Search Documents

Flotation Performance Improvement by Air Recovery Optimisation on Roughers and Scavengers

Sep 13, 2010

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011

By Moresby J. F

Segregation roasting was used to recover more than 85 per cent of copper from crushed, minus 14 mesh refractory furnace-lining bricks. A plus 14 mesh fraction: which was high in copper, could be recycled directly to the smelter, giving an overall recovery of approximately 90 per cent. An oxidation roast at about 700°C was necessary, before segregation roasting, to convert copper sulphides and copper metal to sulphates and oxides. Withsegregatron temperatures in the range 600°-650°C the quantities of solid carbon and NaCI required are 2-5 per cent and 1 per cent respectively. P.V.C. coating from scrap copper wire can be used instead of NaCl as asource of hydrogen chloride for the segregation reaction.

Jan 1, 1978

By N McKenzie, E Taylor, S V. L Barrett, H Lagger, A Purwodihardjo

This paper discusses the temporary support design methodology for the largest road caverns ever built in Australia—the Lutwyche Caverns—part of the Airport Link project in Brisbane, Australia. The Lutwyche Caverns with a maximum excavated span of 27 m form a key component of this major road project, allowing on and off ramps merging with the underground highway. In addition to the two large span caverns, a 15 m soft ground tunnel with 5 m cover above the caverns and two 24 m deep burial chambers for the 12.4 m tunnel boring machines (TBMs) had to be built in record time at Lutwyche.The temporary support design methodology involved the use of a range of analytical approaches, including empirical methods to provide a starting point for design development, key block models to determine the potential influence of discontinuities on excavation stability and 2/3D continuum and discontinuum models to determine the potential influence of adjacent excavations and the proposed construction staging on the design. In addition, probabilistic analysis of potential kinematic instability using a discrete fracture network (DFN) approach was also undertaken to establish the critical block loads for the temporary lining, while the continuum and discontinuum models were used to design the support for the 1.5 m diameter rock pillar at the north end of the northbound cavern.The numerical modelling was undertaken in close conjunction with the contractor to develop the optimal construction sequence, considering the available construction equipment on-site and the overall project program requirements. Part of the presentation will further show the applicability of the developed design during construction (deformations, monitoring field observations) and lessons learned for future cavern construction in Australia.CITATION:Lagger, H, Purwodihardjo, A, Barrett, S V L, McKenzie, N and Taylor, E, 2014. Temporary support design for the largest road caverns ever built in Australia – the Lutwyche Caverns, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The paper presents a brief history of endeavours to start a mining education programme which began in the days when Papua New Guinea's first large mine, at Panguna (Bougainville), was coming into production. The status of the Public Investment Programme in Mining Engineering and the facilities being created for the education and training of Papua New Guinean citizens in mining and mineral processing are also described. Future expansion plans are also detailed including those for the commencement of petroleum engineering and geological engineering which would include courses in mining geology, exploration geology, engineering geology and petroleum geology. The paper also looks at the manpower training requirements in the lower levels of mining industry such as pit foreman, blasting foreman and other similar positions. It stresses the need to start mining technical training programs at pre- employment level and at certificate level in a technical college, possibly Lae Technical Colleqe.

Jan 1, 1991

By Lee T. J

The area, A, under a gamma-ray log that passes through a horizontal bed given by: A = gl/k. Here is the equivalent concentration of U3O8 in the body, l the thickness of the body, and k the calibration factor or sensitivityof the logger. The area is independent of the logging speed or logger time constant.This relationship, together with the first moment about the maximum of the log and its value there suflicient to determine the thickness, position of the centre of the bed from the log maximum and the concentration of U3O8.Numerical results obtained from artificial and field data show that the computed results arc as good as those obtained by methods such as the inverse filter technique and the iterative method. The present method yields results that arc easier to feed into an ore reserve data base.

Jan 1, 1981

A review of historic mining information and geological literature pertaining to the Alpine Mine, Lyell Goldfield has been completed. As a result of this work the Alpine reef is inferred to be associated with an upright anticline with a sub-horizontal axis. Structural profiles prepared from limited underground data indicate that the reef is subparallel to the eastern limb of the anticline and cuts across the western limb. Reassessment of structural mapping completed by the New Zealand Geological Survey indicates that Greenland Group metasediments within the Lyell Goldfield are folded into a series of opposed assymetic folds with sub-horizontal axes. It is suggested that the anticline which harbours the Alpine Reef is located on the axis of a synclinorium. Along the western limb of the synclinorium the subsidiary folds have steep west dipping limbs and shallow east dipping limbs (western sense of assymmetry) whereas shallow west dips and steep east dips are typical of the eastern limb. The notion of quartz mineralisation occupying the axis of a synclinorium is contrary to the situation in the Reefton Goldfield where quartz mineralisation is affiliated with folds associated with an anticlinorium. Historic mine data reveals that below No.4 Level the quartz-gold mineralisation, in the Alpine Mine, occupied a steeply dipping ore channel. The strike of the channel was to the northwest and within this structure the are shoots plunged to the north at approximately 40¦. Archival mine plans show that two quartz bodies, the North and South Blocks, were present at No. 4 Level. Although the North Block was followed down to No 14 Level (530 m vertically below the surface outcrop) the South Block was only mined as far as No 7 Level. Sampling on No 7 Level together with the results of trial mining suggest that the grade of quartz underfoot in South Block is low. Information from the Mines Statements and mapping undertaken by the Gold Prospecting Scheme reveals that faulting had a profound influence on the intregity and extent of the Alpine Reef. The reef occupies a Inajor shear zone but little is known about it. It is also apparent that below No 7 Level the reef was progressively shattered by faulting and this may be the chief reason for the decrease in grade in the lower levels of the mine. No substantive facts are available about wall rock alteration effects adjacent to the Alpine Reef Still this is not surprising considering that comments on the mineralised pug envelope and breccias adjacent to the mined quartz shoots at the Globe - Progress Prospect were omitted from contemporary publications. In spite of this the existance of sulphide bearing reef casing lithologies cannot be completely dismissed since 9.15 m of 'reef track' has been reported in Reids No 2 Level.

Jan 1, 1996

By Holmes R. J, Miles J. G

An on-stream shale detector has been developed that is suitable for use on conveyor belts carrying iron ore of up to 200 mm particle size. The shale is distinguished from high-grade iron ore by means of the substantially greater total natural gamma-ray activity (400-3000 keV) of the shale, which is due to the presence of uranium (214Bi), thorium (208TI) and potassium (40K). Other gangue materials, sueh as highly siliceous cherts and jaspilites, escape detection because of their low activity. A dynamic trial of the shale detector at Mt Whaleback, using a large-volume (100 × 100 400 mm long) "Polyscin" Nal(TI) gamma-ray detector, demonstrated that as little as 20 tonne of ore on a conveyor belt (equivalent to partial truckloads of ore) can readily be monitored for shale content.

Jan 1, 1981

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the rate of extraction of gold. This is due probably to the activation of passive gold by the thallous ions. Lead, bismuth, and mercury salts, which should produce a similar effect, fail to do so. It is postulated that this latter result, together with the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide.INTRODUCTIONThe work of Fink and Putnam (1950) showed that the rate of solution of gold in cyanide can be increased by the addition of small amounts of lead, bismuth, mercury, and thallium salts. Mills (1951), during a study of the electrochemistry of gold, with particular reference to cyanidation, was able to show that gold may become passive towards cyanide solution. The addition of lead or thallium salts prevented this passivity, although the action of lead was limited to the pH range 10 to 12. In a recent paper Cathro (1963) confirmed the findings of Mills, and presented results which showed that the addition of thallium to a cyanide leach of a calcine from Lake View and Star mine, Kalgoorlie, increased the rate of extraction of gold appreciably. In, this paper the use of thallium to prevent the gold becoming passive, and hence to decrease leaching time and cyanide consumption, is examined.EXPERIMENTALA series of leaching tests was carried out on a sample of Lake View and Star calcine, comprising calcined pyrite (about 70 per cent.) and siliceous gangue (about 30 per cent.) and containing 165 p.p.m. gold, 45 p.p.m. silver, 0·1...

Jan 1, 1964

By C E. Vidal

Geological exploration and mining development increased their intensity and rate of success during the last five years in Peru. Particularly relevant are the mining projects of Yanacocha and Pierina for epithermal Au and Ag. Also relevant are the new mining operations at Iscaycruz and Uchucchacua for limestone replacement Zn- or Ag-rich base metal skarn deposits. Miocene continental volcanics host the low-grade but near-surface orebodies of the Yanacocha mining district in Cajamarca. Several deposits have been mined since 1994 with open-pit and heap-leach gold production increasing from 300 000 ounces to 1 300 000 ounces in 1998. In a similar geological setting, but with three times the grade of Yanacocha, the Pierina valley-leach operation in Ancash is set to produce 800 000 ounces Au during 1999. At Iscaycruz in Lima, Cretaceous limestones host massive pyrite and sphalerite skarn deposits with 10 to 20 per cent Zn. Mining and milling were started in 1996 with last yearÆs production rising to 180 000 tonnes of Zn concentrates. At Uchucchacua, selective underground mining of fracture-controlled Ag skarns, with 400 to 420 g/t, has been recently increased from 1200 to 2000 tonnes per day to produce 5.5 million ounces Ag during 1998. Advanced exploration projects are located in the framework of nine Phanerozoic metallogenic provinces. Mineral deposits of preferred attention are precious metal disseminations and veins, base metal replacements and skarns, porphyry Cu (Mo-Au), Mississippi-Valley-type Zn and base metal volcanogenic massive sulphide deposits. Geological discovery of new orebodies enables a sustainable development of the mining industry in the country.

Jan 1, 1999

By C A. Locke, M Stevens, P Vidanovich, J Cassidy, J L. Mauk

The Karangahake adularia-sericite epithermal gold-silver deposit, located at the southern end of the Waitekauri Corridor, Hauraki Goldfield, occurs as quartz veins with associated alteration haloes. Integrated geophysical studies were undertaken to determine the expression, location, and extent of these alteration zones. Aeromagnetic data show an extensive, magnetic æquietÆ zone over Karangahake and the southern Rahu Ridge that represents a zone of magnetite destruction resulting from hydrothermal alteration. Analytic signal data are used to define the boundary of this zone; the resulting 6 km2 area is elongate north-south with an irregular boundary. A detailed gravity survey over the area reveals a positive residual gravity anomaly, up to 30 gu in amplitude, over the Karangahake deposit. Density measurements on near-surface rocks give low values indicating that the source of this positive gravity anomaly must be deep; possible causative bodies include an igneous intrusion or dense sulfide mineralisation. To the west and east of the host Waipupu Formation, strong gravity gradients of 100 gu/km and 65 gu/km reflect the faulted boundary of the Hauraki Rift, and the edge of the Waihi Basin respectively. High resolution airborne radiometric data define a 2.2 km2 area of potassium enrichment. This area is elongate north-south and has an irregular boundary. It coincides approximately with the centre of the magnetic quiet zone and the peak of the gravity high, and correlates with known areas of intense mineralisation. Anomalously high potassium counts and elevated K/Th ratios correlate with areas of potassic alteration that have undergone K-metasomatism. Underexplored portions of this zone may indicate areas of gold-silver prospectivity. Combined geophysical data therefore reveal the extent of hydrothermal alteration, and the central zone of Kmetasomatism that is most likely to contain orebodies.

Jan 1, 2005

By S McGregor, J Sharp, I Entezari, T Boulter

The piezocone penetration test (CPTu) is one of the primary screening tools used by the mining industry to evaluate whether tailings are susceptible to liquefaction (static or cyclic). Liquefaction analysis using the CPTu is influenced by the fines content of the soil, and most CPT screening tools empirically use the behaviour type index (Ic) to correct for fines. The issue with this approach is that such empirical relationships have been developed using data collected from natural soils and their applicability to different tailings deposits needs to be studied. In this paper, we explore the use of machine learning to develop a site-specific model to estimate fines content of tailings using gamma piezocone penetration testing (GCPTu) measurements. The results are then compared to the fines content derived from the soil behavior type index (Ic) proposed by Robertson and Wride (1998). A dataset of paired GCPTu and laboratory results were compiled and a support vector machine (SVM) algorithm was employed to calibrate a model to estimate tailings fines content from in-situ GCPTu data. We calibrated GCPTu data to geotechnical 75 μm fines content measured in the laboratory. The geotechnical fines content is the fines content as a percentage of solids. The development dataset was comprised of paired GCPTu-laboratory results collected in 2009-2019 from a mining area with predominately clay mineral and quartz sand tailings. Results show that the developed model predicts the geotechnical 75 μm fines content of the studied deposits with 7.8% error. The Ic based method estimates the fines content with 31% error. Evidently, the Ic method is not applicable to the studied tailings deposits. It is appreciated that many tailings fines do not contain clay, and that the success on this program may not be repeatable everywhere. However, the authors wish to point out that the application of site-specific machine learning algorithms may be used to significantly improve empirical geotechnical parameters.

Jul 1, 2021

By S Natsui, Y Goto, S Kawanishi, J Takahashi, H Nogami

The demand for copper increases yearly, and further improvements in copper smelting efficiency using flash furnaces are required. This study was conducted to understand and promote the interfacial reaction associated with the collision of silica flux and iron oxide particles, ie the formation reaction of fayalite slag, in the reaction shaft of the flash furnace. High-temperature microscopy was used to observe the reaction behaviour of a 2 mm granular SiO2 reagent in contact with micrometreorder- sized FeO reagents in situ. When the amount of FeO was lower than the stoichiometric amount with SiO2, the molten slag formed at the interface between FeO and SiO2 diffused into the SiO2 particle before dissolving the remaining FeO particles. It did not contribute to the subsequent reaction, and despite having the lowest amount of FeO among the samples in this study, many unreacted FeO particles remained on the surface of the samples after testing. On the other hand, under conditions with high FeO content and close to the eutectic composition of the FeO-SiO2 system, a liquid phase formed from low temperatures, gradually increasing in volume and eventually completely dissolving the 2 mm SiO2 grain. These results indicate that the early-stage slag is essential in increasing the interfacial area between FeO and SiO2 and facilitating the supply of FeO to SiO2. In other words, the FeO/SiO2 determines the amount of liquid phase and significantly influences the subsequent interfacial reaction rate between FeO and SiO2. Therefore, the local FeO/SiO2 of the particles falling down the reaction shaft should also be optimised to ensure early slag formation. Meanwhile, the time required for 2 mm SiO2 to complete the reaction for the temperature history employed in this study was significantly longer than the particle residence time in the reaction shaft. Further detailed investigation of the effects of silica flux particle size, composition, and reaction temperature on the reaction time will help find the conditions under which the reaction of silica flux can be completed in the reaction shaft. These kinetic approaches could contribute to future innovations in the copper smelting process using flash furnaces.

Jun 19, 2024

By Segnit E. R

Results are reported of a study of the reactions occurringin the combustion of chaIcopyrite particles underconditions simulating those in the shaft of a flashsmelter.The reactions were studied using kinetic and mineralogicaltechniques. Reactions. rates above 500°C wererapid, most of the reaction taking place in less than 50ms. Final products were copper-iron ferrites with spineltype structures. Probable reaction mechanisms are discussed.

Jan 1, 1977

By S Lush, R Polglase

McConnell Dowell is pleased to be given the opportunity to present two papers to this conference. The first is a general discussion paper on our work in the field of slurry transportation. The second will be a technical paper on the development of a welded coupling compatible with urethane lined pipework. We trust that by discussing our recent work we can leave two lasting impressions on you: the versatility and useful role of slurry transportation, and the leading role taken by New Zealand in this technology This paper discusses three recent projects the New Zealand Steel Ironsand Transfer Line the Coarse Coal Ship Loading Technology the Nerang River Sand By-pass System. These have followed on from the other slurry projects with which McConnell Dowell has been associated such as the ironsand export trade at Waipipi and Taharoa. The New Zealand Contractors Federation awarded the Construction Award for 1986 to McConnell Dowell for the Ironsand Slurry Pipeline.

Jan 1, 1986

High Pressure Sulfuric Acid/Oxygen Leaching of Platinum Group Metals Bearing Ni-Cu Mattes The processing of platinum bearing Ni-Cu ores for the extraction of platinum group metals (PGMs) involves comminution, flotation, smelting, and converter treatment of the furnace matte. Leaching circuits are predominantly used for further processing to separate the base metals and PGMs contained in the converter matte. Nickel dissolution is primarily achieved in the first stage leach (high pressure or atmospheric leaching, or a combination of the two), which is followed by second stage high pressure sulphuric acid/oxygen leaching to dissolve copper and the remaining nickel. PGMs are recovered from the leaching residue in downstream processes, and their dissolution in the first two leaching stages must hence be limited. Studies have been conducted to investigate the leaching mechanisms and kinetics of base metals in different leaching environments. The key operating parameters that influence the leaching kinetics of these metals include the temperature, acid concentration, degree of agitation, feed particle size distribution, and oxygen partial pressure. There is, however, a limited understanding of the behaviour of PGMs in the high pressure leaching process. Consequently, this process is controlled based on operators' intuition despite its importance in the recovery of PGMs. An improved fundamental understanding of the behaviour of PGMs in this leaching environment is required to be able to accurately model the process. This in turn will allow the development of an improved control strategy and the estimation of optimum operating conditions. An overview of the leaching mechanisms of base metals and the effects of key operating parameters on their dissolution kinetics in different leaching environments are presented. Models that have been developed to predict the leaching behaviour of base metals are discussed and evaluated. Finally, initial results obtained with an experimental setup that will be used to investigate the behaviour of PGMs in high pressure leaching systems are discussed and compared with published results.

Sep 13, 2010

Flow Sheet Simulation of Municipal Waste Treatment Processes

Sep 13, 2010

The Junction Reefs gold bearing deposit is situated on the Lyndhurst Mining Field in mid-west New South Wales. It is located within a triangle of three country towns namely, Blayney, Cowra and Canowindra, all three townships are approximately 25 km from the current operational mining leases. The district is well developed, having been settled for more than a cen- tury. However, being close to the Cities of Orange and Bathurst it is real- lised, instantly, that mining leases have been pegged, in this area, almost boundary to boundary. The lease patterns are, with few exceptions, those which had been estab- lished more than seventy-five years ago. These types of lease patterns may not assist the proper exploitation of a large district where there have been many discoveries of gold, copper and other metals.

Jan 1, 1988

By J K. Wright

In recent years the production of steel from directly reduced iron ore pellets has expanded rapidly. However, continued growth will depend on an adequate supply of suitable raw materials for the various commercial gaseous and solid reductant processes now in operation. Although at present Australia does not produce pellets primarily for direct reduction, there is an increasing awareness of Australia's potential role as a supplier of high grade ores for export and/or domestic use. The properties and quality requirements of iron ore pellets made specifically for direct reduction (DR) are reviewed and the laboratory techniques and test methods used at the CSIRO Division of Process Technology for the evaluation of potential DR feedstocks are described. At the present time most of the evaluation tests for DR pellets are extensions of those designed for existing blast furnace (BF) burdens. In the case of some physical parameters such as cold compression strength, abrasion index and cold strength after reduction this extension is quite satisfactory. In the measurement of parameters such as reducibility, swelling and sticking tendency, however, it is necessary to develop meaningful standardized tests so that ores and pellets can be ranked for DR performance. To do this, data from the laboratory tests and from operating plants must be correlated.

Jan 1, 1980

By Sewell L. G, White H. S

OWING to two large falls of ground which resulted in serious accidents occurring towards the end of 1908, it became evident that the "open chamber" system then in use was unsuitable for the conditions existing in the Mount Morgan mine. It will be admitted that in all mining operations the first consideration is the economy of the system adopted, combined with its safety and ability to give the desired output. A sectional system with square sets has been introduced into the mine, in which due attention has been paid to these factors. In this paper a brief description of this system will be given. An outline of those previously used will be included, as it is necessary to understand the conditions which existed in the mine at the initiation of the sectional system. Outside the actual mining methods employed, various points that might prove of interest will be touched on.The square set system of mining has been in use throughout, the stopes in the gold ore in the upper levels of the mine since underground operations were started in Mount Morgan. In the oxidized zone the ore was of a friable nature, and in some cases rImning ground was encountered. In the lower levels the ground became heavier, and although the stopes were for the most part long, wide, high, and irregular, and not sectionalized, no difficulty was experienced in winning the ore, and no accident of a serious...

Jan 1, 1911