Search Documents

By W. H. Emmons

MANY mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the [ ] steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement.

Jan 1, 1943

By Erwin L. Zodrow

A geological model of the modes of formation of magnetite and its distribution in the Smallwood iron-ore mine, Labrador, Newfoundland, is given, based on observation and geological mapping. This is called the conceptual model. If mathematical expressions plus probabilistic uncertainty are used to represent the conceptual model, then this is termed a mathematical model. The purpose of this paper is to test if there exists a correspondence between the conceptual model and two related mathematical models (called factor analysis). Details of the statistical technique are given. The results of factor analyses in relation to the magnetite formations in the Smallwood mine are discussed. Several practical mine applications are presented. The difficulty of maintaining quality control over ore mined from any deposit naturally depends on geological conditions; these are usually imperfectly known to concerned mining geologists. One geological condition that would greatly facilitate ore predictions is if a relationship between the observed ore particle distribution* and its mode of origin could be demonstrated. Such a casual interrelationship is normally sought through the application of well-defined geochemical principles of primary mineralization in given geological environments. However, the application of conventional tools of geological research, including geochemistry, to areas that have undergone repeated periods of geological deformation and metamorphism subsequent to primary mineralization becomes rather difficult. More important, the interpretation of such research results are nearly impossible on an objective basis. Mineral assemblages may have been reworked and changed due to tectonic influences to the extent that the present-day observable mineralogy and ore-particle distribution can effectively obscure the mode of origin of the ore. Quantitative measurements, based on petrological investigation of mineral assemblages, reflect the sum-total of all geological influences. Which of several influences had the most effect on existing ore particle distribution is difficult to assess, for these influences can neither be measured directly nor quantified by petro-logical logical or geochemical means. The present study is concerned with the magnetite distribution and its modes of origin within the Small- wood mine,' located in the southern extension of the Labrador geosyncline; see Fig. 1. This geosyncline is thought to have undergone at least two periods of geo-tonic tectonic deformation, separated in time, since the fer-rugenous rugenous sediments were deposited." Detailed geological observations and mappings (1 in. to 40 ft) have highlighted subtle, distinctive features of the magnetite distribution in the Smallwood mine: (1) The magnetite is generally concentrated in bands or layers within this ore body; these bands alternate with specularite-rich bands and quartz bands. The banded or layered nature is common in Precambrian iron-ore deposits, and this has been interpreted as a result of changes in depositional environments. (2) The grain size of the magnetite varies; near the contacts between the iron and quartz-carbonate formations, the magnetite occurs as well-crystallized octa-hedra. In areas of intense folding, magnetite is extremely fine grained and concentrated in bands and occurs in association with earthy manganese minerals. (3) Magnetite tends to be more highly concentrated near the geological contacts of the iron and quartz-carbonate formation in the northeast part of this mine, Figs. 2, 3, and 4. (4) Magnetite is also fine grained and tends to higher concentration near and parallel to fold axes; however, in this case, the ore is much softer than given in item 2. (5) Magnetite mineralization decreases along strike and away from the areas of intense folding, i.e., towards the approximate center of the mine, Fig. 3. How can these variations of magnetite be explained on a geological basis? We can postulate a conceptual model that the distribution of magnetite appears to be related to three basic geological influences: (1) geo-tectonics, i.e., concentrations of magnetite near geological contacts of the iron and quartz-carbonate formations, the fine-grained nature of magnetite and its higher concentrations near fold axes, and decrease of magnetite towards the approximate center of the mine; (2) secondary alterations, i.e., variation of grain size of magnetite near the iron and quartz-carbonate contacts, and in areas of intense folding where magnetite occurs together with earthy manganese minerals: (3) original

Jan 1, 1971

By R. J. Brown

Design of a submarine pipeline system is governed by many factors, one of which is the effect of transverse horizontal currents on the pipeline structure itself Although this feature alone can be of utmost importance to the life span and stability of the underwater pipeline, it is usually the least recognized, with these hydro-dynamic forces being either completely overlooked or grossly underestimated. In an attempt to supply the methods and means for stabilization of sub-marine pipelines, much capital has been spent by pipeline companies. Design criteria incorporated by these organizations extend over a broad spectrum of engineering with bases varying from pure theory to cut and dry methods. A history of numerous failures has substantiated the postulate that many of these submarine pipelines have been underdesigned from the stability standpoint. By the same token, equally as many have been excessively overdesigned with resultant excess expenditures. An attempt has been made in this paper to establish the magnitudes of these hydrodynamic forces by measuring the lateral current-induced differential pressure distribution around the periphery of the submarine pipeline. INTRODUCTION The expenditure of money for research by corporations obviously requires beneficial results to justify the investment. One of the functions of the engineer is first to make the problem known and then to provide a means of solution at the least possible cost. The initial procedure is to investigate all pertinent published technical articles on the subject to determine if this problem has been previously solved. If resolution of this problem is not obtainable, the next course of action is to evaluate through experiments these forces and their magnitudes. On the specific subject of drag and lift, the accumulation of data is provided from three separate and distinct sources: from experience, from theoreticians and through experimental observations. The experience source has proved costly with money wasted either because of underdesign and failure or excessive expenditures for overdesign, and has not been sufficient to form a definite conclusion on these hydrodynamic forces. The pure theoretician is often not completely cognizant of the situation and his works bear little adaptation to the real problem. The experimentalist has his own problems with regard to obtaining results from small-scaled models and successfully adapting them to the larger prototypes. Each method has its own advocates who diligently adhere to their own separate routes as being the only means of resolving this problem. However, a review of the various methods of analysis leads one to the conclusion that if the advantages of all three are combined, a reasonable solution to this problem can be reached. Briefly then, the problem is to obtain the magnitudes of the forces on the submarine pipeline subjected to a lateral current by investigations of previous design considerations, by a study of existing theoretica1 data and by appropriate experimentation. This paper deals mainly with obtaining experimental data and the interweaving of theoretical and experience factors for resolution of these forces. APPARATUS AND PROCEDURE These tests were performed in 1961 at Collins Construction Co.'s main office near Port Lavaca, Tex. Test equipment consisted of a steel tank 3 ft high by 4 ft wide by 40 ft long, with several pumps circulating the water through the tank via suction lines from the downstream portion of the tank and discharging from the pumps directly into the upstream end of the tank. For reduction of turbulence, a wire section was constmcted in the upstream portion and straightening vanes in the form of pipes, screens, etc., were used to reduce the vortex and eddy action in the tank (Fig. 1). A venturi was built at the test specimen for obtaining velocity sufficient to simulate actual conditions. This full-scale test was initiated to eliminate the error introduced in modeling and obtain a truer picture of forces actually encountered. Six- and 10-in. specimens were prepared by

Jan 1, 1967

By Walter L. Crow

MUCH has been published on highly technical phases of grinding. Very little has been written on how a mill man can improve his operations by determining the optimum size assortment of grinding balls that should be added as a makeup charge. This ball rationing is not to be confused with the ball ration used as an initial charge when the mill is started up. Ball rationing is considered for one or more of the following purposes: 1) to increase throughput of the mill, 2) to reduce the power required per ton of ore ground to the desired size, 3) to reduce steel consumption per ton of ore ground, 4) to improve product size, and 5) to lower retention time of ore in the mill.

Jan 7, 1957

By C. G. Dunn

According to a recently suggested effect of silicon on the re recrystallization textures of high-purity Fe-Si alloys with (111)[112] type rolling textures, the recrystallization texture for a rolled (110)[001] oriented iron crystal probably should be entirely different from that of a (110)[001] oriented 3 pct Si-Fe crystal. Comparative studies of iron and 3 pct Si-Fe crystals, however, show that both have (110)[Ool] recrystallization textures when the rolling textures are the (111)[112] type after reductions in thickness of about 70 pct. Qualitatively the results from the iron crystal are like those of polycrystalline high-purity 3 pct Si-Fe and not like polycrys-talline high-purity iron. The large effect previously noted probably involves unknown impurities or processing variables rather than silicon itself. Some problems on experimental and analytical procedure for a spherical X-ray specimen, which was machined from a laminated composite of sheet specimens, are treated in the Appendix. A possible strong effect of silicon on the textures produced in cold-rolled high-purity Fe-Si (HPFe-Si) alloys during primary recrystallization and normal grain growth was suggested in a recent paper.' All the textures were far from the random-orientation type, but that of iron, or of Fe-Si alloys of low silicon composition, was entirely different from the texture of 3 pct Si-Fe. The same effect was noted for the textures obtained prior to normal grain growth, i.e., for primary recrystallization.2 It is the main purpose of the present paper to provide some clarification of this silicon effect. All the HPFe-Si alloys from zero to 3 pct Si, which were rolled by two or more stages separated by anneals, developed (111)[112] type rolling textures.2 Thus, there was no effect of silicon on the rolling textures. Earlier, Gensamer and Mehl3 also found no effect of silicon on the rolling textures of Fe-Si alloys; they obtained the Kurdjum.ow and Sachs (K-S) rolling texture for iron,4 which is characterized as the three ideal components: (100)[011], (112)[li0], and (111)[112]. There is a difference between the HPFe-Si multiple-stage rolling texture and the K-S single-stage rolling texture, but this is a variable processing effect. Of interest here is the fact that the recrystallization textures from (111) [llZ] type rolling textures were different depending on the amount of silicon in the alloy. There was a relatively strong (110) [001] component in the recrystallization texture of HP 3 pct Si-Fe5,8,2 but no such component in HP 0.6 pct Si-Fe, for example; the recrystallization texture for the latter was two (111) [110] type components and a (111) fiber component 1,2 Several publications have shown that a strong (110) [001] recrystallization texture is derivable from a (111) [112] type rolling texture for 3 pct Si-Fe crystals reduced in thickness by about 70 pct.7-10 Furthermore it appears that the strongest of these (110) [001] recrystallization textures occurred when the orientation of the crystal prior to rolling was (110) [001].7 Barrett and evensoon11 found that the rolling texture of a (110)[001] oriented iron crystal was (111) [llj]. Accordingly, it seemed desirable to determine whether a (110) [001] oriented iron crystal, upon rolling and annealing, would behave like the 3 pct Si-Fe crystal (or the polycrystalline HP 3 pct Si-Fe) and thus produce a (110) [001] recrystallization texture contrary to the suggested silicon effect, or would behave like the polycry stalline HP iron or HP 0.6 pct Si-Fe and thus produce (lll) [110] type components in agreement with a silicon effect. Briefly, the idea here involves the use of more precisely defined textures to obtain if possible better control of important variables that affect the recrystallization process. PROCEDURE A (110) oriented crystal of Ferrovac "E" iron (99.9 pct pure) was prepared in sheet form 0.080 in. thick with the [001] direction parallel to the long dimension of the specimen.'' This crystal was etched to 0.073 in. thickness (to remove some small included grains) and then was cold rolled in a 6-in.-diam mill to a final thickness of 0.022 in. The rolling was unidirectional except for an inadvertent reversal at 0.061 in. thickness. At this thickness, and also at 0.040 in., the rolling was interrupted for transmission Laue photographs. Molybdenum Ka-radiation filtered with zirconium was used in a transmission method1' to obtain the cold-rolled (110) pole figure. The sample was a 0.002-in.-thick section taken from the central region of the 0.022-in.-thick cold-rolled crystal. For the primary recrystallization study, cold-rolled samples were etched from 0.022 to 0.021 in. thick and annealed in hydrogen at 850°C. Primary recrystallization to a fine-grained structure, Fig. 1, was obtained in a 5-min anneal. Eleven sheets after

Jan 1, 1963

By Augustus Locke

The paper has two parts: the field argument and the microscopic argument. The field argument indicates that either the deep chalcocite has replacea sulfide of extraordinarily easy replaceability or it is hypogene. The microscopic argumentindicates that this sulfide, if it existed, must have been hypogene bornite; that this bornite must so excel known bornite in replaceability as to constitute a new variety; that the existence of this new variety is wholly unsupported by evidence; and that the deep Butte chalcocite is therefore hypogene. IN 1900, when the public first heard of "secondary enrichment" the Butte chalcocite seemed clearly supergene. Mining, through successive regions of leached capping, bonanza sulfide, and sulfide less rich, had paused at lean bottom levels which, though chalcocite-bearing, suggested the waning of copper. The deepest chalcocite, at 1500 ft., was yet too shallow to disturb the supergene hypothesis. But, with deeper mining, lean levels yielded to fat ones. Here and there they showed, within the same vein, an inverted distribution, chalcopyrite above and chalcocite below. To the miners' astonishment, they carried chalcocite, unaffected by cross faults, on an independent course to the depth of 2500 ft. The pattern of ore distribution, hitherto revealed only in fragments, was now appearing in perspective, and, in the depth of the chalcocite, was beginning to make Butte differ from all districts where the chalcocite is indubitably supergene. The idea of hypogene origin at length came into favor; by 1913, when Sales1 advocated this origin, the argument had become a powerful one. This argument rested on field evidence; but, already, there was beginning to emerge microscopic evidence not included in this arugment. Especially pertinent was the proof that (1) The deep chalcocite lies in-mixed with bornite, often microscopic; (2) the deep chalcocite often replaces bornite; and (3) replacement of bornite by chalcocite is accom-

Jan 3, 1924

By A. M. Gaudin

UNTIL recently little attention has been paid to the effect of particle size on flotation. This has been especially true of material finer than 200 mesh.1 Particles of different sizes must behave differently in a flotation circuit; increased information along this line would be of practical use as well as of theoretical interest. The object of this study has been to determine what effect particle size has on floatability. The problem has been approached in two ways. One method consisted in a study of samples of the final products of several mills. These samples were sized and each size-product was analyzed for its important constituents. Bakelite briquettes2 of some of the products were made and studied under the microscope. This investigation is being continued, with particular reference to quantitative microscopic analysis of intermediate products of flotation plants. M In the other method of study, mixtures of pure minerals were ground to different degrees of fineness and floated. The products were then sized and analyzed. A study of the behavior of mixtures of pure sized minerals would have been illuminating, but after trial it was considered impractical on account of the tediousness of the large amount of elutriation required and the fact that the mineral particles would oxidize while being sized, preparatory to flotation. Broadly speaking, the following conclusions have been reached: 1. Results obtained by the two methods of study are in agreement. 2. The usual notion about the relative ease of flotation of very fine particles does not agree with the facts: 3. There is a time sequence of flotation with regard to particle size, the medium coarse particles floating first. 4. No successful method of floating extremely fine pulps has been found. 5. Recovery is optimum in a certain well-defined size range. 6. Selection is optimum in another well-defined size range.

Jan 1, 1931

By Carl Davis

A description is given of grinding practice on the Rand and of experiments made to improve that practice. The paper includes a description of the experimental plants and methods and the results obtained. THE first tube-mill on the Rand was put into operation in May, 1904, at the Glen Deep Mine. From that time onwards, tube-mills were added to various plants, although little was known regarding the capacity of a given tube-mill when working on banket ore. Within a few years, however, the so-called standard size (length of shell 22 ft. 0 in. diameter 5 ft. 6 in.) was generally used until the last year or two. Practically the only exceptions were about 30 tube-mills having a length of 16 ft. and a diameter of 6 ft., and a few open-end mills of the roller-supported type. Most of the information obtained during the last 15 years has been obtained with mills of the standard dimensions. The adoption of the tube-mill as an accessory to the stamp mill was rapid; and where 3 tube-mills were working on the Rand at the end of 1904, 244 were in use seven years later.1 By 1910, good practice provided 1 tube-mill for 20 stamps of 2000-lb. falling weight. The horsepower of the motors driving the tube-mills had increased from. 80 to 100 and then to 125 at this date. Broadly speaking, current practice at that date aimed at a final product of which 60 per cent. was suitable for sand treatment and 40 per cent. for slime. The sand grading was +60 mesh, 6 per cent.; +90 mesh, 25 per cent.; -90 mesh, 69 per cent.; and the slime grading -200 mesh, 2 per cent.; -200 mesh, 98 per cent.

Jan 12, 1924

By H. S. Martin

THE Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the pres-ent time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been oper-ated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined eco-nomically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine sus-pended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the dis-tribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation's trolley system, to the drying plant at Prairie, one mile northwest of Mulberry.

Jan 1, 1933

By Damon H. McFadden

5.1-1. Geographic and Geologic Factors. Surface mines are located where the coal seam can be economically uncovered and where the product can be utilized competitively with other fuels. The planning and designing of a pit may follow various procedures. The sequence for consideration of the influential factors as considered here may not be complete for every pit, nor will it be necessary to be completely used in each design. It is suggested as a check and outline for the engineering approach. Controlling conditions for the layout should be listed and considered with the facilities and equipment for the exploitation. After these items, as listed below, have been discussed and the feasibility agreed upon, then the actual planning and design of the pit can be done. GEOGRAPHIC FEATURES. The location of the coal area sets the climatic stage. The rainfall, the temperature extremes, and the general weather conditions all affect the design of the pit. Overburden soil when wet may not be stackable and may be impossible to move by standard procedures. The coal seam itself may be so soft that it must not be traveled on when wet, as the losses may be the difference between a profitable venture and an unsuccessful one. Some equipment will work well on dry soil only, just as a dredge works only in the wet. The conditions must be checked and analyzed. Some equipment cannot handle frozen soil (wheel excavators), so temperature extremes must be noted. The extreme weather conditions may also govern the expected working days and therefore the ultimate production. The altitude (atmospheric pressure) may affect the equipment, and this should be checked. All of these conditions should be noted on the preliminary map of the area. GEOLOGIC FACTORS. The geologic and surface conditions of the coal field dictate the type of pit generally feasible. Rough terrain, rolling terrain,

Jan 1, 1968

By J. L. Rodda, M. L. Fuller

In connection with an investigation in this laboratory on the high-zinc side of the copper-zinc system, it was observed that well developed segregate structures of the Widmansttten type were formed when a secondary phase precipitated from the solid solution of copper in zinc. This paper presents an analysis of the crystallographic relationship between the segregate and the solid solution matrix. The data to be presented are an interesting addition to the literature on segregate structures in that the plane of segregation is one of the less densely populated planes. In agreement with the generalization of C. H. Mathewson and D. W. Smith' the plane of segregation in the matrix contains the direction of closest atomic packing of the lattice. Furthermore, the matrix and the segregate are both hexagonal close-packed, which has not been reported hitherto in the 1iternture.l The increasing commercial importance of zinc alloys containing copper makes this fundamental study of value to the metallography of zinc alloys. Zinoeich Copper-zinc Alloys Copper enters into solid solution with zinc to at least 1.8 per cent at 400" C., according to W. M. Peirce.3 The solubility is less at lower temperatures. Thus a solid solution of copper in zinc, saturated at an elevated temperature, will precipitate the excess copper in a separate phase at a lower temperature, conditions of concentration, time, and temperature being suitable. The nature of these two phases has been established by the X-ray method of crystal analysis. Westgren and Phmgmén4 and also Owen and Preston5 have shown that the solid solution eta (7) is of the substitu-tional type with copper atoms replacing zinc atoms on the hexagonal

Jan 1, 1933

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would not be very useful even if they were available; however, what few , approximate data there are, can be used in combination with data given in Chapters XVI and XVII to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. As discussed in the last portion of Chapter XIII chemical reactions in general involve the following factors: 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. A certain number of collisions occur per unit time among the reagent molecules, depending on their concentration and on temperature. 3. A certain percentage of these collisions result in reaction, these being the collisions between those molecules possessing at the moment energy levels above certain minimum values. The temperature factor enters mainly through (3), and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the molecules will have much higher energy content than the mean value.) Various reaction rates measured at around room temperatures have been found to be speeded from 1.6 to 4.0 times by an increase of only 15 to 20°F., simply because increasing temperature produces a rapidly increasing percentage of molecules with energy levels above the minimum needed to produce chemical reaction in a collision.

Jan 1, 1944

By B. B. Betty

H. L. Burghoff.*—Have the authors any information on the effect of grain size in these materials? There is a material difference in the grain sizes shown for the Monel and the Inconel. Is a wide range of grain size normally found for each material, and, if so, what is its effect upon creep strength? 11. L. Eiselstein.—The grain size for Monel shown in the micrograph is the usual size found in that product. The grain size of Inconel is about the same as that, too. However, we have run tests on Inconel at higher temperatures than those reported in this paper, and have found that the coarser grain size has a better creep resistance; and that the grain size that gives the best creep resistance at 1600°F. is about 0.005 in. in diameter. We have no test on Monel with varying grain size. J. J. KANTER.†-It has been known for a long time that Monel metal exhibits ductility anomalies at elevated temperatures. Even in short-time test, it can be demonstrated in the range of 900°F. that there is a distinct falling off of the ability of Mone1 metal to elongate, and in rupture tests this shortcoming is still further accentuated. Knowledge of this rupture anomaly of Monel metal may be one of the reasons for which designer's approach certain high-temperature applications with reservations. The authors of this paper have merely demonstrated that for 900°F. the alloy has an ability to elongate 1.7 per cent over a period of some 2700 hr. Before any conviction can be expected from designers that Monel metal is applicable to stress design in such range of temperature, I think it is desirable to demonstrate the capacity for the material to elongate over a longer period of time than has been done in this presentation.

Jan 1, 1945

By S. R. Zimmerley, John Gross

The deductions drawn in crushing and grinding operations have heretofore been based on a separation of the products into various sizes. A crushed product may be sized by sieving, by elutriation and by aid of the microscope. To estimate the surface of each size the relation of the surface to the estimated average diameter must be assumed. Such a relation, owing to the irregularity of the particles, may involve two assumptions: First, a factor to convert average diameter to surface for one particular size; and second, a variation in the factor as the diameter of the particle changes. Obviously a surface measurement in which such assumptions and estimates are involved is questionable. In the first paper of this series1 a method has been given by which an accurate measure of surface of quartz can be obtained from its dissolution rate. By the use of this method, surface measurements have been made on a series of sieve sizes of crushed quartz, the results of which are given and discussed in this paper. Prepaeation of the Quartz Sizes The quartz, consisting of large uniform pieces with a density of 2.65 and a purity of 99.5 per cent. SiO2, was crushed to pass 20 mesh and was then sieved. Tyler standard sieves were used, the sieving being done by hand according to the proposed standard method submitted by the senior author to the Milling Committee of the A. I. M. E. A wet split of the sample was made on a 270-mesh sieve. This was followed by dry sieving until less than 0.05 per cent. of the weight of the sample passed through the sieve in 1-min. sieving. The +28-mesh material was discarded because that size did not contain the difficult grains from the 20-mesh sieve.

Jan 1, 1930

By Samuel Wyer

Over 8,000,000 people in the United States depend on natural gas for their cooking, heating and lighting service. This service has been made possible only by the investment of large amounts of capital in transportation lines connecting the gas wells to the various communities, thus combining a hazardous mining operation with a public utility service. The effect that making these lines " common carriers" will have on the present and future service to these 8,000,000 or more people is of far reaching ethical and economic importance, and deserves careful consideration. As an introduction, it must be conceded that: 1. Natural gas, although a mineral and obtained by a mining operation-with more uncontrollable and uncertain features to cope with than exist in the mining of coal or other minerals-when served to the public becomes a public utility service. 2. The governmental power to regulate all public utilities in the interests of the public cannot be successfully disputed. 3. Mere suggestion of inconvenience to the utility is wholly irrelevant, as it cannot be considered or allowed to influence in making a defense against governmental regulation. Unfortunately it is not generally appreciated that: 1. Legislative enactments are not necessarily laws, and cannot abrogate economic laws or alter engineering facts. 2. There is a clear distinction between "common carrier" and "public utility," although the terms are frequently confused. ' "A common carrier is one who undertakes for hire to transport persons or goods, or both, from place to place for all persons indifferently, the term implying indifference as to whom shall be served, and an equal readiness to serve all who apply, in the order of their application." On the other hand, property becomes a "public utility" only "when for a particular purpose the public have a right to resort to the premises and make use of them."

Jan 5, 1914

By William R. Rumbold

When I was in South Africa during the latter part of 1904, there were three known tin-fields, which may be called the Cape Town, the Bushveld, and the Swaziland fields. The Cape Town Tin-Field. This district is situated near Kuils river, 20 miles west of Cape Town, and 5 miles from Kuils River station on the Cape Town & Stellenbosch railway. The deposits are in granite, intrusive in the Malmesbury beds, which are supposed to be of Silurian or Cambrian age. The granite, resisting denudation better than the surrounding shales, has formed low-lying hills, the highest of which, the Bottlelary Berg, is 1,510 ft. above sea-level. The rock consists of quartz, orthoclase feldspar, and biotite mica; tourmaline is also present. The feldspar occurs in large crystals. The rock is generally decomposed on the surface, and the decomposition sometimes extends as deep as 100 ft. This formation—granite intrusive in Silurian shales— extends for many miles to the northeast, but so far as I know the Kuils River deposits are the only ones now known to occur in it, though probably further prospecting will reveal other deposits. This particular discovery was accidental; alluvial tin being found in the course of boring for oil. The Kuils River Deposit. This deposit comprises both lode and alluvial tin. The lode strikes N-S., and dips about 30' E. into the hill. It is 5 ft. wide, and composed of dense white quartz, in which pinkish-gray cassiterite is distributed in large crystals. The vein also contains considerable quantities of wolframite. Fig. 1 is a rough plan of the relative positions of the lode and the alluvial deposit, the latter, as shown, following the course of a stream, while the lode crops out on the hillside ,

Jan 1, 1909

By Theodore R. Butkovich, Jesse L. Yow

Geological storage of spent-fuel assemblies from an operating nuclear reactor has been underway since the Spring of 1980 at the U.S. Department of Energy's Nevada Test Site. The primary objective of this generic test is to evaluate granite as a medium for deep geological storage of high level reactor waste and to provide data on thermal and thermomechanical behavior of granite from imposed heat loads.(l) The underground installation in the Climax stock granite was sited at about 420 m below the surface and 145 m above the existing water table. As shown in Figure 1, three parallel drifts were excavated spaced on approximately 10 m centers. Seventeen storage holes were drilled at the central drift on 3 m centers in which eleven spent fuel canisters and six thermally identical electrical simulators were emplaced. Electrical resistance heaters were emplaced in vertical holes in the floor of the side drifts on 6 m centers. The thermal output of these heaters is being periodically adjusted to simulate the thermal response of a large storage array. Rock and ventilation air temperatures are being measured continuously in the drifts and throughout the rock surrounding the excavations. Measurements of drift deformation have been made routinely since the emplacement of the spent fuel. Both vertical and horizontal measurements are being taken at five locations along the heater drifts and at six locations along the central canister drift (Fig. 1). Two types of instrumentaton are being used: convergence wire extensometers which are monitored automatically, and a manually operated tape extensometer with which measurements are taken periodically. The tape extensometer measurements were initiated about 6 weeks following fuel emplacement. The lack of a temperature correcting capability for the convergence wire extensometers make that data unavailable for analysis at this time.

Jan 1, 1982

By F. L. Grammer

The analyses given in Table I. were made several years ago at my request at a plant using Lake ores. They are of two furnaces, one making basic, the other Bessemer pig— they gave 6 casts each in 24 hr., also two flushes of cinder between each cast. They are offered simply for the sake of reference as, so far as I know, it is unusual to find so frequent full analyses made and none are on record. The variations in manganese-content in the first and second flushes on the basic furnace are interesting, if no more than a freak—the first flush being invariably higher in manganese. The iron-content of the two slags from an average of 12 flushes shows: Basic. Bessemer. Per Cent. Per Cent. Total iron...................................... 2.85 1.70 Combined iron................................ 0.72 0.52 Free iron....................................... 2.13 1.18 The greater iron-loss in the basic slag, while known, has never heretofore been so clearly set forth. This may modify the arrangement for handling slag; heretofore usually determined by proximity of the dumping-heap. If a nearby heap is used on contiguous territory, in the past, tilting molten-slag pots were used. If the Pittsburg flood-records for 30 years are a fair criterion the government regulations were inadequate, and molten slag was dumped in such a manner as to throttle the Monongahela at the time of the spring thaws. At Pittsburg the slag, where it is carried to a distance, is frequently granulated in pits and then removed in cars to which it is conveyed by clam-shell buckets. This practice is also quite customary where the slag is intended for the manufacture of slag cement. The production of 500 tons of cast-iron daily means about 300 tons of- slag and at 2.113 per cent. equals 6.4 tons

Jan 1, 1914

By C. P. Karr

FOR several years, the Bureau of Standards has been working in cooperation with an Advisory Committee on non-ferrous metals on various phases of the production and testing of zinc bronzes. The work has dealt, especially with the type of metal known as "Admiralty bronze" in England and as "Government bronze" in this country and consisting of 88 copper, 10 tin, and 2 zinc. Several reports have been made on this subject and these should be considered in connection with this paper.1 FIRST SERIES OF FIVE FOUNDRY TESTS A very brief summary of the first series of five foundry tests has been made,2 but for the sake of clearness the results are given here in different form. The five foundries cooperating in this investigation were: Ohio Brass Co., Mansfield, Ohio; Titanium Alloy Mfg. Co., Niagara Falls, N. Y.; Packard Motor Car Co., Syracuse, N. Y.; National Cash Register Co., Dayton, Ohio; Bureau of Standards, Washington, D. C. The object of the work was to determine whether uniform results could be obtained with this alloy in different foundries working under definite instructions. One of the participating foundries prepared, from virgin metal, a stock of ingots of the composition 88 copper, 10 tin, 2 zinc, and at the same time poured nine test bars from this melt of virgin metal. The results of the physical tests of these bars are shown in Table 1. Examination of this table shows that the highest and most nearly uniform results were obtained when the virgin metal was cast flat in chill molds and the lowest and most variable results were encountered when it was cast vertical in green-sand molds. In this, as in all other tables, the mean

Jan 9, 1919

By B. H. Bergstrom, A. P. Cohen, D. W. Fuerstenau

B.H. Bergstrorn (Research Div., Allis-Chalmers Mfg. Co., Milwaukee, Wis.) — Fuerstenau and Cohen have concluded from our study of single particle crushing, which had suggested that the size moduli of the crushed specimens were determined by the specific energy expended independent of feed size, that the same independence with respect to feed size exists for the specific energy-product size relationship for rod mills. They present data supporting this conclusion. Our single particle crushing experiments were on single spheres of soda-lime (type of glass was not given in our study) glass for which the feed size can truly be neglected. However, the feed size cannot be neglected in any case where the effective size modulus of the feed is not too much coarser than the size modulus of the product. This can be illustrated in the second experi- ment of Fuerstenau and Cohen where the feed is considered to be the original -6 +%mesh material. However, one can also consider the product from the 7.5-min grind to be the feed for the 10, 15, 20, 25-min grinds, and the 10-min product to be the feed for the 15, 20, 25-min grinds, etc. If the specific energy-product size moduli curves are drawn for these other feeds, as shown on Fig. 3, the new curves (and some curvature is apparent) are much steeper than the -6 +%mesh feed line. The slopes of these new curves are about -1.5, —1.8 and -3.0. This observation is in accord with the observation by Bond, who states that the net specific energy input to a grinding mill is equal to the specific energy represented by the product less the specific energy represented by the feed. Bond presents, on a diagram similar to Fig. 3, a series of curves which illustrate the effect of

Jan 1, 1963