test work facilities and can provide test work to ensure the optimum POX flow sheet and materials of construction. Outotec ensures that best available technology (BAT) concepts are used in POX design to improve the availability of the process and minimise unpredicted shutdowns.CITATION:Tiihonen, J, Haakana, T and OÆCallaghan, J, 2013. Outotec pressure oxidation - more out of sulfide ore, in Proceedings World Gold 2013 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By M G. Hawtin

The Rocklands copper project is a multilode, iron oxide copper gold (IOCG) + cobalt mineralised system located in the Eastern Fold Belt of the Mt Isa Inlier. Rocklands orebodies cover a range of oxidation zones from oxide, to supergene and primary. Each zone contains different economic minerals of interest. The supergene zones contain significant amounts of native copper and the primary zones are dominated by chalcopyrite. The juxtaposition of these oxidation zones and minerals make it an interesting mineralisation system.Current mine production sampling collects a nominal 3 kg drill chip sample from a 1 m composite, RC drilled interval. A site specific sampling procedure was needed to quantify introduced sampling error when taking grade control samples. Due to oxidation and mineralogical variation in ore zones we needed to develop a practically achievable sampling methodology that ensures minimum sample mass and sample error requirements are achieved to ensure ‘representative’ samples for all ore types.These issues are planned to be resolved using an experimentally derived method using principles from the Theory of Sampling. This method uses an experimental calibration of parameters K and a for Gy’s fundamental sampling error formula using a modified 32-piece sampling tree experiment to compile sampling nomograms for the primary and supergene ores. This paper demonstrates the process undertaken to improve the quality and standard of existing mine production sampling procedures at the Rocklands operation.Results indicate a sample mass of 5 kg for RC drill chips is appropriate for both the primary and supergene ores to achieve a fundamental error below 0.01 or 10 per cent relative error, which is slightly higher than the existing sampling protocol of 3 kg. An additional experiment is recommended to compile sampling nomograms using the exact laboratory comminution and mass reduction stage information to assess the use of a 3 kg sample. The results also indicate no changes are required to existing sampling protocols when sampling RC drill chips in primary and supergene ore at Rocklands.Sampling nomogram results also provide a useful ‘rule of thumb’ reference guide to other mining and exploration companies to help understand minimum sample mass requirements and sampling error during exploration drilling, resource evaluation and mining production stages when targeting similar IOCG mineralised systems. A sample mass of 5 kg is recommended when RC drilling similarly IOCG mineralised prospects and deposits in the Cloncurry area. Future test work is recommended when additional open cuts become active as well as including resource drilling drill core to provide better three-dimensional sample representivity.CITATION:Hawtin, M G, 2017. Minimum sample mass from reverse circulation grade control drilling at Rocklands copper project, in Proceedings Tenth International Mining Geology Conference 2017, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R A. Lynch

The state-of-the-art in cave seismic monitoring is reviewed, with the latest developments in active seismic monitoring included. Seismic monitoring systems are routinely used by most of the world’s block and panel caving mines to track the cave initiation and progression. The current best practice is to use the cloud of seismic event locations as a proxy for cave growth somewhere below. Problems with event location reliability due to seismic ray bending around the (unknown) cave are side-stepped by using sensors installed above the cave. However, the aseismic gap – the (unknown) distance between actual cave back and seismic event cloud – currently hinders reliable estimation of cave geometry.Velocity inversions using the passive seismic data are inexpensive and should be undertaken more routinely. The straight-ray methods should be used with caution, as the underlying assumptions are invalid in caving environments. The double-difference method is more correct for the caving situation, and there have been some promising results published. Constrained geometric inversions make a lot of sense, but have yet to be demonstrated successfully.Two active seismic source have recently been developed for use in the caving environment: a piezoelectric source for ranges up to a few hundred metres and a pneumatically-powered source for ranges up to a kilometre. These sources produce signals on standard mine seismic sensors that can be used to measure seismic velocity variations down to 0.01 per cent resolution. This allows the cave progression to be monitored by measuring tiny changes to seismic velocities as the rock above the cave is fractured and destressed.CITATION:Lynch, R A, 2016. Active and passive seismic monitoring of cave front evolution, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D Will

RedrossThe Redross orebody averages 1 m wide, has a strike of 50 - 350 m, dips at 55° and has a basalt footwall and an ultramafic hanging wall. The most successful and innovative aspects of mining Redross were:•ore development innovations, 90 per cent of development was split fired with a shanty back profile to enable larger and more productive equipment to be used and resulted in higher development grades, improved project payback time and improved ore recovery;•hand held stoping using a multiple level, bottom up ‘V’ shaped hand held stoping method that allowed mining on multiple levels with hand held productivities between 50 and 90 tonnes per shift;•the use of 1 m cement pillars and 7 m high crown pillars were used to create multiple mining areas that enabled high overall production rates from hand held mining this orebody; and•the use of vertical cement pillars to enable hand held mining of adjacent stopes without leaving ore pillars.MarinersThe Mariners orebody averages 3 m wide, has a strike length of 50 - 250 m and dips at 50° with a basalt footwall and poor ultramafic hanging wall. The most successful innovative ideas of re-opening Mariners were:•Dewatering the existing mine workings utilising ‘oilfield’ technology by installing a long submersible pump in on existing pump rising main. This enabled the mine to be dewatered at rates up to 100l/ sec and helped overcome the 45 to 55 L/s inflows.•Overcoming the technical problems associated with Mining N07 ore blocks which had severely deteriorated from being underwater for five years by using reverse firing techniques to improve extraction rates and reduce dilution.•Mass firing a large mining block in the N08 with minimal void space because of deteriorating ground conditions.•Use of a longhole version of the Redross hand held mining method to achieve 100 per cent extraction of the N09 higher grade lenses.

Mar 21, 2011

The Estonia Mine, operated by Eesti Energia Kaevandused AS (EEK), the mining division of the Estonian Government's energy company, Eesti Energia AS, is a large room and pillar mine located in Eastern Estonia. It supplied approximately 4.9 Mt/a of oil shale in financial year ending 2010, which is used for electricity and shale oil generation. Due to the Estonian climate and the power station's need for a dry product, Estonia Mine has developed a planning system where short-term demands of the power stations dictate the schedule. Such an arrangement requires maximising flexibility and consequently the mine only operated for 199 days in 2010.The footprint plays a key role in achieving mass mining rates as the 12 km + 12 km lease area allows the mine to split into mining districts that act independently of each other and maximise the number of work areas available. Coupled with this, the geology of the mine is relatively homogenous over the mining lease, simplifying the mine design and production methods.During the last five years, EEK has commissioned a comprehensive conveyor network. Consequently, material handling only requires loaders to dump oil shale direct from the production face onto a chain conveyor that feeds the conveyor network that ultimately supplies the enrichment plant. Dewatering is also of critical importance, with 90 Mm3 of water discharged annually. EEK uses large trenches up to 3.5 m deep and 1.2 m wide to channel groundwater. Track mounted mechanical saws are used to cut slots in the floor, to control overbreak in blasting these trenches.EEK has introduced Salzgitter Machinenbau GB 280S auger drills that drill three 280 mm diameter holes simultaneously. This has improved void hole drilling times and reduced the drilling required for each face, reducing the overall production cycle time. Blasting activities have also been decoupled from other mining activities negating the need for firing times through the use of small independent firings, required to control vibrations.

Dec 6, 2010

By A Rojc, J Ronaszeki, C Smith

Nuclear logging was tested for the in situ determination of Fe, Si, and Al in iron ore blastholes with field tests at the BHP Billiton Iron Ore, Mount Waleback Mine. Prompt gamma neutron activation analysis (PGNAA) was used to determine percentages of Fe and Si while natural gamma logging was employed for the determination of Al. The accuracy given by nuclear logging is comparable to the accuracy provided by the laboratory analysis which was determined by taking the average of four samples collected from the cuttings deposited on the surface around the perimeter of a drill hole. The work also indicated that there is a chance of determining Al by PGNAA.

Jan 1, 2002

In redesigning the cyanide plant at Mount Torrens, in conjunction with Mr. L. W. Grayson, the manager, several minor alterations were introduced in order to have the operations under thorough control, and these having proved serviceable may be of sufficient interest to merit a description here. The lixiviation vats, though only 8 feet in diameter, were retained, but the pipes leading away from the bottom were reduced from two inches to half-an-inch in diameter, and had a fall to the zinc boxes of about 4 feet. As these small pipes were completely filled by the solutions fiowing away from the vats, they exerted a suction equal to their fall and thus hastened the rate of flow, so that tailings containing a larger proportion of slimes could be treated than was possible where the larger pipes were used, as, there not being sufficient fiow of solution to keep the latter filled, no suction could be obtained with them. It was found that with'most of the tailings treated a sufficient flow could be obtained from the half-inch pipes when the taps on, them were only one-third to half open. The lower end of each of these pipes was connected by means on indiarubber tubing with the sille hole of 11 in aspirator bottle, and to the mouth of this bottle a few feet of similar tubing was connected, so that the solutions coming through could be directed into either of the fixed tubes leading respectively to the waste water tank the strong solution zinc boxes or the weak solution zinc boxes.In working the vats, the following method was found to give good results. While filling the vats with tailings the taps were left open, so that the water might drain off into the waste water tank the surface of the tailings was carefully levelled. When the strong solution was run in at the top, the air contained in the interstices of the tailings was forced through the half-inch pipe at the bottom as a strong blast, instead of, as I believe js usual, escaping by means of channels formed by it through the tailings, and thus tending, it would appeal, to render the disposition of the tailings less even and to make.

By R Dwyer, S Rea, W J. Bruckard, N McSweeney, R Holmes

"The innate ability of microorganisms to adapt to changing or inhospitable environments has often been exploited for industrial purposes and forms the basis of many current biotechnological processes. The ability of bacteria to adapt and adhere to specific mineral surfaces ensures that the energetic or nutritional requirements of the cell are met and often serves as a survival mechanism under unfavourable?growth conditions or conditions of stress. In this process, cells may rearrange or modify the macromolecules expressed on the cell surface itself or produce extracellular molecules, modifying mineral surfaces to render them more suitable for growth. The modifications that these molecules produce on mineral surfaces may result in changes to the surface charge and hydrophobicity of a mineral. As a result, these biomolecules may have some potential application as flotation collectors or modifiers.In this work, the effect of long-term exposure of Paenibacillus taiwanensis to goethite and common gangue minerals associated with Australian iron ores on the differential expression of membrane and extracellular proteins was determined. Both groups of proteins play a role in cell adherence to mineral particles. Cells were adapted to grow in the presence of each mineral over time. The proteins expressed on the cell membrane and the extracellular proteins excreted by the cell were isolated and analysed by two-dimensional polyacrylamide gel electrophoresis (2D gel PAGE). The outcomes of these studies are presented here and potential application of these products for flotation discussed.CITATION:Dwyer, R, Rea, S, McSweeney, N, Bruckard, W J and Holmes, R, 2013. Microbes and their metabolites - potential iron ore flotation reagents, in Proceedings Iron Ore 2013, pp 369-372 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By R Hall

Subduction zone magmatism is a direct response to tectonic and chemical processes operating at convergent margins. Changes in the tectonic configuration of plate boundaries in SE Asia during the Cenozoic had consequences for the nature and volume of magma produced. Retreat or advance of the trench hinge has probably been an important process in controlling the presence or absence of magmatism in SE Asian subduction zones. This process also provides a means of replenishing the mantle wedge and counteracting the effects of melt extraction in depleting the wedge. Changes in the nature of recycled material and lithologies of the over-riding plate also have the potential to influence the lavas that are erupted in arcs. Several locations in SE Asia have experienced magmatism bearing the geochemical signature of subduction but are remote from coeval subduction zones. Such magmatism requires an earlier period of mantle enrichment by subduction but may result from localised extension. The distribution of such magmatism may provide information of tectonic value. Some adakitic magmatism occurred in tectonic settings where there is no evidence for subduction of young oceanic crust at the time of magma genesis. Slab melting in such settings is not possible and alternative mechanisms are required to explain the occurrence of, at least some, adakitic lavas.

Jan 1, 1999

Influence of Grinding Media on the Flotation of Carbonate Using Sodium Oleate as Collector

Sep 13, 2010

By K Osten, N Scagliotta, G Lane

Oceana Gold (New Zealand) Limited operates the Macraes Gold Mine near Dunedin on the South Island of New Zealand. The orebody is mineralogically complex and comparatively low grade requiring a series of unit processes and resulting in a relatively complex plant. As part of Oceana GoldÆs ongoing Business Improvement program, a concerted effort has been made to focus on operational efficiency. One aspect of this has been the efficient use of energy in the gold recovery process. A benchmarking process has been developed for the Macraes operation that includes comparison with other operating mines and theoretical design. Criteria for determining operational efficiency have been developed. While benchmarking is, in theory, a simple process, this paper looks at putting benchmarking into practice by catering for variability in ore and associate processing methods. The unit processes discussed include the comminution circuit, flotation plant, pressure oxidation plant and gold recovery circuits.

Jan 1, 2004

A simulation and animation model was constructed for the Stockton Coal Mine. This mine is located in the north western area of the South Island of New Zealand. This model was used to study the optimum size of the stockpile areas whilst achieving the correct product coal qualities. The model evaluated the impact on stockpile size and product coal qualities for both bulk and selective mining. The effect of modifying the amount of known clean coal quality was also investigated. The software used was GPSS/H« for the simulation and Proof Professional« for the animation. From the study, it was recommended to incorporate selective mining in future studies. The shipping plan needed to be modified for a better correlation between coal production levels, in situ coal resources and wash plant capacity.

Dec 6, 2010

By L J. de Lange

As a material asset for mining entities, the resources and reserves (RR) estimation processes are surprisingly underrepresented in the assurance landscape. When press reports expose them being inaccurately reported, or in merger and acquisitions processes, their importance becomes clear. The impact of erroneous RR numbers (both positive and negative) could have a material impact on an entity’s reputation and value.The technical nature and ‘black magic’ connotations of the RR estimation processes are possibly reasons why audit committees are not actively involved with it. Internal auditors avoid the RR processes for similar reasons. Also the traditional approach to obtain assurance on RR is expensive and is therefore only performed when it is absolutely required.However, stakeholders’ expectations of good governance are growing. Part of this increased focus is based on attaining a higher degree of certainty about the current and forecasted position of the entity. Stakeholders are also increasingly more interested in non-financial areas of entities, as the future success of an entity is more than a set of financial metrics.Consequently, the RR estimation processes should be visible on the agendas of audit committees. Monitoring of key controls is required as part of the governance obligations for senior management and the audit committee. So once it is on the audit committee’s agenda, the question then becomes, how will that agenda be supported by an assurance process that is cost-effective?The main objective of the paper is to describe a model of RR assurance that has been effectively applied in some mining companies. The paper discusses one particular approach that provides an audit committee with the required assurance regarding RR processes. The approach ties the assurance needs of the audit committee to the needs of the technical experts in the entity, therefore involving two important figures. It also offers assurance providers with a model to audit ‘through’ the RR processes rather than ‘around’ them. The paper then discusses top-down and bottom-up approaches that provide assurance at different levels of an entity.A governance audit that focuses on the RR processes is suggested as a top-down approach. A bottom-up approach assesses the design adequacy of internal control processes. A hybrid model is described which meets the needs of diverse stakeholders including the audit committee and the RR community.The hybrid model combines the expertise of professionals in both internal audit and RR. The right balance of these skills directed by a singular approach ensures that a credible result is achieved.This approach is not as expensive as some verification approaches used in the industry and can, as a result, be performed on a more regular basis.The last element of the paper looks at implementation of the reporting mechanism. An assurance process aimed at continuous improvement further enhances the robustness and reliability of RR reported by an entity.CITATION:de Lange, L J, 2016. Resources and reserve assurance processes – a framework for improved governance, in Proceedings International Mine Management Conference, pp 21-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses collector residuals, metal concentrations in solution, and other parameters.Collectors used in the plants studied were various xanthates, Z-200, and Aerofloats. Xanthate residuals varied in different ways in most plants. However the general trend was for residuals to be at the O· 5-2 p.p.m. level in lead flotation and O· 5 p.p.m. or less in zinc flotation.Aerofloat residuals were also variable but in the plant concerned were at a much higher level (8-10 p.p.m.) than xanthate residuals. Z-200 residuals were in the 10-20 p.p.m. range and it was found that the Z-200 added to zinc flotation was reporting in dam return water and entering lead flotation.Copper concentrations in solution were negligibly low in those plants where cyanide was not used. When cyanide was used, copper was at the 5-20 p.p.m. level and appeared to be present as Cu(CN)-2. However the hiocyanatepresent may be important. Xanthate was also present in these solutions.Zinc concentrations ranged from 0·1 to 800 p.p.m. in different plants. The general trend was for the zinc level to be highest in the grinding circuit and to drop during flotation. However there was always an increase in zinc concentration when copper sulphate was added, even tho.ugh this incre.ase was not permanent, and the increase was greater with higher copper sulphate additions.The manganese concentration also increased appreciably during copper-activation of marmatite. In some plants lead concentrations increased from 0·1 to 1 p.p.m. during activation of marmatite.Calcium concentrations (20-1200 p.p.m.) and magnesium concentrations (10-600 p.p.m.) tended to be fairly stable in each circuit.

Jan 1, 1970