Search Documents

By J. T. Crawford

Although nearly 10 pct of the total tonnage of coal produced annually within the United States is handled by bulk freighters on the Great Lakes, very little of the detail connected with it has been published other than occasional newspaper stories and publication of tonnage statistics. Of the total tonnage floated on the Lakes each year some 10,000,000 is stored and distributed from the port of Duluth-Superior, at the western end of Lake Superior commonly known as the Head of the Lakes. This port has the largest single area concentration of coal docks in the world. Since this area contains the largest ore docks, the largest movable material handling bridge, the largest and highest grain elevator and the largest coal bri-quetting plant in the world, it is entirely fitting and proper that here also should be located the largest coal dock and what we believe to be the world's largest clam shell. Of the sixteen coal docks operated by ten companies, five are owned and operated by the North Western-Hanna Fuel Co. which has two docks on the Superior, Wis., waterfront and three docks in Duluth, Minn. It is with these five docks that we are primarily concerned, General History In the summer of 1871 a small sailing vessel entered the harbor of Duluth-Superior with the first commercial coal cargo. All the coal brought up that first year did not amount to more than 3000 tons. During the year 1877 the first dock equipped for handling coal was built in Duluth. Coal receipts increased to 52,785 tons in 1879 the first year for which an official record was kept. Since then the volume of water-borne coal to the Head of the Lakes steadily increased to a maximum of 12,688,321 tons in the year 1923. This tonnage was nearly equalled in the year 1927 and the next highest tonnage recent year was in 1946 when 10,105,703 tons were unloaded. The average annual bring-up over a ten year period 1938 to 1947 was 8,605,231 tons. Approximately 30 pct of the coal unloaded at the Head of the Lakes is handled over the docks of the North Western-Hanna Fuel Co. Competition of other fuels coupled with expansion of coal fields in the mid-west have held coal receipts for Duluth-Superior at a relatively constant figure during the last eight years although the total tonnage of coal floated on the Great Lakes has more than doubled in the past 25 years. From the shovel and wheelbarrow method of unloading early cargoes to the horsepowered windlass derrick with a wooden tub was but a short step. The first movable coal handling, steam operated,

Jan 1, 1949

By R. H. Hadfield

Professor ArnolD, of the Sheffield Technical School, who has done so much excellent work in metallurgical research, recently produced, with the aid of aluminum, a sound ingot and bar from the purest known Swedish brand containing 99.8 per cent. of pure iron. Table 1. shows the physical quantities of this metal. TABLE I.— Tests of a Sample of Almost Pure Iron Prepared by Professor Arnold from D. v Ewedish Bar, Containing Before Fusion 0.04 Per Cent. of Carbon. I. II.+ III. Series mark,.. 136 1.371F ...... C, 0.07 0.07 Si, 0.04 0.04 8, 0.02 0.03 ...... Analysis, per cent,. .. P, 0.02 0.015 ...... Mn, 0.06 0.07 Al, 003 ............ Fe, 99.76 99.81 ...... Specific gravity,........... 7.863 ...... Original diameter, inches,. .. 0.564 0.798 0.798 Original area, square inches,. . 0.25 0.50 0.50 Limit of elasticity, tons per square inch,...... 18. 3.8 Breaking-load, tons per square inch,. 21. 23. 14.75 Total elongation, per cent., measured on 2 in.,...... 50. 49.25 61. Total reduction of area, per cent.,. 80. 69.60 61.20 Extension at permanent set, per cent.,...... 0.007 ...... silky and Appearance of fracture,. .. . silky i granular in parts.

Jan 1, 1894

INTRODUCTION Data available on prophyry copper occurrences in the Andean, Caribbean, Appalachian, and Cordilleran orogens may be categorized in a manner to suggest a hypothetical evolution for deposits that occur in the western hemisphere. A classification of de- posits is also suggested. A classification dependent on internal structure of a porphyry copper deposit would lead to two broad categories, breccia pipe and stockwork models. A classification of this type is examined herein but it is not universally accepted in the literature. Modeling based on igneous petrography as well as metasomatism attendant with the sulfide mineralization is more widely accepted by economic geologists whose evaluation of porphyry systems is influenced by the presence or absence of a phyllic zone. Lowell and Guilbert model deposits ordinarily include a phyllic zone, whereas those of the diorite model do not. Position of the phyllic zone in the alteration sequence is a significant ore guide. Should the phyllic zone be absent, dependence on alteration zoning to identify metallization is weakened. Presence or absence of the phyllic zone therefore is a significant parameter in the economic evaluation of a porphyry copper deposit (Hollister. et al., 1975). The Lowell and Guilbert (1970) model commonly includes a phyllic zone in quartz- bearing rocks. Parameters of both calc-alkalic and the quartz monzonite models mentioned elsewhere in this volume are sufficiently close to the Lowell and Guilbert (1970) model that it should be expanded to encompass them. The diorite model remains separate and distinct because deposits of this type are characterized by an absence of quartz in the pluton, commonly highly gold: copper ratios, low molybdenum content, and regular absence of sericite in the alteration zones. Therefore, for the benefit of those

Jan 1, 1978

By Ursula E. Wolff

Il.lechanica1 twins have been observed in brigsten single crystals of a variety of axial orientations defornzed at room temperature in tension or bending. The twins formed near the final fracture and were up to 3 p thick. The twinning plane was always of the type (113). Twinning at room ternperature occurred only after considerable prior slip. Twins usually preceded fracture and nucleated cracks. The crack surfaces often alternated between a (001) plane and the twin interfaces. Secondary twins could also nucleate from cracks. In the absence of twinning tensile samples failed by shear; twinned samples failed by cleavage. On the assumption that observed sudden load drops in the stress-strain curves are associated with twinning, a critical resolved stress for twinning of 60, 000 to 65, 000 psi was calculated. MeCHANICAL twinning has been observed in iron and iron alloys at low temperature by a number of investigators.'-7 Similarly, for high-purity tungsten, twinning has been reported for deformation temperatures below 211°K.8-10 In W-Re and Mo-Re alloys, 20 pct Re was determined as the lower limit for twin formation at room temperature." Since the twins are generally very narrow, they are usually identified only by etching techniques. The expected (112) habit plane has always been confirmed by angular analysis of the surface traces. Recently, however, a complete identification by X-ray analysis has been performed on twins in a Mo-35 pct Re alloy.12 During an investigation of the deformation charac- teristics of tungsten single crystals, twins were revealed in tensile and bend samples deformed at room temperature. This paper deals with the conditions for such twinning and the relation of twinning to fracture. EXPERIMENTAL PROCEDURE Tungsten single crystals, 1/8 in. in diam, of a variety of axial orientations were grown from un-doped material by four-pass electron-beam zone melting. A representative analysis is given in the following table: From these crqstals, tensile samples with 1 in. gage lengths were made by surface grinding, leaving shoulders for gripping. The diameter after grinding was 0.082 in. The distorted surface layer was then removed by ele1:trolytic polishing which reduced the diameter of the gage length to 0.080 in. Tensile tests were carried out at room temperature in an Instron machine under two different sets of conditions: a) Rigid mounting; strain rate 0.02 in. per in. per min. b) Gimbal mounting; strain rate 0.002 in. per in. per min up to a total strain of approximately 0.2 pct, then 0.01 in. per in. per min to fracture. Stress axis and growth direction coincided in all samples and are subsequently called orientation.

Jan 1, 1962

By H. C. Fiedler

The solubility of sulfur in Si-Fe was determined by the metallographic examination of heat-treated and quenched samples. In the absence of manganese, the solubility in 3.1 pct Si-Fe was found to be about 0.010 pct at 1000o C, 0.015 pct at 11000C, and 0.020 pct at 1150°C, which is substatntially less than hitherto reported. Increasing the silicon content was found to decrease the solubility of sulfur, which is consistent with the increase in the activity coefficient of sulfur with increasing silicon content that has been reported for Fe-Si alloys. Manganese additions were studied in alloys containing 3.1 pct Si and between 0.013 and 0.015 pct S. At low manganese levels the solubility product of manganese sulfide was found to be lower than previously reported. THE solubility of sulfur in pure polycrystalline iron has been reported by Rosenquist and Dunicz1 and by Turkdogan et al.2 Samples were equilibrated in atmospheres containing different ratios of H2S/H2. Both groups of investigators found a solubility limit in y iron of 0.013 pct at 1000oC and 0.031 pct at 1200°C. In addition, Rosenquist and Dunicz1 found a solubility limit in a iron of 0.020 pct at 900°C. Ainslie, Hoffman, and seybolt3 found significantly higher sulfur contents in polycrystalline iron samples than in single-crystal samples after heating at 890°C in a sealed tube containing a mixture of powdered iron and FeS made with s35. Whereas the single crystals contained 0.013 and 0.016 pct S (± 0.005 pct), the polycrystalline samples contained between 0.016 and 0.026 pct S. Autoradiographs suggested that the excess sulfur in the polycrystalline samples was due to the segregation of sulfur in solution at grain boundaries. Ainslie and seybolt4 have reported on the solubility of sulfur in 3 pct Si-Fe. Their samples were sealed in capsules containing hydrogen and sufficient sulfur as cobalt sulfide to saturate the sample. After heat treating, the sulfur-rich phase on the surface was removed by abrading, and the sulfur content of the sample was taken as the equilibrium value for that temperature. Before the equilibrating heat treatment, the samples were heated to 1300°C to coarsen the grains. The resulting grain size, which was about 3/18 in. in diam, was considered sufficiently large to preclude a sensible increase in sulfur solubility due to grain boundary segregation. They reported the solubility to be 0.029 pct at 900oC, 0.063 pct at 1000oC, 0.076 pct at 1100°C, 0.122 pct at 1200°C, and 0.098 pct at 1300°C.

Jan 1, 1968

By C. R. Kuzell

INTRODUCTION KNOWLEDGE of the thermal capacity of gases is of great importance in making metallurgical calculations. The metallurgist is, frequently called upon to investigate and determine furnace efficiencies in which the heat carried into or out of the furnace by gases is a large item in the heat balance. Not only do such problems present themselves in the determination of furnace efficiency, but also in the study of the application of heat is accessory apparatus, such as stoves, regenerators, waste-heat boilers, driers,.etc. The thermal effect of the use of excess air in the combustion of fuel, the theoretical temperatures of combustion, the quantity of heat in hot blast at various temperatures, the effect of hot blast on furnace temperatures, are a few more examples of frequently occurring calorific problems involving gases. So many are the applications of the data on the heat capacity of gases that the subject merits careful study. The heat in a gas maybe due to its heat of combustion, if it is a combustible gas, and to its temperature. The latter is called its sensible heat and is the heat absorbed or evolved by a gas as its temperature is raised or lowered. The heat of combustion of gases is well established and is commonly known. The values can be found in almost any mcdern treatise on metallurgy. The sensible heat of gases has not been so well established because it is in most cases a function of the temperature, and the values of specific heats of gases over a wide range of temperatures have only recently been determined. It is the purpose of this paper to deal with the sensible heat of gases.

Jan 8, 1914

By Carl Tolman, LeRoy Scharon, Harold Powers

THIS paper presents geophysical and subsurface data observed in the vicinity of Shafts No. 1 and and 5 of the National Lead Co. lead mines at Fred-ericktown, Madison County, Missouri, see Fig. 1. The area selected is an excellent example to illustrate the close correlation between geophysical data and geological facts as revealed by drilling and mining. Such close correlations make geophysical applications appropriate to the development of known ore-bodies as well as the exploration for new orebodies. In the past, magnetic and shallow electrical resistivity observations were made over limited areas in the Fredericktown lead district by the Missouri Geological Survey, with favorable results. The first extensive magnetic and electrical resistivity surveys were started by the U. S. Bureau of Mines in May 1945 in two areas located northwest and southwest of Fredericktown, as shown in Fig. 1. The results of these surveys were reported in April 1948 at Denver, spontaneous-polarization surveys were made over the property of the St. Louis Smelting and Refining Co. at Fredericktown by Sherwin F. Kelly Geophysical Services, Inc. Aeromagnetic surveys were completed in 1948 over the Fredericktown quadrangle by the U. S. Geological Survey. Since 1945 geophysical surveys have been an important part of exploration programs in the Fred- ericktown district. Such methods, magnetic and electrical resistivity, are now serving as guides in the further development of known orebodies. On an irregular pre-Cambrian igneous erosion surface Lamotte sandstone of upper Cambrian age was deposited, partially filling the topographic basins, see Fig. 2. Above and conformable with the Lamotte sandstone lies the Bonneterre formation, a dolomite with locally interbedded thin dolomitic limestones and shales at its base. This formation also only partially filled the topographic basins. The Bonneterre was overlain by the Davis, Derby, Doe Run, and Potosi formations, which are principally dolomite. Uplift, tilt, and slight warping has allowed erosion and weathering to remove most of the sediments overlying the Bonneterre, and in many places, not far from the mine, the Lamotte sandstone is exposed. This erosion has also exposed areas of pre-Cambrian igneous rock. The Lamotte sandstone, having been deposited on an irregular pre-Cambrian surface, is extremely variable in thickness and ranges from zero where it laps the pre-Cambrian rocks to 250 ft thick in the deeper basins. In the vicinity of the mines the Bonneterre dolomite ranges from zero where it wedges out against the pre-Cambrian igneous rocks to 400 ft thick. The ore deposits occur as a bedded disseminated type1 and are chiefly composed of galena and pyrite with minor amounts of chalcopyrite and siegenite. Heavy pyrite and marcasite mineralization may be found throughout the Bonneterre formation. However, there is little or no apparent association of these iron sulphide bodies lying above the ore hori-

Jan 1, 1954

By C. L. Magee, H. W. Paxton

PREVIOUS workersl'% ave found that as-quenched ferrous martensites can be plastically deformed at low stresses. They have also found that the stress to obtain small strains can be significantly increased by aging at temperatures up to 150°C. This behavior has been interpreted in two ways: 1) that the deformation at low applied stress is due to internal stresses and thus the aging phenomenon is due to relaxation of the internal stresses;' 2) that the microdeformation arises through the motion of unpinned dislocations and the aging process is the diffusion of carbon to the dislocations to pin them.293 In a recent paper,4 we have shown that under certain conditions the dominant microdeformation mechanism of as-quenched Fe-31Ni marten-site-austenite aggregates is the transformation of retained austenite. Our results on resistance changes during deformation and temperature dependence of the deformation also established that, at temperatures above 300° K, the microdeformation was not due to this transformation. The purpose of this note is to report results of experiments which indicate that explanation 1 is appropriate for this deformation. All results presented here are from conditions where transformation does not make a measurable contribution to the microplastic deformation, in Fe-31Ni-0.002C, or in Fe-29Ni-0.02C-0.25Ti. The experimental techniques that were used for measurement of the plastic deformation are described4 and analyzed5 elsewhere. Fig. 1 shows the microplastic response of 100 pct austenite at 300" and 350° K. The microplastic response of an austenite-martensite aggregate is also given in Fig. 1 and it is seen that, after formation of martensite, the initial plastic deformation occurs at lower stresses. Thus, the softness is not entirely due to retained austenite—the quenched structure can be deformed at lower stresses despite the fact that the macroscopic strength is significantly higher. A result which allows a distinction to be drawn between the alternative explanations for this behavior is derived from aging experiments on the low-carbon alloy containing titanium. We have previously shown4 that the presence of titanium in this alloy reduced the free carbon to a sufficiently low level that thermal stabilization of the austenite-martensite transformation was not detected. Despite this, Fig. 2 shows that the microplastic response is decreased by aging treatments. A similar aging effect in Fe-ZONi, with some titanium, has previously been reported by . Thus, carbon is not necessary for the aging process and explanation 2 is at best incomplete. Since internal stress relief can occur independently of carbon (any temperature dependence of the flow stress can result in decreased internal

Jan 1, 1969

By M. D. Hassialis

THE claim is made in a number of patents1,2,3,4 that some compounds of the class known as aryl sulphides have collector properties. One of these patents generalizes the claim to include all aryl sulphides, whose generic formula is R-S¬R[=]-R’ (where x = r,2, . . . ), with the restriction that if the aromatic radicals R, R' contain substituent groups these groups may not contain nitrogen or oxygen. Moses, Hess, and Perkins cite as evidence for their claims the results of flotation tests on Anaconda and Miami copper ores using Biphenyl sulphide, ditolyl disulphide and dinapthyl disulphide as collectors. The use of alkyl sulphides as collectors has also been reported5 with the conclusion that the alkyl sulphides are better collectors than the corresponding aryl sulphides. The experimental work cited appears to confirm this contention. In order to test these claims with respect to diphenyl sulphide, a sample, purchased from the Eastman Kodak Co., was tested against Anaconda ore. The procedure followed was that of Moses, Hess, and Perkins. A sample of ore weighing 500 grams was placed in a laboratory ball mill. To this was added 220 grams of water, 0.06 grams of commercial diphenyl sulphide (1/4 lb. per ton of ore), and 0.8 grams of lime (3 lb. per ton of ore). The material was ground until 93 per cent passed a 65mesh screen. This pulp was diluted to 16 per cent solids. A sample of the diluted pulp was placed in a Minerals Separation type of laboratory flotation cell. After a 2-min. agitation period, pine oil was added and the froth collected for a period of 15 min. This test recovered 68 per cent of the copper, with a ratio of concentration of 6.8: 1. The tailing assay was 0.3 per cent Cu. Moses, Hess and Perkins attained a recovery of 75 per cent, with a ratio concentration of 12: 1. Although these results do not compare too well with those of Moses, Hess and Perkins, subsequent tests showed an improvement, as judged by vanning of the tails. It is concluded, therefore, that the patent results are confirmed. CONTACT-ANGLE TESTS In order to study the response of the various minerals, found in Anaconda ore, to commercial diphenyl sulphide, some contact-angle tests were made. Polished particles of bornite, chalcocite, chalcopyrite, pyrite and quartz were conditioned for 15 min. in a suspension of diphenyl sulphide in water. The concentration of this suspension was 0.284 grams per liter, this being the concentration of this reagent in the ball mill. The conditioned particles were rinsed with water (not rubbed with filter paper or boiled linen) and then tested against an air bubble in the bubble machine, with the following results: born-

Jan 1, 1943

By R. W. Guard

ALTHOUGH etching techniques have been developed for revealing dislocation sites in several metals and ionic crystals,h t is valuable to extend the technique to new metals. An etch pit method for nickel has been developed on the basis some suggestions of Dr. John R. Cuthill of the National Bureau of Standards who had observed etch pits in creep specimens of nickel. The etchant used was proposed first by wensch2 for revealing grain size in nickel. The present paper describes the evidence that the technique can be used to reveal dislocations and gives the conditions under which etching can be carried out. The specimens examined were vacuum melted high-purity Ni (99.985 pct Ni) and commercial "A" nickel (99.8 pct Ni). Both materials contained greater than 0.008 pet C and had been annealed in nitrogen or dry hydrogen at 1100o to 1200°C. This gave a grain size of 1.5 mm in the high-purity nickel and 0.050 mm in "A" nickel. Tensile specimens (0.254 in. diam) were deformed from 0.25 to 10 pct at room temperature and then heated for 1/2 hr at different temperatures from 400" to 900°C. The specimens were sectioned longitudinally then polished electrolytically in 60 pct H2SO4 and etched in 35 pct H3PO4 solution at 0.2 to 0.4 v for 30 sec to 3 min. The best method for setting the proper voltage for etching is to increase the voltage until gas bubbles are evolved vigorously from the specimen and then cut it back by 10 pct. It is necessary to heat the specimen above 500°C after deformation in order that etch pits will be formed. This "decoration" treatment permits carbon to segregate to the dislocation rendering them sensitive to etching. It was demonstrated that carbon was the decorating impurity by decarburizing some specimens in wet H2 at 1200°C. The susceptibility to etch pitting was lost following this treatment but could be restored by carburizing in contact with graphite. Some rearrangement of the dislocations in the as-deformed structure occurs on heating at 500oC and above so that the technique can not be used to study the nature of dislocation patterns in deformed specimens. Extended etching does not change the number of pits although the background becomes rough and the pits quite large. The polycrystalline specimens with various strains were examined after annealing at different temperatures. Typical patterns are shown in Figs. 1 and 2. In the unstrained specimen, Fig. 1, the density of pits is 2.5 X 10' per sq cm. All grains show pits regardless of their orientation although there is a

Jan 1, 1961

By Robert E. Thurmond

DISCOVERY of a commercial ore deposit has resulted from a program emphasizing geophysical techniques and concentrating upon exploration of alluvial-covered areas. United Geophysical Co. selected these areas as offering the best possibility of success, for here the surface evidence of ore deposits has been hidden from the eyes of prospector and geologist alike. Pima mining district, Pima County, Arizona, was selected for initial exploration. The project was successful in that a commercial ore deposit was discovered and proved through drilling and extensive underground development. A limited region of activity was chosen and library research was begun on available economic and regional geological publications relating to the mining districts. Field reconnaissance of those districts which seemed to hold exploration possibilities provided a general picture and ascertained the existence of alluvial-covered areas of interest. At the conclusion of the reconnaissance trips all data obtained were compiled, and the district which seemed to present the best exploration possibilities was selected by statistical methods. The statistical summary was based on the following considerations: Geological Factors: 1—type of intrusive, P—presence of favorable host rocks, 3—apparent intensity of mineralization, and 4—presence of favorable structure in covered or unexplored areas. Economic Factors: 1—past production from district or mine; 2—size, shape, grade, and type of ore deposit in the district; 3—ease of acquiring mineral rights; and 4—general development facility. Exploration Favorability Factors: 1—results to be anticipated from geological methods alone; 2—application of geophysical methods, namely, topographic conditions, surface interference, depth-size relation, physical property contrasts as related to ores or controlling structural features; and 3—drilling factors. Admittedly, many of these, factors do not lend themselves to absolute evaluation, but relative evaluation, subject to inaccuracies of personal judgment, is always possible. A relative scale from 1 to 10 was established for every factor, representing varying degrees of favorability. For each district a numerical evaluation of each factor was established and a numerical total determined. The obvious advantage of this scheme is that a more concise summation can be presented by numerical means than can be achieved by descriptive means. After a district had been selected as favorable, the first step was to carry out more detailed geological and economic studies to narrow down the areas of interest. The second step was to compile all available geological data from publications and add to these data by mapping where necessary. Geological interpretation and projection of structural or other control into covered or unexplored areas was made whenever logical. To determine the possibilities of geophysical application and to select a geophysical method, physical property contrasts were related to mineral assemblages and/or structural control. If geophysics seemed applicable, trial profiles were run crossing the area normal to the strike and spaced

Jan 1, 1955

By Benjamin Tillson

To MOST mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount f drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be so handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau f Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 5, 1921

By E. W. Pehrson, J. W. Furness

THE five charts presented here- with are part of an original group prepared by the U. S. Bureau of Mines showing the international trade in the principal metals and metallic ores. Charts 011 anti- mony, chromite, copper, lead, manganese, mercury, nickel, tin, tungsten, and zinc were published in the February, 1936, issue of the Engineering and Mining Journal. Those shown here include bauxite, aluminum, iron ore, pig iron, and the platinum-group metals.

Jan 1, 1936

By Robert McKay

THE practical study of corrosion requires consideration off its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as. a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing." This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique.

Jan 1, 1929

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) No. 544.-Mining engineer, 39 years of age, graduate E. M. with extensive experience in the United States, Canada and Spanish-speaking countries. Good organizer, energetic and resourceful. Experience covers mining and milling of gold, silver, lead, copper, zinc and tungsten. At present a Captain of Engineers, U. S. A., expecting to be released shortly. Open for engagement as manager, superintendent or examining engineer. Correspondence and personal interview solicited. No. 545.-Engineer and geologist, member, age 29 years, technical graduate and married. Six years' practical experience as surveyor, chief engineer and in exploration work in West, Southwest and Mexico. Speaks French and Spanish. Desires position with exploration company or as engineer and superintendent of small mine. Will be released from commission in United States Navy about February 1. No. 546.-For staff position-or manager. Member, married, graduate mining and metallurgical engineer, 18 years' experience in underground and metallurgical work on gold, silver, copper, lead and zinc ores. Details, references, and qualifications will be sent if requested, or may be seen at Institute office. Available immediately in United States or Canada. Would go reasonable distance for an interview if desired. No. 547.-Member, experienced in mine operating, engineering, general contracting and constructing. Technical graduate, mining engineer, married, age 38 years. Many years' practical experience while advancing through different positions to manager. Best of references and rating. Desires change. Position with future. Can obtain results. Salary commensurate with position. Available on short notice. No. 548.-Mining engineer, member, technical graduate, age 31, on military service since August, 1914, available after January 31. Best of references.

Jan 3, 1919

By C. F. Wang

Page I. Introduction............:.............. 395 Manchuria in General ....................... 395 Pen-hsi-hu............................ 397 Pen-hsi-hu Coal & Iron Co., Ltd................... 399 I1. organization........................... 400 III. Coal Deposit........................... 402 Location..............................402 Geology............................. 403 Coal Mining...........'.................. 404 Mining Methods........................407 Mining Cost.........................408 IV. Coal Washing Plant.......................408 V. Coking Plant..........................410 VI. Iron Deposit...........................413 Magnetite Belt.......................... 413 Origin of Deposit......................... 414 Iron Mining........................... 415 VII. Concentration Plant........................ 417 VIII. Briquetting Plant.......................... 418 IX. Blast-furnace Smelting...................... 418 iNTKODtrCTION Manchuria in General Manchuria. called the "Three Eastern Provinces" in Chinese. forms the northeastern corner of China and is bordered by Siberia on the north and northeast. and by Korea on the east. It is a land famous in Chinese annals as the place of origin of the Ching dynasty. and in more recent times it has bcen an arena for diplomatic maneuvering and commercial competition between the Russians. advancing from the north. and the Japanese from the southeast. It derives its name of "three eastern provinces" from the fact that it is divided into three provinces; Hei-

Jan 1, 1918

By Russell A. Carter

Seven years of rising silver prices have effectively revived an historic Idaho mining district and given it a new lease on life. Initial production earlier last year from the DeLamar open-pit silver mine in southwestern Idaho ushered in a new era of mineral production in a region that has weathered boom-and-bust cycles reaching back the better part of a century.

Jan 1, 1978

By Leonard Obert

The structural stability of any mine or under- ground opening in rock is dependent on the stress field, that is, the state of stress in rock before mining, the stress distribution in the rock created by the opening, and the in situ strength of the rock. In the past mine design problems have been considered by assuming that the stress field is due only to the weight of the overlying rock, the stress around the opening can be calculated from elastic theory using laboratory-determined elastic constants, and the in situ strength of the rock can be determined from laboratory tests on small specimens. Solutions to hypothetical problems using this procedure are given in a report by Obert, Duvall, and Merrill.' Because of the uncertainties of these assumptions, this method can give only a rough approximation to the solution of actual structural problems. Obviously, this approach to determining the stability of underground openings would be greatly improved if the rock stress could be measured in situ, and it is undoubtedly for this reason that in recent years many investigators have spent considerable effort on the development of procedures for measuring rock stress. In this report a method is described for determining in situ the absolute stress in rock. The method requires the measurement of the deformation of a borehole before and after the rock is stress-relieved. The magnitude and direction of the applied stresses are calculated from the borehole deformation and modulus of elasticity of the rock. Also, the results of absolute stress determination made in the walls and pillars of underground openings in five rock types are presented. From these results a number of conclusions are drawn regarding the accuracy and limitations of this method and the problem of stress measurements in general.

Jan 8, 1962

By Bradley Stoughton

As a part of the systematic study of the alloys of iron under the auspices of the Engineering Foundation, and preliminary to the commencement of comprehensive work on this larger subject, the authors have undertaken an investigation of the available literature dealing: with the alloys of iron and silicon. The purpose is to collect all the data in English and foreign languages and present them in two mono-graphs, one of a more scientific and the second of a more industrially useful nature. Of course, a great deal of information upon the constitution of the iron-silicon alloys was found specificially upon the changes of phase in the equilibrium diagram and the different phases present, such as solid solution, chemical compounds (iron silicides), etc. While no extended research was contemplated in the particular study undertaken, nevertheless the data collected proved to be so contradictory in many respects that a simple study of some of the outstanding problems involved in the constitution and equilibrium diagram was undertaken Because research was not a primary object of the work, and also because of the extreme industrial importance of the silicon alloys between 0.80 and 14 per cent. silicon, and finally because of the unsatisfactory state of knowledge existing as to these alloys, the experimental investigation was limited entirely to alloys with less than 10 per cent. silicon.

Jan 1, 1930

By J. Wright, R. J. Tyler

Changes in the pore structure of hematite pellets during reduction to iron were investigated under a variety of experimental conditions. Pore structures were determined by a mercury penetration technique. The reduction temperature was found to be the major influence on structure, the pore system being bimodal below 7.50°C and unimodal above 900°C. Pore sizes ranging front 0.04 to 20 m were observed in complete metabolized pellets produced over the temperature range 650 - 1050°C. Gas composition and reduction rates also influenced the pore structure of the metabolized pellets, although to a lesser extent than the reduction temperature. An apparent activation energy of 24 kcal/mole was derived for the pore formation process.

Jan 1, 1979