Search Documents

By Harlod Washburn, Herbert Hoover

This paper is in the nature of a rough preliminary report on the progress that has been made in the application of the mass spectrometer to various problems arising in the petroleum industry. A few years ago the authors considered a number of the problems that were arising in the qualitative and quantitative measurement of small amounts of hydrocarbons. The methods available of making analyses by chemical techniques appeared to leave much room for improvement. Without going into the reasons at this point, attention was turned to the possibility of employing physical instead of chemical methods of accomplishing the desired results. A preliminary investigation disclosed that the mass spectrometer presented a possibility of solving many problems which could not easily be accomplished by other methods. Work was begun in developing the necessary apparatus and technique. A great deal of encouragement and many valuable suggestions were received from Dr. Robert A. Millikan, Dr. W. R. Smythe, and Dr. W. N. Lacey, of the California Institute of Technology, and from Dr. E. 0. Lawrence, who recently received the Nobel Prize, of the University of California. The authors particularly wish to acknowledge the very great willingness of these outstanding scientists to be helpful in solving many of the problems that were involved. So far as the authors are aware, this was the first application of the mass spectrometer to commercial work. The results were considerably better than had at first been anticipated. Briefly, it is possible to run a qualitative and quantitative analysis of an unknown mixture of hydrocarbon gases, with an accuracy of better than plus or minus 5 per cent of each of the various constituents. An exceedingly high degree of sensitivity has been obtained, and a relatively short time is required to complete an analysis. Furthermore, it is unnecessary to separate a mixture of gases into its various components in order to complete the analysis. The Mass Spectrometer The mass spectrometer should not be confused in any way with the optical 01 grating type of spectrograph now in general use. The operation of the mass spectrometer is entirely different in principle and bears practically no resemblance to the optical or grating instruments. The original conception and development of the mass spectrometer dates from and is generally credited to Aston, of Cambridge, England. An early accomplishment of his research, about 20 years ago, was the discovery that the inert gas neon was actually a mixture of two kinds of atoms, one of the atomic weight 20 and the other of atomic weight 22. These two components occurred mixed in such proportion as to yield the usual atomic weight of 20.2. The study was continued and most of the elements were shown to be mixtures of components whose atomic weights can, to in

Jan 1, 1941

By H. Gisser

Recent experimental work has demonstrated (1)2 that ammonia and oxides of nitrogen are formed during the aging of smokeless powder. This is significant in connection with the problem of "season cracking," or stress corrosion of brass cartridge cases in view of other work(1) indicating that stressed and "stress- relieved" cases stored with small quantities of added ammonium nitrate crack on firing. The deterioration of stressed brass by ammonia has been known for some time(z) and it appears therefore that stress- corrosion cracking of brass cartridge cases is intimately associated with the so-called "powder volatiles," ammonia and oxides of nitrogen, both of which are decomposition products of smokeless powder. Working on the hypothesis that any barrier which prevents the powder volatiles from reaching the brass surface will reduce the incidence of stress-corrosion cracking, it was considered desirable to investigate the use of organic resin films to accomplish this purpose. The possibility of formation of ammonia within the nitrocellulose powder charge and by reduction of nitrogen oxides on the surface of the brass case requires that the barrier film be resistant both to ammonia and oxides of nitrogen. The film must also be impermeable to ammonium salts, either solid or in solution, since these salts and water necessarily appear within the powder charge. The usefulness of the

Jan 1, 1945

By Carl Gatlin, S. Srini-Vasan

It is shown thar k k ratios cornputed on the as.sutnption that the average sandstone reservoir has a pore-size distribution characrerized by a linear 1/P saturatioN plo are in good agreewient with correspotlding k,,/k,, ratios obfairzed by Wahl, Mul-/ins and Elfrink by correlatiotz of field measurements. Methods of calculating relative permeability data have recently been reviewed and extended.' It was shown that for sandstone reservoirs where ' is approximately a linear function of effective saturation (as suggested first by Corey') it is possible to express relative permeabilities in very simple terms. For systems wetted by connate water and producing oil and gas (gas saturation growing at the expense of oil) the expression for the The accuracy of Eq. I has been frequently confirmed in our laboratories; because of its simplicity we make routine use of it in the analytical solution of proble~ns in reservoir engineering. Nevertheless, comparisons of the k,,,/k,, ratios yielded by Eq. 1 with appropriate reservoir data have been few. The publica- tion by Wahl, Mullins and ElfrinkV of an empirical equation for k,,/k,, ratios is thus of interest since this equation is specificalljl stated to be Vased on the correlation of field measurements made on sandstone reservoirs. Not surprisingly these authors found that it was necessary to

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The a-p type alloys are subject to a loss of tensile ductility with increasing hydrogen content. No hydride phase is visible in embrittled a-B type alloys. The embrittlement encountered appeared to be of the strain-aging type. Both compositional and structural factors are shown to influence the hydrogen tolerance of a-B type alloys. IN previous papers by the authors, the effects of hydrogen on the structure and mechanical properties of high-purity and commercial-purity titanium were described. It was shown that the presence of hydrogen in these materials results in a hydride phase having low solubility at room temperature. This insoluble phase had little effect on the room temperature tensile properties, but did decrease the notch-bar toughness to a large degree. The binary Ti-H systemz indicates that hydrogen is much more soluble in £ than in a-titanium. Hence, it is not expected that the embrittling effects of hydrogen in a-fi alloys will be similar to that found in a alloys. Materials of this type studied in the present investigation included two commercial a-/3 alloys, Ti-8Mn and Ti-4A1-4Mn; three high-purity Ti-Mn alloys containing 3, 6, and 9 pct Mn; and four high-purity Ti-Mo alloys, Ti-SMo, Ti-10.9M0, Ti-13.1 M0, and Ti-20M0, of the a-B and B types. Materials and Fabrication—The high-purity base alloys, composed of iodide titanium and high-purity metals, were prepared by double arc melting under argon in a water-cooled copper crucible, using a water-cooled tungsten electrode. Radiographic examination showed homogeneous Ti-Mo alloys. The analyses of the alloys used in this investigation and their as-fabricated hydrogen content, where determined, are listed in Table I. The two commercial alloys were 1/2 and % in. diam bar stock. No analyses other than hydrogen content were made. In order to maintain the a-B relationship existing in the two commercial alloys, vacuum annealing and hydrogenation were carried out in the B field prior to final fabrication. Fabrication then was done by The three high-purity Ti-Mn alloys were forged to 3/4 in. diam rods at 1600°F, and hot swaged to 1/2 in. diam at 1380°F. Machined and degreased bar stock was vacuum annealed or hydrogenated, fabricated to 1/8 in. diam rod by hot swaging, annealed in argon for 1 hr at 1380°F !75O°C), and water quenched. The six yz lb Ti-Mo ingots were forged to Wi in. diam rods at 1600°F and then hot swaged to % in. diam. Machined and degreased specimens were vacuum annealed or hydrogenated in the /3 field, prior to fabrication, by swaging to Y4 in. rod at 1400°F. After fabrication, the 5 and 10.9 pct Mo alloys were annealed in argon for 16 hr at 1290°F and water quenched to give equiaxed a-B structures. The higher molybdenum content alloys were argon annealed 4 hr at 1470°F and water quenched to give all £ structures.

Jan 1, 1957

By L. D. Jaffe

IN 1945-1946, the author measured temper brittle-ness in ingots of varying composition prepared by remelting SAE 3135 bar stock under vacuum. Since other investigators1-" have been referring to this hitherto unpublished work, belated publication seems worthwhile. Steel in 7 lb batches&apos; was induction melted with nickel additions in a magnesia crucible under a pressure of 10 microns of Hg or less and cast into a 2 in. diam chill mold. The compositions of ingots A, B, and C prepared in this way are shown in Table I; the vacuum melting lowered carbon, manganese, sulphur, and nitrogen content. Ingot B was homogenized 24 hr at 1095°C; ingots A and C were not homogenized. Blanks, M in. square, were cut from each ingot, austenitized 1 hr at 870°C, water quenched, tempered 1 hr at 595"C, and water quenched. Half the blanks from each ingot were given an embrittling treatment of 50 hr at 455°C and water quenched. A few specimens, embrittled and unembrittled, were finally heated 1 hr at 580°C and water quenched. Charpy specimens machined from the blanks were V-notched on the side closest to ingot mid-radius and paired as to radial position in the ingot, one of each pair having received the embrittling treatment and the other not. Specimens were broken in a standard impact machine at various temperatures, the same temperature, in general, being used for both bars of a pair. Fig. 1 shows the results. It is evident that temper brittleness, as measured by the increase in temperature of transition from brittle to tough failure introduced by the 455°C treatment, was decreased but not eliminated by reducing carbon to 0.006 pct, manganese to < 0.004 pct, and nitrogen to 0.001 pct. In another study," temper brittleness was apparently eliminated by -reducing carbon to 0.003 pct, with 0.80 pct Mn and 0.0015 pct N (ingot D)." • Analyses given for carbon below 0.02 pct were made by Jensen method; for nitrogen, by Kjehldahl method. Values quoted else-where&apos;-&apos;." for carbon content of ingot C and for nitrogen content of ingot D were obtained by conventional combustlon and by vacuum fusion methods, respectively, and are considered much less accurate. The 580°C final treatment removed previous em-brittlement (ingot B particularly), indicating that this was "reversible embrittlement."" Metallographic examination of ingot C with 1 pct nital etch revealed only ferrite; ingot A had carbide spheroids uniformly distributed in a ferrite matrix. With ethereal picric acid plus zephiran chloride etchant.&apos; no differences between embrittled and un- embrittled specimens of ingots A, B, or C were noted. Fracture of C and D below the transition temperature was predominantly transcrystalline, with traces of intercrystalline, in both embrittled and unembrittled conditions. The corresponding fracture of unembrittled B was mixed transcrystalline and intercrystalline; of embrittled B, predominantly intercrystalline with some transcrystalline areas. . . . Acknowledgment The efforts of J. C. Leschen, formerly of National Research CO~P., in preparing the ingots are acknowledged with thanks.

Jan 1, 1956

By E. Maxwell, C. J. Bechtoldt, H. C. Vacher

IN the course of an investigation of the properties of metals at low temperature there was occasion to determine the constitution of four iridium-osmium alloys. There is very little information in the literature1 on the constitution of synthetic Ir-0s alloys. Zvyagintzev&apos; s has made a comprehensive study of different natural Ir-0s alloys and concludes that alloys containing more than 32 pct 0s have the close-packed hexagonal structure of osmium, whereas those containing less than 32 pct 0s have the face-centered cubic structure of iridium. The alloys studied in this work were prepared by the American Platinum Works, Newark, N. J., and were received in the form of fragments approximately 1.5 mm average diameter. The fragments had been obtained by crushing ingots made by fusing charges of iridium and osmium under an arc and air cooling. The ingots were not given a homogenizing heat treatment. Sample fragments Table I. Results of X-Roy Diffraction and Microscopic Examinations Phases Present as Determined by X-ray Diffraction Osmium Alloy Close- Iridium Face- Packed Centered Osmium, Iridium, Hexagonal Cubic Mlcro- WtPot Wt Pct Structure Structure scope 0 99.9 None Present 1 23.6 76.4 None Present 1 38.7 61.3 Present Present 2 59.4 40.6 Present Present 2 79.0 21.0 Present Not detected 2 99.9 0 Present None 1 Note: Chemical analyses of the iridium, osmium, and alloys were furnished by the American Platinum Works. of the iridium and osmium used in making the alloys also were included. Several fragments of each metal and alloy were examined microscopically and by X-ray diffraction. For the X-ray method the fragments were crushed further to pass a 270-mesh screen, then sealed in evacuated fused-silica tubes, heated to 1100°C for 18 hr, and allowed to cool in the furnace. Powder X-ray diffraction patterns were obtained from the annealed fragments by means of a Norelco camera having a diameter of 114 mm, and unfiltered cobaIt radiation. For the microscopic examination several fragments in the as-received condition were mounted in Melmac, (American Cyanamid Co.) and ground using the conventional series of abrasive papers. The polishing was done with 0-2 diamond abrasive on a Microcloth (Buehler Ltd.) lap, wet with xylene. After polishing, the surface was etched electrolytically in a 10 pct solution of chromic acid or in a 10 pct solution of potassium cyanide. Both reagents attacked the osmium-rich constituent, whereas the iridium constituent was attacked slightly by the chromic acid reagent and not noticeably by the potassium cyanide reagent. The results of the X-ray diffraction and microscopic examinations are summarized in Table I. Fig. 1 shows the microstructure of a 21 pct Ir-79 pct 0s alloy. The results indicate an appreciable solid-solu-bility range of osmium in iridium as was reported by Zvyagintzev.&apos; The solid-solubility range of iridium in osmium is more restricted, apparently less than 21 pct Ir. This implies a large range of composition in which two phases can coexist that was not reported by Zvyagintzev.

Jan 1, 1955

By A. W. Fahrenwald

THE absolute efficiency of crushing and grinding in a ball mill is not known. A number of investigators have made calculations to this end and have presented efficiency figures. Two factors have prompted further investigation of this subject: (1) the unbelievably low magnitude of the values offered, and (2) a desire to obtain, if possible, true relationships between the relative efficiencies of a ball mill operating under varying conditions. A useful forward step in the study of mill efficiency was made when Martin1 and Gross and Zimmerley2 proved the correctness of Rittinger&apos;s law, and incidentally the incorrectness of the so-called Kick law, and when Gross and Zimmerley3 determined and gave surface values for Tyler sieve-sized quartz. These data are probably accurate throughout the range of the sieve scale, but on -400 mesh (which is the finest sieve available), the surface data, as obtained by the hydrofluoric acid disso-lution method, are of doubtful reliability. Any inaccuracy existing in surface determinations of -400-mesh material, especially when comparing runs in which varying quantities of this product are formed, will cause the resulting relative mill efficiency values to be distorted. Moreover, knowing surface accurately, the efficiency calculations require a surface energy figure. Two such figures are to be found in literature, one by Edser4 and one by Martin.5 Edser&apos;s surface energy

Jan 1, 1931

By M. J. Duggin

Evidence is produced below to show that the carbide "Mn,C," reported by Kw,and ersson&apos; is really a mixture of two carbides. One is an Fe-Mn carbide which is probably isomorphous with hexagonal Mn15C4, reported by Bouchand and Pruchart.&apos; The othev is a tetragonul Fe-Mn carbide with cell dzmensions close to those reported previously by the author3 for an Fe0.1Mno. carbide. IN a recent investigation several Fe-Mn carbide specimens, each weighing about 5 g, were prepared in a manner previously reported.3 Debye-Scherrer X-ray photographs were taken of at least two samples from different parts of each specimen using a 114.6-mm-diam camera. The exposure time was 2 hr using filtered chromium radiation, a tube voltage of 35 kv and a tube current of 10 ma. In the case of one specimen, which contained nominal weight percentages of iron, manganese, and carbon of 9.40, 84. 6,, and 6.0, respectively, duplicate chemical analyses indicated f1.2 and 5.5 wt pct C to be present in the two samples taken of the specimen: no graphitic carbon was detected. One powder-diffraction pattern of this specimen indicated the presence of the tetragons: carbide reported earlier,3 (a = 6.772A, c = 9.427A), plus cementite (O), plus an unknown structure. The second powder-

Jan 1, 1970

By C. A. Stetefeldt

In a former paper (Runs., xxi., 286) I described the plant of the Marsac Refinery, and the manipulations of the process, but cou1d not, at the time, give reliable statistical results. To supply the latter is the object of the present paper. I shall give actual facts as correctly as possible, without any bias one way or the other. For all statistics I am indebted to Mr. W. G. Lamb, who has charge of the Marsac lixiviation-plant and refinery; to Mr. A. Luebeck, assayer at the Ontario mill; and to the Daly Office, Salt Lake City.* Before starting on the work of the year 1892, a most careful clean-up was made, and any remnants were charged to the refinery. During 1892 the Marsac lixiviation-works produced 48.8 tons of so-called "regular" sulphides, which contained, on an average, 11,449 ounces of silver per ton; 11.77 ounces of gold per ton; and 569.8 pounds of copper per ton. To this must be added, 266 pounds of sulphides and by-products left over from the product of 1891, which contained 1380 ounces of silver, 1.41 ounces of gold, and 63 pounds of copper. Before giving the results of the clean-up, a general discussion of the items of expense, methods of assaying, etc., is desirable.

Jan 1, 1895

By E. Furubayashi, T. Taoka, S. Takeuchi

Recrystallization textures developed from artificial nucleation around indentations were compared with spontaneously recrystallized textures in two rolled 3 pet Si-Fe single crystals with (111)[112] and (100) [011] orientations. Orientation of individual grains in some stages of their growth was also directly determined by a microetch-pit method. In both the crystals, the recrystallization texture was characteristic of each orientation regardless of any nucleation conditions, artificial or spontaneous, though artificially nucleated grains were more randomly oriented in finer stage. These results support the concept that the process of selection of growing grains controls the formation of the prejerred recrystallization texture. Discussion is given on the factors controlling the mobility of grain boundaries. Recrystallization textures are formed through a number of stages which are customarily called by the terms recovery, nucleation, and grain growth. Many experiments have been done to clarify the mech- anism of formation of recrystallization texture but no fully successful explanation has been proposed. The texture consists of oriented grains which nucleate at many sites of the deformed matrix and grow at the expense of the matrix during annealing. The current theories on the formation of recrystallization texture are based on the following two extreme hypotheses: 1) the oriented nucleation theory by Burgers et al.;1, 2 2) the oriented growth theory by Beck et al.3-5

Jan 1, 1968

By R. H. Hiltz, N. J. Grant

Solid-solution titanium-cerium alloys, cold-rolled to 0.010 in. thickness, and annealed, were internally oxidized to produce a fine dispersion of CeO2 in the titanium matrix. The oxidized alloys were cut into sheet stress-rupture specimens and tested for rupture life at 426°C, 538°C, and 648°C. There was noted an improvement in strength over that of pure titanium, the internally-oxidized alloys showing curves with a much flatter slope on the log stress—log rupture life plot, characteristic of the stable metal-metal oxide class of alloy. DURING the past 3 to 4-year period, considerable interest has been aroused by the potential offered by alloys based on the ultra fine dispersion of a hard insoluble phase in pure metals or solid-solution alloys for use at high temperatures. The impetus to the development and study of such alloys was provided by Irmann.1,2 through the success of the SAP alloy (pure aluminum containing about 12-14 volume pct of A12O3). Subsequent studies have thrown light on the true potential of this class of alloys in the remarkable stability of the structure after long-time exposure at high stresses and high temperatures.a-5 While success has been demonstrated in the special case of the A1-Al2O3 alloys, and more recently

Jan 1, 1959

By N. Arbiter, C. C. Harris

In 1961, a research program started at Columbia into the mechanical aspects of flotation,* and certain ends are now in view. The purpose of this note is to explain these tentative conclusions in the hope of stimulating discussion and eliciting new data, especially industrial data, with which to test the views expressed. The variables presently under consideration are impeller rotational speed, N, volumetric air rate, Q, and impeller diameter, D, the latter being the parameter chosen to designate cell size. The most favorable *The latest work 1 references all previous publications. chemical environment is not under discussion since the procedures for establishing it are better understood than those for optimizing N and Q by virtue of a longer history of more intensive investigation. THE GRADE AND RECOVERY SURFACES With a given ore, chemical treatment, and flotation machine, both grade, G, and recovery, R, are functions of N and Q. The GNQ and RNQ relationships are best viewed in terms of three-dimensional surfaces (Fig. 1) which are experimentally determinate.2 TO maintain grade at an acceptably high level, it is necessary for N and Q to lie within certain limits, and similarly with recovery. However, the ranges of N and Q for grade on the one hand and recovery on the other are rarely the same. Selecting the single N

Jan 1, 1970

Shovel To further increase the efficiency in the production of their foundry sand, the American Silica Sand Co. has purchased a new and improved shovel that will be used for loading trucks at their Reynolds Pit. The [ ] new shovel will greatly facilitate winter mining operations and make possible larger winter shipments of the company&apos;s foundry sand. The Reynolds Pit is one of three sand pits in the Ottawa district owned by American Silica which produce sand that is refined for foundry use. Circle No. 1 Electric Switches The Crane Electric Co. has just announced the production of their R-1000, a new rotating limit switch designed to control the travel of any rotating device requiring interruption or establishment of electrical current after a predetermined number of revolutions. It is useful for machinery, lifts, and other power equipment. The switch is presented in a finished case, 16 gage, reinforced, with walls of sufficient strength to hold the entire mechanism and all the parts in accurate alignment. The worm gear combination has a 60 to 1 ratio, sufficient for most industrial uses. The number of revolutions can still be increased by using various combinations of driving sprockets, either on the shaft of the switch, or on the sprocket of the unit controlled by the switch itself. Circle No. 2

Jan 1, 1952

By Edgar S. Burkhardt

In mining, the process of comminution starts at the pit and ends at the classifiers. The first machine that breaks or comminutes ore is the primary crusher. There are many types of crushers, but the one most commonly used in large tonnage plants is the gyratory so discussion is restricted to this type of machine. See Figure 1. The primary crusher is the most important piece of comminution machinery in the plant because every ton of ore processed by the concentrator must pass through it, as shown in Figure 2. Most plants can operate if a secondary crusher or a mill is shut down, but if the primary crusher stops, the whole concentrator goes down. It is, therefore, important that the machine be able to produce sufficient ore to keep the concentrator running without hesitation. The plant designer first considers the required daily capacity and an estimate of the size of the ore from the pit. To this he adds an availability factor to compensate for delays due to shovels, trucks and rou- [ ] tine maintenance at the crushing station. This factor is based on experience and can be on the order of 75% (1). With these figures, he determines the hourly capacity required of the primary crushing station to keep the concentrator supplied. See Table I.

Jan 1, 1982

By William C. Aitkenhead, John A. Jaekel

Uranium deposits in the Spokane Indian Reservation, as well as those around Mt. Spokane, are essentially low grade, much of the ore containing less than 0.2 pct U808. The Mining Experiment Station of the Division of Industrial Research, State College of Washington, has been engaged in intensive research on the amenability of these low grade ores to froth flotation. The results: successful flotation of autinite, chief mineral constituent. At the outset of this work the goal was a concentrate of 1 pct U308 with a 90 pct recovery from ores containing less than 0.2 pct U3O8. Most of the work has been done on argillite ore from the Midnight mine on the Spokane Indian Reservation. The goal has not been attained using this ore, but samples of the granite ore from Mt. Spokane yielded successful results. For example, a concentrate containing 11.2 pct U308 was produced from a Mt. Spokane high grade ore containing 1.27 pct U3O8 with a recovery of 97.8 pct. Another Mt. Spokane ore yielded a concentrate of 5.0 pct U3O8 from an ore containing 0.13 pct U3O8, with a recovery of 85 pct. This same ore gave a recovery of 93.5 pct when the grade of concentrate was reduced to 2.0 pct.

Jan 1, 1959

By J. S. Kirkaldy, R. J. Brigham

AS part of a program to investigate the diffusive properties of dilute ternary austenites we have made a determination of the effect of chromium on the activity of carbon in ? iron. Samples of pure iron and Fe-Cr alloys were simultaneously equilibrated at 1000°C with atmospheres of controlled CO/CO2 ratio following the procedures of Darken and Gurry 1 and smith.&apos; The 0.020 in. thick samples were analysed for carbon by microcombustion analyses3 to yield a set of isoacti-vity curves. The latter were converted to activity coefficient (standard state at infinite dilution) plots by combination with Smith&apos;s data2 for the activity of carbon in pure iron. Table I shows the compositions of the base alloys used while Fig. 1 shows the experimental results superimposed on a set of curves generated by the relation In?C=6.9NC- 10.7 Ne In the notation of wagner4 the interaction parameter is the second coefficient on the right, Sgr = - 10.7 This can be compared with a rather inaccurate value deduced from the transient equilibrium diffusion data of Kirkaldy et al.&apos; as The authors are indebted to the American Iron and Steel Institute for financial support. This material is condensed from a B.Sc. Thesis submitted to Mc-Master University by R.J.B.

Jan 1, 1963

By M. C. Fuerstenau, W. F. Cummins

The flotation response of quartz in the presence of calcium chloride and various fatty acids is presented. Flotation is not effected with lauric acid until calcium laurate is precipitated in solution, while flotation is obtained with the 9, 10, and 11-carbon members before precipitation of the calcium carboxylate. The active species responsible for flotation is suggested to be a basic aqueous complex, e.g. Ca(OH) (RCOO) (aq), and a possible mechanism of adsorption is given. Most of the previous work on activation in non-metallic flotation systems has involved the use of high molecular weight collectors, such as oleic acid or alkyl aryl Sulfonate.1-7 In these studies the levels of addition of collector and activator required for flotation were much above the concentrations necessary for precipitation of the metal-collector salt. In fact, Clemmer, Clemmons, Rampacek, Williams, and Stacy1 have stated, "Our experiments on a variety of materials have demonstrated that the metal salts which react with anionic collecting agents, as soaps and alkyl sulfates, to form relatively insoluble compounds may be employed as activating agents provided an optimum quantity is used at a proper pH." On the other hand, Gaudin and chang8 obtained flotation with additions of barium and lauric acid below the level required for barium lautate precipitation.

Jan 1, 1968

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II SEC. 1. The membership of the Institute shall comprise four classes, namely: 1. Members; 2. Honorary Members; 3. Associates; 4. Junior Associates. All members shall be equally entitled to the privileges of membership, excepting that Honorary Members, Junior Associates, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. Members shall comprise all those persons who on the third Mon- day of February, 1918, were members of the Institute, and in addition thereto, all those thereafter elected or transferred into the class of Members. A person to be eligible for election or transfer into the class of Members must be at least 27 years of age and must have had at least six years&apos; employment in the practice of engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership, shall be considered equivalent to two years&apos; employment, as required in the previous sentence. Employment as a teacher of engineering, mining, geology, metallurgy or chemistry, if in direct charge, may be considered a position of responsibility as specified in the second paragraph. Persons employed in research or any scientific literary work or in teaching in the scientific departments of colleges, approved by the Committee on Membership, who at the same time are engaged in consulting or in the active practice of mining, geology, or metallurgy, shall be entitled to consider the time so spent in active practice as equivalent to an equal length of time of employment in positions of responsibility, provided the work done or the positions held seem to the Committee on Membership to warrant the equivalency. The requirement of three years&apos; employment in positions of responsibility may be waived by the Committee on Membership in the case of persons who have done notable original work in mining, or metallurgy, or have won distinction by research or investigations In one or more of these subjects.

Jan 1, 1928

SEC, 1, This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc,; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II MEMBERS SEC. 1. The membership of the Institute shall comprise four classes, namely: 1. Members; 2. Honorary Members; 3, Associates; 4, Junior Associates. All members shall be equally- entitled to the privileges of membership, excepting that Honorary Members, Junior Associates, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot, SEC. 2, Members shall comprise all those persons who on the third Monday of February, 1918, were members of the Institute, and in-addition thereto, all those thereafter elected or transferred into the class of Members. A person to be eligible for election or transfer into the class of Members must be at least 27 years of age and must have had at least six years&apos;, employment in the practice of engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership,&apos; shall be considered equivalent to two years&apos; employment, as required in the previous sentence, Employment as -a teacher of engineering, mining, geology, metallurgy or chemistry, if in direct charge, may be considered a position of responsibility as specified in the second paragraph. Persons employed in research or any scientific literary work or in teaching in the scientific departments of colleges, approved by the Committee on Membership, who at the same time are engaged in consulting or in the active practice of mining, geology, or metallurgy, shall be entitled to consider the time so spent in active practice as equivalent to an equal length of time of employment in positions of responsibility, provided the work done or the positions held seem to the Committee on Membership to warrant the equivalency. The requirement of three years&apos; employment in positions of responsibility may be waived by the Committee on Membership in the case of persons who have done notable original work in mining, geology, or metallurgy, or have won distinction by research or investigations, in one or more of these subjects.

Jan 1, 1928

By Robert W. Fullerton, Donald T. King

INTRODUCTION AND THEORY by Robert W. Fullerton In coal preparation plants, as in any industrial operation where raw materials are handled, nuisance problems arising from the generation of dust are inevitable. Devices for the control or collection of dust are there- fore essential components of the plant process equipment. The general term "aerosol" is applied to small particles suspended in a gaseous medium, usually air, whose velocity under the force of gravity is small enough that the particles remain suspended for a reasonable length of time. Aerosols can be classified as dust, smokes, fumes, mists or fogs. Dust includes particles originally formed by pulverization of materials by such processes as crushing, grinding, drilling, blasting and abrasion. Smoke includes particles formed from the burning of organic materials. Fumes are particles formed by processes such as condensation and sublimation, usually at high temperatures. Mists or fogs are particles formed by the condensation of water or other vapors on some nuclei. The size of aerosol particles is generally designated in units of microns, there being 1000 microns to a millimeter and 25,400 microns to an inch. Particles of about 10 microns or above are visible to the naked eye. Table 14-1 shows size characteristics of the general classifications of particles discussed above and includes typical examples of particles commonly en- countered. Table 14-1 also shows the relationship between micron size and standard screen mesh sizes. Smoke and fume are usually in the range of 0.01 to one micron, dusts are in the range of one to 400 microns, mists are in the range of 0.1 to 100 microns, and fogs are in the range of one to 100 microns. For purposes of dust control, particles greater than 10 or 20 microns in size are considered large, particles one to 10 microns are considered fine and particles below one micron are ultrafine. Sources of Dust Because coal is relatively friable, the mining and subsequent handling operations break part of the coal into dust that can be readily carried by currents of air. In a coal preparation plant mechanical handling operations such as unloading, transferring from one belt to another, screening, cleaning, and crushing in a dry state result in the generation and release of varying amounts of additional dust. The dust problem, of course, is much less serious in plants employing entirely wet processing. In addition to dust from handling operations, thermal drying of the fine coal product frequently presents another dust collection problem. Most coal driers are

Jan 1, 1968