Search Documents

By V. C. Perini

The 1943 designation of districts for the Transactions† has caused some confusion because of the elimination of the West Central Texas district and the allocation of the counties of this district to the North Texas district and the North Central Texas district. The North Central Texas district as herein defined includes the counties of Brown, Callahan, Cole-man, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, San Saba, Shackelford, Stephens, Stonewall, Summerville, Taylor, Throckmorton and Wise. These counties as listed are the counties of District 7B, State Railroad Commission. This district covers the south central crest and the west flank of the Bend flexure north of the Llano uplift. The west flank of the Bend flexure is on the east boundary of the Permian Basin of West Texas. The North Texas district, District No. 9, State Railroad Commission, includes the counties of Archer, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger and Young. The area of this district covers the crest and south flank of the Red River uplift and the north central crest of the Bend flexure. The greater part of the oil and gas produced in the past from the North Central Texas district has been from Pennsyl-vanian strata. Some oil and gas has been produced from the lower Permian (by the latest selection of the Pennsylvanian-Permian boundary') and minor amounts from the Mississippian and Ordovician sediments. Increasingly important quantities of oil and gas are to be expected from the older sediments by deeper development in proven fields and by new discoveries. Most of the oil and gas in the district has accumulated in localized, well-defined structural traps in limestone and sandstone reservoirs and in traps due to stratigraphic changes in sedimentation, mainly porosity traps in limestone and sandstone lenses, both usually associated with some structural feature. The Stripper Well Premium Plan as adopted by the office of the Federal Price Administrator has been an aid to the producers of stripper wells. The producers are pleased to receive the subsidy to prolong the plugging of wells, but they are not too pleased with the subsidy plan in principle. Most independent operators are in favor of, and think they are entitled to, an increase in the market price for oil. The price is not adequate to meet the requirements of the average independent operator with the continued advance in production, development and wildcatting costs. Old and new pipe lines for oil and gas leading out of the state are removing reserves at an alarming rate. Curves showing the rate of discovery versus production and pipe-line deliveries in and out of the state make a cross that sooner or later will be fatal to the state. Wildcatting not only needs a price increase but every other available incentive and encouragement.

Jan 1, 1945

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By G. C. Fryburg, H. M. Murphy

ThE rates of oxidation of metals are usually obtained by heating the metal specimens in furnaces. Such a procedure is satisfactory for most metals. However, there are several metals that oxidize according to the reaction.

Jan 1, 1959

By Strathmore R. B. Cooke, Iwao Iwasaki, C. S. Chang

The effects of aeration on an aqueous suspension of pyrrhotite were studied and their results correlated with flotation tests using xanthates as collectors. The effects of copper activation and of pH variation were determined and possible mechanisms postulated. PYRRHOTITE has long been considered a gangue mineral to be eliminated as tailing in the treatment of various sulphide ores. However, in recent years the world-wide lack of sulphur resources has called attention to this mineral as a potential source of both sulphur and iron. Its importance as an economic mineral, however, has not been particularly emphasized. For this reason very little is known about its response to flotation, except that it can be depressed easily in alkaline circuit, by long aeration,1,2 addition of oxidizing agents,3 or by starch.' The object of this work was to study the floatabil-ity of pyrrhotite. This includes the effect of oxidation by aeration, of copper activation, and of change in pH. Preparation of the Pyrrhotite Sample: It was desirable that the highest grade of pyrrhotite obtainable be used for this experiment, since the presence of other minerals could affect the surface properties.5 However, no pyrrhotite was available as crystals, and massive deposits of hydrothermal origin commonly contain considerable amounts of chalcopyrite. Pyrrhotite concentrate was, therefore, prepared from a sulphide deposit occurring near Aitkin, Minn. The deposit is of pyrometamorphic nature consistirlg mainly of pyrrhotite and pyrite with graphite, silicates, and carbonates as gangue. The ore, already crushed through 3 mesh when received, was screened at 65 mesh and the undersize discarded. The oversize was crushed through rolls, and then stage-ground dry in an Abbe porcelain mill, the —65 mesh portion being screened out after every 15 min of grinding until all the material passed through this size. The ground product was then concentrated with a drum-type dry magnetic separator. The rougher concentrate was cleaned twice and then demagnetized. The final product was split in a Jones splitter and stored in air-tight bottles. Microscopic examination of the concentrate showed that it was relatively clean and free of pyrite, locked particles, and gangue. By means of the krypton gas adsorption method," the specific surface was determined to be 3000 cm2 per g. The chemical and screen analyses of the final concentrate are given in Tables I and II respectively. It is a well-recognized fact that the oxidation of some sulphide ores during stockpiling, grinding, and conditioning affects their flotation behavior. The problem of oxidation may become serious in the case of pyrrhotite, since this is known to be more easily oxidized than many other sulphides. To ascertain the extent of oxidation, an experiment was carried out by aerating an aqueous suspension of pyrrhotite with air, oxygen, and nitrogen as follows. A 300-g sample of pyrrhotite in 2700 ml of water was agitated and simultaneously aerated in a Fager-gren-type laboratory flotation machine. A Precision wet test meter was connected to the air inlet valve, the flow rate of the gas being kept constant at 0.3 cu ft per min throughout the experiment. Samples of approximately 30 ml each were taken from the cell at 0, 4, 10, 20, 35, 60, and 90 min. After the pH was taken, each sample was filtered and the filtrate was analyzed for total iron and sulphur. The iron was determined colorimetrically by the thioglycolate method using a green filter.' The filtrate was oxidized with bromine to convert all of the soluble sulphur compounds into sulphate and this was determined with a Parr turbidimeter." When aeration tests were made in alkaline circuit, calcium hydroxide or sodium hydroxide was added at regular intervals to maintain a constant pH. A similar procedure was followed in an experiment to determine the abstraction of copper. ion by pyrrhotite. In this case various quantities of cupric chloride were added. The filtrate from each sample taken was analyzed for copper, total iron, and sulphur. The carbamate method with a green filter was used for the copper analysis,' since this method could tolerate a considerable amount of iron in the solution. A pneumatic cell, made from a 350-ml fritted glass Buechner funnel, was used for this experiment. The detail of the assemblage has been described elsewhere." In the present work a stainless steel baffle was inserted in the cell. This baffle overcame the tendency for the coarse pyrrhotite particles to be swirled around the wall of the cell and thus fail to collect in the froth. A 50-g sample of pyrrhotite was added to the cell which contained 260 ml of water. When pretreat-ment of the sample was desired, reagents, such as activator and pH regulator, were then added and the pulp was conditioned for a specified conditioning time. Prior to the addition of the collector approximately 15 ml of the solution were removed for pH measurement and for iron and sulphur analyses. Copper when used as activator was also determined. Collector and frother were then added and the pulp was conditioned for an additional 2 min. Air was admitted to the cell and the froth removed. The separation required from 4 to 6 min, depending on the characteristics of the froth. The float and non-float products were filtered, dried, weighed, and assayed for iron.

Jan 1, 1955

By A. M. Johnson, M. M. Singh

The mechanism of failure under a drill bit is still improperly understood in spite of several investigations of the subject. Generally, the cratering process under static loading conditions is considered to be similar to that achieved dynamically by impact. This paper attempts to indicate that, although the sequence of fracturing in the two cases appear to be identical, at least some dissimilarities exist. For example, the width-to-depth ratios of the craters vary to some extent, and the amount of energy consumed per unit of volume of craters is unequal for the two different loading conditions. Prevalent rock penetration processes are dominated by methods utilizing mechanical attack on rock. It is, therefore, generally accepted that a better comprehension of the mechanism of rock failure under a wedge would prove beneficial towards improving present drilling techniques. Several attempts have been made in recent years to explain how craters are formed under a drill bit, but the mechanism of failure beneath a bit is still improperly understood. 1-11 Most investigators, to date, have inferred the sequence of events occurring during crater formation from analyses of force-time diagrams,1"6 from theoretical considerations,7 or from a study of the configurations of final craters.8-l0 These analyses have led to the presentation of widely divergent models for rock failure beneath a drill bit, ranging from brittle to viscoelastic. The cratering process under dynamic loading commonly is regarded as being similar to that obtained under gradually applied, or 'static', loads. But the effect of rate of loading on the action of a bit is still disputed. Some investigators11-12 maintain that there should be no such effects, whereas others have demonstrated experimentally that these exist.13-17' The purpose of the investigation reported in this paper was to examine petrographically the damage done to rock under the action of a chisel-shaped wedge, both with 'static' and dynamic loading, and to determine if rate-of-loading effects could be detected. Significant quantitative differences in crater volumes and depths were found to exist for a given consumption of energy. On the basis of this data, an attempt was made to indicate some of the rheological properties that a proposed model should possess. All the work reported herein was conducted at atmospheric pressures. EXPERIMENTAL APPARATUS AND PROCEDURE Two types of rocks were employed for most of the experiments reported in this paper, viz. Bedford (Indiana) limestone and Vermont marble. The mechanical properties of these rocks are given in Appendix A. Actually two types of Vermont marble were used, but since no marked difference could be discerned between the two varieties (as seen in Fig. 10) the data was used collectively for the analysis. Stronger rocks were not employed owing to difficulty in generation of observable craters without damage to the equipment. Six-in. diam cores were drilled from the rock samples and embedded in 8-in, diam steel pipe with 3/8-in. wall thickness, using hydrostone to fill the annulus between the core and the pipe. This procedure was adopted to confine the rock specimen so that fractures would not propagate to the edges of the cores. This goal was achieved satisfactorily for these tests because no cracks were observed to extend into the medium surrounding the rock, even when craters were formed only 1 in. from the rock core periphery. Three to four craters were formed on a core face, because the rock damage from any one crater generally did not appear to extend into the others. Whenever, interference between damaged areas around adjacent craters was suspected, the data was rejected for purposes of the analysis. The limestone and marble samples were tested with a 60-degree, wedge-shaped bit, 1 5/8-in. in length, made of tool steel. The bit shank had two SR-4 type electrical resistance strain gages, mounted axially, to record the force-time history during the loading operation. The static indentation tests were conducted using a 50-ton capacity press fitted with an adapter for drill bit attachment. See Fig. 1. The force exerted by the bit at any instant was measured with strain gages affixed to the bit shank. An aluminum cantilever, with two SR-4 strain gages mounted near its clamped end, was employed to measure bit displacement. Both sets of gages were included in Wheatstone bridge circuits,

Jan 1, 1968

By D. A. Kraai, S. Floreen

The effect of 1 to 50 ppm S on the ductility of nickel at 800° to 1400°F was studied. Results at each temperature showed a decrease in the reduction of area from approximately 95 to 5 pet over the sulfur range studied. Ductility varied with grain size, but only to a minor extent relative to the sulfiw effect. The effects of sulfur were completely offset by the addition of small amounts of magnesium. The results indicate that the "hot-short" loss in ductility is not an inherent property of nickel. Some possible mechanisms which cause the loss in ductility are described. MANY metals or alloys that normally possess high ductility exhibit a ductility loss at intermediate temperatures. This loss in ductility is often called "hot-shortness". Numerous examples of this phenomenon have been reported in the literature. Much of this work has been reviewed by McLean1 and by Rhines and Wray.2 To date there is no fully satisfactory explanation of the cause of this intermediate-temperature hot-shortness. It is generally recognized that impurities, and particularly impurities that form low-melting phases, can cause embrittlement. Examples of hot-shortness have been reported, however, where there were no obvious impurities present which would lower the ductility. Thus there has been some basis for believing that hot-shortness is an inherent property, and that even the purest metal would display a hot-short loss in ductility. This latter hypothesis was recently put forward by Rhines and wray2 based on studies of nickel and nickel alloys. In the discussion of this paper, however, Guard noted that high-purity nickel showed no hot-shortness.3 Thus there is reason to doubt whether pure nickel, or by inference any other pure metal, will inherently exhibit hot-shortness. The present work was initiated to determine the extent to which hot ductility was sensitive to very small amounts of an impurity element. If it could be demonstrated that hot-shortness could be induced by only minor amounts of an impurity, then it might be argued that hot-shortness in general is an impurity effect, and not a fundamental property of pure metals. The particular impurity studied was sulfur in nickel. The deleterious effects of sulfur are well- known. It is also well-known, and will be shown below, that additions of magnesium will render sulfur innocuous. When no such refining agents are added, however, the Ni-S system is a very useful one for studying the influence of small amounts of impurities. EXPERIMENTAL PROCEDURE Two heats containing -24 ppm S were vacuum-melted and small amounts of magnesium were then added under an argon atmosphere. These alloys were used to show the effectiveness of the normal magnesium treatment in overcoming the influence of sulfur. A second series of alloys with a sulfur range of 1 to 50 ppm was then prepared by vacuum melting nickel in alumina crucibles. No elements, such as magnesium, which tend to combine with sulfur were added. The higher sulfur contents were attained by adding nickel sulfide. Lower sulfur contents were prepared using a method in which the melt was oxidized under vacuum to produce the reaction S + 2O = SO2 These heats were subsequently deoxidized with carbon. Ten- to twenty-pound ingots were cast of all of the alloys studied. The compositions are given in Table I. The ingots were forged and hot-rolled to 3/4-in. bar. They were then annealed at either 2000" or 1600°F to produce different grain sizes. One-quarter-in.-diam tensile specimens were machined from the bars. These were tested at 800°, 1000o, 1200°, and 1400°F. The specimens were held at temperature approximately 45 min before testing. The strain rates were 0.005 min-1 to yielding, and 0.05 min-' after yielding. No extensometers or gage marks were placed on the specimens because the higher sulfur heats tended to fracture at the knife-edge indentations or gage marks. The properties measured were ultimate tensile strength and reduction of area. The analytical technique for determining sulfur at low levels was that developed by Burke and Davis.4 They reported a standard deviation of 1 ppm at an average sulfur level of 4 ppm in NBS standards. A standard deviation of 3 ppm is probably more realistic for the alloys used in this investigation considering the possibility of some segregation in the ingots. RESULTS A summary of the tensile results is given in Table I. As shown in the table, both heats to which

Jan 1, 1964

By Jim F. Lemons

INTRODUCTION A nickel doesn't buy much anymore. That's even true in the cost of recovering nickel -- the commodity. A 5[C] per pound (11 [c] per kilogram) increase in the nickel price won't cover a 10-percent increase in fuel costs for processing laterite ores, nor will it cover a 10- percent increase in wages for recovering nickel from a sulphide ore. It won't even cover a 5- percent increase in the capital cost necessary to mine and process ocean nodules. The basis for this statement and a quantitative analysis of the variations in costs to recover nickel from different types of nickel ores will be discussed in this paper. During the early part of the 1970's, the interest in nickel and its potential development was shifting from Canada to the Pacific Basin area. Canadian growth rate was slowing and each additional increase in nickel capacity was very expensive (Argall, G.O., 1970). Laterite ores were attractive to developers since they were easy to mine at a low labor cost, and technologies were being developed that would allow the recovery of nickel in marketable forms (Mohide, T.P., Warden, C.L., Mason, J.D., 1977). During the last decade, new laterite production was achieved in the Philippines and Botswana, and a significant increase in production from Indonesia and New Caledonia occurred. However, recent reports on nickel identify numerous problems plaguing the industry, i.e., high energy costs that are forcing shutdowns (INCO, 1980), (Mohide, T.P., Warden, C.L., Mason, J.D., 1977), high Canadian sulphide mining labor costs (Anon., 1976), and rapid inflation of nickel capital costs (Anon., 1981b). No definitive study has been made to determine how sensitive the total cost of production is to rising energy, labor, or capital costs, or to identify to what extent increased byproduct revenues could be used to offset these production costs. The purpose of this paper is to quantify the effects of increases in energy, labor, capital costs, and by-product credits on the future cost of production from nickel reserves and/or resources. METHODOLOGY OF ANALYSIS In order to evaluate the sensitivity of nickel production costs to changes in energy, labor, and capital costs, and in byproduct revenues, an analysis was made of existing and proposed nickel operations, their costs, and their sensitivity to change. The data for these analyses were obtained from numerous sources including international govern¬ment and university publications, professional journals, company reports, private communications, U.S. Bureau of Mines contracts, and estimates by Bureau of Mines personnel. These data were collected, in part, as an ongoing effort of the U.S. Bureau of Mines Minerals Availability System (MAS) to systematically measure and classify identified mineral resources according to their respective extraction technologies, economics, and commercial availability. The MAS Program is currently evaluating the present and potential availability of nickel to the United States in relation to mining, beneficiation, smelting, refining, leaching, transportation, infrastructure, environment, land use, labor, productivity, technology efficiencies, operating capacities, deposit life, and political factors. As a summary of this data, the following briefly describes nickel ore types as each relates to energy, labor, capital, and byproducts. Sulphide Operations Nickel is currently available from sulphide deposits. Roughly 55 percent of the current world nickel production in market economy countries is from sulphide ores, although only about 20 percent of the known land-based nickel reserves and/or resources are sulphides (INCO, 1981). In 1979, the Western World sulphide reserves were estimated at about 9.2 million metric tons of nickel (Little, A.D., 1979). Sulphide ores are typically mined underground, thus resulting in high mining costs; however, these ores can often be upgraded by flotation prior to final nickel recovery and require about one-third of the energy required to recover nickel from laterites (Anon., 1981c). In addition, nickel in sulphide ores may be associated with economically recoverable byproducts, which include copper, cobalt, gold, silver, and other precious metals. Laterite Operations Forty-five percent of current nickel production is from laterite deposits. Laterite deposits account for 80 percent of the known land-based nickel reserves and/or resources (INCO, 1981). In 1979, the Western World laterite reserves were estimated at over 35 million metric tons of nickel (Little, A.D., 1979). Nickeliferrous laterites are residual soils formed by weathering, typically under tropical or near tropical conditions. They can be easily mined by open-cut methods, but generally cannot be beneficiated; thus, recovery of nickel must entail processing of the total mined ore. Usually, these ores have high moisture content (20 to 30 percent by weight) that result in additional fuel costs to dry the ore. Nickel silicates, garnierites, are, processed by pyrometallurgical methods; limonite nickel oxides are normally leached. Byproduct cobalt is not recovered from most ferronickel operations, and is only recovered to a limited extent from many leach operations.

Jan 1, 1982

By Harry H. Angst

The history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. 'She elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,090 tons of 012 and 18,000 tons Of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4½-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. Equipment On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-diii~lp trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4½-cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1943

By Harry H. Angst

The history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. 'She elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,090 tons of 012 and 18,000 tons Of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4½-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. Equipment On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-diii~lp trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4½-cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1943

By John G. Reid

Subsequent to extensive laboratory testing, a pilot plant was constructed to further evaluate the process for high temperature copper cementation on iron in continuous operation. The plant was designed to produce 1 to 10 tons of copper a day depending on the copper concentration of the pregnant solution. The energy required to operate the plant was very low as virtually all the solution heating requirements were supplied by the exothermic cementation reaction. The results demonstrated that this, process has potential for commercial application with respect to operating considerations, and yields a copper product in excess of 95% copper at high reaction rates, low iron consumption, and at least 98% copper recovery from solution.

Jan 1, 1976

By Cyril Smith

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization.

Jan 1, 1935

By N. A. Gokcen, R. A. Dodd

Solubility of nitrogen in liquid iron-manganese system at 1550°C and one atmosphere pressure has been determined by a simple method. Results show that the solubility increases from 0.040 pct for pure iron to 1.41 pct for pure manganese. DETERMINATION of the solubility of gases in volatile metals. and alloys by the well-known Sievertsl method is unreliable. This is particularly true for the Fe-Mn system since Mn vaporizes readily from the alloys containing as little as 2 pct Mn, and, upon condensing on the cooler parts of the apparatus, it absorbs large amounts of nitrogen. Further, the condensing Mn vapor interferes with the usual method of temperature measurements with an optical pyrometer.

Jan 1, 1962

By R. E. Collom

VARIOUS chapters already written in the history of development of the North Dome of Kettleman Hills are monotonously identical in the one underlying theme of conservation of oil and gas. Discovered on Oct. 4, 1928, by Milham Exploration Co. with its wildcat Elliot No. 1, the field has been subjected to practically every modern form of produc-tion restraint in the name of conservation. The record thus far developed shows that conservation was had for a time, at a price; and that unitiza-tion must he blessed by single ownership or 100 per cent participation to be effective. In fact, incomplete unitization places a heavy handicap upon its participants in the competitive development that follows.

Jan 1, 1937

By D’Arcy A. Shock, J. G. Davis

Continental Oil Co. has spent more than four years of research on the fundamentals of recovery of potash by solution mining. This work included laboratory investigations of salt solution, brine flow, selective extraction of KC1 from sylvinite, and control of cavity geometry. Laboratory results were expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multiwell mining systems were studied in the field work. This paper discusses one field test in which potash was solution mined from a thin sylvinite ore zone in the Carlsbad Potash Basin. A two-well mining system was used for this test.

Jan 1, 1970

By R. A. Wyman

KYANITE schists in the Sudbury area have been generally described by Haw,1 who has also given particular information on preliminary treatment of three large samples from Dryden township, Ontario.2 Kyanite, garnet, biotite, quartz, and feldspar comprise the main ingredients of this ore. Kyanite is the valuable mineral. About 5 ½ tons of -35 +200 mesh product, made by dry rod milling, screening, and separation on the Exolon magnetic separator, were available for treatment by flotation. Magnetic separation had effectively reduced garnet and biotite so that flotation feed consisted essentially of kyanite, quartz, and feldspar, the kyanite content averaging 32 pct and representing about 86 pct of the kyanite in the original ore.

Jan 1, 1958

By J. R. Billingsley

The Sunro mine, operated by Cowichan Copper Co. Ltd., under lease from Sunro Mines Ltd., a Cominco subsidiary, is located on the south end of Vancouver Island. Exploration and limited development before 1960 established the existence of twelve mineralized zones. The "B" and "C" orebodies of the River zone contained an estimated 937,000 tons of 1.80r/, copper plus approximately 35 cents per ton of precious metals. On reviewing the indicated tonnage and the exploration possibilities in the River zone and the other eleven zones it was decided to construct a 1500-tpd mill. In August 1961, excavating of chambers for a crushing plant and concentrator located underground near the River zone began.

Jan 12, 1963

By H. M. Callaway

There are key words common to Government and the minerals industry, the use of which immediately spark interest, argument and confusion. Among these is productivity, a term ranking for widespread misunderstanding with mineral self-sufficiency and mineral conservation. Each interpretation of these words tends to emphasize a single aspect and either minimize or ignore the complex dynamic system of things that influence the Nations mineral productiveness. This paper1, abstracted from a monograph on lead now being prepared for publication by the Bureau of Mines, not only sheds light on the trend of productivity in the lead-zinc mining industry but it presents the basis for forming a common general notion of what the term productivity implies.

Jan 11, 1961

By Bayard Morrow

THE copper-bearing ores concentrated at the Anaconda plant of the Anaconda Copper Mining Co. are principally a mixture of copper and iron sulfides associated in a gangue consisting of quartz, lightly altered granite and feldspars, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. The predominant sulfide is pyrite. The copper minerals present are: chalcocite, bornite (Erubescite), enargite, chalcopyrite, covellite, tetrahedrite and some tennantite. Normal concentrator practice removes a slime prior to ball-mill grinding. The deslimed ore is ground to approximately 10 per cent plus 65 mesh for flotation. Two selective flotation circuits are used, one for deslimed ore and one for slime. The metallurgical results obtained are shown in Table 1.

Jan 1, 1933

By M. N. Nabighian, J. R. Odekirk, D. M. Hausen

Preliminary investigations based on the concept of cross-power indicate that quantitative volume percentages of minerals, including quartz, orthoclase, plagioclase, fluorite, and chalcopyrite can be obtained by X-ray diffraction analysis. Pulverized samples are scanned from 4° to 65°, 2e, using a Norelco diffractometer, with the output recorded on a punched tape at 40 intervals per degree, 29. Errors from crystal orientation are minimized by (1) gridded surface packing, (2) sample spinning, and (3) quantitative measurement of all major diffraction peaks. Computer programming enables rapid quantitative evaluation of X-ray diffraction data. Results to date indicate that most minerals analyses can be performed within an accuracy of ±2%. Metallurgical applications include analysis of various flotation concentrates and tailings.

Jan 1, 1973