Search Documents

By J. R. Wylie, L. C. Huntley

Drilling for oil in the eastern producing states was fairly active during the first part of 1931, although less so than in 1930. With low prices development declined during the year, until the low prices of the summer resulted in an almost complete shut-down of drilling. This coincided with the action of the Conservation Board of the Pennsylvania Crude Oil Producers Assn, in limiting pipe line runs to 50 per cent of the 1930 normal for the Bradford district and upper country, and to 70 per cent for the balance of the region. Not only was new drilling halted but in many cases oil-producing properties were shut in. In November crude prices were partly restored, and all oil offered was being taken except in the Bradford district which was restricted to 80 per cent of the 1930 normal. During the latter part of the year drilling was being resumed on a moderate scale, and new production indicated a resumption of the proration order. The interest in gas development which has been under way for several years, maintained its supremacy over the search for oil in 1931. New reserves of importance were developed during the year in the Western Kentucky Coal Basin, in the Eastern Kentucky shale gas territory, in Stark County, Ohio, as well as the Oriskany sand development in northern Pennsylvania and central New York. A gas line was completed to the Eastern Seaboard serving Washington and Baltimore, and other lines were under construction designed to serve portions of the territory not hitherto supplied with natural gas. The low price of fuel oil at seaboard is understood to be the deterrent factor against further extension of natural gas lines to these markets at present. The development of these new reserves, as well as those developed by intensive drilling in old areas, resulted in the building up of large potential gas production and a lowering of rates paid to the producer. This, coupled with the country-wide tendency to lower the consumer rates of all public utilities, resulted in a general threat to reopen rate cases before various state commissions. Oil Development The past year was marked only by the almost complete shut-down of new development, reaching its low point during the summer, with its

Jan 1, 1932

By J. H. Richards, G. Derge, W. Peifer

A WIDE Variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware, They have been related to hydrogen largely by circumstantiat evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British committee on the Heterogeneity of Steel Ingots,' and current approaches to the problem were reviewed in a recent symposium of the AIME.I2 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principal object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem, The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow in However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross-section large enough to develop cracks, Yet small enough for convenient handling and sampling. Rails were also selected because they arc made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitat~s early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion, (2) Vacuum extraction (without melting), (3) Total combustion.

Jan 1, 1949

By G. Derge, W. Peifer, J. H. Richards

A WIDE Variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware, They have been related to hydrogen largely by circumstantiat evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British committee on the Heterogeneity of Steel Ingots,' and current approaches to the problem were reviewed in a recent symposium of the AIME.I2 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principal object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem, The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow in However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross-section large enough to develop cracks, Yet small enough for convenient handling and sampling. Rails were also selected because they arc made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitat~s early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion, (2) Vacuum extraction (without melting), (3) Total combustion.

Jan 1, 1949

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By J. H. Brophy

Experimental evidence in recent years shows that nickel coated hydrogen reduced tungsten powder can be sintered to 98 pct of theoretical density at 1100°C. New data indicate that the sintering rate is the same for nickel contents ranging from 0.125 wt pct (mon-atomic layer) to 5.0 wt pct Ni coated on 0.561. tungsten powder. Nickel tungsten made by coreduction from oxides sinters in a kinetically similar way, but the rate tends to increase with higher nickel contents. The activation of sintering can be accomplished with a minimum amount of nickel if coated powder is used. Transverse rmpture strength was found to increase in specimens containing 0.25 pct Ni as density increased during the initial stage of the carrier-phase sintering process. Upon the onset of grain growth in the final stage, strength was found to decrease. With increasing nickel contents up to 4 pct, strength increased. Maximum strengths in three-point loading were observed at 73,000 psi for 0.25 pct Ni and 93,000 psi for 5 pct Ni. These were comparable to that of massive tungsten recrystal-lized in the presence of nickel and tested in the same way. The results were sensitive to the mode of powder treatment and ductility was negligible in all cases. The study and application of sintered bodies of nickel and tungsten is not new; however, the analysis of the mechanism by which small additions of nickel increase the sintering rate of tungsten promises to Contribute new information regarding sintering theory in general. Initial experimental evidence was presented by the authors showing that nickel-coated hydrogen-reduced tungsten powder may be sintered to 98 pct of theoretical density at 1100°C in 16 hr.' Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the 'solution-precipitationo step postulated when the carrier phase is liquid3 although in the nickel tungsten case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in mi-crostructures at the temperatures under consideration. In the present work, new data for nickel-coated tungsten powder are offered in support of the proposed mechanism, and a more explicit study of the second stage of densification is presented. Concurrently, the sintering kinetics of these coated powders are compared to Ni-W powder made by coreduction of oxides. In this way the present work can be compared to earlier results in nickel activated sintering of tungsten in which the coreduction process was emplyed. The ultimate utility of such an activated sintering process will be determined to some extent by the mechanical and physical properties of the final prod-

Jan 1, 1962

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I). It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the 15 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remain¬ing to schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

By P. D. Merica

MY remarks are addressed to the question whether a program of international mineral control can effectively serve as a means of maintaining world peace in the kind of world envisaged by the Atlantic Charter. They do not touch the quite different questions whether such control could be appropriately used for postwar punishment of Germany and Japan, or for other purposes. I assume also that the question relates, not to the transition period immediately following the war, but to the more normal years which we hope will succeed this. Finally, they deal primarily with metals and metallic minerals rather than with. oil or coal or other minerals, although they may be applicable also to these other nonmetallic materials.

Jan 1, 1944

By R. B. Roof, J. J. Lombardo

DURING the course of investigations on U-Cb alloys by X-ray diffraction techniques, an impurity or an additional phase was observed in severa1 alloys of various compositions. The X-ray dif-

Jan 1, 1959

By L. G. Graper, E. L. Ramsey

THE present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semi-killed as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. ADDING SULPHUR AS A SULPHITE These difficulties can be avoided if sulphur is introduced into the steel by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which-upon decomposition-forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig, I shows photomicrographs of steels made with sulphur, while Fig, 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast-that is, before rolling and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions are more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. RESULTS As stated before, the sulphur dioxide is added to steel by means of the decompcsi-

Jan 1, 1942

By T. Seldenrath

In the development of a fluid -operated hammer drill' for accelerated penetration of hard rock formations in oil wells, a research investigation was conducted to evaluate the percussion effects obtained with different design characteristics and to determine the possibilities of percussion in the low frequency range. Tests were conducted on granite blocks and comparable impact forces were measured with a load cell under selected test conditions. These full-scale laboratory tests provided an evaluation of the effectiveness of percussion which was further supported by actual downhole field performance. While much pertinent data have been presented by other investigators the method of evaluation described in this article resulted in good correlation between laboratory and field performance and may be applicable in other low frequency percussion developments. EXPERIMENTAL METHOD For these tests the bit was held stationary and the test block was rotated and forced upward against the bit by a hydraulically-lifted rotary table. "Weight on bit" was calculated from pressure readings on the fluid system of the lifting cylinders—corrected for tare and friction. Percussion was obtained with several tubular hammers of different weights up to 320 lb. These were lifted mechanically and allowed to drop by gravity from various heights onto a slidably-mounted bit sub or "floating anvil" for calibration of the load cell response with known kinetic energy of the hammers. During evaluation of percussion effects, the hammers were hydraulically operated to provide a range of percussion frequencies up to 1,020 blows per minute delivered to the anvil. To obtain comparable test readings, the load cell of the strain gauge type, was attached to the bottom of the anvil or bit sub in place of the bit. The load cell rested on a typical granite test block mounted on the drilling table. The latter was hydraulically supported as in the actual drilling operation. The effect of support resistance was the same for all tools when calibrating. Impact forces so determined werethusdirectly comparable with one another for the purposes of this investigation. When a roller bit was substituted for the load cell for actual drilling, the impact force would probably be reduced due to the resiliency of the bit body, legs. cones and teeth and the penetration of the teeth into the rock. However, since the bits and rock specimens were uniform in these tests, an evaluation of actual tool performance, in terms of parameters previously determined with the load cell at the selected standard conditions of calibration, proved satisfactory. Throughout these tests, 8¾-in. standard tricone, hard rock toothed roller bits and carbide-insert roller bits were used. Rotary speeds were 50 and 100 rpm; static weight on bit was applied up to 40,000 Ib, and percussion frequencies up to 1,020 blows per minute were available. During this investigation it was found that toothed bits on which the teeth had developed flat ends about 3/16 in. wide did not change appreciably for the duration of a test. Hence, all toothed bits used in this study were in this condition. Conventional reference curves obtained in these tests show that increasing weight on hit by 2:1 yielded an increased penetration rate of approximately 2.7:1, while an increase in rotary speed of 2:1 netted an increased penetration rate of roughly 1.7:l. Results are thus of the same order as those reported for hard rock drilling by other investigators." CALIBRATION Under the selected standard test conditions previously described, with the lifting table hydraulically supported, and the anvil interposed between hammer and load cell, the hammers were dropped from known heights. Thus, with the kinetic energy of the hammer known, the corresponding maximum impact force shown by the cell was determined. (It may be of passing interest to note here that special drop tests with the hammers showed that no appreciable reduction in impact force resulted from introduction of the anvil or hit sub.) From these calibrations, it was possible to determine the theoretical kinetic energy available in the hammer from the maximum impact force shown by the load cell while operat-

By F. X. Tartaron

The comparison of actual energy of comminution with theoretical surface energy presents a wide gap. On the other hand, Solid State Theory presents a viewpoint that places actual energy of breakage in understandable relationship with the theoretical strength of materials. Therefore the physical background of comminution theory favors Kick's Law. A11 discussions of comminution theory appear farfetched when comparison is made of the actual energy of crushing with the energy input called for by thermodynamic theory. Quoting Taggart:' "The work required to crush halite was of the general order of 0.10 kg cm per sq cm of new surface produced (based on air percolation) whereas the theoretical energy of this new surface, based on thermodynamic calculation by a number of investigators is 1 x 10'4 kg cm per sq cm or the work expended was 1000 times the new surface energy — an indicated crushing efficiency of 0.10 pct." It is frustrating to probe into comminution theory with the prospect that the energy one is measuring is 99.9 pct waste energy. Do the laws of comminution deal with energy consumed by mineral breakage or with waste heat energy? There seems to be something wrong. Solid State Theory may provide the answer. The following statement is particularly apt to the situation: "The fundamental fact about metals and indeed all materials, is that they are much weaker than they should be. By this, we mean that if the stress required to cause a given plane of atoms to slip past a neighboring plane is calculated from basic atomic and Solid State Theory, the resulting number is some 1000 times too large to be accounted for by errors in approximations or assumptions. We know now that this is due to dislocations, and we even have a fair understanding of the details of the process by which dislocations make a crystal weak. An intriguing possibility which suggests itself, results from the discovery of very minute metallic crystals which are apparently free of dislocations and which have a strength approaching the ideal value for a perfect crystal." Here we have an extraordinary reversal of the situation. The actual energy for breakage is only one-thousandth the theoretical instead of 1000 times as given by Taggart. But the theoretical energy presented by Solid State Theory is the binding energy between atoms (or ions) in a crystal lattice. This is the kind of energy envisaged by Kick's law. The surface energy or the other hand corresponds to Rittinger's law. Comparison of theoretical with actual, on the basis of surface or on the basis of Rittinger's law, seems to present an absurdity; yet Rittinger's law is confirmed by an impressive array of experimental evidence. Comparison of theoretical and actual on the basis of Solid State Theory or, in other words, on the basis of Kick's law seems reasonable; yet there is not a scrap of evidence to verify Kick's law. The situation appears paradoxical, but the developments in the next section of this paper show that the paradox is a hint to a strange turn of events. ENERGY-WEIGHT FRACTION FUNCTION charles3 has presented a final equation showing the relation of energy consumed in comminution to size of product n{-1) a-n + 1 E is energy, C is proportionality constant, a and n are constants and k is the coarsest size in the ground product (size modulus). In the course of study of a large amount of experimental evidence, Charles discovered that in the general case, a-n + 1 approximated zero. For some reason, a and n differed only by unity. But if a—n + 1 = 0 within experimental error, then it is obvious that Eq. 1 states that it requires an infinite amount of energy to grind any sample to any size. This is a case where nature gives an absurd answer to a man-made mathematical equation, hence something is wrong with the equation. An adjustment must be made to fit the equation with experience. TO reveal the nature of the adjustment, the differential equation preceding the second integration in Charles' group of equations is given When Charles integrated the quantity xa-n it was almost impossible for him to realize that he was dealing with a special case of integration and that

Jan 1, 1962

By W. A. Backofen, D. Lee

Tlze condition of superplasticity or neck-resistanl flow that results front high strain-rate sensitivity has been observed in isothermal tension tests on several titanium alloys and one of zirconium hi general, il was associated with reasonably fine-grain micro-structures being stvained in the transformation range at rates below i - 10 -3 sec-&apos;. The metallographic mean-free path, L, was measured at room temperature after rapid cooling from the temperature of test-ing. The flow stress of Ti-GAL-4V at 950°C was proportional to La at different constanl <; the value of a decreased with increasing. E but at E< 1.5 x 10-4 sec-1 it varied only from 0.9 to 1.25. The findings were interpreted to mean that viscous boundary shear is the rate-controlling process of deformation at high levels of strain rate sensitivity in these materials. Elongation of over 1000 pet could be obtained, but a1 temperatures so high and rates so low that any practical application of the full effect would probably be difficult. As the transformation range was narrowed, by turning from Ti-6AL-4V to Ti-5Al-2.5sn to nomznally pure titanium, the allowable temperature varialion was correspondingly reduced. Superplasticily was not found in Armco iron, presumably because the transformation range was too narrow to allow the developtnenl of a reasonably stable microstructure for isolhermal lesting. THE work represented by this paper grew out of a recent study of texture hardening in a(hcp) titanium and zirconium-alloy sheet,&apos; of which part has now been published.2 It was found that, with heating, the tensile plastic-anisotropy index, R,* was decreased from well above 1 towards 1 as the temperature range for the a(hcp) -ß(bcc) phase change was entered. The clearest example of that trend is illustrated with previously unpublished data in Fig. 1. It might have been thought that such a development resulted simply from introduction of the cubic and therefore plastically less anisotropic phase. However, the accompanying change in the index of tensile strain-rate sensitivity, m = a log a/a log E, was rapidly upwards, to a high of 0.85 in some cases (also illustrated in Fig. 1). At the same time, the total tensile elongation rose to a maximum and the flow strength dropped away as R (and m) approached 1. Taken together, the observations cannot be understood as resulting from the presence of cubic phase, per se. It has been concluded instead that they reflect the largely noncrystallographic deformation which characterizes superplasticity. As demonstrated in other recent work? a necessary condition for super-plasticity is strain-rate sensitivity of flow stress sufficiently high that m is above a lower limit of -0.3. The origin of large m has been traced, in turn, to grain size so small that a substantial amount of viscous deformation is introduced by such processes as Nabarro-Herring diffusional flow4 and/or grain boundary shear.5,6 Because of problems in the processing of titanium and zirconium alloys—problems of high strength, limited ductility, and excessive springback, originating largely in slip resistance-it was natural to wonder if something useful might be done with superplasticity in those materials. Therefore experiments were made for more closely identifying and generally bounding the phenomenon with temperature and strain-rate limits, before attempting to decide about its exploitation. The results are being reported here. EXPERIMENTAL Materials. The two of primary interest were the titanium alloys of nominal composition (in wt pct) 5A1-2.5Sn and 6A1-4V. Others were a 4A1-1/4O2 titanium alloy, titanium of commercial purity (RC-70), Zircaloy-4. and Armco iron. All were received as annealed 3/16 in. thick sheet, except RC-70 which was & in. thick, and tested in that condition. Details of transformation temperature and grain size are given in Table I. The results of dilatometry for the measurement of transformation temperatures were unsatisfactory. Data were finally obtained by metallographic examination of each specimen after test, to determine from the amount of transformed 4 where the specimen had been heated in relation to the critical temperatures. Results were in reasonable agreement with information from the supplier. Strip tensile specimens were of full sheet thickness and taken along the rolling direction, except for those

Jan 1, 1968

By E. V. Foran

Among the many newer disclosures that have accompanied the petroleum industry&apos;s progressively deeper exploratory drilling is the increased frequency with which the operators are encountering reservoirs of which the products at the time of discovery exist wholly or predominantly in the gas phase. The popular term "distillate pool" is most often used within the industry when referring to this type of reservoir, and in this paper the term is used in that sense. These pools have been observed in many different surroundings. In some places the entire reservoir is filled with the wet gas containing its water-white condensible products in the gas phase but apparently with no dark oil or other hydrocarbon liquids in the reservoir. The 8200-ft. horizon in the Big Lake field in West Texas is a good example of this type. At other places the wet, or distillate-bearing, gas may form a large gas cap directly overlying and in contact with an extensive reserve of dark oil. Oklahoma City, Kettleman Hills, the 8500-ft. horizon in the Big Lake field, and many others are examples of this type. There are also many places in which the wet distillate-bearing gas fills nearly the entire reservoir space, while the dark oil occupies only a narrow, bandlike zone, which marks the boundary of the reservoir along its lowest productive contour. The heavier components of these deep pool gases are generally water white in color, a large portion of which are condensible in a conventional oil and gas separator, when operated under pressures of the order of 400 to 800 Ib. per sq. in. Although the water-white products recovered in the separator sometimes have end points of 650" F. and higher on standard Engler distillation, they occur only in the gas phase in the reservoir. It is entirely possible that even some small amounts of dark colored reservoir components may occur in the gas phase when the temperature is 300" F. and pressures exceed 6000 Ib. per sq. in. Close approaches to these conditions have been encountered in the deepest producing wells. The condensible content of the deep reservoir gases of the many pools that have been tested or produced to date shows a wide variation in both condensible content, per 1000 cu. ft. of gas, and physical character.

Jan 1, 1939

By David Reger

LITTLE new oil was found in West Virginia, during 1923, but there were important discoveries of gas. Most of the large oil producers have contented themselves with pumping old wells or in drilling only enough new wells in defined territory to maintain a fairly constant production, the attitude being that no, profit is made in producing high-grade oil at a low price and that an eventual loss is sustained by draining the reserves of a limited commodity that, at some more favorable time, will be of much value. The representative of one large company said: "We have done nothing but pump old wells during 1923 and we have made no plans for 1924." Careful attention to producing wells has been the rule, there having been few abandonments; the belief is prevalent that small wells will eventually become profitable under more favorable marketing conditions. In natural gas, the opposite point of view prevails. Because of the vast capabilities of the state for producing gas, its output being ahead of all others, great systems of transportation and distribution into the markets of four adjoining states have been built and a demand has been created that no present, or apparently potential, production can satisfy. This demand has become so great that large distributing companies not only discourage new applications for service but advise old customers to install coal furnaces for auxiliary fuel; some have requested public-service commissions to grant higher &apos;rates against large industrial consumers than those allowed for domestic heating. The response to this known market has been a rapid increase in price, both at the well mouth and at the door of the ultimate consumer, and the industry has become so stable that the only uncertainty, or hazard, appears to be the question of the presence of gas in fair quantity in a given territory under consideration. Several oil companies have now forsaken their policy of selling gas, wells outright when drilled and ;have organized gas departments to drill for gas and to dispose of the daily output by meter to distributing corporations. With such companies and with other producers whose interest is chiefly gas, the year has been busy and profitable. Some new territory of apparently large value has been proved and deeper producing sands in old fields have been tapped.

Jan 3, 1924

By E. V. Foran

Among the many newer disclosures that have accompanied the petroleum industry&apos;s progressively deeper exploratory drilling is the increased frequency with which the operators are encountering reservoirs of which the products at the time of discovery exist wholly or predominantly in the gas phase. The popular term "distillate pool" is most often used within the industry when referring to this type of reservoir, and in this paper the term is used in that sense. These pools have been observed in many different surroundings. In some places the entire reservoir is filled with the wet gas containing its water-white condensible products in the gas phase but apparently with no dark oil or other hydrocarbon liquids in the reservoir. The 8200-ft. horizon in the Big Lake field in West Texas is a good example of this type. At other places the wet, or distillate-bearing, gas may form a large gas cap directly overlying and in contact with an extensive reserve of dark oil. Oklahoma City, Kettleman Hills, the 8500-ft. horizon in the Big Lake field, and many others are examples of this type. There are also many places in which the wet distillate-bearing gas fills nearly the entire reservoir space, while the dark oil occupies only a narrow, bandlike zone, which marks the boundary of the reservoir along its lowest productive contour. The heavier components of these deep pool gases are generally water white in color, a large portion of which are condensible in a conventional oil and gas separator, when operated under pressures of the order of 400 to 800 Ib. per sq. in. Although the water-white products recovered in the separator sometimes have end points of 650" F. and higher on standard Engler distillation, they occur only in the gas phase in the reservoir. It is entirely possible that even some small amounts of dark colored reservoir components may occur in the gas phase when the temperature is 300" F. and pressures exceed 6000 Ib. per sq. in. Close approaches to these conditions have been encountered in the deepest producing wells. The condensible content of the deep reservoir gases of the many pools that have been tested or produced to date shows a wide variation in both condensible content, per 1000 cu. ft. of gas, and physical character.

Jan 1, 1939

By Eugene W. Pearson

In a marked departure from conventional practice, the Power Plate process combines the two unit operations of leaching and electrowinning into a single continuous step for direct recovery of copper from sulfide concentrates, cement copper, copper scrap, and copper oxide slurries. Considering how environmental controls are pre- venting development of smelters for additional capacity or new construction, the Power Plate process provides a welcome pollution-free alternative to the smelting-electrorefining routes. And its low capital investment and low operating costs also recommend it to copper producers who are now using or investigating various hydrometallurgical methods.

Jan 12, 1974

By A. U. Seybolt, C. H. Mathewson

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrence of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below.

Jan 1, 1935

By G. D. Van, Arsdale

IT IS particularly appropriate that a paper on this subject should be presented in Spanish, before a Spanish speaking audience, and in a South American country, first because of the facts that these countries today have not only the largest copper leaching plant in existence but also present great opportunities for future extension of hydrometallurgy; and second, because of the fact that the first copper made by any wet method was doubtless produced before existing records at the Rio Tinto deposits in present day Spain.

Jan 1, 1925

By R. E. Cech

Particles -3 to 30 µ diam of a 29.5 pet Ni, 70.5 pet Fe alloy after being melted and solidified while falling through a hydrogen atmosphere were found to contain a distortion-free body-centered-cubic phase. In most particles, the amount of body-centered-cubic phase approaches or equals 100 pet. It was shown by a series of experiments that this phase forms directly from the liquid. It is pointed out that a mechanism previously suggested in recent papers on the theory of the liquid-solid transformation can account for the solidification of body-centered-cubic phase in a temperature range where face-centered-cubic is the stable phase. IN the course of an operation to produce powders for a study of the martensitic transformation in Fe-Ni alloys, an unexpected phenomenon was observed. Powders of a 29.5 pet Ni alloy, which has a subzero M, temperature, were found to contain considerable amounts of a body-centered-cubic phase at room temperature. The experiments to be described were designed to elucidate the mode of formation of this unexpected phase. Experiments and Discussion An alloy containing 29.5 wt pet Ni, balance iron, was vacuum melted from high purity electrolytic iron and carbonyl nickel shot and solidified in the crucible. The metal was converted to oxide, ground to 100 pet <37µ, pressed to a cake, and homogenized 20 hr at 1350°C. To insure homogeneity the grinding, pressing, and homogenizing heat treatment was repeated a second time. The oxide was then ground to 100 pct <37µ and hydrogen reduced at 500°C. The reduced powder was given a spheroidizing treatment to produce spherical cast particles. The treatment consisted of dispersing the particles in hydrogen and allowing them to drop through a vertical hydrogen furnace set to a temperature higher than the liquidus of the alloy. This operation, commonly known as shotting, has been described more fully elsewhere.&apos; The powder produced by this method was found to contain approximately equal parts of body-centered-cubic and face-centered-cubic phases. A magnetic separation technique, previously described,&apos; was applied, and it was found that particles were either completely face-centered-cubic or nearly completely body-centered-cubic. The microstruc-

Jan 1, 1957