Search Documents

By M. D. Banus, M. B. Bever, A. K. Jena

The heals of formation at 78", 195, and 273°K of the ternary compound h3SbTe2 based on the elements and based on the binary compounds In Sb and [inTe have been measured. The heats of formation at these temperatlcres of the binary compounds In Sb and In Te based on the elements have also been determined. Heal contents and free energies of the three compounds have been calculated from 0° lo 80I)°K. The free energies of joyrrzalion, heats of formations, and entropies of formation at 298°K have also been calculated. The results shown that the tertnary compound is metastable with vespecl to InSh and ln Te below 696 °K. bul is slable above that temperature. The weaker bonding of results in a positice entropy of formation which with incrensirzg temperature makes increasing negative conlvihtclions to the free energy and above 696°K renders the compound slable. THE ternary compound In3SbTez occurring in the quasi-binary system In Sb- In Te' forms on cooling at 829°K by a peritectic reaction.' Observations at 673" and 573 K have shown that this ternary compound decomposes slowly into the binary compounds InSb and1n~e.l'' It has not been possible to analyze the metastable behavior of the ternary compound because up to the present time data on its thermodynamic properties have been lacking. Some information on the binary compounds, however, is available. The heat of formation of InTe at 273°K and its free energy at 673°K are kn~wn.~'~ The heats of formation of InSb at 78", 273', 298", and 723°K have been measured5-' and its heat capacity between approximately 12" and 300"Kg9l0 is also known. In the investigation reported here the heats of formation at 78% 195% and 273°K of the ternary compound In3SbTez have been measured. The heats of formation of the binary compounds InSb and InTe at these temperatures have been obtained by combining new calorimetric results with previously published data. The heat contents and free energies of the three compounds at various temperatures from 0" to 800°K have been calculated. Against the background of this information, the metastability of the ternary compound will be discussed. 1) EXPERIMENTAL 1.l) Preparation of Specimens. The materials used consisted of the elements indium, antimony, and tellurium, the binary compounds InSb and InTe, and the ternary compound In3SbTez. The elements, obtained from American Smelting and Refining Co., had a nominal purity of 99.999+ pct. The compound InSb was Cominco semiconductor grade; the compound InTe was prepared from the elements by melting under a vacuum of 10-h m Hg followed by slow cooling. Three batches of specimens of the compound In3SbTez were used. One batch was prepared by melting appropriate amounts of the elements in an evacuated and sealed Vycor tube. The melt was held at approximately 100°K above the liquidus for about 8 hr, shaken repeatedly, and quenched into a mixture of ice and water. The specimen was annealed in vacuum at 760°K for 4 weeks. In preparing a second batch, a mixture of the component elements was melted and quenched in water. The resulting ingot was powdered. The powder was pressed into pellets, which were annealed in vacuum at 748" to 773°K for 4 weeks. A third batch was prepared in the same manner as the second, except that the starting materials were InSb and InTe rather than the elements. Metallographic examination of samples of the three batches and X-ray diffraction examination of a sample of the second batch did not reveal evidence of microsegregation or a second phase. The results obtained with the three batches showed no systematic differences. 1.2) Calorimetry. The calorimetric method has been described in detail." Samples of the compound In3SbTez, mechanical mixtures of InSb and InTe in the proportion of 1:2, and mechanical mixtures of indium, antimony, and tellurium in the proportion of 3:1:2 were added to a bismuth-rich bath at 623°K in a metal-solution calorimeter. These additions were made from 78°K (liquid nitrogen), 195°K (dry ice and acetone), and 273°K (ice and water). The heat effects of the additions were measured. The difference in the heat effects of the additions of a compound and the additions of the mixtures of its constituents, adjusted for differences in the concentration of the bath, is the heat of formation of the compound. In the concentration range not exceeding 1.5 at. pct solute, the heat effect of the additions was a linear function of concentration. The heat of formation refers to the temperature from which the additions were made, namely, 78", 195", or 273°K. Several calibrating additions were made in each calorimetric run. The calculated heat capacity of the calorimeter and hence the calculated heat effects of the additions of samples depend upon the values adopted for the heat contents of the calibrating substance. In this investigation bismuth at 273°K was used and a value of 4.96 kcal per g-atom was taken for (HGZ3"k . 2) RESULTS AND DISCUSSION 2.l) Heats of Formation. The heats of formation of the ternary compound In~SbTez from the component elements indium, antimony, and tellurium and from

Jan 1, 1968

By C. E. Lesher

Low-TEMPERATURE carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus 3/8 -in- or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal, of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic con-sumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold.

Jan 1, 1940

By Robert Ammon

The purpose of this paper is to present a brief sketch of the development of this hindered-settling classifier, but primarily to show the actual results obtained in practice with the classifier working on the Butte copper ores at the Boston & Montana Concentrator at Great Falls and the Washoe Concentrator at Anaconda. The writer has endeavored to be as brief as possible, giving only the essential figures showing the efficiency of the classifier and leaving considerable interesting information to be derived by the reader from the statistics given. The paper deals with the practical work of the classifier under the following heads: 1. Desliming 4.0-mm. primary feed, overflow from 0.07 to 0.0 mm. 2. Desliming 1.25-mm. secondary feed, overflow from 0.07 to 0.0 mm. 3. Desliming Huntington Mill discharge, overflow from 0.07 to 0.0 mm. 4. Classifying 2.5-mm. deslimed secondary feed, overflow from 1.00 to 0.07 mm. 5. Classifying 2.5-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 6. Classifying 4.0-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 7. Classifying middling-tailing product from roughing tables, overflow coarse tailing. 8. Classifying 2.5mm. trommel undersize, not deslimed, overflow from 0.75 to 0.0 mm. 9. Remarks on the inner feed cone. In the following pages all overflows are given in quartz dimensions; i. e., by a 0.75-mm. overflow is meant an overflow whose maximum particle is a 0.75-mm. quartz grain. By the term "slime" is meant all material which will pass through a 200-mesh screen whose average opening is 0.07 mm. The development of the classifier was commenced in the fall of 1910,

Jan 1, 1914

By Robert Mehl

PART I. ORIENTATION RELATIONSHIPS IN OXIDE LAYERS Oriented overgrowths and intergrowths among both metallic and nonmetallic substances have been recognized and studied for well over a century. The work of Widmanstätten in 1808 on the geometrical struc-ture in meteorites, a structure known by his name, demonstrated that oriented intergrowths can occur in purely metallic systems. This fact led to much of the early microscopic study of alloys, contributing greatly to the advance of physical metallurgy. The problem has been attacked again in recent years in a comprehensive fashion, with the object of dis-covering what atomic movements may occur during phase changes in alloy systems. Much of this work has appeared in the A.I.M.E. TRANS-ACTIONS in a series of papers published by Mehl and coworkers beginning in 19311. Although many aspects of this general problem remain unsolved, it may be said that the orientation of a new phase forming by precipitation from solid solution or by transformation invariably bears, a unique relationship to the orientation of the phase from which it formed, and that similarity in atomic patterns on atomic planes in the two phases play an important part in determining the orientation relationship. Analogous orientation relationships exist in oriented intergrowths in nonmetallic systems-mineral or inorganic. In 1827 Haidinger2 dis-covered natural intergrowths of hematite and magnetite, and demon-strated that the rough form of the magnetite octahedrons was delineated by small crystals of hematite, of which the basal (00.1) planes lay parallel to the octahedral cleavage planes of the magnetite. The description of this orientation relationship was later completed by von Rath3, who showed that the edge (00-1):(10-1) in hematite lies normal to the [111]

Jan 1, 1937

Forty-three years ago a record for low cost was made at the Spanish mine, in Nevada county, California. In 22 days of September, 1887, there was mined 2796 tons of ore at a cost of 37.5 cents per ton, of which 32.4 cents was for labor and 5.1 cents for supplies. The mill treated this ore for 23 cents per ton, of which 12.3 cents was for labor and 10.7 cents for supplies. Thus the total operating cost was 60.5 cents per ton. The yield was $1.16 in gold per ton, leaving a profit of 56 cents per ton, or 48 per cent of the yield. The mine was an open-cut in a schist formation on a hillside and the work was done by Chinese laborers that were paid $1.40 per shift. The ore was soft, and could be ground effectively in four Hunting- ton mills, supplemented by silvered amalgamating plates.* The engineer in charge was F. W. Bradley, a student from the University of California. As has been indicated, the conditions were unusually favorable in respect of softness of ore, accessibility to the mill, metallurgic simplicity, with cheap labor and power, but even at that the results were so remark- able as to attract general attention, which, as might be expected, was magnified, for advertising purposes, by the manufacturers of the Huntington mill, the firm of Parke & Lacy, at San Francisco. The record made at the Spanish mine therefore found its way into many textbooks on mining published at that time. The editor of the 'Mining and Scientific Press'† (at that date, Charles G. Yale) evidently took a warm interest in. the

Jan 1, 1932

By G. S. Brooks

WITH the gradual depletion of the natural-gas pools of the Kansas district, together with the uncertainty of further cheap fuel developments, some. of the western zinc companies turned to the coal fields, attracted by their permanency and the 'success of the Matthiessen & Hegeler Co. and the Illinois Zinc Co. Being then confronted with the problem of using a relatively high-priced fuel, although the ultimate' supply was very great, the fuel economies of the kilns and furnaces became of far more importance, and the more modern equipments, as a result, embodied distinct gads in this phase of the business. In addition, there have been some pronounced advances in the actual making of gas from these coals. Increased efficiency in gas making has contributed its share to lowering costs and those plants located in the higher priced fuel districts have probably been obliged to study these economies somewhat more closely. Naturally, many beneficial changes have resulted in both practice and apparatus in these sections. On, certain western coals, for instance, the actual saving in fuel consumption has been 50 per cent. By this is meant that, where about 1.75 tons were burned to smelt 1 ton of oxidized ore, 0.7 to 0.9 ton is now required. While comparisons by W. R. Ingalls1 of fuel economies in smelting in this country and Germany before the war may, in general, be correct, they do not appear to-do justice to the more progressive. American practice. It is doubtful whether German plants were substantially bettering these fuel ratios. Data furnished by Bender and Frams do not afford records averaging less than 0.9 ton coal per ton ore on materials from 40 per cent. to 50 per cent. zinc.

Jan 9, 1919

By J. E. Hackford

In some research work carried out by the writer, certain results have been obtained which bear on the fundamental nature and origin of coal and the relationship between coal and petroleum. Without entering into a discussion of the details of the experiments, which were conducted on petroleum and derived bitumens, there are given here, by way of definition, some of the relations that the writer has established between certain classes of bitumens of petroliferous origin. Bitumen.—-A natural organic substance, gaseous, liquid, or solid, consisting of hydrocarbons and the oxy-or thionic derivatives of the same, or of a mixture of all three. Diaspha1tenes.—-Those portions of bitumens that are soluble in ether or carbon disulfide, but are insoluble in a mixture of equal parts of ether and alcohol. Diasphaltenes are produced by the oxidation or thionization of petroleum oils; they have, as the name indicates, twice the molecular weight of asphaltenes, into which they are converted when subjected to moderate temperature. For example, an artificially produced diasphaltene, which was readily soluble in pentane and ether, was quite insoluble in either of these solvents after heating for three weeks at a temperature of 100" C., and was converted into an insoluble asphaltene. Aspha1tenes.—Those portions of bitumen that are insoluble in ether or ether alcohol but are soluble in carbon disulfide. Aspha1tites.—Those solid or semisolid natural bitumens that are composed, for the most part, of asphaltenes or diasphaltenes. A pure asphaltitel would be composed wholly of asphaltenes and diasphaltenes, but most asphaltites contain small percentages of oil and wax, which have not yet been converted into asphaltenes; they may also contain A small percent.age of kerotenes, which represent the next stage of the metamorphosis of asphaltenes. Among the naturally occurring oxyasphaltites may be mentioned grahamite; and among the thioasphaltites, gilsonite.

Jan 1, 1921

By Robert Ammon

THE purpose of this paper is to present a brief sketch of the development of this hindered-settling classifier, but primarily to show the actual results obtained in practice with the classifier working on the Butte copper ores at the Boston & Montana Concentrator, at Great Falls and the Washoe Concentrator at Anaconda. The writer has endeavored to be as brief as possible, giving only the essential figures showing the efficiency of the classifier and leaving considerable interesting information to be derived by the reader from the statistics given. The paper deals with the practical work of the classifier under the following heads: 1. Desliming 4.0-mm. primary feed, overflow from 0.07 to 0.0 mm. 2. Desliming 1.25-mm. secondary feed, overflow from 0.07 to 0.0 nun. 3. Desliming Huntington Mill discharge, overflow from 0.07 to 0.0 mm. 4. Classifying 2.5-mm. deslimed secondary feed, overflow from 1.00 to 0.07 mm. 5. Classifying 2.5-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 6. Classifying 4.0-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 7. Classifying middling-tailing product from roughing tables, overflow coarse tailing. 8. Classifying 2.5-mm. trommel undersize, not deslimed, overflow from 0.75 to 0.0mm. 9. Remarks on the inner feel cone. In the following pages all overflows, are given in quartz dimensions; i.e., by a 0.75-mm. overflow 'is meant an overflow whose maximum particle is a 0.75-mm. quartz grain. By the term "slime" is meant all material which will pass through a 200-mesh screen whose average opening is 0.07 mm.

Jan 8, 1913

By Robert Pike

THE first authentic description of an iron bath for the deposition of iron is probably that of Bottger in 1846, who used a bath containing ferrous sulfate and ammonium chloride. In 1861, Kramer deposited iron from ferrous chloride solution. Electrolytic iron was produced in 1.869 by Bietz, who used it for making some magnetic tests. In the same year, Klein is said to have worked out his process. Jacobi1 in 1869 described the results obtained in electroplating with iron on copper for making dies and plates for bank notes, by Klein's process. A letter from Klein to Jacobi describes the bath more fully. It consisted of FeSO4 + (NH4)2S04. Lenz2 described ?some properties of electrolytically precipitated iron. He used Klein's bath, FeSO4 + MgSO4 + MgCO3, to neutralize and obtained fine-grained and hard iron. His conclusions were as follows: 1. Electrolytic iron and copper contain gases, notably hydrogen. 2. The volume of gas absorbed by iron varies within wide limits, but it is easy for iron to take up very considerable quantities of gas. 3. The absorption of gas is principally in the first formed layers of iron. 4. When iron is heated, gas begins to come off below 100°, principally hydrogen. 5. Heated to redness, reduced iron oxidizes in water, in part at least at the expense of the oxygen of the water, decomposing it and setting free hydrogen, which is partly or wholly absorbed. Siemens,3 in 1889, was the first to propose a general process embodying a step for leaching a sulfide mineral with ferric chloride or sulfate and a step for regenerating the leach and depositing iron on a cathode in a diaphragm cell. So far as is known, Siemens did not carry out his patent

Jan 1, 1930

By Richard D. Harvey, Arthur M. Squires, Robert A. Graff, George Kan

Particles of half-calcined dolomite (CaC03 + MgO) that had undergone cyclic absorption of H2S and regeneration with C02 in laboratory tests reveal enlargement of the crystallite grain structure, reduction in the number of pores but enlargement in their size, and partial development of a relatively dense mosaic microstructure on outer surfaces of cyclically reacted particles. Scanning electron microscopy, X-ray microanalysis, microprobe analysis, and X-ray diffraction techniques were used to evaluate microstructural properties of particles after tests conducted at pressures of 1 and 21 atm and temperatures of 7000 to 9000 C. The tests conducted at 7500 C and 21 atm showed the most favorable absorption and regeneration capacities of the dolomite tested. The changes in structure and pores play a major role in reducing the sulfur reactivity of half-calcined dolomite particles. The mosaic microstructure forms more rapidly at 1 atm than at 21 atm pressure. Once it occurs it seals the surface of the natural pore channels that existed in the half-calcined dolomite and restricts further conversion of crystallites of CaCO3 within the particles. Although a relatively coarse, granular mosaic of crystallites is present on some particles cycled at 21 atm pressure after only three absorption-regeneration cycles, it does not completely cover the particles, and that is true even after 30 cycles. Individual crystallites of MgO were not resolved by the X-ray microanalysis, but we believe that during the tests the MgO occurs as crystallites no more than 0.1 um in diameter that are homogeneously distributed through the particles, and it remains essentially inert during the reactions. The MgO contributes to the maintenance of the original fine-grained and microporous structure of the particles, an effect that is most advantageous to absorption and regeneration.

Jan 1, 1976

By J. A. Bartnik, Gerald D. Rose, William H. Benson

New techniques in the magnetite and heavy media beneficiation industries demand more efficient magnetic dispersion and flocculation of the finely ground particles. Demagnetizing coils must produce several major effects, such as improving classification and screening efficiency, decreasing moisture content in filter cake and improving separation selectivity and green pellet properties. Likewise, magnetic flocculators must increase filtering rates and the settling rates of solids, improve magnetite recovery and produce cleaner water. To improve the design of equipment and to conduct tests leading to the optimization of such dispersion and flocculation, a program was initiated at Eriez Magnetics. The major conclusions reached are: 1. Laboratory and plant scale tests conducted on magnetite products show that a demagnetizing force of 450 rms oersteds at 60 cycles for 1/20- second duration will depolarize natural magnetite particles coarser than approximately 10 microns. This has been found satisfactory for most applications. 2. Effective flocculation of magnetite was obtained when a slurry with more than one percent magnetite was exposed for a period of approximately 1/15 second to a 600-gauss field. 3. The cost of demagnetizers (or flocculators) increases rapidly for larger diameter pipes. In order to reduce the cost, narrow rectangular sections are recommended for magnetic flocculators. 4. For minimum operating cost, permanent magnetic flocculators are ideal, chiefly because they do not require any maintenance and have no operating cost. 5. A newly designed electro-demagnetizing coil with high heat dissipation and a nonmetallic core provides high efficiency and long life. 6. To select the correct magnetic flocculator (or demagnetizing coil) the following information is necessary: a. Magnetic product susceptibility b. Magnetic product coercive force c. Percent of magnetic product d. Flow rate e. Viscosity f. Structure of magnetic product

Jan 8, 1968

By Bartlett W. Paulding

Since its introduction to the petroleum industry in 1949 by Clark,1 hydraulic fracturing or "hydrafracing" has developed into a widely respected and useful technique for increasing production from petroleum reservoirs. Even then, Clark described production increases of from 6 to 100 barrels of oil per day (bopd). Since that time, others have described treatments in which production increased from 12 to 456 bopd, from only a show to 40 bopd;2 from 48 to 219 bopd; 3 from 500 to 1400 bopd and from a show to 192 bopd.4 Although representative of only a few of many successful hydraulic fracturing operational6 these increases in production attest to the past and potential value of the hydrafracing technique to the petroleum industry. The technique has received a considerable amount of theoretical and experimental attention.1, 5-20 Unfortunately, however, the degree of general understanding of the mechanics of hydraulic fracturing is still inadequate to solve many recurring problems. The practicing engineer is plagued with difficulties in predicting such factors as: (1) the required pressure and viscosity of the fracturing fluid to not only induce the fracture but to control the extent of its growth, (2) the strength characteristics and amount of proppant to include in the fluid so that the fracture is held open once the fluid pressure is decreased, and (3) the volume of the reservoir influenced by the induced fractures and the resulting increase in production. A major cause of these difficulties is the uncertainty associated with determining the orientation of the hydraulically induced fractures. One's natural conclusion in considering the problem is that the orientation of the fracture would depend on several variables, as, for example, the relationship between the viscosity and injection rate of the fluid and the

Jan 1, 1968

By Wilson B. Emery

The discovery well in the Rock River field, in Carbon County, Wyoming, came in May 1, 1918. The field is on a large anticline having more than 1500 ft. of closure and production is obtained from three sands of the Dakota group. At its peak, production approximated 10,000 bbl. daily and is now averaging 2200 bbl. Total production to Jan. 1, 1930, exceeded 12,500,000 barrels. So far as known to the writer, Rock River was the first light oil field in the Rocky Mountain region to be produced under what we now term unit operation. Though this type of operation was not popularly acclaimed by the oil industry, the Federal Government and the public until many years after the inception of development at Rock River, the officials of the Ohio Oil Co. when acquiring this property were fully cognizant of the economies to be effected by unit ownership and the consequent elimination of competitive drilling and producing of wells, and had this in mind at the time. Thus unit management was introduced in this field at an early date by this company. Area and Management Fig. 1 shows the location of all wells drilled on the Rock River structure and the outline of the productive area as now defined, which amounts to 1380 acres. The hachured line indicates the area now under unit ownership; originally a much larger area was so owned but leases have been canceled as progressive development indicated their lack of oil. The management and operation of the entire productive area is handled by the Ohio Oil Co., which owns the majority working interest. The Continental Oil Co. with a 20 to 35 per cent. interest in much of this acreage, and smaller interests owned by others in some of the leases, constitute the remainder of the ownership. The fee rests in the State of

Jan 1, 1930

By AIME AIME

THE quarters provided for the session on Milling Methods, Monday afternoon, Feb. 17, were filled to capacity. Galen H. Clevenger presided and notables, such as A. W. Fahrenwald, A. O. Gates, F. A. Thomson, W. L. Zeigler and others who had not graced a milling meeting in New York in recent years, or per- haps even never before, were actually present and spoke "in person." The first paper, by A. W. Fahrellwald (T. P. 275), entitled "Classifier Efficiency ; An experimental Study," was summarized by the author, who clearly showed the inconsistency of determining the efficiency of a classifier by means of sizing tests, especially where the material classified consists of a mixture of minerals of different specific gravities. In place of sieve analysis the procedure recommended involves the use of a glass settling-tube which is considered to give ideal classification and thus serve as a standard against which mill classification will be compared and relative efficiency calculated. This procedure sounds logical. Perhaps the greatest difficulty may lie in securing an ideal classifier acceptable to every one.

Jan 1, 1930

By J. C. Danko, R. D. Stout, A. H. Holtzman

The deformation characteristics of pearlite have been studied by light and electron microscopy.1,2 In the electron-microscopic work, deformation was found to take place by 1) ferrite slip which is parallel to the lamellae, 2) slip transverse to the lamellae with both cementite and ferrite deforming, and 3) ferrite-cementite interfacial slip. The transverse slip gives a step-like appearance to the lamellae in light microscopic work. It was thought that spheroidization of deformed pearlite would commence at the regions of maximum cementite deformation, the "stepped" areas. Although there is no possibility for seeing slip in the microstructure if the specimen is polished after deformation, the step-like appearance of the lamellae clearly indicates the transverse deformation. Thus, the areas of cementite deformation are apparent after polishing and the effect of deformed areas on spheroidization may be studied by the usual metallographic techniques. This note reports the result of a metallographic investigation which substantiates that spheroidization begins in the "stepped" areas. An AISI 1080 steel was normalized, re-austeni-tized at 1040°C, and isothermally transformed at 700 ± 4°C for 4 hr. Cubes, 5 mm to a side, were compressed between parallel plates to strains of 20, 40, and 50 pct. After deformation, specimens were heated to 600, 650, and 700°C; withdrawn at increasing time intervals and examined metallo-graphically for the percentage and distribution of spheroidite. The percentage of spheroidite was determined by lineal analysis. A micro structural region considered as spheroidized was one in which a lamellar skeleton was not distinguishable. Table I gives the times necessary for 95 pct spheroidization for each condition of strain and annealing temperature. Fig. 1 shows the microstructure of coarse pearlite compressed 20 pct, then polished and etched. Here the lamellae form a step by bending at two

Jan 1, 1959

By Frank Firmstone

In the summer of 1842 my father, William Firmstone, was engaged by Charles Jackson, Jr., of Boston, to examine the conditions in the Lehigh valley as a site for blast-furnaces using anthracite for fuel. In consequence of his report, he was further engaged by Mr. Jackson to build a furnace for him and his partners on the Lehigh canal, 2 miles above the mouth of the river at Easton. Work was begun in the fall of 1842, and the first furnace blown-in in 1844. The history of the works, therefore, from 1844 to 1887, when my own connection with them ceased, covers only four years less than the whole period of the rise, culmination, and commencement of the decline in the smelting of iron with anthracite in America, the beginning of which, in a commercial sense, may be put in 1839.' Although this paper, as the title indicates, is concerned almost exclusively with the furnaces at Glendon, still what was done there was more or less influenced by current opinion in the district, and even reflects, to some extent, the changes in opinion and practice with mineral fuel the world over. No. 1 Furnace was built of red brick, on four piers, had three tuyeres and fore-hearth and tymp, as was universal with furnaces using mineral fuel until the introduction of Lurmann's cinder-tuyere. The dimensions and profile are shown in Figs. 1 and 2. The first hearth (Fig. 1) was of sandstone; all after were of fire-brick (Fig. 2). The profile was no doubt derived directly from Gibbons's furnace,2 for it appears from W. Firmstone's note-books that in October, 1840, he visited " Gibbons' new furnaces building at Corbyn Hall," and I have an old drawing,

Jan 1, 1910

By K. A. Johnson, F. H. Ellinger, C. C. Land

The Pu-La alloy systenz has been studied by thertnal, tnzcrographic, and X-ray diffraction methods. It is churacterized by a liquid miscibility gap, a maximum solubility of about 20 ut. pct PM in y lanthunum and 19 at. pct PI* in 0 lanthanum, very little soluibility of lanthanum in the plulonium allotropes, and the absence of intermediate phases. THE existence of immiscible liquids in the Pu-La system has been reported by Schonfeld.1 A tentative phase diagram based on the results of thermal-analysis experiments has been constructed by Poole et a1 2 This diagram shows a liquid immiscibility loop with a monotectic at 77 at. pct La and 846°C. 7 lanthanum is shown to dissolve 20 at. pct Pu and to decompose by an inverse peritectic reaction (y La = L , + p La) at about 82 at, pct La and 833°C. The ß lanthanum solvus was not determined, but the thermal work indicated a maximum solubility of 16 at. pct Pu in ß lanthanum. The present investigation has defined the solubility limits of plutonium in y lanthanum and 0 lanthanum, and, with the exception of minor discrepancies, has verified the results of Poole et al. 1) EXPERIMENTAL The electrolytic plutonium melting stocks were better than 99.9 wt pct pure, the main impurities being 90 ppm Fe and 50 ppm W. The lanthanum melting stocks, supplied by Research Chemicals and the Cerium Metals Corp., were about 99 wt pct pure, the main impurity detected by our spectrochemical analysis being 2000 ppm Fe. The components for each alloy button (-5 g) were weighed on an analytical balance and were melted together in a conventional arc furnace. If no significant weight loss occurred during melting, the as-weighed

Jan 1, 1968

[This paper was presented for the author, who is now in the National service, by H. M. Chance, and was illustrated by a working model built to the plans shown in the Bulletin, for February, 1918, p. 268. For more convenient operation, a small motor-driven centrifugal pump was attached to the overflow outlet (5, Fig. 1, p. 267) delivering to the inlet, 4. The pressure of ingoing water was then adjusted by a valve at 4, and was indicated by the column of water in a vertical glass tube connecting with the pressure chamber; an average pressure of 15 in. of water column was maintained during the demonstration. The sand used in the test was beach sand, which had simply been passed through a 20-mesh screen; about 45 per cent. was finer than 80 mesh. The circulation of water was at the rate of about 5 gal. per square foot per minute, and the rising velocity of the water in the box as a whole (not the velocity of the jets) was 6 in. per minute. At this consistency, the specific gravity of the fluid mass was between 1.55 and 1.60. Mr. Chance estimated that it would be possible to maintain a fluid mass of this consistency, 3 ft. deep, and with an area of 50 by 60 ft. with an expenditure of 15-hp. Mr. Chance then showed how a lump of coal would float on the fluid mass, and also made a separation of slate from coal on a small scale in a wire cage submerged momentarily in the fluid. The following demonstration relates to a matter not contained in the original paper, and was presented as of interest to the operators of cyanide and other lixiviation processes dealing with fluid mixtures of varying specific gravity.-Ed.]

Jan 4, 1918

By Gail F. Moulton

The production of petroleum in Illinois in 1928 was approximately 6,500,000 bbl., a decline of about 500,000 bbl. from the previous year and of about 1,500,000 bbl. from 1924. Production increased about 200,000 bbl. in Indiana to slightly less than 1,000,000 bbl. Production for 1929 is estimated at approximately 6,000,000 bbl. for Illinois and 1,000,000 bbl. for Indiana. Illinois Because production from most of the wells in the state has declined to a small daily average and the low prices for crude oil discouraged wildcatting, the number of wells drilled fell below that for any previous year since the development of commercially important production in the state. The Ohio Oil Co. discovered a pool of apparent commercial importance in southwestern Illinois near Dupo, in St. Clair County, and favorable showings of oil were encountered in a well in southeastern Illinois, near Harrisburg in Saline County. New production from the Dupo area is expected to check the rate of decline for the state. Thc following tablel summarizes field developments for 1927 and 1928 (for important detail by counties see notes at foot of table): 1027 1928 Completions........................................... 162 145a Initial production, bbl.................................. 2244 1840b Dry holes........................................,.... 66 58" Gas well completions................................... 13 8d 0111 wells abandoned.................................... 45" a Crawford, 44; Lawrence, 28; Wabash, 40. b Crawford, 501; Lawrence, 403; St. Clair, 165 (4 completions); Wahash, 668. o Crawford, 12; Wabash, 19. d Crawford, 6. b Lawrence, 21; Wabash, 15. The discovery well in the Dupo field in St. Clair County, produced about 150 bbl. per day from the Trenton lime at 660 ft. It is located in a northern extension of the Columbia-Waterloo anticline on which the Waterloo pool was developed in 1921. The best information on the.

Jan 1, 1929

By D. W. Fuerstenau

Measurement of zeta potentials is a useful tool to study the surface chemistry of minerals under flotation conditions. Because there is continued interest in this approach, the apparatus for obtaining zeta potentials of nonconducting solids by the streaming potential method is outlined here. Fig. 1 illustrates the streaming potential apparatus. The streaming potential cell or plug consists of two 24/40 standard ground joints (4) joined with a piece of pyrex tubing 60 mm long and 12 mm in diam (5). The electrodes are made of bright platinum disks 19 mm in diam and 1 mm thick through which 0.5-mm holes have been drilled (6). To the surface of each is welded a piece of 80-mesh platinum gauze. Each electrode is permanently mounted on the ends of the inner parts of the two standard joints by means of a platinum wire (7) which connects it to the tungsten seal at the end of the cell (8). For ease in cleaning and handling the apparatus, the streaming cell is fastened to the 500-ml reservoir flasks (1) by means of two 18/9 ball and socket joints (2). This particular arrangement permits passage of the solution in either direction through the plug of particles. Flow of solution can be stopped by a stopcock (3). One of the reservoir flasks has a large opening to permit insertion of either a thermometer or a pair of electrodes for measuring pH of solutions within the system. In making the experiments, the plug is filled with 48 to 65-mesh particles, but a layer of 28 to 35-mesh particles is placed at each electrode to prevent any of the finer particles from passing through holes in the electrodes.

Aug 1, 1956