Search Documents

Coal - Surface Mining Coal Preparation Coal Utilization Research and Development Health and Safety

Jan 3, 1976

By WM. E. Mlligan

IN the last year, much information had become available as to the extent that zinc participated in the war effort. The importance of foreign zinc in this program had been indicated by Bateman (M&M April 1945) as of the order of 400,000 tons annually in zinc or contained zinc. Pehrson (M&M April 1945) reviewed the domestic ore-reserve situation with respect to most minerals and metals and showed the extent to which commercial zinc ores had become depleted in this country. This picture was further darkened by O.P.A. figures appearing in E.&M.J. July 1945 in which figures for total production during the three previous years were broken down into percentages produced under ceiling and various quota price categories. True, factors other than depleted ore reserves contributed to this picture. Among the more important of these, were shortage and high cost of labor, both skilled and unskilled, and the general difficulty and cost of maintaining adequate equipment and supplies. The cost of production in the Tri-State district was most affected.

Jan 1, 1946

By C. J. Beevers

Tlze influence of zirconium hydride precipitate mprphology on the fructure of Zr-H alloys tested at strain rates of 10- sec at 20° and - 196°C and at strain rates of -500 sec.-1 at 20°C has been inves-tigated. The critical stage in the embrittlement of these alloys was the fracture of the zirconium hyhide precipitates to form large interval cracks at a stress of 25,000 10 137,000 psi. In specimens con-temping up to 100 ppm H the preciptates existed as isolafed platelets in the zirconium matrix and their fracture as enhanced by low temperature (—196°C) and high strain rate (-500 set-f) loading. These resl~lts lead to the conclusion that the rate of strain hardening of the zirconium metal controls the frac-tzrm of the hydride platelets. Increased hydrogen contents of 500 to 2000 ppm resulted in an increase in the 1)volume fraction and size of precipitates and crlso led to crack propogation in the hydride at both 20 and —196C at the low strain rates (10'* sec-'). Quenching led to refinerment of hydride precipitate size and reduced the degree of embrittlement at — 196°C; this effect is attributed to the absence of fracture of the fine precipitates. The formation of zirconium hydride precipitates has been shown to be the cause of hydrogen embrittlement of zirconium.' Several investigators'-" have studied the problem in broad outline, demonstrating that impact-loading conditions, testing temperatures below room temperature, and increasing hydrogen content produce increased brittleness. For example, Muehlenkamp and schwope2 showed that the transition temperature for notched impact tests was raised from 150" to 350°C on increasing the hydrogen content from 45 to 490 ppm. The degree of embrittlement is also controlled by the morphology of the zirconium hydride precipitates. The solubility of hydrogen in zirconium decreases from 600 ppm at 550°C to 10 ppm at 20"C,~ so that the form of the zirconium hydride precipitates (ZrH2) can be modified by varying the cooling rate through the Zr-aZr + ZrH2 phase boundary.= Forscher showed that quenching a specimen containing 35 ppm H from above 315°C resulted in a reduction in area of 70 pct at -196"C, whereas slowly cooling from above 315°C resulted in a ductility of half this value. The role of the hydride precipitate in the fracture process has been examined by Young and schwartz6 and more recently by westlake.' From metallo-graphic observations on slowly cooled Zr-H alloys they have suggested that cracks are nucleated in the hydride precipitates by the interactions of twins in the zirconium metal with the hydride. The experiments reported in this paper show that crack propagation in the zirconium hydride precipitates is the critical stage in the embrittlement of Zr-H alloys. The factors influencing fracture of the hydride precipitates and crack propagation in the zirconium metal will be related to the problem of embrittlement. EXPERIMENTAL TECHNIQUES The zirconium used in these experiments was produced from an ingot of vacuum arc-melted iodide zirconium forged down to 1 in. diameter at 800' to 850°C. The 1-in.-diameter bar was surface-machined and cold-swaged to 0.375 in. diameter. After a vacuum anneal at 800°C for 1 hr the hardness was 60 to 70 Vdh. The total impurity content was approxi-

Jan 1, 1965

By Jay A. Carpenter

This paper deals with only one step in the treatment of ore at the West End mill; not because the other steps are repetitions of practice in other mills, but because in this particular step there is in use the Trent agitator: This device, although it has apparently failed in many mills, is here giving excellent service and has proved to be well adapted for making a thorough replacement of pregnant solution with a minimum amount of barren solution. The strong and weak points of this agitator, its present simple construction, and its use as a thickener for agitator or battery pulp are features of interest; but perhaps the point of greatest interest to the metallurgist in this day of continuous decantation is its use in a series of tanks for slime treatment by the replacement method. The agitating department of the West End mill consists of six redwood tanks, 24 ft. in diameter, 18 ft. high, each equipped with a Trent agitator, a centrifugal pump, and a motor. The pulp is transferred by a pump from the top of a flat-bottomed tank to a set of arms and nozzles in the bottom of the tank, at just sufficient pressure to cause the arms to revolve. The streams from the many nozzles keep the bottom of the tank clean, and these streams, coupled with the effect of the revolving mechanism and the ascending current, keep the pulp in constant motion and of constant gravity. These agitating tanks hold 90 tons of dry slime and 202 tons of solution with a 1.24 pulp, our ore having a specific gravity of 2.7. This capacity is about 10 per cent. in excess of the standard 15 by 45 ft. Pachuca tank. The tanks are connected in one series for continuous agitation, the pulp for each agitator being drawn by its pump through a branch suction from near the top of the preceding tank and delivered to the bottom of the tank by the agitator arms along with the regular pulp of that agitator. This method works automatically, since the flow through the branch suction varies directly with the difference in head of the two tanks. The chance for new pulp to pass out quickly is, therefore, much less than in many other systems of continuous agitation, since the new

Jan 1, 1916

By Jay Carpenter

THIS paper deals with only one step in the treatment of ore at the West End mill; not because the other steps are repetitions of practice in other mills, but because in this particular step there is in use the Trent agitator. This device, although it has apparently failed in many mills, is here giving excellent service and has proved to be well adapted for making a thorough replacement of pregnant solution with a minimum amount of barren solution. The strong and weak points of this agitator, its present simple construction, and its use as a thickener for agitator or battery pulp are features of interest; but perhaps the point of greatest interest to the metallurgist in this day of continuous decantation is its use in a series of tanks for slime treatment by the replacement method. The agitating department of the West End mill consists of six redwood tanks, 24 ft. in diameter, 18 ft. high, each equipped with aTrent agitator, a centrifugal pump, and a motor. The pulp is transferred by a pump from the top of a flat-bottomed tank to a set of arms and nozzles in the bottom of the tank, at just sufficient pressure to cause the arms to revolve. The streams from the many nozzles keep the bottom of the tank clean, and these streams, coupled with the effect of the revolving mechanism and the ascending current, keep the pulp in constant motion and of constant gravity. .These agitating tanks hold 90 tons of dry slime and 202 tons of solution with a 1.24 pulp, our ore having a specific gravity of 2.7. This capacity is about 10 per cent. in excess of the standard 15 by 45 ft. Pachuca tank. The tanks are connected in one series for continuous agitation, the pulp for each agitator being drawn by its pump through a branch suction from near the top of the preceding tank and. delivered to the bottom of the tank by the agitator arms along with the regular pulp of that agitator. This method works automatically, since the flow through the branch suction varies directly with the difference in head of the two tanks. The chance for new pulp to pass out quickly is, therefore, much less than in many other systems of continuous agitation, since the new

Jan 8, 1915

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix.

Jan 11, 1951

By H. E. Kramm

(New York Meeting, February, 1919.) DURING the summer of 1911, I had the opportunity to study in detail the geological conditions of what is known in northern California as " Harrison gulch," in Shasta county. Though the district, as a whole, that is, the western part of Shasta and the eastern part of Trinity county, has contributed during the last 15 years a considerable share of the gold-production credited to Shasta county, very little is known of its geology, perhaps because the country is covered with a dense growth of brush which makes exploration and prospecting extremely difficult. Topographically the district presents a succession of ridges trending approximately N-S.; and alternating with deep narrow canyons. The drainage is partly into . the Sacramento, partly into the Trinity river. Climatic conditions in summer time are almost ideal. It is true, the thermometer may climb to 115°, but the air is dry and the heat is bearable, especially as the nights are always cool. It seldom rains during the summer months, and creeks and springs dry out towards the end of the summer. The winter is severe, lasting from November to April, and usually a thick layer of snow covers the mountains. By reason of the character of its gold-deposits, the region is known to miners as "the pocket country." It contains a series ?of eruptive rocks intruded into slates, cherts, limestones, and conglomerates. Dikes, laccoliths, and batholiths are frequent. In a day's ride it is possible to find all the common igneous rocks from the very acid to the very basic. Serpentines are especially abundant.. The sedimentary rocks are, as rule, broken and shattered as well as folded, and show the effects of intense metamorphism. ? Pocket-hunters " speak of the contact of diabase and slate as the ? pocket-contact." Some rich gold-pockets, however, have also been found in the diabase.

Jul 1, 1912

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists It Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Howard-Canfleld Bldg. Santa Barbara, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction I-lath St. S. W. B'ham, Ala., Phone 56-5566 MILTON H. FIES Consulting Engineer Rooms 1201-2. Albama Power Co. Bldg. Birmingham, Alabama]

Jan 1, 1952

CHARLES E. GUILLAUME,* .Sèvres, France written discussion?).-Referring top. 2052, experiments made at the end of the year 1884showed a remarkable agreement between the indications of various verre dur thermometers of which all the corrections had been determined with the greatest possible precision. The maximum deviations not attributable to the comparisons themselves were then about 0.002 to 0.003 degree. Much later, greater differences began to show. They were caused by the fact that the glassmaker-had modified the composition by adding to it a small quantity of lead. Efforts are now being made in France to obtain a regular, supply of glass made according to the old formula. The determination of the boiling point of sulfur made by Chappuis,1 444.5°, accords very well with the value noted on p. 2054. The International Committee of Weights and Measures and the General Conference have already considered the future abandonment of the hydrogen scale in favor of the thermodynamic scale. The hydro-gen scale appears to be, in their estimation, a transitory one, happily so closely approaching the final scale that no correction should be necessary for all measurements of temperature made during the last 30 years.

Jan 12, 1919

By R. M. Brick

EDUCATIONAL benefits for veterans of World War II have largely removed one of the two former barriers to a college education for everyone, namely financial means and intellectual capacity. This latter limita¬tion has not kept privately endowed institutions from increasing 50 to 100 percent in size of student body, even after applying moderately rigid entrance standards. Growth of some land-grant universities, which cannot well exercise such restrictive judgements, has been even greater. After a weary board of admissions, subject to student, alumni, faculty, and even political pressures, has admitted double the former number of freshmen, the university's worries really begin: to find laboratory, classroom, and instructional facilities. If this were a one- or two-year problem, the answer would be simple: double up, hold night classes, particularly of laboratories, rent space, and have instructors work 24 class or contact hours a week instead of twelve (it takes usually two to three hours of outside work by the instructor for one hour in class). However, most engineering school faculty men are worn out now from four to five years of "accelerated" (frequently downward!) programs and they couldn't continue teaching in a way satisfactory to their own consciences on

Jan 1, 1947

By S. C. Lindsay, D. J. I. Evans

With each year that passes hydrometallurgical processes are being more widely used to recover base metals from ores and concentrates. Generally these processes involve liquid-solid separation of metal-bearing liquors from barren residues. This may be done by countercurrent decantation, thickening and filtration, or filtration or centrifuging only. Choice of method is governed by chemical and physical characteristics of the pulps; cost of labor, power, materials, and waste disposal; and even by the amount of capital available when building plans are under way. Since all these controlling factors change with time and location and with technological advances, the separation method must be re-evaluated when new plants or expansion programs are contemplated. At the Sherritt Gordon refinery in Fort Saskatchewan, Alberta, an ammonia pressure leaching process recovers nickel, copper, and cobalt from the nickel concentrate produced at Lynn Lake, Manitoba.' Pregnant liquors are separated from the barren leach residues in a thickener-filter liquid-solids circuit. The decision to use this type of separation was based on a summation of economic factors during the pilot plant and design stages. Although countercurrent decantation was not incorporated in the refinery flowsheet, the problems solved in thickening the leach residues and the experience gained in operating the commercial plant are pertinent to countercurrent decantation, particularly where it is applied to slow-settling leach slurries or slurries having a relatively high vapor pressure of a valuable, obnoxious, or poisonous vapor. The nickel sulfide concentrate is leached under pressure with air and ammonia to dissolve the nickel, copper, and cobalt and most of the sulfur, leaving a residue of iron and siliceous material to be discarded.2,3 During a subsequent distillation stage to recirculate part of the ammonia used for leaching, copper is recovered from the solution as a high-grade sulfide. After further purification to remove traces of copper and undesirable sulfur compounds, the nickel is precipitated by hydrogen under pressure at an elevated temperature. The cobalt, together with unreduced nickel, is precipitated as a mixed metal sulfide by hydrogen sulfide for eventual cobalt recovery. The end solution is then evaporated to produce a crystalline ammonium sulfate byproduct. As shown in Fig. 1, the nickel concentrate is leached in a continuous, two-stage, countercurrent circuit. In the first stage, or adjustment leach, the fresh concentrate is partially leached (60 pct) in the liquor produced in the second stage, or final leach. This system is necessary to produce a solution suitable for treatment in the copper sulfide precipitation step. Both stages are carried out at 170" to 180°F under a total pressure, with air, of 100 to 120 psig in large, horizontal, water-cooled autoclaves. The autoclaves are divided by overflow weirs into four compartments to give a certain amount of staging during leaching. In each compartment a relatively slow-speed (100 to 150 rpm) agitator maintains the nickel concentrate in suspension. Adjustment leaching, carried out in two autoclaves in parallel, is followed by a thickener-filter liquid-solids separation. Final leaching is done in two parallel trains of three autoclaves using aqueous ammonia to extract metal values from the adjustment leach residues. This too is followed by a thickener-filter circuit. Here the residues are repulped once with aqueous ammonia and twice with process water and refiltered after each repulping stage, to insure a maximum recovery of soluble metal, before being discarded to the tailings pond. The adjustment leach is followed by a seven-disk Dorr-Oliver American filter, with an agitator in the filter boot to keep the residues in suspension. Agitators have also been installed beneath the four ten-disk filters following the final leach thickener. Slurry Characteristics: A typical analysis of the Lynn Lake nickel concentrate, produced by differential flotation,' is given in Table I. The concentrate comprises 35 to 49 pct pentlandite, (Fe, Ni)S; 3 to 6 pct chalcopyrite, CuFeS,; 1 to 4 pct pyrite, FeS2; and 24 to 42 pct pyrrhotite, Fe1-2S (where x varies between 0 and 0.2) together with various siliceous minerals such as actinolite, hornblende, and talc. During leaching, the sulfur in the pentlandite, chalcopyrite, and part of the pyrrhotite is successively oxidized through the thiosulfate and poly-thionate radicals to sulfate and sulfamate." Simultaneously the nickel, copper, and cobalt are converted to soluble ammine complexes and the iron in the pentlandite, chalcopyrite, and part of the pyrrhotite is oxidized to a spongy hydrated iron oxide. The hydrated iron oxide is readily broken down by the agitation needed to sustain the concentrate in suspension and to maintain a satisfactory mass transfer of the oxygen from the air to the slurry. Table I shows typical chemical, screen, and

Jan 1, 1961

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1941

By P. D. Rao, H. B. Charmbury, D. R. Mitchell

As a result of a changing market pattern for anthracite, there is now an increasing demand for steam size and a decreasing demand for domestic sizes. To help the producer meet this new demand, the authors present the technical aspects of the problem of crushing domestic sizes to steam fineness and size. The market pattern for anthracite coal has changed considerably in recent years. The demand for domestic sizes has been gradually decreasing and the demand for the steam sizes has been increasing. The companies however aim for a maximum production of domestic sizes, since these sizes command premium prices. To meet the market demands, particularly in certain periods of the year, further size reduction of the coarse clean coal is necessary. The present practice of multistage crushing in toothed rolls leads to complicated flow arrangements and is high in cost. Data presented herein indicate that crushers with high reduction ratios could be used with a resulting simplification of crushing flows and an appreciable reduction of capital and operating costs. The different types of crushing equipment investigated included the rotary-type breaker, the jaw crusher, the impactor-type crusher, and the Aerofall mill. CURRENT PRACTICE The standard sizes of anthracite are presented in Table I and market specifications require that any given size be maintained with only a limited amount of oversize and undersize material. The 1958 prices of the various sizes also are presented, so it may be seen that size reduction is only performed when dictated by market demands. At the present time the general practice of crushing anthracite consists of removing the top size and crushing it in a toothed double roll crusher to the next largest size. Consequently, to reduce the domestic egg, stove, and nut sizes to steam sizes of pea, buck, rice, and barley, the original material must be screened to produce the three top sizes and each size must be crushed in three separate rolls to the next largest size. Each crushed product must then be rescreened to remove the oversize for re crush ing. Thus a typical operation would consist of scalping the egg size from a mixture, crushing it to stove size, and rescreening the product. This same cycle would be repeated for the stove and nut sizes requiring three screens and three crushers as well as conveying equipment to handle the crushed products. This results in an expensive series of operations to make a product which sells for a lower price. If the three top sizes are crushed in one operation to the smaller sizes then the yield of steam sizes is low and the production of Nos. 4 and 5 sizes is large. These sizes sell for lower prices than the steam sizes. A typical operation is presented in Fig. 1. From the figure it may be seen that the original cleaned anthracite contains 67.4 pet domestic sizes, 26.4 pct steam sizes, and 6.2 pct fines. After multistage crushing of the domestic to steam sizes the composition of the product is 0.6 pct domestic sizes, 89.6 pct steam sizes, and 9.8 pct fines. From a technical standpoint these results are reasonable but the handling and crushing costs are

Jan 1, 1961

By B. D. Lichter

In a previous paper, Oelsen, Schuermann, and Hey-nertl pointed out the possibility of obtaining complete thermodynamic functions for alloy systems from calorimetric measurements alone. Specifically, if the heat content of a heterogeneous, multicomponent system is known as a function of temperature and composition, then it is possible to derive the heats, entropies, and free energies of formation of liquid phases and of solid intermediate phases of fixed composition. The authors present equations and graphical techniques applicable to eutectic systems and systems with intermediate phases without solid solubility at lower temperatures. eijering has considered possible extension of the treatment to systems with complete solid-state miscibility at lower temperatures; however, experimental difficulties practically restrict the method to systems with very limited miscibility in the solid state. The purpose of this note is to present an alternative derivation of the heats and entropies of formation of liquid phases and of solid intermediate phases from heat-content measurements alone. Fig. 1 shows three types of phase diagram to which the analysis may be applied. If the heat content is determined as a function of composition x, at temperature T, we have quite generally and the heat of mixing of the liquid is obtained directly from heat-content measurements. If the temperature T lies in a two-phase region (solid-liquid) then

Jan 1, 1967

By AUDLEY H. STOW

I. INTRODUCTION. THE general drift of the discussion as to the relative merits of pressure- and exhaust-fans has resulted, if we may judge from the prevailing practice, largely in favor of the latter. The subject has been hitherto treated, however, with special reference to highly gaseous mines, the effect of the form of ventilation upon dust-explosions having been too little considered. Even in mines containing practically no gas, dust-explosions may occur; and if, as I believe, pressure-fans are to be preferred for their effect upon dust, it may be worth while to reopen the debate, and to challenge the advisability of exhaust-ventilation under certain conditions. There are several forms of colliery-ventilation, which may be described as follows: Plain or simple pressure-ventilation, in which the fan acts as a pressure-fan, and the movement of coal is unobstructed at the surface by doors or equivalent devices in drifts or shafts, the traveling and haulage thus being in the return-current. Plain exhaust-ventilation, in which the fan acts as an exhaust-fan, the movement of coal being likewise unobstructed at the surface, and the traveling and haulage being in the intake. Obstructed pressure-ventilation, in which the movement of coal is obstructed at the surface, in order that the traveling and haulage may be in the intake. Obstructed exhaust-ventilation, in which the movement of coal is obstructed at the surface, in order that the traveling and haulage may be in the return. The apparent advantages in running a fan "pressure" during working-hours, and " exhaust" between shifts, seem to justify the recognition of this combination as a standard form of ven-

Feb 1, 1909

As one surveys the extensive taconite operations on the Mesabi Range, he may find it difficult to believe that only 15 years ago, the iron ore mining industry here was staring at its own imminent demise. Due to the high demands for iron ore during World War II the postwar period of 1946-1950, and the subsequent "police action" in Korea, there was rapid consumption of the Mesabi's already depleted ores, and some economists were giving the Range only 20-25 years of life. In the 13-year period 1941-1953, more than 850 million tons of iron ore were shipped to steel mills, an amount almost equal to the total production during the preceding 30 years. Proven ore reserves dropped from 1.1 billion tons in 1940 to 8.3 million tons in 1954, the largest decrease being recorded in the famed direct shipping ores.

Jan 9, 1968

By W. H. Bassett

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (1) Depth of deoxidation of copper heated in reducing gas is greater the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this difference in depth of deoxidation is that, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much mire rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900° C.; that is, deoxidation is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide present in the copper. IN 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: FIG. 1.-EFFECT OF TIME AND TEMPERATURE ON DEOXIDATION RATE OF 0.365-IN. COPPER BY ILLUMINATING GAS; COPPER PLUS SILVER, 99.983 PER CENT. Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By S. G. Gibbs, A. B. Neely

Jan 1, 1967

By C. S. Harloff, Frank R. Corwin

THE Nichols Copper Co., associated with the Phelps Dodge Corp. and the Calumet & Arizona Mining Co., has constructed at El Paso, Tex., and is now operating a copper refinery with a yearly capacity of 100,000 tons of anodes. Transportation facilities were perhaps the most important of the considerations that led to the selection of this site. The rapid industrial development of the Middle and Far West has increased the consumption of copper there. The advantage of local refining as against shipping the copper to the Atlantic sea- board is apparent. Copper refined in the Southwest is equally competitive for export shipment, either from the Gulf or the Pacific Coast ports. The tonnage of copper produced in the Southwest not only justifies the construction of this plant, but may warrant considerable expansion in years to come.

Jan 1, 1930

By A. R. Kinkel

Robert T. Walker and Woodville J. Walker (Walker Engineering Corp., Salt Lake City)—Mr. Kinkel's article embodies, in condensed form, the results of the first detailed and complete geological survey that has ever been made of the long neglected but potentially very important West Shasta Copper-Zinc district, in Shasta County, California. In view of the difficulties of the terrain and the complexity of the geological structure, this represents a notable achievement, and it is with regret, therefore, that the writers find it necessary to differ from Mr. Kinkel's conclusions on two important points. The first has to do with the interpretation of two members of the stratigraphic column of formations in the district; for purposes of comparison, the description of these two members according to Mr. Kinkel is shown parallel to the description of these members according to the writers, see Fig. 14, Mr. Kinkel's nomenclature being used. The first member, which Mr. Kinkel terms the upper unit of the Balaklala rhyolite, consists of a single, massive, homogenous body of very silicious igneous rock, consisting almost wholly of quartz and albite, and averaging about 80 pct silica. Most geologists of the U. S. Geological Survey who have previously inspected the district have called it an alaskite. It is not a pile of several members, but is a single unit, without internal subdivisions. It has the form of a recumbent lens, approximately flat on the bottom and arched on top, several miles in diameter, and attaining a maximum thickness of 1000 to 1200 ft. It varies in texture from porphyritic to holocrystalline, and contains unusually large quartz phenocrysts up to 4 mm diam. Mr. Kinkel considers this formation to be a thick lava flow that is older than the overlying Kennett shale, while the writers interpret it as being intrusive, constituting a domed sill or laccolith that is younger than the Kennett shale. Their reasons are as follows: 1) This formation shows none of the features which within the writers' experience invariably accompany very silicious lava flows. Nowhere is it vesicular; nowhere does it contain any glass or its devitrified equivalent; nowhere does it contain flow breccia; and nowhere has it a ragged top, in spite of the fact that there is no evidence of surface erosion, which might have removed such a top.

Jan 1, 1957