Search Documents

By G. P. Tiwari

Recrystallization and grain growth in thoria dispersed nickel and nichrome were recently studied by Webster as a function of temperature and deformation. The unexpected part of these results was that specimens which had received heavier deformation developed greater resistance to recrystallization. Retardation of recrystallization was accompanied by the formation of voids around thoria dispersion. To explain these results, Webster suggested that the formation of void around the particles increased the effective size of thoria particles. This resulted in greater impediment to the grain-boundary migration and as a consequence the recrystallization of the matrix is retarded. In the present note an alternative and more probable explanation for the effect of voids on recrystallization is presented. The exact mechanism of void formation in thoria dispersed nickel or nichrome is not known. However, it is reasonably certain that it must be preceded by the stress concentration in the matrix around thoria dispersion during the deformation.'' The resulting stress concentration must be sufficient enough to supply the surface energy for the new surfaces created. Further, the decrease in the strain energy of the matrix surrounding the potential void nucleus must be larger than the surface energy of the newly created surface. The release of strain energy due to formation of crack results in a strain free cylinder of the material around the voids.13 If the void formation is not localized, at few points only (as is the case here), this process may lead to considerable amount of release of strain energy of the matrix. The pattern of recrystallization behavior of single phase homogeneous matrix as well as the matrix having a second phase dispersion is same except for the fact recovery and recrystallization are more clearly delineated.14 In general, the recrystallization temperature is lowered (i.e., recrystallization is easier) with increase in the amount of cold work. This is due to the increase in stored energy in the matrix with increasing amount of deformation. If somehow there is a relaxation of strain energy in the matrix, the recrystallization should become difficult because of the decrease in the amount of stored energy available for recrystallization. Since the formation of voids leads to a decrease in the strain energy of matrix, the recrystallization of the matrix would be inhibited due to the formation of voids during deformation prior to recrystallization. It has been observed by earlier workers15'16 that the presence of preexisting voids in a matrix retards the recrystallization. The essential issue here is how do the voids act to produce this effect. If the voids influence recrystallization only by blocking the grain boundary migration, then the effect should be maximum when they are present almost exclusively along grain boundary. These conditions are obtained during high temperature deformation. However, the voids produced due to creep along grain boundary are not able to prevent recrystallization17 suggesting that they are not effective in blocking grain boundary movement. Recently it was shown by Davies and Williams that the voids can act as sinks for vacancies." As a result the processes dependent on vacancy diffusion like recovery, recrystallization, dislocation climb, and so forth, will be hindered. This fact may be responsible for inhibition of recrystallization during subsequent deformation and annealing cycles. It is to be noted here that there is a large difference between the density of voids in creep experiments and the other experiments where retarding effect of voids on recrystallization is seen. The voids in former may number up to l04 to l05 per sq cm whereas in latter cases the voids density is typically around 1010 to 1013 per sq cm. It appears that the decrease in supply of vacancies in creep is insufficient to adversely affect the recrystallization due to low void population. The author is grateful to P. Das Gupta and S. P. Ray for helpful discussions. Author's Reply D. Webster Tiwari appears to have misunderstood the nature of grain boundary-particle interactions. Tiwari (quoting Cahn) states that second phase particles become more effective as they become smaller, therefore as the voids in TDNiC make the thoria particles effectively bigger their ability to resist grain boundary movement is impaired. This particle size argument was originally proposed in the form of an equation by Zener 20 years agol9 and is not necessarily valid as is discussed below. However, assuming it is valid, it predicts a greater boundary restraining effect by smaller particles simply because their combined cross sectional area is greater at a constant volume. If the number of particles remains the same and their effective size increases, as in the present case, Zener's equation predicts a greatly reduced grain size. This is because the effect

Jan 1, 1970

By Robert Bell

The regions to which this paper refers include the whole of the Dominion of Canada east of the 130 Rocky Mountains and north of the water-shed of the St. Lawrence. Very little exploration for economic minerals has yet been done in this immense country; but that little has already served to indicate great wealth in some localities. Having been engaged for a number of years in conducting government geological explorations in these vast territories, I shall endeavor to give the members of the Institute an idea of the prospective mineral resources of almost half a continent, as far as they are yet discernible. I purpose confining my observations to the economic minerals, and will not attempt a description of the geology of these territories; hut it will be necessary to say a few words about the rocks in order the better to explain the distribution of such minerals. The Laurentian nucleus of the continent is the principal feature of the geological map of the Dominion. It stretches from Lake Superior to Baffin's Bay, and from Great Bear Lake to the Straits of Belle Isle. Hudson's Bay itself, which is half the size of the Mediterranean Sea of the old world, lies in the center of this area. Its shores are bordered in places with newer rocks. On the west side of James' Bay (its southern prololigation) these extend inland over 200 miles, and consist of fossiliferous Devonian and Silurian strata. On the western and northwestern side of Hudson's Bay proper, altered rocks are met with, some of which resemble the gold-bearing strata of Nora Scotia, some the Huronian of Lake Huron, some the older Huronian, and others the crystalline series of the neighborhood of Sherbrooke in the Province of Quebec. Along the east coast (called the Eastmain)and among the islands lying off it, there is an interesting set of volcanic and sedimentary rocks which appears to be identical with the Animikie and the Nipigon series of Lake Superior. The area which I have characterized in a general way as Laurentian, includes tracts and belts, more or less extensive, of the Huronian series. Such areas appear to be most common, and have been best explored, in the country between the Great Lakes and Hudson's Bay.

Jan 1, 1886

By H. F. Yancey, O. L. Furse

Although usually coal is screened with punched plate screens having round-hole perforations, there has been an increasing use of wire-cloth screens with square apertures, especially at pneumatic coal-cleaning plants and at other plants that use vibrating screens. It is therefore desirable to establish a relationship between round-hole and square-hole screens for use not only in experimental investigations of coal-preparation problems, but also for use in commercial operations. This need is apparent whenever it is necessary to substitute wire cloth for punched plate and still retain the familiar trade-size product. Although similar work probably has been done by industrial organizations concerned with the screen sizing of coal, the only recorded study of the subject other than the one described herein of which the authors are aware is that of Roesler,1 who screen-sized two samples of limestone and two of zinc concentrates crushed to pass 1/2 in. with a set of square and round-hole screens and found the ratio to be 1:1.23. Procedure In the course of a study of various methods for determining the friability of coal,2 it was necessary to screen-size the products of a series of friability tests of three different coals with both round-hole and square-hole screens. The coals used were from the Roslyn No. 3 and the Bayne mines in Washington and the Rolapp mine in Utah. Twenty 25-lb. samples of each of these three coals at 3 to 2 1/2 in. round-hole size were dropped from a height of 10 ft. to a concrete floor, and then screened with

Jan 1, 1934

By J. W. Spretnak, G. W. King

THE crystallography and morphology of 0-Al,Fe precipitates in an A1 + 0.5 wt pct Fe alloy have been studied by transmission electron microscopy. The alloy was cast in cylindrical ingots, 15 cm in diameter and 60 cm in length, and cooled slowly. The measured composition was 0.527 wt pct Fe, 0.001 wt pct Mg, and 0.003 wt pct Cu. Spectrographic analysis revealed no additional trace impurities. Thin slices were cut from the ingot and reduced by more than 95 pct by rolling to a thickness of 0.1 mm with no intermediate annealing treatments. These thin sheets were then vacuum-annealed for 1 hr at 612°C and air-cooled in their capsules. Thin foils for examination in the electron microscope were prepared by electropolishing. The precipitate is found in the form of oval platelets on the (110) planes of the matrix. The major axes of the platelets are parallel to the (110) directions of the matrix, and vary in length from 1/2 to 2 p. The thickness is about 1/10 p. Examples of platelets, both in the plane of the foil and normal to the foil, are shown in Figs. l(a) and l(b), respectively. lack' found that ?-A13Fe (more correctly All13Fe4) belongs to the monoclinic system. Using Black's structural data and simultaneous electron-diffraction patterns from the matrix and precipitates, the habit planes and directions were determined to be: (00l)? || (110)Al [100]? || [001]Al The orthogonal crystallographic axes of the precipitates are accurately in the habit plane, while the measured coincidences of the directions are only within 10 deg. The major axis of the platelet is parallel to [010] in the 0. This orientation corresponds to the direction of nearest registry of the lattices.

Jan 1, 1964

By T. F. Witherbee

In the sections, Figures 1, 2, and 3, are shown three crucibles that have been applied to substantially the same furnace, all the conditions having been the same except a variation of one foot of bosh, and a slight variation in the angle of the same. The bosh of No. 3 was originally the same as No. 2, the additional foot in diameter being the result of three months' cutting. Beginning with No. 1, which mas 5 feet 6 inches diameter, with tuyeres 5 feet 4 inches high, and cinder-tap four feet from bottom, great trouble was found in holding iron a proper length of time, four hours being the outside limit when working well, and two hours or less if working badly. "Break-outs" through the iron

Jan 1, 1880

By P. A. Laxen, H. R. Spedden, A. M. Gaudin

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface1 are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.2,3 Study of the adsorption of sodium from an aqueous solution on quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained.4,5 Three main factors which appeared likely to affect the adsorption of sodium are: 1-concentration of sodium in the solution, 2-concentration of other cations in the solution, and 3-anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in the amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxylion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory4 except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying5 To minimize the laborious preparation of quartz, experiments were made to determine whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na' activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot II) and 2000 (lot III) as determined by the Bloecher method.6 Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.7 It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß radiation and a 1.30 mev ? radiation. The decay scheme is illustrated in the following equation: [Y Nam S. - 'Net 3 years] The ß radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang8 The original active material was 1 ml of solution containing 1 millicurie of Na22 as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen5 In brief, it included the following steps: 1-Ascertainment of linearity between concentration of Na22 and activity measured. 2-Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3-Taking precautions to avoid evaporation of water during centrifuging.

Jan 1, 1952

By Samuel G. Lasky

The writer has been interested in determining the mineralogic dis-t,ribut.ion of silver in the base-metal ore of thc Ground Hog mine of the Asarco Mining Co. in the Central mining district of New Mexico.' This ore consists of a varitextured mixture of sphalerite, chalcopyrite, galena and pyrite in a quartz gangue. The average ore contains 14 per cent of zinc, 9.5 per cent of lead, 5 per cent of copper, and 10 oz. of silver per ton. Generally it is accepted that the silver in ores of this type, in which no definite silver minerals can be recognized, is contained in the base-metal minerals. Published assays of pure mineral specimens from many districts show that each of the base-metal minerals contributes in some degree to the total silver content of the ores, and to determine the proportionate amount contributed by each mineral in any specific ore it has been the practice to assay selected specimens of each mineral, the purity of which has been determined microscopically. There being no such assays available for the Ground Hog ore, and it being impracticable to have enough of them made to give average results, the writer resorted to a mathematical attack upon composite assays of large quantities of ore and concentrates. Surprising results were obtained, and it is the threefold purpose of this paper to present these results, to describe the mathematical method used, and to point out the value of using this method even when assays of pure specimens are available. Value of the Mathematical Method The obvious way of attacking the problem would be to separate cleanly large quantities of ore into its component minerals and then to determine the average silver content of each mineral by assay of representative samples. Since an absolutely clean separation is not feasible, it has been the practice, as mentioned above, to assay pure specimens of the different minerals. No one will contend seriously that the silver content of a base-metal mineral is constant throughout any particular deposit, and it will

Jan 1, 1935

By Samuel G. Lasky

The writer has been interested in determining the mineralogic dis-t,ribut.ion of silver in the base-metal ore of thc Ground Hog mine of the Asarco Mining Co. in the Central mining district of New Mexico.' This ore consists of a varitextured mixture of sphalerite, chalcopyrite, galena and pyrite in a quartz gangue. The average ore contains 14 per cent of zinc, 9.5 per cent of lead, 5 per cent of copper, and 10 oz. of silver per ton. Generally it is accepted that the silver in ores of this type, in which no definite silver minerals can be recognized, is contained in the base-metal minerals. Published assays of pure mineral specimens from many districts show that each of the base-metal minerals contributes in some degree to the total silver content of the ores, and to determine the proportionate amount contributed by each mineral in any specific ore it has been the practice to assay selected specimens of each mineral, the purity of which has been determined microscopically. There being no such assays available for the Ground Hog ore, and it being impracticable to have enough of them made to give average results, the writer resorted to a mathematical attack upon composite assays of large quantities of ore and concentrates. Surprising results were obtained, and it is the threefold purpose of this paper to present these results, to describe the mathematical method used, and to point out the value of using this method even when assays of pure specimens are available. Value of the Mathematical Method The obvious way of attacking the problem would be to separate cleanly large quantities of ore into its component minerals and then to determine the average silver content of each mineral by assay of representative samples. Since an absolutely clean separation is not feasible, it has been the practice, as mentioned above, to assay pure specimens of the different minerals. No one will contend seriously that the silver content of a base-metal mineral is constant throughout any particular deposit, and it will

Jan 1, 1935

The writer has been interested in determining the mineralogic dis-t,ribut.ion of silver in the base-metal ore of thc Ground Hog mine of the Asarco Mining Co. in the Central mining district of New Mexico.' This ore consists of a varitextured mixture of sphalerite, chalcopyrite, galena and pyrite in a quartz gangue. The average ore contains 14 per cent of zinc, 9.5 per cent of lead, 5 per cent of copper, and 10 oz. of silver per ton. Generally it is accepted that the silver in ores of this type, in which no definite silver minerals can be recognized, is contained in the base-metal minerals. Published assays of pure mineral specimens from many districts show that each of the base-metal minerals contributes in some degree to the total silver content of the ores, and to determine the proportionate amount contributed by each mineral in any specific ore it has been the practice to assay selected specimens of each mineral, the purity of which has been determined microscopically. There being no such assays available for the Ground Hog ore, and it being impracticable to have enough of them made to give average results, the writer resorted to a mathematical attack upon composite assays of large quantities of ore and concentrates. Surprising results were obtained, and it is the threefold purpose of this paper to present these results, to describe the mathematical method used, and to point out the value of using this method even when assays of pure specimens are available. Value of the Mathematical Method The obvious way of attacking the problem would be to separate cleanly large quantities of ore into its component minerals and then to determine the average silver content of each mineral by assay of representative samples. Since an absolutely clean separation is not feasible, it has been the practice, as mentioned above, to assay pure specimens of the different minerals. No one will contend seriously that the silver content of a base-metal mineral is constant throughout any particular deposit, and it will

Jan 1, 1935

By Samuel G. Lasky

The writer has been interested in determining the mineralogic dis-t,ribut.ion of silver in the base-metal ore of thc Ground Hog mine of the Asarco Mining Co. in the Central mining district of New Mexico.' This ore consists of a varitextured mixture of sphalerite, chalcopyrite, galena and pyrite in a quartz gangue. The average ore contains 14 per cent of zinc, 9.5 per cent of lead, 5 per cent of copper, and 10 oz. of silver per ton. Generally it is accepted that the silver in ores of this type, in which no definite silver minerals can be recognized, is contained in the base-metal minerals. Published assays of pure mineral specimens from many districts show that each of the base-metal minerals contributes in some degree to the total silver content of the ores, and to determine the proportionate amount contributed by each mineral in any specific ore it has been the practice to assay selected specimens of each mineral, the purity of which has been determined microscopically. There being no such assays available for the Ground Hog ore, and it being impracticable to have enough of them made to give average results, the writer resorted to a mathematical attack upon composite assays of large quantities of ore and concentrates. Surprising results were obtained, and it is the threefold purpose of this paper to present these results, to describe the mathematical method used, and to point out the value of using this method even when assays of pure specimens are available. Value of the Mathematical Method The obvious way of attacking the problem would be to separate cleanly large quantities of ore into its component minerals and then to determine the average silver content of each mineral by assay of representative samples. Since an absolutely clean separation is not feasible, it has been the practice, as mentioned above, to assay pure specimens of the different minerals. No one will contend seriously that the silver content of a base-metal mineral is constant throughout any particular deposit, and it will

Jan 1, 1935

By T. F. Witherbee

IN the sections, Figures 1, 2, and 3, are shown three crucibles that have been applied to substantially the same furnace, all the conditions having been the same except a variation of one foot of bosh, and a slight variation in the angle of the same. The bosh of No. 3 was originally the same as No. 2, the additional foot in diameter being the result of three months' cutting. Beginning with No. 1, which was 5 feet 6 inches diameter, with tuyeres 5 feet 4 inches high, and cinder-tap four feet from bottom, great trouble was found in holding iron a proper length of time, four hours being the outside limit when working well, and two hours or less if working badly. "Break-outs" through the iron

Jan 1, 1880

By E. Lancaster-Jones

THE gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i, e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eötvös, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any, rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features.

Jan 1, 1928

By R. A. Greenkorn

This project originated in a practical problem—we needed five tracers that could be used together to locate flow paths in a pilot flood. While tracers for subsurface liquids have been used since the turn of the century,1-15 none of those reported in the literature appeared to be either consistent or quantitative enough for our purposes. Most were used in field systems without controlled experiments to determine the accuracy and precision of analysis, and many were tracers that could not be used collectively. The ideal tracer, of course, would follow the fiuid of interest exactly, traveling at the same velocity as the fluid front. But the ideal is impractical to attain because adsorption-desorption effects cause the tracer to lag behind the front; these effects, plus diffusion-dispersion effects, cause the tracer front to spread more than the fluid front. Thus, our objective was not to locate a tracer that would be ideal for all circumstances but rather, to find one that would approximately follow the fluid, or one that under controlled conditions could be corrected to calculate the movement of the fluid front. We considered tracers satisfactory—(1) if they were easy to analyze; (2) if their breakthrough-elution curves were not too different from those for the chloride ion, a tracer believed to follow the fluid front closely; and (3) if we could calculate from the curves a material balance, at 1.25-PV (pore volume) injected, within 5 per cent of that calculated from chloride curves. Of a possible 35 materials, we selected 13 tracers that could be quickly and easily identified and whose analysis was claimed to be accurate within 5 per cent. Only one of these, tritiated water, was a radioactive tracer. Radioactive tracers are easy to detect even in small quantities, but they require special handling and special equipment. Also, those that can be used together are limited because special equipment is required to separate emissions from the various tracers. Two of the original 13 tracers were eliminated in static tests to determine how accurately and precisely they could be analyzed, and to check on gross adsorption. The remaining 11 were flowed through a 9-ft linear sandstone model, and breakthrough-elution curves were obtained. Finally, three tracers were field-tested as breakthrough tracers. These tests are described in the following sections. The 13 tracers considered in these experiments were EDTA (ethylene diamine tetra acetic acid), fluo-rescein, picric acid, salicylic acid and ammonium, boron (as borate), bromide, dichromate, iodide, nitrate and thiocyanate ions, plus chloride ion and tritiated water. All but the chloride ion and tritiated water were subjected to static sand tests to eliminate the tracers that could not be analyzed quickly and accurately and to eliminate those that showed excessive adsorption. All but two of the tracers, EDTA and salicylic acid, qualified for flow tests on this basis. The procedures used in the static tests (see Appendix A for analytical details) were as follows. Each tracer (in the amount shown in Table 1) was dissolved in 1,000 ml of water. Then, 800 ml of this solution was added to 500 gm of sand, and the remaining 200 ml was reserved as a control standard. The sand-tracer mixture was agitated once a day over a 10-week period, and during this period we analyzed five duplicate samples from this mixture, along with five duplicate samples from the control solution. From the control-sample analyses, we constructed a control chart on which the sand-tracer analysis results were plotted. The control chart, and its use to determine accuracy and precision of analytical results, as well as the amount of adsorption, is described in Appendix B. The results of the static tests are summarized in Table 1, which lists the concentration c (concentration at time t) divided by c, (initial concentration). If there was no adsorption, c/c, = 1. The acceptable deviation from this value varied from tracer to tracer, depending upon the limits of analytical precision established for the different tracers. The best results were obtained with boron, bromide and dichromate, with all values falling within limits of accuracy and precision. Ammonium, iodide, nitrate and picric acid also were satisfactory, although the ammonium results were erratic. Flourescein and thiocyanate were unsatisfactory ini-

By D. H. Davis, I. Fatt

Oil bearing rocks, usually found at depths of 2,000 to 10,000 it, are elastically deformed by overburden pressure. Although the change in porosity with pressure in a number of example rock.: has been shown to be small, it was thought that overburden pressure might have a significant effect on permeability. This note presents results of an investigation to determine the magnitude of the change in permeabilty with pressure. In routine core analysis permeabilities are measured on rock samples which are not under overburden pressure. If permeablity measured in this way differs from permeabilities measured under overburden pressure, a systematic error is introduced into well productivity calculations. The experiments described in this report were made to determine the magnitude of the change and thus to give an estimate of the error introduced into the calculations. The error introduced by the neglect of the change in permeability when overburden pressure is removed may account for part of the difference between well productivity calculated from core analysis and the actual well productivity. The results obtained in this investigation have only quali-tative significance because of the difficulty in reproducing in the laboratory the stress conditions on the rock buried in the earth. The assumption which is usually made is that the rocks in the earth are under a uniform pressure equal to the weight per unit area of the vertical overburden column from the rock in question to the surface of the earth less the pressure of the liquid in the pores of the rock. For an overburden consisting of sandstones and shales (of assumed average specific gravity of 2.3) and for a liquid pressure equal to the pressure in a salt water column (of specific gravity 1.0) reaching from the rock to the surface, the resulting net pressure on the rock is approximately 0.56 psi per ft of depth. EXPERIMENTAL METHOD Clean, dry sandstone core plugs one in. in diameter and about three in. long were mounted in a copper foil jacket as shown in Fig. 3 or molded in a Lucite jacket as shown in Fig. 4. All cores except those labeled "2" in Fig. 1 and "8" in Fig. 2 were measured in the copper foil jacket. Cores "2" and "8" were measured in the Lucite jacket. The jacketed core was placed in a high pressure hydraulic bomb in which the liquid pressure outside the jacket could be raised to 15,000 psi. Flow lines from the core were brought out of the bomb through special fittings in the bomh head and connected to a laboratory type gas permeameter. Measurements were made with nitrogen gas; the maximum mean gas pressure in the core was 16.1 psia. RESULTS The specific permeability of sandstone decreases with in. crease in overburden pressure. Most of the decrease takes place over the range of zero to 3,000 psi overburden pressure. If the net pressure on the rock is assumed to be 0.56 psi per ft of depth as discussed above, 3,000 psi of overburden pressure is equivalent to about 5,000 ft of overburden. At 3,000 psi overburden pressure, the permeability of the eight sandstone core samples tested ranged from 59 to 89 per cent of the permeability without overburden pressure. Figs. 1 and 2 show the permeability reduction as a function of overburden pressure. The permeability of the eight cores without overburden pressure ranged from 4.35 md to 632 md; these permeabilities are listed in Figs. 1 and 2. REFERENCES 1. Carpenter and Spencer: "Measurements of Compressibility of Consolidated Oil Bearing Sands," U. S. Bureau of Mines, R.I. 3450, (1940). * * *

Jan 1, 1952

By Henry M. Howe

THIS meeting was held at the home of the Institute in the United Engineering Society Building, 29. West 39th St., New York, N. Y., Feb. 18 to 21, 1908. The first session, held in the large auditorium Tuesday evening, Feb. 18, was called to order at 8 p.m. by Prof. Henry M. Howe, Past-President of the Institute, who welcomed the members and guests in a few cordial and well-chosen remarks. The following papers, accompanied by lantern-illustrations, were presented in oral abstract by their authors Swedenborg and Humboldt, by R. W. Raymond, New York, N. Y. Electric Power in Steel Mills, by David B. Rushmore and Karl A. Pauly, Syracuse, N. Y. At the close of the session, an informal reception in the offices of the Institute was tendered to members and guests. The second session, held in Assembly Room No. 1 in the same building, Wednesday, Feb. 19, was called to order at 10 a.m. by Prof. Robert H. Richards, Past-President of the Institute. Before proceeding with the papers on iron and steel, which were scheduled for presentation at this session, Mr. F. E. Junge, a representative of the gas-engine and electric motor industry of Berlin, Germany, gave a short oral discussion of the paper by Mr. Rushmore and Mr. Pauly, Electric Power in Steel Mills. Printed copies of the paper, Uniform Nomenclature of Iron and Steel, were distributed among the members and guests present, and the request was made for a later discussion of this important subject by letter. This paper constitutes the Report of Committee No. 24, of the International Association for Testing Materials, which was presented at the Brussels Congress in 1906. The following paper was presented in oral abstract by the author

Mar 1, 1908

By Robert T. Hill

The successful completion, January 10,1901, by Capt. A. F. Lucas, of a well, near Beaumont, Texas, whereby an enormous flow, estimated at '75,000 barrels a day, was obtained, opened a new oil-field in the United States, kindled a frenzy of exploitation and speculation, revolutionized the fuel industry of a large region, and brought gain to thousands of people. Even to-day, it is impossible to cast up the present results or to prognosticate the future influence of this event. It has caused the revival of attention in other localities where oil had been suspected, and exploration for oil throughout the Texas region. It has attracted notice to the mineral resources of the Texas region, and created an interest in the geological conditions of that great State. This State, which has increased in population and wealth, as recorded by every succeeding census, with leaps and bounds such as are exhibited by no other part of the Union, now stands fifth in population and first in productive wealth per capita. Its fields, pastures, forests and mines teem with raw material. The whole economic evolution of the State has gravitated toward a focal point where these products were available for the coming of the kiln, the machine and the factory. The only drawback to the prosperity of the State was the lack of an economic fuel, inferior coal costing an average of $5.00 per ton at the time of the Beaumont discovery. This

Jan 1, 1903

By Amitava Gangulee

A recent investigation has shown that solid solution hardening is almost absent in the quasibinary system SnTe-pbTe.1 The lack of solid solution hardening was attributed to the small difference of only about 3 pct between the atomic sizes of lead and tin, and to the fact that the formation of these solid solutions involved changes only in the sublattice occupied by the lead and tin atoms. The investigation reported here is concerned with the quasibinary system PbSe-PbTe which, similar to the SnTe-PbTe system, forms a continuous series of solid solutions2 and has the same NaC1-type (Bl) structure. The size difference between the selenium and tellurium atoms, however, is slightly larger than 7 pct. No indication of any ordering of the lead and tin atoms at. selected compositions had been found in the system SnTe-PbTe, which had been explained by the weak second-nearest-neighbor interactions between lead and tin atoms.' The possible occurrence of an ordering transition in the system PbSe-PbTe was also investigated in the present work. Polycrystalline specinlens of PbSel-1-xTex (x = 0, 0.20, 0.25, 0.33, 0.50, 0.67, 0.75, 0.80, and 1.0) were prepared by melting appropriate amounts of 99.999 pct pure Pb, Se, and Te j.n evacuated and sealed Vycor capsules. The capsules were quenched in water. The solidified ingots were homogenized at 800°C for 14 days. Chemical analysis of the homogenized ingots showed that the deviations from the stoichiometric compositions were less than 0.1 at. pct for each component. Part of each ingot was ground to pass through a 75 g sieve and pressed into 25.4 mm by 12.7 by 2 mm briquettes. Duplicate sets of specimens, each containing at least one briquette and part of the ingot of each composition, were sealed in evacuated Vycor capsules. Both sets were annealed at 500°C for 7 days; one set was quenced in ice-water and the other was cooled to room temperature over a period of 14 days.

Jan 1, 1970

By Leonid V. Azároff, H. N. Murty

In the course of investigating the soft X-ray absorption spectra of Ni-A1 alloys, Das and ~zfiroff' observed an anomalous brittleness in solid solutions containing 3 to 5 at. pct Al. The brittle alloys also had anomalously larger lattice constants' and the fine structure at the nickel K edge of an alloy containing 3.96 at. pct A1 unexpectedly resembled that of NiA1 more closely than that of a solid solution containing 5.51 at. pct Al. This led them to suggest the possibility that short-range ordering was produced during the homogenization anneal to which each specimen was subjected, similar to that observed in dilute solutions of vanadium and of chromium in nickel: as the principal cause of embrittlement. It was decided to repeat the above measurements on several alloys in this composition range in order to test the above hypothesis and to establish the effect of heat treatment on the alloys' properties. Three solid solutions in this range were prepared containing, respectively, 3.16, 4.00, and 4.54 at. pct Al, in addition to alloys containing 6 and 9 pct. All samples were annealed in vacuum at 1800°F for 100 hr and then furnace-cooled to room temperature, as in the original study. The lattice constants of these alloys are shown by open circles in Fig. 1 and can be seen to fit quite closely the curve established by the previously measured values, indicated by solid circles. (The experimental errors are of the order of the size of the circles, +o.oo~R.) The three alloys containing 3 to 5 at. pct A1 were found to be quite brittle, as previously reported. In order to test the possibility of ordering, these three solid solutions were again heated to 1800°F and, following a few hours at that temperature, were quenched directly to room temperature. All three alloys lost their brittleness. In order to verify the proposed ordering hypothesis, it was decided to subject each sample to several cycles of quenching and annealing (disordering and ordering). After some experimentation, it was established that reproducible results could be obtained by anneal-

Jan 1, 1968

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft, elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit, which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 1b.-pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 1/2 miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in Fig. 3. The two five-cylinder vertical Diesel engines, which are rated at 1,250 b.hp. at sea level, have cylinders of 525-mm. diameter (20.6 in.) and

Jan 1, 1917

By C. O. Burgess, A. B. Kinzel

Although vanadium is an important constituent of almost every brand of high-speed steel manufactured today, little is known as to its role in this series of alloys. The now standard 18 per cent tungsten and 4 per cent chromium constituents were the result of developments and improvements before 1903. In that year, vanadium was added to the steel by Dr. J. A. Mathews. This proved to be an outstanding contribution, so that the standard high-speed steel of today is generally referred to as the 18-4-1 type—18 per cent W, 4 per cent Cr and 1 per cent V. Various modifications have been attempted since then, but with the exception of the introduction of cobalt, no striking improvements have occurred. Vanadium has been increased to 2 per cent in many of the common brands, and at least one brand contains 5 per cent V in addition to the usual tungsten and chromium. The carbon has been gradually increased so that it is not uncommon to find 0.80 per cent in the standard grade, although the carbon in the 5 per cent vanadium steel mentioned above is approximately 1 per cent, and even 1.2 per cent has been made experimentally. The role of vanadium has never been well understood, and although vanadium has been increased to 2.5 and even 5 per cent in certain high speed steels, it has not been generally established that the higher vanadium contents result in superior cutting properties. However, in all of the investigations, of which the writers are aware, the interrelation of the vanadium and carbon contents was not considered as a prime factor. The carbon content was held at 1.2 per cent or less—generally at the usual 0.65 to 0.75 per cent. Theoretical Aspects Although the role of vanadium is not understood, there are theoretical considerations which indicate definite reasons for the improved cutting effciency due to vanadium. Refinement of the secondary grain is one distinct possibility. The well-known action of vanadium in limiting grain size might well be expected to operate in high-speed steels, and even though its action were not evident in the parent austenite grain.

Jan 1, 1932