Search Documents

By H. W. Miller, V. H. Wilhelm

During 1932 the oil industry persistently endeavored to maintain a rate of production that would permit a profitable price structure. Much effort was concentrated on curtailment of both production and drilling. The tendency in curtailment was to shut in reserves where closely held and not subjected to drainage, and to allow town-lot fields such as Long Beach, Santa Fe Springs, Playa Del Rey and Huntington Beach a greater percentage of allotment. Marginal wells were given special consideration; only a small percentage of curtailment wag required, making their operations profitable. Naturally the decline in production of town-lot fields, under slight curtailment, is very rapid, hence production that is restricted in fields controlled by major interests at the present time will profit considerably in the future, as California reserves do not appear adequate to sustain heavy withdrawals over a long period of time. California production during 1932 was much greater than additions to reserves during the year. The state produced 10,701,238 bbl. of crude oil less in 1932 than in 1931, while total stocks (all petroleum commodities) decreased 1,589,524 bbl. Had all operators kept strictly within their allotted 'production, the total crude production decline would have been approximately 20,000,000 bbl. and total stock decrease 3,000,000 barrels. Estimated proven oil reserves for California were 3,965,000,000 bbl. on Jan. 1, 1932, as compared with 3,784,120,000 bbl. as of Jan. 1, 1933, a decrease of 180,880,000 barrels. Approximately 85 per cent of the 178,127,794 bbl. of oil produced during 1932 was withdrawn from old reserves in settled fields and the remaining 15 per cent from new sources such as Kettleman Hills North Dome, Belridge, San Miguelito and Dominguez deep zone. The oil reserves of Kettleman Hills North Dome are estimated to be approximately 50 per cent of the total oil reserves, of California and they may be drawn upon at a much greater rate than the remainder of the state's oil fields.

Jan 1, 1933

By I. N. Knapp

I Herewith present some notes on the use of Portland cement to cement in the casing, and for plugging, to exclude water from oil and gas wells, and the methods employed. I have used my best efforts to. make each step of the operation of cementing wells perfectly clear. The information is the result of actual experience and observation. The illustrations are from original drawings made especially for this paper. Portland Cement It is not necessary to discuss here the manufacture of cement. Any established brand of the slower setting Portland cements may be purchased with the confidence that it will harden, if properly used, and exclude water from and plug wells efficiently. Setting.—By the setting of cement is meant its initial change from a soft or plastic mortar to a friable solid. After the cement has become thoroughly set it is still very weak and can be readily pulverized in the fingers. Setting is thought to be effected by the crystallizing out of the silicate and the aluminate of lime, which are soluble in water in their anhydrous form. After dissolving in the water they pass to the hydrated state, in which they are insoluble, and hence are precipitated in a crystalline form. Ordinarily neat Portland cement mortar remains perfectly plastic for from 1 to 1 1/2 hr. after mixing with water at about 70" F. A higher temperature accelerates and a lower retards setting.. Hardening.—This is due to a continual crystallization of salts from solution, and to further chemical and physical changes which develop slowly, but which continue for long periods of time. Testing.—It is no more necessary for an operator to go into the scientific testing of cement to be used in a well than to so test the pipe used. He must depend for the quality of each on the tests and reliability of the manufacturer. Cement or pipe may be damaged in shipment so

Jan 1, 1915

By J. A. Holmes

Venezuela has continued during 1929 to demonstrate that it is destined for many years to come to be one of our most important sources of crude petroleum. The producing fields of the Bolivar Coastal district along the east side of Lake Maracaibo have continued their phenomenal production, and two new fields have reached the near producing stage, while the results of deep test wells have strengthened the predictions and expectations that oil will be found and produced from many other pools and from several different geological formations. The finding of these new oil pools is not going to be easy, because the surface evidences of geological structure are scanty, and the subsurface problems are difficult, but intelligent effort backed by ample resources may be counted upon to overcome these obstacles and lead to a continued increase in the number of producing fields in Venezuela. During 1929 the total production of Venezuela was approximately 135,953,000 bbl., an increase of nearly 30,000,000 bbl., or 28 per cent., as compared with the preceding year. During 1929 oil in steel storage in Venezuela decreased from 13,000,000 to about 11,000,000 barrels. Tables 1, 2 and 3 briefly summarize Venezuelan production by fields and by years, and show the trend of production since its establishment on a commercial basis. Table 1.---Production of Crude Oil in Venezuela by Years, 1917 to 1929 All Figures in Barrels of 42 Gallons Total PRodUction Total PRoduction Year VeneZUela, Bbl. Year Venezuela, Bbl. 1917....................... 227,000 1927.................... 63,181,000 1918....................... 368,000 1928.................... 106,000,000 1919....................... 258,000 1929.................... 135,953,000* 1920..................... 548,000 Grand Total Since Ineep- 1921...................... 1,544,000 tion................... 380,791,000 1922....................... 2,448,000 Increase, 1929 over 1928.. . 29,953,000 1923..................... 4,170,000 Per cent. Increase......... 28.2 1924....................... 9,234,000 Per cent. 1929 Production 1925....................... 20,219,000 of Total............... 35.7 1926....................... 36,641,000 * Includes estimate for closing period of 1929.

Jan 1, 1930

By T. S. Lundy, F. R. Winslow

DIFFUSION coefficients of Hf181 in the high-tem-perature bcc phase of reactor-grade hafnium were determined at temperatures of 1795° to 1995°C by standard lathe-sectioning techniques. The temperature dependence of the data may be described by an Arrhenius-type expression for this limited temperature interval. However, hafnium is classed with the "anomalous" bcc metals zirconium, titanium, and y uranium by the low values of Do and Q observed in this study. The hafnium metal was received as 1/2-in.-diameter crystal bar. Analyses by the Analytical Chemistry Division of Oak Ridge National Laboratory showed the major impurity to be zirconium— about 2.1 pct. The total interstitial content was about 225 ppm with 190 ppm of this oxygen. The Hf"' was supplied as HfC12 in HC1 solution by the Isotopes Division of Oak Ridge National Laboratory. The hafnium bar was cut into disk-shaped specimens 3/8 in. long. One of the flat faces of each specimen was metallographically treated and then the isotope was deposited by vacuum evaporation from a tungsten filament. A 3 by 3 in. NaI (Tl) crystal with a single-channel analyzer was used for counting y rays with energies of 0.3 to 0.7 Mev. The as-deposited layers of isotope had counting rates of about 200 counts per sec. Specimens were annealed in argon in a tantalum resistance furnace. Temperatures were measured with a microoptical pyrometer calibrated for the particular furnace sighting conditions. All sectioning was done by standard lathe techniques. Section weights were determined on a semimicrobalance. A density of 12.5 g per cu cm was used in determinations of section thicknesses. Activities associated with the various sections were measured and the penetration data were treated using the computer code by winslow.' In all cases, except for specimens annealed at temperatures below 1795°C, normal Gaussian penetration behavior resulted. At lower temperatures, plots of In A(x) vs x2 were nonlinear [~(x) = relative activity at a distance x from the

Jan 1, 1965

By John P. Harmon

This paper was written with two objects in view: (1) To describe in detail what has been done toward the ventilation of the main unit of the Portovelo mines and the results; (2) to give information that may be useful to anyone who may have to make a preliminary mine ventilation survey, with recommendations for the improvement of the existing system and finally the maintenance of the improved system. General Description The mining operations of the South American Development Co. at Portovelo, Province of El oro, Ecuador, are described here only briefly, as a full discussion does not fall within the scope of this paper. The orebodies are of the steeply dipping, gold quartz vein type, averaging about 2.0 meters wide. As shown in Fig. 1, the ore chutes are relatively far apart, making considerable development work necessary before connecting raises can be driven between the levels. Faulting' on a large scale and a parallel vein system have made long dead-end drifts and many crosscuts necessary in the exploration of veins. The ventilation of these dead ends is described under Auxiliary Ventilation. The method of mining2 is the filled rill stope method, similar to the method that is largely employed at the Butte mines. The main shaft of the mine is in the Amarillo Valley, on either side of which mountains rise abruptly to a height of several hundred feet above the collar of the shaft. Entrance is made to the mine: (1) Through the American shaft, which extends vertically from the surface to a depth of 1100 ft., of which only the first 700 ft. are in active use at the present time; (2) levels are driven from the American shaft at intervals of 30 m. (100 ft.), of which only the third, fifth and seventh levels need be considered in the ventilation problem; (3) adits at intervals of 30 m. (100 ft.), with a few exceptions, above the collar of the American shaft.

Jan 1, 1931

By J. L. Sepulveda, R. F. Yap, R. Jauregui

INTRODUCTION The Third Theory of Comminution, oftentimes called the Bond Theory, was first published by Fred C. Bond in 1952. Since then, it has been widely used in the milling industry to size crushing and grinding equipment as well as to predict and evaluate their performance. Although two other comminution theories were advanced almost a century earlier, one by Rittinger, 1867, and the other by Kick, 1885, their use was limited because they did not agree with actual commercial comminution systems (Bond, 1961). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced in particle breakage, and equals the work represented by the product minus that represented by the feed. For particles of similar shape, the crack tip length is equivalent to the square root of one-half the surface area, and the new crack length is proportional to [(1/vT - vF)]; where P and F are particles diameter of product and feed, respectively. For practical calculations, the particle diameter can be expressed in terms of the 80% passing sizes, P and F, respectively. Therefore, the work input is given by, [10 _ 10', W = Wi [7P_7F(1)] Where W = the energy input to the mill, (kwh/t) Wi = Work Index, (kwh/t) P = square sieve opening which 80% of the product passes, (microns) F = square sieve opening which 80% of the feed passes, (microns) Equation (1) is the mathematical statement of the Third Theory, or the Bond equation. Numerically, the work index is the energy required in kwh/t to reduce a given material from theoretically infinite feed size to 80% passing 100 microns. The work index of a particular material is determined in the laboratory by conducting the standard Bond grindability test. Bond developed separate tests for the rod mill and the ball mill. The simplified test method described in this paper, which is used at Anaconda Research Center to approximate the work index, is an alternative procedure to the ball mill

Jan 1, 1982

By J. B. Berkowitz-Mattuck, R. Hopper, L. Kaufman, E. V. Clougherty

MARNOCH has reported on the attractive high-temperature oxidation resistance of Hf-Ta alloys.' In view of current interest in these alloys, three Hf-Ta alloys were tested in the present study. These included a Hf-27Ta alloy and a Hf-20Ta-2Mo alloy which were supplied by Marquardt Corp. and a Hf-20Ta-Zr alloy provided by Illinois Institute of Technology Research Institute.' The microstructure of these alloys was heated inductively in a glass vacuum system; the oxidizing gas, helium carrier plus a known partial pressure of oxygen (35-102 Torr), was continually passed over the sample at temperature for a given time period. The concentration of oxygen in the gas stream was continuously measured by a differential thermal conductivity technique2 so that the rate of oxygen picked up by the sample could be obtained. The flow rates were 0.1 to 0.2 ft per sec in the vicinity of the specimen. The concentration of oxygen did not fall below 50 pct of the input level in any of the experiments. In several cases a single sample was exposed consecutively at a series of increasing temperature levels. In a second system at ManLabs, cylindrical specimens were exposed to flowing air in a z irconia tube which was heated by radiation from a carbon tube resistance furnace. The specimen was heated from room temperature to the test temperature in flowing argon, then oxidized in air flowing at 0.1 to 0.2 ft per sec. Following exposure, the air was displaced by argon and the specimen was cooled. Postoxidation metallography was performed on every sample. The depth of conversion of the metal matrix to oxide was measured as shown in Fig. 1. The conversion depth was obtained by measuring the oxygen-contaminated metallic zone (which is bounded by a dense outer oxide and a subscale oxide region), subtracting its dimensions from the original dimensions, and dividing by two. Preferential oxidation of

Jan 1, 1968

By B. B. Zavoico, J. G. H. Crump, P. P. Gregory

West Texas was the scene of greatly increased oil activity during 1937, producing 75,743,000 bb1.l in that year as compared with 61,901,-000 bb1.2 in 1936, an increase of 22.36 per cent. The annual total of wells completed increased from 15863 in 1936 to 28062 in 1937, an increase of 76.92 per cent. Of the total completions in 1937, 2464 were oil wells,2 11 gas wells2 and 331 dry holes.2 The marked increase in the number of oil wells completed in West Texas during 1937 had a substantial effect upon the daily average production per well, which decreased 20.84 per cent from December 1936, when a total of 5310 wells3 produced 5,236,467 bbl.3 for an average of 31.81 bbl. per well per day to December 1937, when 7571 wells2 with a total production of 5,910,257 bb1.2 averaged 25.18 bbl. per well per day. Drilling blocks and checkerboard acreage were being acquired following geophysical work in the northern end of the Permian Basin area, composed of Bailey, Cochran, Hockley, Yoakum and Terry Counties, presaging extension of active development northward. During 1937, at one time 30 geophysical crews were working in West Texas, and an average of 15 to 20 crews was active in this area throughout the year. Discoveries Wasson-Denver Field.—Wasson-Denver field in Gaines and Yoakum Counties was the outstanding field discovery of the year. Production is from porous limestone found at about 5000 ft., and an average well is good for from 300 to 500 bbl. of crude oil per day through 3/4-in. choke. The discovery well was drilled by A. G. Carter and others on the Wasson Ranch, Gaines County, and the field has since been extended into Yoakum County. At the year's end 21 wells had been completed, producing

Jan 1, 1938

By H. W. Camp

The past year has had no revolutionary change in the process of petroleum refining, although there have been improvements and developments in practically every phase of operation, due largely, perhaps, to economic pressure. A few years ago, a Mid-Continent skimming plant using 35 gravity crude obtained 28 per cent. gasoline and naphtha; 9 per cent. kerosene, and the remaining yield gave gas oil and fuel oil. Figuring manufacturing cost, but not including sales, transportation, overhead and depreciation, the realization was $1.45 per bbl. of crude. Today, a thoroughly modern and up-to-date skimming plant, having all latest equipment, shows a realization of $1.74 per bbl. on the same basis. Thus it is evident that progressive developments have taken place in the last 2 or 3 years when potential earnings have been increased about 20 per cent. The average refiner is compelled to exert his utmost ingenuity in order to operate with a profitable margin. He has two factors to consider—recovery of maximum yields of profitable oils and the reduction of operating expenses. For the past 8 years, the margin between price of gasoline and cost of crude has grown narrower, constantly. Both these prices are determined by external conditions and not by the refiner himself, but the refiner might have been able to increase that margin had he more carefully controlled his output, limiting his production of light oils to current consumption. Be that as it may, this same economic pressure has given impetus to progress in improvements of primary distillation equipment, including stills, towers and heat-saving devices. A pipe still and bubble cap fractionating equipment can now replace a battery of shell stills, giving better yields, better control, elimination of rerunning and lowering of operating costs. The most recent pipe stills are being equipped either with radiant-heat furnaces or air-preheating systems and improved heat exchange equipment. These can be operated on a fuel consumption as low as 1 per cent. of the charge as compared to a fuel consumption of

Jan 1, 1929

By Charles L. Harness

MINERAL pigments give color, opacity, or body to paint, stucco, plaster, mortar, cement, linoleum, rubber, and similar materials. They must be finely divided, substantially insoluble, and generally inert for such uses. Inorganic pigments may be grouped somewhat arbitrarily as follows: A. Natural mineral pigments dug from the earth. 1. Those consisting mostly of iron oxides, such as hematite and Limonite. 2. Those containing large amounts of clay or noncoloring matter, such as ocher, sienna, umber, and colored shales. 3. Those whose color is not due to iron oxide, such as Vandyke brown (including sap brown, an alkali extract of Vandyke brown), graphite, and terre verte. B. Synthetic pigments. 1. Those containing iron oxide as the essential coloring matter, such as "pure" reds, yellows, and blacks, and Venetian reds. 2. Those not containing iron oxide, such as lithopone, zinc white, titanium white, ultramarine, Prussian blue, and the like. Only groups A and B-1 are discussed here. All the pigments in those two categories, except Vandyke brown, sap brown, and some of the carbonaceous slates, contain, as their essential color constituents, one or more compounds of iron; namely, an oxide-Limonite (2Fe203.H20 to Fe203.4H20), hematite (Fe203), or magnetite (Fe203.FeO). Man's first permanent coloring materials were earth pigments- the ochers, iron oxides, and various iron-stained clays. The caves occupied by prehistoric man and the arts of the ancient Chaldean, Egyptian, and Cretan civilizations bear mute witness to this and also testify to the beauty and permanence of earth colors. As the Roman era developed, earth pigments were pushed from their pre-eminent position by white lead and red lead and in the Middle Ages by zinc oxide. Today, of course, the number of acceptable pigments is very large and on a value basis the group of natural and synthetic earth pigments stands

Jan 1, 1949

By F. J. Tuck

THE Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a 3/4-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 clays. Manganese-steel lifter bars, 3 5/8 in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 clays. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1 1/2 -in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood hacking is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots; and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 2.5 to 33 per cent of the ore. Addi-tional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department.

Jan 1, 1938

By W. H. Burke

Deeper drilling, resulting in greater circulating distance and pressure, has directed attention to the advantages of the study of properties and control of rotary muds, which until recently have not had much consideration. One fundamental property of muds is viscosity, and viscosity is influenced by the quantity and character of colloidal material and can be controlled by chemical treatment. Colloidal Matter of Rotary Muds Two types of colloids are found in muds; the hydrophobic and the hydrophilic. Hydrophobic colloids do not associate intimately with water and are sensitive to small quantities of electrolytes. Hydrophilic colloids associate intimately with water, but are not so sensitive to electrolytes. The colloidal particles of rotary muds are derived from clay; In clay the particles may range in size from submicroscopic to macroscopic; a substance is a clay if the greater proportion of the particles are within the size limits prescribed for clay. The larger particles are inert and have no effect on the viscosity of normal hydrophobic colloidal muds. There are two theories accounting for the colloidal properties of clay-water suspensions: (1) the physical theory, that clay in water is a coarse colloidal suspension, and (2) Ashley's1 theory, that clay is a granular material with a colloidal gel surrounding the crystalline grains. The most important colloidal substances known to exist in clays besides the clay particles are: (1) colloidal silica, (2) colloidal alumina, (3) colloidal ferric hydroxide, (4) colloidal silicates, and (5) colloidal organic matter. Plasticity, a peculiar property of clay-water suspensions, is due to the colloidal particles. It is commonly (although not with strict accuracy) measured in terms of viscosity, and depends upon the amount and the state of flocculation of the colloidal matter present in the suspension. Fluidity in a rotary mud may be caused by a lack of colloidal clay particles or by deflocculated or flocculated clay particles, while viscosity in a

Jan 1, 1935

By E. M. Frizzell

Introduction In 1956, the first mobile crusher was installed in a limestone quarry in Hover, Germany. These early mobile crushers solved the problem of wet and soft ground conditions that did not permit the use of haulage trucks due to the high cost of building and maintaining the haulage roads. Quarry operators also wanted to take advantage of continuous belt conveyor haulage systems and the resulting cost savings. European mines, particularly the coalfields, are in soft materials that allow use of bucket wheel excavators and their following continuous haulage system of belt conveyors. Quarry operators, with this background knowledge of belt conveyors in mining, easily accepted the conveyor concept, once in-pit mobile crushing solved the problem of size reduction of mine-run-rock required for conveyor application. Four years after the initial mobile crusher installation, the first report published on the subject appeared in the December 1960 issue of Mining Engineer (Kochanowsky, 1960). With this early background and basis for direction, mobile in-pit crushing and conveying have increased to more than 74 installations. The capacity, type of crusher, and material being processed appear in Table 1. These data in Table 1 indicate that experience to data has been heavily influenced by limestone installations of less than 1 kt/h (1102 stph). Most of these installations were directly fed by a mine face excavator because of the limestone quarry ground conditions. Crusher Configurations Crushers systems developed to date have varying mobility capabilities. These range from fully mobile units that are used continuously in this mode to fixed, permanently located in-pit crushers. The following terms are presented to help distinguish the range of mobility within the configurations of "mobile" crusher systems planned or now in use. Mobile Crusher The crusher works at the mine face, is directly fed by an excavator, and moves in unison with the excavator on its own transport mechanism as the mining progresses. An example is the unit delivered in 1976 to Yamama Cement Co. in Reyadh, Saudi Arabia.

Jan 1, 1986

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By W. F. Carew, F. A. Crossley

Tensile, creep-rupture, and stability tests were employed to evaluate the effect of a-strengthening and ß-complexing additions on the base composition Ti-6Al-3Mo. The ultimate objective was to produce an alloy of greater strength than the Ti-7A1-3Mo alloy. Strengthening of a was accomplished by additions of 2 and 4 pct Ge, 4 pct Sn, 4 pct Zr, and 2 pct Sn-2 pct Zr. Making the ß more complex while keeping the total of ß-stabilizing additions constant at 3 pct resulted in higher tensile strengths but lower creep and rwpture strengths, especially at 1000°F. None of the more complex versions of the base alloy offers greater promise than the Ti-7A1-3Mo alloy. However, some improvement in the strength of the latter may follow from additions of zirconium perhaps up to 4 pct. PREVIOUS work directed at the development of titanium-base alloys with: 1) minimum room-temperature tensile elongation of 10 pct in 1 in., 2) high creep resistance at elevated temperature, and 3) the ability to retain original room temperature tensile ductility following exposure to creep conditions at elevated temperatures, demonstrated Ti-Al-Mo ternary compositions in the range 5 to 7 pct Al-3 to 6 pct Mo to be the most promising. Of this group the Ti-7Al-3Mo alloy was the strongest.'-= The objective of the present work was to determine if alloys of this type could be further strengthened by making additions which dissolve preferentially in the a-phase and by making the ß-phase more complex. For this study the base composition Ti-6Al-3Mo was selected rather than Ti-7Al-3Mo in order to minimize the possibility that in a more complex alloy with a-strengthening additions, low ductility might obscure the strength contribution. The metals

Jan 1, 1959

By Roy Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe¬rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By Roy A. Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a superior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By A. E. Harnsberger

I is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practically every refinery operation, from the charging of crude oil to a distillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from — 50" F. to 900" F. Pressure may vary from subatmospheric to 2000 1b. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of —50" F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200" to 900" F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250" F. The second type of corrosion occurs in high-temperature pumping equipment, with temperatures from 450" to 900" F., largely caused by sulfur compounds. There are also other corrosive conditions met with in refinery operations, particularly in the handling of acids, acid sludges and other specialized processes. These problems, although difficult to

Jan 1, 1935

By A. E. Harnsberger

I is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practically every refinery operation, from the charging of crude oil to a distillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from — 50" F. to 900" F. Pressure may vary from subatmospheric to 2000 1b. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of —50" F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200" to 900" F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250" F. The second type of corrosion occurs in high-temperature pumping equipment, with temperatures from 450" to 900" F., largely caused by sulfur compounds. There are also other corrosive conditions met with in refinery operations, particularly in the handling of acids, acid sludges and other specialized processes. These problems, although difficult to

Jan 1, 1935