Search Documents

By Richard Moldenke

One of the little-known characteristics of cast iron, which nevertheless has an important bearing on results where accuracy in machining is essential, is the ability of this material to ease up internal strains when allowed to remain quiescent for a more or less extended period of time. It seems as if the molecules in such a casting, by virtueof their "mobility," can adjust their relative positions to an extent sufficient to overcome some of the existing stresses. The following instance will perhaps give a fair idea of the condition a casting may be in when just shaken out of the sand. A very large sheave-wheel, after shaking out, was taken outdoors to be cleaned and made ready for turning up. It was leaned against the side of the building, but before much could be done an arm tore apart with a loud report. Investigation showed that the sun had been shining on the upper rim, thus adding a slight strain to those already existing within the arm and thus overbalancing the strength of the metal in tension. Had this sheave been kept under cover for a while, or at least until machined, the strains would have eased off sufficiently to allow the sun to look upon it without disaster. It will not be necessary to multiply examples. Every engineer knows the danger of water-hammer in pipe lines, particularly if the latter are of cast iron. Every mechanic knows, or should know, that it is not good to strike a fitting that is under steam pressure. It will be necessary to say a few words on the "internal strains" in castings—the so-called "casting strains" we hear so much about. We all know that to get a casting reasonably true to the dimensions wanted requires a slightly larger pattern. The usual allowance for gray iron is 1/8 in. to the foot (1 cm. per meter) and 1/4 in. to the foot (2 cm. per meter) for white iron (all dimensions). This reduction in length, breadth and thickness in a casting is erroneously called "shrinkage." It should be called "contraction," as for practical purposes it is simply the difference in dimensions of the casting red-hot and cold. The real "shrinkage" covers an entirely different situation. When a

Jan 1, 1917

By William Hague, Robert H. Bedford

The objects of this paper are: 1. To give cost data on drilling obtained at the North Star mine in California; 2. To describe the methods of testing drills employed there, giving the results of shop tests, and the correlated data obtained underground; 3. To demonstrate that these tests form a satisfactory basis upon which to judge rock drills. The rock at this mine is either close-grained diabase in the upper levels, or tough grano-diorite in the lower levels. The vein, which has an average dip of 23", consists of about 5 ft. of " formation" lying between walls of unaltered country rock. Of the 5 ft., solid quartz and stringers make up 18 in. of pay ore. The formation, which consists of but slightly altered country rock, is almost as hard as the unaltered walls. From 4 to 44 ft. is sent to the mill. One-third of the holes are drilled in the quartz; two-thirds in the formation. The holes are about 4 1/2 ft. deep and break on the average of 1.15 tons per hole. The average number of holes per stope drill shift is at present 5.65. The number of drill shifts throughout the mine in 1913 was 18,679, and the cost of labor for drilling, power, supplies, upkeep of machines and air lines, tool sharpening, and distribution, amounted to 33 per cent. of total mining expense. To do this work there are in commission 43 No. 12A, three No. 17V and eight No. 16V Waugh stopers, three Jackhamers, two Waugh pluggers, and 17 No. 8 and two NO. 7 water Leyners. For the past three years a record has been kept of the repairs on each machine and number of shifts operated by it. The figures given in Tables I and II for the cost of repairs per drill shift have been taken from this record. The underground air pressure is about 90 lb. The air consumption per drill shift was measured by aerometers. The leakage of pipe lines between compressor and meter is not included. From the number of pieces of steel sharpened for each type of drill during the year the average used per drill shift has been ascertained. For other supplies the figures given represent a year's average.

Jan 1, 1915

By K. J. Powers

The Mine Accident, Injury, Illness and Employment Database at the Mine Safety and Health Administration's Health and Safety Analysis Center is a computerized system that stores accident, injury, illness and employment data about all coal and metal/nonmetal mines in the United States. The paper discusses the system for collecting, storing, analyzing, and reporting this information and how these data are used in the ongoing effort to increase the health and safety in this nation's mines.

Jan 1, 1983

By R. D. Daniels, T. W. Wood

The tensile properties of columbium and Cb-H alloys containing up to 455 ppm H were studied as a function of temperature and strain rate. Hydrogen, introduced into columbium at elevated temperatures, using a thermal -equilibrium technique, embrittled columbium most severely at about —77°C. This elnbrittle ment occurred even at hydrogen concentrations of an order of 20 ppm. At higher temperatures, the hydrogen tolerance of columbium increased in relation to the increased solubility of hydrogen in tile metal. Below this temperature hydrogen tolerance, as determined by ductility and fracture stress, increased slightly. Strain rate had little effect on the tensile results for cross-head speeds over the range 0.002 to 2.0 in. per min. Strain aging during the tensile test appears to explain the ductility mininmum at —77°C. The apparent increase in hydrogen tolerance at lower temperatures is attributed to the low mobility of hyhogen. Experiments were performed in which samples were prestrained in tension at room temperature and tested to failure at —196°C. Results suggest that hydrogetz segregation to preformed crack nuclei can cause subsequent embrittlement even at temperatures where hydrogen mobility is too low to cause embrittlement in a normal tensile test. COLUMBIUM is an example of the class of bcc metals with ductile-brittle transition temperatures sensitive to the presence of interstitial atom contaminants. Hydrogen is one of these embrittling contaminants. The embrittling effect of hydrogen is less potent, perhaps, in columbium than in some of the other bcc refractory metals, but it is still a problem of both theoretical and practical interest. Unlike hydrogen in iron and steels, hydrogen in columbium is exothermically rather than endo-thermically occluded. The embrittlement process in exothermic systems has not been studied as extensively as that in endothermic systems, especially at hydrogen concentrations below the limit of solubility. The purpose of this investigation was to evaluate the embrittlement process in initially pure columbium as a function of hydrogen content, temperature, and strain rate. The Cb-H phase diagram, according to Albrecht et al.,1 is shown in Fig. 1. Columbium reacts exothermically with hydrogen producing a solid solution at concentrations of less than about 250 ppm (parts per million by weight) H at room temperature. At concentrations above the highly temperature-dependent solvus a second phase is formed. Like many similar hydrogen-metal systems,2 his system exhibits a miscibility gap with respect to hydrogen solution. Albrecht found the critical temperature of the miscibility gap to be about 140°C, the critical concentration to be 0.23 atom fraction hydrogen, and the critical pressure to be 0.01 mm Hg. Above 140°C there is a solid solution of increasing lattice constant extending across the phase diagram. Hydrogen concentrations of particular interest in this investigation were those below the limit of solubility in columbium. At hydrogen concentrations above the limit of solubility, columbium will contain the hydrogen-rich second phase and will be brittle under most testing conditions because the hydride generally precipitates as platelets with coincident matrix lattice strains.1'3 At hydrogen concentrations below the limit of solubility, the tensile behavior of columbium is expected to be more sensitive to the interrelationships between hydrogen concentration and mobility and the testing variables such as temperature and strain rate. Literature references to the hydrogen embrittlement of metals, especially ferrous alloys and titanium alloys, are too voluminous to mention. It is only recently, however, that detailed studies of the hydrogen embrittlement of columbium have been undertaken. Wilcox et a1.4 studied the strain rate and temperature dependences of the low-temperature deformation behavior of fine-grained are-melted columbium (1 ppm H) and the effect of hydrogen content (1,9, and 30 ppm H) on the mechanical behavior of columbium at a series of temperatures for a single strain rate. A strain-aging peak was ob-served at about -50°C which was attributed to the presence of hydrogen in the metal. Eustice and carlson5 studied the effect of hydrogen on the ductility of V-Cb alloys at a series of temperatures over the range -196° to 25°C. Pure columbium was embrittled by 20 ppm H which produced a ductility transition at approximately -70°C. Ingram et al.6 studied the effect of oxygen and hydrogen on the tensile properties of columbium and tantalum. A minimum in the notched-to-unnotched tensile ratio of hydrogenated columbium was obtained at about -75°C, but because of the relatively large hydrogen content employed (200 and 390 ppm) the ductility

Jan 1, 1965

By G. P. Airey, R. F. Mehl, T. A. Hughes

The coarsening of cementite particles in a ferrite matrix has been studied in a series of steels with 0.15 pct C only and 0.15 pct C plus 1 pct Ni, Mn, and Cr, respectively. Two initial states were employed: quenched nartensite, and quenched and cold-rolled martensite. A series of tempering temperatures between 500' and 700" and tempering times of up to 190 hr were used. The structures were studied by replica and transmission electron microscopy. Particle size distribution curves were determined. From the average size value coarsening curves were obtained. These were plotted in accordance with the Wagner analysis assuming diffusion control. A discussion of the significance of the results is given. L HE reactions occuring upon the tempering of martensite have long engaged the attention of metallurgists. The latter stages, when cementite particles coarsen in a ferrite matrix, have been studied both qualitatively and quantitatively. Studies of such coarsening processes have recently been spurred by the publication of the Lifshitz-Wagner theory1, and the extension of this to the a Fe-Fe3C system by Oriani3 and by Li, Blakely, and einold. Following Wagner the coarsening process is often designated as "Ostwald Ripening". The only quantitative data on the rate of coarsening, except for the work of Hyam and uttin,' in the a Fe-Fe3C system are those of Bannyh, Modin, and odin' for a commercial eutectoid steel and those of Heckel and ereorio" using a pure eutectoid steel. The data of Bannyh, Modin, and Modin have been employed by 0riani3 to derive the a Fe-FeE interface energy. The reaction is one of the most important ones in steel and is worthy of detailed study. This is the purpose of the present study. Laboratory heats were prepared; these were steels with approximately 0.15 pct C, selected so that the num ber of carbide particles would be relatively small and thus so that the overlapping diffusion fluxes would be minimized, presumably a desirable circumstance.'-3 In addition to Fe-C alloys, comparable heats containing 1 pct of Ni, Mn, and Cr, respectively, were included with a view of appraising the effect of alloying elements. This report includes an account of the micro-structures observed, primarily with the electron microscope, and of kinetic data and their interpretation. MATERIALS AND TREATMENT The alloys were prepared from electrolytic iron ("Plastiron") and high-purity graphite; these were melted in a zirconia crucible using a vacuum furnace. The alloy steels were made by adding electrolytic nickel, electrolytic manganese, and "vacuum grade" chromium, respectively, under a partial pressure of argon. Each melt was poured into a mold within the vacuum furnace and cooled in the mold. The ingots were 2 in. in diam. and 8 to 10 in. long. The analysis of the alloys is given in Table I. These ingots were hot-rolled to strip 0.1 in. thick, then cold-rolled to 0.05 in. and each alloy split into two batches. One batch was austenitized at 1200 for 1 min, quenched in cold brine, then cold-rolled to 0.02 in.; samples given this treatment are hereinafter designated as "worked". The other batch was cold-rolled to 0.025 in., austenitized at 1200" for 1 min, and quenched in cold brine; such samples are hereinafter designated as "quenched". These two batches were then tempered, as below. The purpose of the treatment given the first batch was to provide an initial structure of cold-worked martensite, with the expectation that the additional defect structure created by cold work would encourage a higher rate of nucleation of cementite on tempering and hence a more uniform distribution of cementite particles. Individual specimens were sealed in evacuated quartz or Pyrex tubes, then tempered in a muffle furnace. The temperature control was better than 3'C at 700. Tempering treatments wer: performed at 400°, 500°, 550°, 600°, 65o°, and 700C for time periods between 15 min and 190 hr. PREPARATION OF SPECIMENS Specimens for optical and replicalelectron microscopy were mounted, polished conventionally, and etched with 2 pct nital. For electron microscopy, single-stage "formvar" replicas were made, dry-stripped and rotary-shadowed with chromium at an angle of 30 deg. Carbide extraction replicas were prepared from electropolished specimens usirig the method described by Smith and uttin.' Thin foils for electron transmission microscopy were prepared by chemical thinning in an H202-HF bath prior to electropolishing in a chromium trioxide-acetic acid solution. The most

Jan 1, 1969

By W. O. Philbrook, K. Natesan

The oxidation kinetics of spherical pellets of zinc sulfide made from Santander concentrates were studied using a thermogravimetric technique. The experiments covered a temperature range-. of 740" to 102O°C, 0-N mixtures varying from 20 to LOO pct O2, and pellet diameters between 0.4 and 1.6 cm. Mathematical models were formulated to Predict the reaction rate on the assumption that a single transport or interface reaction step was rate -controlling. Analysis of the data indicated that the process of oxidation was predominantly controlled by transport through the zinc oxide reaction-Product layer. ROASTING processes, which are reactions between solids and gases, are very important because they are employed in the production of a number of basic metals. These processes are highly complicated, and one needs to consider the transport phenomena of heat and mass between the solids and gases in addition to the kinetics of various chemical reactions involved. Because of such complications there is a lack of knowledge concerning the rate-limiting factors, which may strongly depend on temperature, particle size, gas composition, and solid structure. The oxidation of zinc sulfide, which is of commercial importance in zinc production, falls into this class of reactions. The major goal of this work was to elucidate the roles played by different process variables, such as reaction temperature, gas composition, pellet size, and pellet porosity, on the kinetics of oxidation of single pellets of zinc sulfide. Roasting of zinc sulfide single particles has been a subject of both experimental and theoretical investigations.&apos;-&apos; The reaction is exothermic and may be considered to be irreversible. Such a reaction has been found to proceed in a topochemical manner. In other words, as the reaction proceeds, a progressively thicker outer shell of zinc oxide is formed, while the inner core of unreacted sulfide decreases. It has been found experimentally, both in the present work and in the previous investigations,1-9 that the particle retains its original dimensions and the process requires transport of gaseous oxygen across the porous product layer for continued reaction. The reaction may be represented by ZnS(s) + 3/2 O2(g) = ZnO(s) + SO2(g) [1] The solid product considered here is only zinc oxide, since the diffraction patterns of zinc sulfide pellets oxidized partially at &apos;798" and 960°C showed K. NATESAN, Junior Member AIME, formerly St. Joseph Lead Fellow, Department of Metallurgy and Materials Science, Carnegie-Mellon University, Pittsburgh, Pa., is now at Argonne National Laboratory, Argonne, Ill. W. 0. PHILBROOK, Member AIME, is Professor of Metallurgy and Materials Science, Carnegie-Mellon University. This paper is based on a them submitted by K. NATESAN in partial fulfillment of the requirements for the Ph.D. degree in Metallurgy and Materials Science at Carnegie-Mellon University. Manuscript submitted December 2, 1968. EMD lines corresponding to original zinc sulfide and the newly formed zinc oxide. OXIDATION MODEL The generalized model for gaseous oxidation of zinc sulfide is illustrated in Fig. 1. This depicts a partially oxidized sphere of zinc sulfide in a gas stream surrounded by a laminar film of gas. The spherical sample of zinc sulfide of unchanging external radius r0 is suspended in a flowing gas stream of total pressure PT and composition specified by the partial pressures of the individual components. Partial pressures of the gaseous species in the bulk gas phase, at the exterior surface of the pellet, at the ZnS/ZnO interface, and at equilibrium for Reaction [I] are identified by the superscripts b, o, i, and eq, respectively. The overall reaction involves the following ~te~s:&apos;~&apos;~&apos; Step 1. Transfer of reactant gas (oxygen) from the bulk gas stream across the gas boundary layer to the exterior surface of the pellet and the reverse transfer of the product gas (sulfur dioxide). Step 2. Diffusion and bulk flow of oxygen from the pellet surface through the product shell (ZnO) onto the ZnS/ZnO interface and the reverse transfer of sulfur dioxide. Step 3. Chemical reaction at the interface, which results in consumption of oxygen gas and generation of sulfur dioxide gas and heat; at the same time the _________ PARTICLE SURFACE / x^^^^n^X / MOVING INTERFACE core-----/ sJSNxy " /T^T^02 \ V\V$\ ^NWX/ "*/— GAS BOUNDARY x. \\ZnO SHELLV/ / \^ . / &apos; ^ BULK GAS --------N_______ _____,------p£ w \ P« / (f> \ / a \ <i) / <----------------- _(o) ^^--------------(b) °- pso, pso2 ro ri 0 ri ro RADIAL POSITION Fig. 1—Generalized model for oxidation of a sphere of zinc sulfide.

Jan 1, 1970

By F. H. Bunge, W. H. Jr. Dailey

This paper covers an investigation of the magnetic roasting characteristics of several iron ores when treated in the form of small pebbles (1/8" to 1/2" in size), and in the form of balled fines. The roasting treatment was carried out with apparatus capable of very close control of time, temperature, face velocity, and per cent combustible in the reaction gas. The effect of rapid initial heating was not studied although it is believed that this has a major effect on the results when processing solid pebbles. The test equipment is a fixed bed type, with such a wide range of gas velocities, temperature, combustible content and etc., that the results obtained can be made to approximate those from various commercial roasting processes. The data presented in this report covers reaction rates, effect of processing variables on silica in the concentrate, flow resistance of beds, and to a limited extent, the effect of particle size. The work is far from complete and raises many more problems than it gives answers for. We believe, however, that much of the information will be useful to those engaged in investigation of magnetic roasting processes. We measured the time required for various degrees of completion of the reaction of hematite to magnetite, for finely pound material in balled form and for carefully sized crushed ore. Measurements were made for a variety of Minnesota and Labrador ores. This report covers an ore requiring fine ginding (-325 M) for liberation (Lower Kevin) and an ore requiring coarser grinding (-100 M) for liberation (Upper Olson). These ores represent approximately the range of characteristics for a group in the west end of the Mesabi Range. Our data shows that the reaction rate is very fast for the finely ground material and that tests are readily reproducible. The reaction rate of the larger size material, in the range of 1/8" to 1/2", is much slower and the results more erratic. We found that for the ores tested, the percentage of silica in the Davis tube magnetic concentrate was a function of iron recovery. Normally the concentrate had a low and relatively uniform percentage of silica up to a critical value of recovery. Above this critical recovery value the percentage of silica increased very rapidly. For example, for one particular ore roasted in the form of 3/8" diameter balls made from -28 mesh fines, the silica remained at about 7% to 8% until the recovery exceeded about 93%. Increasing the recovery beyond 93% resulted in over 25% silica with the additional recovery. The degree of conversion of hematite to magnetite (% completion of roast) required to obtain 93% recovery for balled material, varied inversely with the gas flow rate. Percentage silica in the concentrate resulting from roasting 3/16" and 1/2" solid material was relatively erratic. However, for varying degrees of iron recovery the lowest silica percentages corresponded to those obtainable when roasting fines. It is thought the probable reason for the erratic values was the variation in shattering or cracking of the pebbles during initial heating and roasting. There is some indication that very fast initial heating will greatly increase the permeability of the individual particles of ore to gas flow so that the reaction rate for coarse sizes will approach that obtainable with balled fine material.

Jan 1, 1961

By H. C. Rogers, B. W. Roberts

Vanadium foils and wires, either cold-worked or recrystallized, show a ductile-brittle-ductile fracture sequence with temperature. At about 150°C the hydrogenated vanadium wires are found to be ductile. At room temperature the wires show brittle fracture, and at liquid nitrogen temperature the wires are again ductile, although to a lesser extent than found at 150°C. Hydrogenated cold-rolled vanadium foils have been found to fracture in unusually straight lines along the [100] texture directions. The hydrogen content required to show this [loo] texture fracture is limited to a few atomic percent in range. Hydrogen content above this range causes fracture to occur in random directions. PRELIMINARY experiments with hydrogenated vanadium foils indicated that the embrittling effect of the hydrogen on the vanadium, which was severe at room temperature, was reduced at both lower and higher temperatures. In order to investigate more quantitatively the ductility changes with temperature, vanadium wires were tested in tension at three temperatures. The reduction of area was measured and the fractures examined. Specimen Preparation—The material used was kindly supplied by A. U. Seyboltl in the form of M-in. rod. The nominal analysis was: 99.2 pct V assay, 0.2 pct C, 0.01 pct Si, 0.01 pct Fe, 0.015 pct Ca, 0.02 pct O,, 0.01 pct N2, and 0.003 pct H,. The specimens were 0.035-in. diam wires. These were prepared by cold-swaging the supplied rod to the final diameter without intermediate anneal. They were finished with long-bearing dies. The surface was then given a light polishing with 0 emery paper and degreased in trichlorethylene. An X-ray check indicated that the cold-swaged wire had a fairly strong [110] fiber texture. The wires were then recrystallized in vacuum in continuously pumped quartz tubes at two temperatures to give two different grain sizes. One group of wires was given 45 min at 800°C; another, 60 min at 1000°C. The microstructures in Fig. 1 show the wires after they have been electropolished and elec-troetched in 10 pct HCI. After the 800°C anneal, the vanadium grains had a diameter of 1 to 2p and there appeared to be a tendency to elongation in the longitudinal direction. However, the latter may be an etching effect. After the 1000°C anneal, the grains appeared to be equi-axed, but there was a very large spread in grain size, probably due to some impurity segregation in the wire, Fig. 1, right. The grain diameters varied between the limits of 1 to 150p. The small particles shown particularly clearly in Fig. 1, left, are also visible on the polished surface of all samples before etching and are undoubtedly carbides and nitrides of vanadium. An X-ray check indicated these annealed wires had a strong [110} recrystallization fiber texture. The hydrogenation was carried out in an iron retort with dry hydrogen flowing through it, the retort and contents being heated in a tube furnace with a hydrogen atmosphere. The hydrogenation temperature was approximately 500°C. The hydro-genation times chosen were approximately those which would be just enough to cause the vanadium to be brittle at room temperature and thus allow the greatest chance for ductility to occur at the other two temperatures. Part of the fine grained specimens were hydrogenated for 21/2 min at 490°C. Part of the coarse grained specimens were hydro-genated for 11/2 min at 515°C.

Jan 1, 1957

By M. B. Bever, A. B. Michael

THE structure of cast A1-Si alloys is altered profoundly by modifying agents. Sodium, in particular, reduces the size of the silicon particles in the eutectic and tends to change their shapes from plates to nearly rounded grains. This refinement is accompanied by a shift of the eutectic to higher silicon concentrations and lower temperatures. Similar effects can be attained by rapid solidification. Hypotheses advanced to explain modification have involved the formation of a ternary eutectic,1 the removal of oxides by fluxing,&apos; and even a presumed allotropic transformation of silicon. Other hypotheses assume that the modifying agent causes an envelopment of the silicon particles by the aluminum-rich solid solution, but attribute this envelopment to different mechanisms. According to various explanations, the growth of the silicon particles is obstructed by an immiscible sodium-rich liquid," an adsorbed layer of sodium,&apos; or a ternary compound;5 his obstruction has been conceived as purely mechanical or as a colloidal action.&apos; It has also been proposed that sodium reduces the surface tension on the Al-Si interface, thus permitting the aluminum-rich solid to grow faster and to envelop the silicon particles.? Still other hypotheses stress undercooling and the attendant change in the rate of nucleation of silicon, but fail to ascribe any definite function to the sodium addition." &apos;" Procedure High-purity alloys of aluminum and 3 or 7 pct Si were treated with modifying agents containing radioactive sodium tracers. The experiments were intended to investigate the partition of sodium between the primary aluminum-rich solution and the eutectic, and, if possible, to determine whether sodium is concentrated in or around the silicon particles in the eutectic. Radioactive sodium fluoride, alone or mixed with stable sodium chloride, was allowed to react with the alloy for 5 min immediately before solidification in the crucible. Modification could not be attained with additions of less than the equivalent of approximately 0.1 pct Na. Some alloys were not completely modified, but comparison of the structures of treated and untreated specimens indicated a very considerable reduction in particle size of the silicon in all of the former. A treated alloy is shown in Fig. 1. Radioactive sodium fluoride was prepared by bombardment with deuterons having an energy of 14 mev. This bombardment (totaling, for example, 6 microampere-hours in one run) produced radioactive Na24 (half-life 14.8 hr) by the reaction 11Na23 (d,p) 11Na24. The radioisotopes of fluorine also produced have short half-lives and were not detected. A half-life determination by counting confirmed that the measured activity was due to Na24. The distribution of the sodium in the solidified alloys was determined by an autoradiographic technique by which a suitable stripping film is attached to a very thin metallographic specimen. After exposure and development, this emulsion remains superimposed on the specimen and may be examined microscopically or photographed by reflected light. The emulsion of the autoradiograph can be correlated directly with the underlying surface by simple adjustment in focus. The details of this technique have been described elsewhere." Results Fig. 2 is a micrograph of the autoradiographic emulsion ("autoradiograph") lying directly above the area of eutectic in Fig. 1. Fig. 3 shows a similar autoradiograph of a region consisting of primary solid solution. The small black dots (tracks) in these autoradiographs are developed grains in the emul-

Jan 1, 1954

By R. J. Towner

Tensile properties of Aluminum Powder Metallurgy (APM) products at 600°, 800°, and 1000°F were lowered by cold reductions of as little as 10 or 20 pct. The detrimental effect of cold work on yield strength at elevated temperatures increased with temperature. Heating cold-worked products at 850° to 1150°F removed the structural effects of cold work through the process of recovery and restored, at least partially, the strength at 600°F to the level of hot-worked material. Material containing 5 pct A1203 was recrystallized by cold reductions of 97 pct or more followed by annealing at 1100°F. Recrystallization lowered sharply the strength at room temperature, but raised the strength at 600°and 800°F relative to that of the cold-worked state The high strength of Aluminum Powder Metallurgy (APM) products at elevated temperatures&apos;-4 is well-known. In this paper, some conditions of processing that can affect this important characteristic are presented. The following nomenclature will be used to identify different alloys: All of the above alloys are of the aluminum-aluminum oxide type made from milled powders of commercially pure aluminum with the exception of M486, which is fabricated from atomized A1-Fe alloy powder. The products made from milled powders are hardened by a dispersion of aluminum oxide par- ticles in the aluminum matrix, while the intermetal-lic compound FeAL is the dispersion hardening agent in M 486.&apos; The process used for making all APM products involves the application of heat and pressure to form a compact from powder which is fabricated into an extrusion, sheet, strip, or wire by standard techniques. Probably the most common cold-worked APM product is sheet. Cremens, Bryan, and rant&apos; determined the room-temperature tensile properties and the 600°F stress-rupture properties of XAPOOl and XAPOO3 sheet and reported that there was little difference between the as-extruded, cold-worked, and annealed at 1200°F conditions. On the other hand, Emmons6" found that the tensile and stress-rupture properties of XAPOOl and XAPOO3 sheet at 600" and 800°F were lower than those of extrusions. The tensile properties of XAPOO3 sheet were also determined at elevated temperatures by Doyle&apos; and ~ayward.&apos; According to Friske" and Kendal et a1.," cold working by swaging, rolling, and tube drawing reduced the tensile and creep-rupture strength of XAP 001 Recrystallized aluminum powder metallurgy products are rare because the dispersion in the aluminum matrix is usually too fine, uniform, and concentrated to permit recrystallization. However, Lenel12 was able to recrystallize wires made from aluminum powders containing about 1.75 and 3.0 pct oxide and found that the tensile properties at room temperature remained higher than those of annealed commercially pure aluminum because of the dispersed oxide particles. Westerman and Lenel13 found the kinetics of recrystallization of the powder products were very different from those of cold-drawn commercially pure aluminum wire. The alloy containing 3.0 pct oxide recrystallized to a very coarse grain size was more creep-resistant at 400" to 600°C (752" to 1112°F) than in the as-extruded, fine-grained condition, according to Ansell and weertman.14 Ansell and aenel" further studied creep at 500" to 620°C (932" to 1148°F) of recrystallized 1.75 pct oxide wire and confirmed the creep model of Ansell and Weertman. The present work is being reported for the fulfillment of the following objectives: 1) to show the effect of cold work on tensile properties at elevated temperatures;

Jan 1, 1964

By J. J. Cosgrove, J. E. Warren

A general model which approximates the effect of cross- flow has been developed to give a practical method for predicting the waterflood behavior of a stratified reservoir. The model is based on a modification of Dietz&apos;s theory and allows for variations in both the permeability and hydrocarbon pore volume. In the particular cases considered, it is assumed that the permeability can be characterized by a log-normal distribution and the hydrocarbon pore volume by a normal distribution. A simple graphical method which enables the practicing engineer to predict the behavior of a stratified system is presented The results obtained by the proposed method are compared with those obtained by the Dykstra-Parsons method. As a result of this study the following conclusions have been drawn: (1) The effect of cross-flow in a stratified system can be appreciable, particularly at very favorable or very unfavorable mobility ratios; (2) Under normal conditions, the effect of variations in the hydrocarbon pore volume can be neglected; and (3) The failure to use all of the available permeability data can lead to large errors in the prediction of the behavior of a stratified reservoir. INTRODUCTION Various methodshavebeenproposedto characterize and to predict the waterflood behavior of a stratified reservoir. Most of the methods assume that the reservoir is composed of discrete homogeneous continuous layers. With this model, the degree of stratification can be measured by several parameters based on core-analysis data. Among these are the Lorenz coefficient1 and the variation of a log-normal permeability distribution? The behavior of stratified systems is usually predicted by the Stiles, Dykstra-Parsons method or some modification of these. In both of these methods the reservoir is divided into discrete homogeneous layers with no cross-flow between layers. In the Stiles method the mobility ratio is assumed to be equal to unity while in the Dykstra-Parsons method it is allowed to take on any value. Other predictive methods have been proposed; method allows for cross-flow between the beds and a method by Schmalz and Rahme6 correlate.s the recovery directly with the Lorenz coefficient. In this new approach, which is essentially a continuous analog of Hiatt&apos;s method, the effects of both mobility ratio and cross-flow between the beds have been included. It is assumed that the permeability can be represented by a log-normal distribution and the hydrocarbon pore volume or porosity by a normal distribution. These types of distributions have been observed by several authors, 1,2,4 and most field data seem to confirm their observations; e.g., if these distributions are assumed and there is a 1:l correspondence between porosity and permeability samples, the commonly encountered linear relationship between porosity and the log of permeability is obtained. Since, in many field cases the permeability and poro sity data are truncated or cut-off at predetermined upper and/or lower values, the effect of discarding part of the data was investigated with the proposed method. A better technique for truncating the data is suggested. THEORY In the derivation of the method to be described in this paper the following assumptions are made: 1. Capillary forces are negligible per se; their effects are only manifest in the relative permeability curves. 2. The fluids are immiscible, incompressible and homogeneous. 3. The reservoir is horizontal and uniformly thick; it is initially liquid saturated i.e., connate water and oil. 4. The reservoir is composed of discrete layers, each having its own permeability, porosity and connate water saturation; each layer is homogeneous,

Jan 1, 1965

By A. E. Worthington, R. F. Meldau

An analog computer study was made of the reduction of the magnitude of the SP by formation geometry and resistivity effects. Practical field .situations were studied. The analog data were converted to the form of departure charts. These charts may he used to determine the reduction in the SP due to the above eflects pith good precision Quantitative interpretation of the SP log in terms of formation water resistivity is presently based on the premise that the observed SP is equal to the electrochemical potential developed across a shale between the mud filtrate and the formation water. This procedure inherently assumes that, first, no electro kinetic (streaming) potential is present, and, second, that the SP is not reduced by resistivity or geometry effects in the formation. When, however, such a reduction of the observed SP does occur, one may write, SP = b,E, b, E, (1) where SP is the observed self-potential opposite the center of the bed under consideration. In this case, E, is the electrochemical potential, E, is the electrokinetic potential, b, is the electrochemical reduction factor, and h, is the electrokinetic reduction factor. The first assumption above is equivalent to assuming E, = O in Eq. 1 and the second assumption is equivalent to h, = b, = 1. Examination of electric logs shows that for many formations of interest the observed SP is reduced below its maximum value. The object of this work is to aid quantitative SP interpretation in at least some of these situations by obtaining values for b, and b, in Eq. 1 as functions of realistic combinations of bed thickness, depth of invasion, and formation resistivity. The only previously published work in this field known to the authors is by H. G. Doll&apos; in 1948. He evaluated b, under conditions permitting exact analytical solution. His work clearly established the importance and qualitative nature of formation geometry and resistivity effects upon the SP, but the necessity of obtaining analytical solutions restricted his study to situations of limited practical interest. In order to extend such studies to practical combinations of formation parameters which do not lend themselves to feasible analytical solutions, the results reported in this paper were obtained by use of a special analog computer. THE ANALOG MODEL The analog model used for this study was the Guyed Analog Computer which originally was designed and built for resistivity log departure curve studies. It consists of a two-dimensional mesh of resistors, with the vertical mesh corresponding linearly to vertical distance along the borehole, and the horizontal mesh corresponding to radial distance from the borehole axis. By proper choice of horizontal resistor values, a three-dimensional, axially symmetric, borehole-formation problem can be modeled with this two-dimensional array. These and other details of the model are contained in a paper by H. Guyod&apos;. The geometry used for the SP studies with the analog is depicted in Fig. 1. This configuration has a horizontal plane of symmetry, and, hence, the model, and the following discussion, need only to be concerned with one quadrant such as shown in Fig. 2. A further simplification arises by considering that both the natural potential sources and those used in the model have fixed internal impedance. Therefore, the current flows produced by these sources can be separated and studied independently ( i.e., the superposition theorem can be applied). SP = SP, i SP, = h,E, + b,E, ,(7)

By Robert C. Bolger, John H. Weitz

REFRACTORY clay, one of Pennsylvania&apos;s important nonmetallic mineral resources, occurs at several horizons in beds of Pennsylvanian age. The Mercer fireclay, of Pottsville age (Table 1), is the most important of these clays. A study of this fireclay has been conducted by the Pennsylvania Geologic Survey discontinuously over a period of seven years. The work has included field mapping of a rather large area, as well as petrographic, differen¬tial thermal, and X-ray studies of the fireclay. A comprehensive report on the project is now in preparation.

Jan 1, 1952

Stripping of the Exotica open-pit mine, which is proceeding at about 120,000 tpd, is dwarfed by its proximity to the 500-million-ton Chuquicamata tailing pile. The excavating work is being carried on smoothly and efficiently and, as of the end of October, accounts for the removal of 77 million tons of total material of which some 200,000 tons is stockpiled ore. Diamond drilling has outlined an orebody 5900 ft long and 3400 ft wide containing an estimated 153 million tons of ore at 1.35% recoverable copper based on 80 % extraction.

Jan 11, 1969

By C. H. Loux

THIS paper deals primarily, with the advantages realized from the adoption of methods more suitable than those previously used. The improvements noted include: (1) modification of practice in shrinkage stoping, (2) use of sublevel caving over grizzlies, (3) improved haulage and loading, (4) use of contract wages wherever possible. The Washington mine is on Jonestown Hill, one mile south of Oxford, in northwestern New Jersey. It is producing 16,000 tons of concentrates a month, which are being shipped to the Alan Wood Steel Company&apos;s furnaces at Swedeland, Pennsylvania.

Jan 1, 1933

BENEFICIATION AND CONCEN&apos;TRATION; FROTH FLOTATION U.S. 4,069,144 - In the froth flotation beneficiation of phosphate rock using at least an acid flotation step and an amine flotation step, the crude ore is dried either during transport or storage or by air circulation immediately prior to classification, and the dried ore mixed with water and classified prior to flotation The preliminary drying substantially eliminates the usual problems with clay slimes G. C. Johnson and A. E. Schweizer, assigned to Mobil Oil Corp. Jan 17. 1978. 4 pp (209- 11) . Filed 1 1-19-75 (633,535).

Jan 1, 1979

The 116th (New York) Meeting of the Institute will be held in the third week of February, 1918. The Committee on Papers and Publications has set Dec. 1, 1917, as the closing date for the receipt of .manuscripts intended for this meeting. Manuscripts must be received by the Secretary on or before this date. If they are sent through members of the technical committees they must be sent to those committees enough in advance of the time to be forwarded and in the. hands of the Secretary by the time specified.

Jan 11, 1917

The 114th(New York) Meeting of the Institute will be held in the third week of February, 1917. The committee on Papers and Publications has set Dec. 1, 1916, as the closing date for the receipt of manuscripts intended for this meeting. . Manuscripts must be received by the Secretary on or before this date. If they are sent through members of the technical committees they must be sent to those committees enough in advance of the time to be forwarded and in the hands of the Secretary by the time specified.

Jan 10, 1916

By W. W. Anderson, S. Razi

Electroluminescetrce of single crystals of terbium-(loped ZnS prepared by vapor-transport technique shows the sharp line specirum characteristic of the 4f— 4ft,ansitiotzs of the trivalent Tb3 rotz. V-I tt~easuverr~ents give evidence of space-ellarge-lirrlited curvent but the thrveshold for trap-filled law behavior is not iu agreement with Lampert&apos;s theory for. Single injection. Variations of &apos;brightness with applied voltage, the observation of double peaks its brightness because joms, and the spatial distribution oi electroLur?zir~escerrce indicate that the accelet~atiotz-collision mechanism involving the bst lattice and/ov shallow traps is most likely to be responsible fov excitation of&apos; electrolnminescence. Efficiency rtreusuver)~etits show the quantwn efficiency to be about 10 pct and powev efficiency about 0.05 pct. Effect of anr~eallng the crystal in sulfur vapor is to enluztzce llle rare-earth emission. It rs pvoposed tlzat sulfitv anr~ealing crreates acceptorr-lvpe defects with which the donor-type vare-eavtll ion can associate more readily vesulting in enhanced rare-earth emission. A&apos;o such e~zlznr~cerr~etrt is obserued when the crystal is atztrealetl in zinc vapor. Photolianinescence of ZnS doped nith a variety of rare earths also shows tile slurvp l~rze rwve-eavtlz erriission which in sorrretirr~es accompanied by broad band, stvuctureless lattice emission. Photo-atrd electrolutr~itzesce?~ce of ZIIS:Tb slw~rj do!rlit~unt rare-earth emission in the ~ticirzity of 54(3OA corre-sporrdit~g to the transition D* — Fj. Hoz~!el)er, the detailed line structuve of the luo spectvtr is cliffevet~t, irzdicutit~g that different sites are active in the two processes. Decay of rave-eartlr fluorescence in ZnS doped with any of sei!evul vuve eurtlzs car1 be described by a single exporleritial e.scepl joy ZrlS:lIo. Tl~is exceptiotr can be explaitred it~ tevrr~s of tlre closely spaced er~evgy 1e1:els Jov the HO~&apos; iorr. Decay lime measurertzekzts jov ZnS:Tb, using pulsed elect,-ical ar~d pulsed opticcll excitutiorzs, (11-e itz goor1 agrcetrier~t. LUMINESCENCE of rare-earth-doped materials has been a subject of interest for the past 20 years. Within the past few years there has been a considerable increase in rare-earth research motivated in search of new and more efficient laser materials and also due to the use of certain-rare-earth compounds in the preparation of color television screens. The purpose of this study has been to seek an understanding of some of the basic processes involved in exciting the rare-earth luminescence which is associated with transitions within the 4f shell of the trivalent rare-earth ion. Single crystals of ZnS doped with a variety of rare-earth ions have been prepared by vapor-transport technique described elsewhere.&apos; Photoluminescence was excited by a high-pressure short-arc mercury lamp together with suitable glass and chemical filters. For electroluminescence, sinusoidal and pulse excitations were used. 1) ELECTRICAL CHARACTERISTICS 1.1) V-I Measurements. Electroluminescence experiments were performed on crystals of terbium-doped ZnS. The samples were cleaned and etched and indium or In-Ga alloy contacts were alloyed on by heating in H2 atmosphere to 600°C for times ranging up to 10 min. Static voltage-current measurements were made on several samples. Fig. 1 shows the results for a typical sample. For voltage V < 20 v, the V-I relationship is linear giving a resistivity of 2.5 x 109 ohm-cm for this particular sample at room temperature. In the range of 20 to 250 v, I varies as V "3 and at still higher voltages (when electroluminescence is visible to the scotopic eye) current varies as Vs up to 600 v, all at room temperature. At 77"K, for V > 200 v, / I vge5 up to 1000 v. The V-I characteristics at room temperature follow reasonably well the behavior predicted by Lampert&apos; for one carrier space-charge-limited current in an insulator with traps although, as shown later, the expression derived by Lampert2 for the threshold for trap-filled law behavior Vtfl yields an unrealistically low value for trap density if we use the experimental value of 300 v for VtfL. Assuming the case for shallow trapping, the transition from Ohm&apos;s law behavior to space-charge-limited behavior occurs at voltage Vtr given by where no = thermally generated free carrier density, L = length of the sample, e = static dielectric constant, 6 = ratio of free to trapped electron densities, e = electron charge. For the ZnS:Tb crystal, L = 0.5 mm, E = 8.3 €0, Vtr - 20 v, and no = 5 x 10&apos; per cu cm, calculated from the ohmic behavior assuming electron mobility of 100 sq cm per v-sec. This results in 9 = 0= As more and more electrons are injected the Fermi level moves up in the forbidden gap toward the conduction band. If we assume a single-energy level for traps (which is not strictly correct, as we will show later), the current voltage characteristic is profoundly affected when the Fermi level crosses the trap level. The traps are now filled and injected carriers can no longer be immobilized in traps. Hence, current rises sharply with voltage. The transition from space-charge-limited behavior to the trap-filled behavior occurs at voltage VTFL given by

Jan 1, 1968

By E. W. Johnson, M. L. Hill

Equilibrium concentrations of hydrogen in iron were measured at H2 pressures up to 136 atm and temperatures down to 145°C. Residual hydrogen was prominent near 600°C in air-melted but not in vacuum-melted iron. The diffusible hydrogen solubility is abnormally high below 390°C, confirming the hypothesis of hydrogen trapping.&apos; It appears that the traps for hydrogen in iron form suddenly on cooling. The estimated H2 pressure in equilibrium with 5 ppm hydrogen in steel at room temperature is less than 1000 atm. It was shown previously1 that the diffusivity of hydrogen in a-Fe below 200°C is anomalously low, a behavior attributed to the presence in the metal structure of hydrogen "traps." The energy of the trapped hydrogen was computed as 4.8 kcal Per g-atom below that of the interstitially dissolved hydrogen. The strongest confirmation of the trap hypothesis should be obtainable from measurements of the hydrogen solubility at low temperatures. such measurements have been performed and are reported in this paper. The "residual hydrogen" effect1&apos;&apos; must be carefully controlled if valid measurements of the solubility are to be obtained, and such an effort was made in the present work. Previous data for the solubility of hydrogen in iron have been summarized by Geller and Sun.3 Their equation for the most probable solubility at 1 atm in a-Fe above 400°C is

Jan 1, 1962