Search Documents

By V. Koump, T. F. Perzak, R. G. Olsson

The rate of dissolution of recrystallized alumina in molten iron oxide in equilibrium with iron at 1450°C was studied by rotating alumina disks in the melt. The samples were rotated from 1 to 12 min at speeds from 54 to 3270 rpm. It is concluded from the experimental results that the process is limited by diffusion in the liquid boundary layer. The interdiffusion coefficient for the dissolution of alumina disks in pure molten iron oxide was estimated to be about 3 xl0-5= sq cm per sec. THE erosion of refractory materials is of considerable importance in iron- and steelmaking processes. Since many refractories contain alumina, this investigation was undertaken to develop a further understanding of the erosion mechanism. Shurygin et al.1-3 have investigated the rate of dissolution of alumina in molten silicates and molten fluorides by rotating alumina disks in various melts. The rates were reported to be limited by diffusion in the liquid boundary layer. In the present investigation the rate of dissolution of alumina in molten iron oxide in equilibrium with iron was studied in a similar manner; alumina disks were rotated at different speeds in molten iron oxide at 1450°C. The relationship between the rate of dissolution of the flat surface of the disk and the speed of rotation was used to determine whether the process is limited by diffusion in the liquid boundary layer or by some chemical reaction mechanism. APPARATUS AND EXPERIMENTAL PROCEDURE A schematic diagram of the experimental apparatus is shown in Fig. 1. The iron oxide melts were contained in 2-in.-diam high-purity iron crucibles that were centered in a cylindrical graphite susceptor. Prior to each sequence of experiments, sufficient reagent-grade ferric oxide was added to a crucible to form approximately 350 g of molten iron oxide; the depth of the melt was about 11/2 in. To prevent excessive erosion of the crucible, about 70 pct of the required iron was added to the crucible in the form of iron powder. The mixture was melted in an atmosphere of purified argon by induction heating with a 250-kc generator. After the oxide was molten, a Pt/Pt-10 pct Rh thermocouple at the exterior of the crucible was calibrated against an iron-sheathed thermocouple immersed in the melt and was thereafter used to regulate the melt temperature. All experiments were conducted at 1450°C with a probable error of 10°C. The alumina disks were constructed from pure re-crystallized alumina having a density of 3.7 g per cu cm (porosity approximately 6 pct). For each disk sample a 1-cm-diam alumina cylinder of known length (0.9 to 1.0 cm) was cemented into a ground seat at the end of a 1.27-cm-OD centerless ground alumina tube. The ends of the tube and cylinder were flush and served as the disk surface. When mounted in the apparatus the alumina tube was guided by tungsten carbide bearings and rotated by a variable-speed motor. The bearing and drive assembly could be raised and lowered in order to allow the sample to be quickly moved in and out of the melt. At the start of an experiment, a sample was preheated for several minutes directly above the melt, and then immersed in the middle of the melt to a depth of a in. and rotated for 1 to 12 min at speeds of 64 to 3270 rpm. The speed of rotation was measured by a hand tachometer. At the start and completion of each experiment, a melt sample was withdrawn with a cold copper rod and the alumina content was determined by chemical analysis. During individual experiments the alumina concentration of the melt changed by the order of 0.25 wt pct. Average melt compositions for individual experiments were used in the subsequent computations and were in the range between 0.12 and 4.3 wt pct alumina. The extent of dissolution was determined by sectioning the end of the sample and measuring the final length of the alumina cylinder with a microscope. Since the exposed end of the cylinder, i.e., the disk surface, was etched in a manner characteristic of this geometry, a number of measurements were made on

Jan 1, 1969

By R. G. Ward, John Henderson

It has been shown1 that the observed density1-' of liquid iron silicates in contact with solid iron depends upon whether nitrogen or argon is used to protect the experimental system from oxidation. These densities have been measured by the maximum bubble-pressure method, in five different labora-

Jan 1, 1965

By W. D. Keller

THE high-alumina clays of Missouri are interesting for several reasons. They are the only sedimentary deposits in North America of first grade (over 70 pct A1,0,) diaspore and boehmite sufficiently large to be mined commercially. Mineralogically, they are composed of diaspore and boehmite in intimate coexistence, but gibbsite, the common hydrated alumina mineral in bauxite and laterite, is absent, or is exceedingly scanty if present.* Therefore, the Missouri high-alumina clays do not represent typical laterization. The physical chemistry leading to their mineral genesis, and the geolbgical setting for their formation, present important problems for scientific study. The origin of the Missouri high-alumina clays has been discussed in earlier reports by Allen1 (1935) and McQueen 8, 9 (1929, 1943). These investigations were made under difficult conditions, however, because no diaspore deposit had been opened where a Paleozoic (Pennsylvanian) rock cover lay undisturbed over the high-alumina clay. The relationship of the clay to only the underlying rocks could actually be observed. Lacking the guidance of critical postdepositional geologic evidence, undue and erroneous emphasis was placed on the postdepositional leaching of the deposits in the theories on the origin of diaspore and boehmite from clay (hydrous aluminosilicates) . With new geologic evidence at hand, a clearer picture can be made for the origin of the Missouri high-alumina deposits. In this paper the geology of a diaspore deposit whose original Paleozoic cover had not been eroded will be described and interpreted genetically. The close relationship of boehmite and diaspore (also with kaolinite and a chloritic mineral), will be established. A theory of origin for the high-alumina clays, consistent with the new data, will be postulated.

Jan 1, 1952

By S. P. Kinney, A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

By R. Buehl

ALTHOUGH the main features of the transformations occurring in 18-8 have been published already,1-4 certain conclusions merit questioning and discussion. The questions may be summarized as follows: PERCENT REDUCTION BY COLD ROLLING FIG. 1.-VARIATION OF FERRITIC INDUCTION AND PERCENTAGE OF FERRITE WITH COLD REDUCTION. Composition of Alloy: C, 0.08; Mn, 0.40; Si, 0.24; P, 0.014; Cr, 18.13; Ni, 8.94. 1. If ferrite is formed by cold-working austenite, what happens to the carbon with which the ferrite and austenite are both pre-sumably supersaturated? 2. What is the nature of the alpha-ferrite formed at grain boundaries by chromium-carbide precipitation at these boundaries?

Jan 1, 1939

By I. W. Wark

AN attempt has been made to compare the influences of the two most widely used depressants-alkalis and sodium cyanide-and the most widely used activator-copper sulfate-on the air-mineral contact induced by five sulfur-bearing compounds: (1) sodium di-ethyl dithio-phosphate (sodium Aerofloat); (2) potassium ethyl xanthate; (3) sodium di-ethyl dithiocarbamate; (4) potassium iso-amyl xanthate; (5) potassium di-n-amyl dithiocarbamate. Three different organic types are included in this group and for two of these types a higher and a lower homologue have been tested. The study of potassium ethyl xanthate, the preliminary results of which have been described,1 was continued until there had been obtained a comprehensive account of the influence of variations in pH value and in the concentrations of xanthate, sodium cyanide and copper sulfate on the adsorption of this xanthate by galena, sphalerite, pyrite and chalcopyrite. With concentrations of copper sulfate and collector that the work with ethyl xanthate indicated would give the most illuminating results, the other four collectors were tested in a less exhaustive way. The same general principles determine the influence of alkalis, cyanide and copper sulfate, no matter to which type the collector belongs, but there is a gradation in the quantitative measure of such influence. In the list above, the five collectors are cited in the order of their capacity to withstand the depressants, sodium Aerofloat being the least resistant, potassium di-n-amyl dithiocarbamate the most resistant. This order coincides substantially with that of the solubilities of the heavy metal salts formed by double decomposition with the collectors, those formed from sodium Aerofloat being most soluble. There is little difference between the third and fourth members of the series, and under certain conditions their positions are reversed.

Jan 1, 1934

By W. D. Robertson, H. Conrad

Incremental loading creep tests were conducted on magnesium single crystals in tension and direct shear at 78" to 364°K. The creep curves were transient in character and exhibited waves or periodic behavior, especially at small strain rates. A sigmoidal curve was frequently observed following the first occurrence of creep. Repeating of segments of a master curve was observed at all temperatures indicating that identical conditions for flow existed after various stress and strain histories. A logarithmic time law with a independent of temperature whs observed at 78°and 203°K, while a parabolic (power) time law was approximated at 298" and 364°K. The departure from logarithmic creep was attributed. to recovery, which was observed at 298" and 364°K. The temperature independence of a represents a serious objection to the theory of low-temperature creep based on the intersection of dislocations. IN a previous paper1 it was found that the initial creep rate of magnesium single crystals, y, following the addition of a stress increment in the range of 78° to 364°K, was given by the expression ? = C exp - {?H/kT} exp {B(T- h ?)} [1] where B and C are constants, AH is an activation energy of 10,300 cal per mole, T is the applied stress, ? is the total strain at the time of the stress increment, and h is the strain-hardening coefficient. The present paper is concerned with certain other features of creep behavior observed during this investigation; namely, the form of the creep curves, time laws for creep, recovery, and microscopic and X-ray observations of the structural manifestations of the creep flow. To the authors' knowledge the temperature range of the present investigation (0.08 Tm to 0.40 Tm) has not been covered previ-

Jan 1, 1959

By P Shenon

THE Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people.1 Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties.

Jan 1, 1934

By H. K. Martin

IN September 1954 the Lavender pit concentrator at Lowell, Ariz., began treating low grade porphyry copper ore from the nearby Lavender mine. Nominal capacity of the mill is 12,000 tpd, but production now averages 16,226 tpd. Plant design was somewhat affected by the re-use of old equipment and the substantial re-use of old buildings. A breaking-in period between June 24 and Sept. 1, 1954, was devoted to training operators and making minor changes in launders, chutes, and piping. From Sept. 1, 1954, to July 1, 1956, the mill treated 8,598,105 dry tons of ore, from which 556,541 tons of concentrate were produced, containing an indicated 144,055,185 lb of copper.

Jan 11, 1957

C. W. GOODALE, Butte, Mont. (member of the committee)- (communication to the Secretary*).-In the discussion of papers presented at the New York meeting of the Institute in February, 1915, and at the Arizona meeting of September, 1916, I referred to the activities of the Bureau of Safety of the Anaconda Copper Mining Co., and I am now submitting a few thoughts by members of the staff of that Bureau. TORGUS H. OAAS, Safety Engineer, Butte, Mont.-The report of the Committee on Safety and Sanitation has described different organizations and methods of promoting safety work. The effectiveness of these methods would aid the beginner in his campaign for safety in choosing the kind of organization and methods best adapted for his field. This can he obtained only by a discussion by those who have long promoted this kind of work, and have met with successful results. As the field is new, the different organizations promoting safety work have not established a common basis of rating for their fatal, serious and slight accidents, so that it is now difficult to get a comparative basis from which to judge the merits of the different systems. C. W. GOODALE.-The U. S. Bureau of Mines adopted, at the beginning, as a basis for its yearly summaries, the number of accidents. per 1,000 men employed, and it is now (quoting from its report for 1915, Technical Paper 168) making the following "classification of injuries:" "Many of the States now have. compensation laws, and in order to conform with their classifications, the bureau's classification of serious and slight injuries for 1915 is on a 14-day (2-week) basis instead of 20 days, as in previous years. The new classification of injuries includes three types, as follows: 1. Fatal 2. Serious (time lost, more than 14 days) (a) Permanent disability Total Partial

Jan 6, 1917

By B. T. Brady

Experimental data 1,2 on the energy dissipation in polycrystalline materials over a large frequency spectrum (10-2 cps to 106 cps) suggests that the quality factor [(e= Q )] is independent of the frequency providing both fluid-saturated and ferromagnetic materials are excluded from the test data. Additional data 3 suggest that the quality factors are less at high pressures than at low pressure, i.e., Q increases as the pressure increases. Observations on the dissipation of single quartz crystals with their polycrystalline counterparts indicate that the energy dissipation is less for the single crystal than for the aggregate .2 Both of the above observations, particularly the latter, are indicative of the fact that the dissipation increases with increasing surface contact within the polycrystal, i.e., a frictional attenuation scheme may be operative. Knopoff and MacDonald 4 have shown that a friction model gives rise to a quality factor frequency independence property. A partial listing of some values of Q, observed for both metals and non-metals, is given in Tables I, II, and III. In Tables I and II, the data all show Qs>Qp, i.e., the energy loss per cycle for compressional body waves is greater than that for shear waves of the same frequency. Most samples in Table III show the same effect. It is objective of this paper to suggest: (1) a frictional attenuation scheme may account for the observed losses incurred during the propagation of low amplitude stress waves in dry brittle rock and, in particular, that such a scheme can account for the observed relative magnitudes of the quality factors for P and S wave motion; (2) a friction scheme can readily explain the difference between the dynamic and static moduli in dry brittle rock; (3) a friction scheme, while in itself an intrinsically

Jan 1, 1968

By C. M. Schwartz, A. P. Young

ZIRCONIUM is noticeably embrittled at room temperature by hydride precipitate not only in notch-impact tests but also in tensile-impact tests.' The embrittlement in slow-strain tensile samples is much less severe. To understand better the relationship of the hydride precipitate to the strain-rate effect in tensile samples, the surfaces of chemically polished zirconium tensile samples strained at a slow rate (0.03 in. per min head speed) and at an impact rate (18.1 fps hammer speed) were examined in the light and electron microscopes. Vacuum-degassed samples and hydrogenated samples (100 ppm hydrogen) were examined. The hydrogenated samples were slow cooled from 800°C. The most apparent difference between slow-strain and impact tensile samples was the preponderance of twinning over slip in impact samples as opposed to relatively little twinning in slow-strain samples. The twin bands in hydrogenated samples often terminated on hydride needles as seen in Fig. 1. Almost opposite the twin terminus is a fine crack and a nearly round fissure. Holes near the areas where single lens-shaped twins or opposing pairs terminate on hydride particles also could be seen In the light micrbscope. Quite frequently, microcracks associated with a partial row of hydride particles were visible, as in Fig. 2, indicating that the crack was parallel to a row of hydride particles. Some samples were chemically polished after straining to remove metal with a minimum of disturbance of internal voids. Fig. 3 shows a crack in the interior of a hydrogenated impact sample. Holes along grain boundaries were seen after impact in both degassed and hydrogenated samples. Very few microcracks were seen in degassed samples after impact or slow strain, or in hydrogenated samples after slow strain.

Jan 1, 1959

By Joseph L. Gillson

BRAZIL has had an industry based on ocean beach deposits of heavy minerals containing monazite, zircon, rutile, and ilmenite for well over 40 years, but except at the very earliest period, prior to 1906, and again during World War 11, has this industry been at all comparable in size with similar operations in other countries. Limiting factors have been neither a lack of reserves nor lack of markets (except for zircon). Although poor local transportation and shipping facilities have handicapped the development in Brazil, these conditions were perhaps equally bad (when mining operations started) in the Indian State of Travancore, and in New South Wales and Queensland, Australia, in which states the principal production of beach deposits of heavy minerals has occurred. The outstanding restraints on the Brazilian industry have been the lower quality of the Brazilian minerals, the relative small size of individual deposits that were known until recently, the lack of interest of Brazilian investors in mining ventures, and the unfavorable climate for investment of foreign capital under Brazilian mining law. The lower quality of the minerals is indicated by the fact that the Brazilian monazite carries only 5 to 6 pct ThO2,*, and the ilmenite 56 1/2 pct TiO2, whiteness of the Australian zircon. An inadequate market for the abundant zircon that will be avail- able in any operation in Brazil is certainly a heavy restraint, since otherwise it could be an important byproduct. The oxide of zirconia, baddeleyite, that has come from Brazil is from other sources. 1 Since the Brazilian beach sands carry only a little rutile, that mineral has not been available as a valuable byproduct to help finance the operations.

Jan 6, 1950

(The following-list contains the names of those members of the Institute of whose connection with military service we have only recently. become acquainted.) ADAIR, ARTHUR C., Corporal, 4th Co., 1st Tr. Bn., 154th D. B., Camp Meade, Md. BATCHELOR, STILLMAN, 1st Lieut., Co. 6, E. 0. T. S., Camp Humphreys, Va. BATES, BENNETT R., 1st Lieut., Engineers, Co. 3, E. 0. T. S., Camp Humphreys, Va. BJORGE, GUY N., Co. 3, E. 0. T. S., Camp Humphreys, Va. BOAS, Ross, H., U. S. A. BRADLEY, . H., JR., Capt., 408th Engineers, Camp Cody, N. M. BRINTON, OWEN F., Capt., Engineers, U. S. A. BROWN, HAROLD C., 2d Lieut., A. S. A.P.

Jan 1, 1919

By L. P. Teas

The year 1931 has been one of unusual interest in Gulf Coast petroleum development, not so much because of the number of new prospects discovered, for apparently none of any present distinction have been found, but because of the discovery of so many new oil fields and the proving of so many old prospects. During the year 10 new oil fields have been found on the Coast; five in Louisiana and five in Texas. Two suspected salt domes were proven by the drill. Production dropped from a daily average of 192,000 to 162,670 bbl., or an average of 58 bbl. for each producing well, and active operations from 189 to 119. During 1931 the Coast produced approximately 48,600,000 bbl., or 44 per cent less than in 1930, when 86,500,000 bbl. were produced. The daily return at the beginning of the year was $192,000 and at the end only $126,780, the price having dropped from $1 for A grade and a range of $0.75 to $1.22 for B grade to a price range of 70 to 86c, or an average of 78c $ per barrel at the end of 1931. The average Coastal well produced 17,400 bbl. of oil during 1931. During the year development in the old fields has continued active at Barber's Hill only, although some work is in progress at Humble, Pierce Junction, Refugio and Pettus. Clear Lake is active but the large ownerships will prevent the "boom" type of field. Production is being held fairly steady at Barber's Hill and Pierce Junction, but has declined rapidly during the year at Refugio, Humble, and to a lesser degree at Pettus. The 6000-ft. production at Barber's Hill has shown a decided drop during the year and has not measured up to expectations.

Jan 1, 1932

By Donald C. Moore

INTRODUCTION Published laboratory procedures used by the major crusher manufacturers for estimating crusher size are based upon techniques developed in the mid 1940's. Specifically, the two largest U.S. crusher manufacturers are using the Bond impact procedure. Although the procedure is still in use, there is little confidence in the results. Unless the laboratory results fall within a preconceived range, personal experience is used for selecting the number of crushers and connected horsepower (Coleman, 1978). There have been numerous theoretical studies of the communition of particles. However, no procedure has been widely acclaimed for predicting crusher power requirements. Experimental studies have included breakage by slow compression, slow speed impact and high speed impact. Theoretical results have increased our knowledge of the comminution process, but the procedures have not been capable of analyzing the complex mechanism of industrial crushing machines. The purpose of this chapter is to review the empirical crushing procedures that have been used, including advantages and disadvantages. A new procedure which has been in development at Allis-Chalmers Corp. from 1977 to 1982 is detailed. Actual results of the new procedure on a concentrator feasibility study are included. EXPERIMENTAL GOALS The goals of a laboratory crushability procedure are accurate predictions of: (1) Rock crushability, measured as energy per unit mass. (2) Crusher product size analysis. A procedure capable of predicting these parameters should be inexpensive and require a minimum amount of sample. CRUSHABILITY TESTS Bond Impact Procedure F. C. Bond (1946) detailed the development of the pendulum impact device that is still used by the leading crusher manufacturers (Bond; Rexnord, 1976). The device (Fig. 1) is comprised of two bicycle wheels with 13.6 kg steel hammers tangentially attached to the rims. The hammer faces are 50 mm apart at rest. On opposite ends of the hammers lifting

Jan 1, 1982

By S. H. Gelles

Samples of poly crystalline zinc of 99.999+ pct purity were observed metallographically after having been exposed to hydrostatic pressures of up to 27 kbars. The deforrnation produced by this treatment was analyzed using X-ray and metallogaphic techniques. Basal-plane slip occurred universally in all grains exumined at the lowest pressure used (8 kbars). At pressures of >23 kbars, {1012} twin nucleation and growth were noted as well as slip. Formation of bend planes, complex kink bands, and recrystallization at the gain boundaries were also observed in this pressure range. These observations are discussed in reference to the expected deformation behavior of zinc under high hydrostatic pressure. It has been shown over the past few years1'3 that anisotropic, poly crystalline metals can be made to deform plastically by the application of a hydrostatic pressure. The effect is greater 1) the larger the anisotropy of linear compressibility and 2) the smaller the stress level needed to produce plastic deformation. Zinc having both very anisotropic linear compressibilities and a very low critical resolved shear stress (CRSS) for basal-plane slip has been shown to exhibit large amounts of plastic deformation when subjected to a hydrostatic pressure.2,3 At pressures up to 15 kbars, grain boundary migration and slip on one set of glide planes have been reported.' After exposing samples to 20 kbars pressure, grain boundary migration, single slip, multiple slip, and twinning have been noted.' The identification of the deformation modes operative under these conditions has not been reported. It was the purpose of this research to identify the deformation modes induced in poly crystal line zinc by the action of a hydrostatic stress and to study the strain accommodation at grain boundaries. Hydrostatic pressure could affect the operational modes of deformation by altering the Peierls-Nabarro stress. This may be roughly approximated by the relationship4

Jan 1, 1967

OF the many categories into which scientific knowledge has been arbitrarily divided, the one that has proved most applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. The many excellent textbooks of physical chemistry1 provide ample material on the principles of this subject for the student of steelmaking processes; yet with- out exception those texts draw the greater part of their illustrative material from room-temperature data. It is the purpose of this chapter to provide a concise review of the principles of physical chemistry that have proved useful in studies of steelmaking and at the same time to present some of the data that are essential to the application of physical chemistry to reactions at high temperatures. Certain parts of physical chemistry require rather formidable mathematics for their complete development but in the main those applications in which we are here interested can be ex- pressed in fairly simple terms. Many of the equations are logarithmic, and we shall use the symbols In X and log X to represent respectively the natural and the common logarithm of X. The two are related by In X = 2.303 log X. Logarithms may be read from a good slide rule with sufficient accuracy for our purposes. In a few spots a knowledge of the calculus will be, helpfu1. MATTER Innumerable forms of matter may be recognized, and these may be converted by chemical processes into others, as ore, coke, and air are converted into iron, slag, and gas. Whenever such a change occurs there is a corresponding change in

Jan 1, 1951

By Arthur F. Taggart, G. R. M. Del Giudice, M. Hassialis, A. M. Saddler

Flotation of sulphide minerals and native metals is no longer a practical difficulty. The underlying scientific principles of the method, although not explored in anything like complete detail, have been formulated with sufficient breadth so that the direction of attack on any specific case is clearly indicated. It has been known since the earliest days of flotation that certain of the nonsulphide nonmetal minerals—e.g., sulphur and graphite—would respond to flotation by oils as sulphides do; therefore they have been grouped with sulphides in many patents. But since the development of the chemical theory of collection,1,2,3 this similarity in action has been one of the facts cited in disproof of the theory by opponents of the hypothesis.4,5,6 Air levitation† of certain oxidized minerals, both metalliferous‡ and nonmetalliferous, and separation thereby from other oxidized minerals, is a recent development in practice, although the discovery of the method dates back 17 years7 This paper presents evidence that the principles underlying the air levita-tion of the nonsulphide nonmetal minerals are the same as those utilized in the flotation of the sulphides and native metals. It will be apparent immediately to anyone with knowledge of mineral concentration that separation of air-levitated minerals in water from minerals not so levitated is a simple matter of water-gravity concentration, the separating device employed depending solely upon the size of the particles treated and the buoyancy differences effected by the levita-tion. The usual separating means employed are: (1) a flotation machine for fine, slimy and for well aerated granular material; (2) shaking tables for granular less aerated material. By using large quantities of oil, it is possible to form substantially air-free oil-bound masses or granules of nonsiliceous minerals and to

Jan 1, 1939

By A. M. Saddler, G. R. M. Del Giudice, Arthur F. Taggart, M. Hassialis

Flotation of sulphide minerals and native metals is no longer a practical difficulty. The underlying scientific principles of the method, although not explored in anything like complete detail, have been formulated with sufficient breadth so that the direction of attack on any specific case is clearly indicated. It has been known since the earliest days of flotation that certain of the nonsulphide nonmetal minerals—e.g., sulphur and graphite—would respond to flotation by oils as sulphides do; therefore they have been grouped with sulphides in many patents. But since the development of the chemical theory of collection,1,2,3 this similarity in action has been one of the facts cited in disproof of the theory by opponents of the hypothesis.4,5,6 Air levitation† of certain oxidized minerals, both metalliferous‡ and nonmetalliferous, and separation thereby from other oxidized minerals, is a recent development in practice, although the discovery of the method dates back 17 years7 This paper presents evidence that the principles underlying the air levita-tion of the nonsulphide nonmetal minerals are the same as those utilized in the flotation of the sulphides and native metals. It will be apparent immediately to anyone with knowledge of mineral concentration that separation of air-levitated minerals in water from minerals not so levitated is a simple matter of water-gravity concentration, the separating device employed depending solely upon the size of the particles treated and the buoyancy differences effected by the levita-tion. The usual separating means employed are: (1) a flotation machine for fine, slimy and for well aerated granular material; (2) shaking tables for granular less aerated material. By using large quantities of oil, it is possible to form substantially air-free oil-bound masses or granules of nonsiliceous minerals and to

Jan 1, 1939