Search Documents

William Kelly, Vulcan, Mich.:—In the northern part of Bedford county, Pa., the county immediately south of Huntingdon, the Clinton measures appear along the eastern slope of Tussey mountain near its base. The only iron-ore bed that has been worked is in the upper part of the formation. Along the mountain this seam has a dip of more than 60°. At the outcrop the ore is soft and rich, but with depth it passes often abruptly into an almost pure limestone similar to that described by Dr. Rutledge. The soft ore extends deeper in the cross-gullies than it does under the higher gound between the depressions. The slates adjoining the rich ore have been weathered, but where in juxtaposition to lean ore and limestone they are hard. The alteration of the ore-bed is evidently the result of the conditions of drainage in quite recent geo-

Jan 1, 1910

By G. W. Thomas

A simplified mathematical model of underground conduction heating in a system of limited permeability is presented. The model applies to underground retorting of oil shale, or to reservoirs containing extremely heavy oils. We assume that heat is introduced at a constant rate into a horizontal fracture which communicates between wells. The radial temperature distribution along the fractured surface is approximated by a step-function. Heat transfer away from the fracture is assumed to be by vertical conduction, and all convection effects are neglected. The model also takes into account the possible temperature dependence of thermal conductivity. A general expression for calculating the growth of the step-function temperature distribution with time is derived. The use of this expression and solutions to the one-dimensional heat equation make it possible to construct isotherms. Expressions for calculating .oil recovery, well spacing and heat efficiency are also given. An example calculation is presented for the conduction heating process in oil shale. Finally, the effect of the heat transfer coefficient between the gas and the fracture boundaries is investigated. INTRODUCTION Thermal recovery processes of oil recovery fall into the four general areas of hot fluid injection, forward combustion, reverse combustion and conduction heating. The first three of* these processes have been rather extensively studied in the past decade from both the experimental and theoretical points of view. As a result, it is possible to make reasonable engineering predictions and analyses of these processes. Little attention has been devoted, however, to the conduction heating process other than to note its possible utility.I To a certain extent, conduction heating cannot be divorced from the other regimes cited above, insofar as these provide the source of heat energy. In the conduction heating process, heat is introduced (either by combustion in the forward or reverse mode or by hot fluid injection) into a small fraction of the total reservoir thickness. This fraction may be either a streak of high permeability or an interwell fracture. Heat penetrates by conduction into the adjacent, less permeable regions of the oil-bearing rock, where the direction of conduction is essentially perpendicular to the streak or fracture. The heated product then drains by gravity or is gas driven to production wells. Conduction heating is probably most applicable to systems containing immobile bitumens such as tar sands and oil shale deposits and perhaps to low-permeability reservoirs containing highly viscous crudes. The mechanism also acts in combination with other thermal processes where fingering or overriding of a bed occurs. It seems probable that in at least one field test, conduction heating of this type was very influential.2 In this presentation we give a first approximation to some of the quantitative aspects of conduction heating. Marx and Langenheim3 treated a similar problem where they focused attention upon the injection interval, which spanned the total reservoir thickness. In their model, conduction heat losses to the bounding media imposed a practical limit on the calculated heated area. In the present study, however, we shall confine the injection interval to a small fraction of the reservoir thickness and assume it has no heat capacity. We therefore direct our attention to regions outside the injection interval into which the conduction of heat is beneficial. In particular, we will endeavor to locate specific isotherms in the media bounding the injection interval. Furthermore, we will construct our model to allow the thermal conductivity to vary arbitrarily with temperature. Thus the model will be applicable to underground retorting of shale where variations in thermal conductivity may be important. THEORY We consider the rock matrix to have no or, at best, a very limited permeability; consequently a

Jan 1, 1965

By D. J. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent papers. 1.2.3.1 In those papers references were also given to the work of Haigh in 1917.6 Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper .2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and nonferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

Jan 1, 1928

By H. Scott

Since Bohler discovered, in 1903, on cooling certain alloy steels, the phenomenon of a new and lower temperature transformation than the usual Ar 3-2-1 obtained by increasing the maximum temperature to which the material was heated, much has been published1 connecting this phenomenon with a large number of dissimilar steels of high alloy content. From the fact that the transformation divides itself, taking place at two widely separated temperatures, it has been called a "split transformation." The significant facts established by recent investigators2 are: that when the transformation occurs at the higher temperature Ar1, troostite or a decomposition product is formed, and that when the transformation occurs at the lower temperature Ar", the resulting structure is martensite. The terminology Ar' and Ar" adopted here is that of Portevin. Previous Investigations Reviewing the work on this subject published in a recent issue of Revue de Metallurgie and referring in particular to his statement that martensite is a solution of carbide in alpha iron, Le Chatelier says :4 "How then can a theory already 20 years old demand new investigations? The reason for it is that we have not succeeded in proving directly the real presence of the transformation of iron during the very short duration of the quenching. The fall of temperature takes place at the rate of several hundred degrees per second and the observation of

Jan 1, 1920

By John A. Emery, Frank G. Snyder

Mining geology has a threefold objective: to guide prospecting for new ore, to evaluate known orebodies as development risks, and to supply the detailed knowledge of ore structures necessary for more economical extraction. The role of geology in exploration is well established. This article will deal solely with orebody evaluation and the application of geology to development and mining problems as practiced by St. Joseph Lead Co. in the southeast Missouri district, which for many years has supplied approximately 30 pct of U. S. lead production. The primary concern of the present discussion is geology in the district, not geology of the district. The southeast Missouri district, locally called the Lead Belt, includes parts of St. Francois, Madison, and Washington counties. The first recorded mining was about 1720 at Mine La Motte in Madison County on surface showings of lead ore. Later discoveries near Bonne Terre, twenty-five miles to the north, led to extensive prospecting and underground mining. To date the district has yielded well over 8 million tons of pig lead, valued at more than $1 billion. By far the greater part of the lead production has come from an area of 50 sq miles, centering Fig. 1-Central portion of southeast Missouri on the city of Flat River, as shown in Fig. 1.

Dec 1, 1956

By W. F. Baldwin

The timing circuit generally employed in Carter Reservoir Behavior Analyzers consists of a synchronous motor driven cam which actuates a microswitch. A mechanically actuated timer of this type has several inherent disadvantages, among which are the following: 1. The first time interval may not be of uniform length, depending on the exact position of the cam at the conclusion of a previous run. 2. The positioning adjustments on the microswitch lever arms are critical and require periodic readjustment. 3. The mechanical system is subject to wear which will ultimately impair its accuracy. It was therefore considered desirable to devise an alternate method which would eliminate these difficulties without introducing others that would be equally troublesome. This note describes the design of an electronic timing device which has been incorporated in the analyzer constructed by the Field Research Laboratories of Magnolia Petroleum Co. The electronic timer circuit is built around a simple neon glow tube relaxation oscillator, the complete circuit diagram of which is shown in Fig. l. The operation of the circuit is as follows: Condenser C, is charged to the critical firing voltage of the neon glow tube VR-75 by battery B1 through resistors R1 and R2. When the neon glow tube fires, the condenser C, is discharged, The charging cycle then repeats itself,

Jan 1, 1950

By W. J. Romanow

RECENT papers by Williams, Sherwood, and Boothby,1 Seybolt et al.2 Heikes; and Roberts4 attest to the increasing importance of the hexagonal ferromagnetic compound MnBi. Since the magnetic properties of MnBi crystals are highly anisotropic, it is useful and necessary to have appropriate aids for determining their orientations—a (00.1) standard stereographic projection and a corresponding table of crystallographic angles for this structure. The tables of crystallographic angles for the hexagonal system available in the literature5 are computed for c/a ratios greater than that of MnBi and cannot satisfactorily be used to find the crystallographic angles of MnBi. A table of angles between the crystallographic planes (HK.L) and (hk.1) was calculated for MnBi from the formula0 F=are cos Hh+Kk+ 1/2(Hk+hK) + 3/4 (a/c)2Ll/v(H2 + K2 + HK + 3/4 (a/c)2L2) (h2+ k2+hk + 3/4 (a/c)2l2) on an IBM Type 650 Magnetic Drum Data Processing machine. The lattice constants used are listed in Table I and are those determined by Willis and Rooksby7 at 20°C. More recently published values obtained by both X-ray and neutron diffraction"' show no difference from these significant to the calculation. From the crystallographic angles between the basal plane (00.1) and the general plane (hk.1) in Table I, an (00.1) standard stereographic projection was made for MnBi which is shown in Fig. 1. Acknowledgments The author wishes to thank R. G. Treuting and J. N. Hobstetter for their technical assistance, and Miss D. P. Booth for programing the IBM machine for the calculations. He appreciates the opportunity to read the paper of B. W. Roberts of General Electric Co. prior to its publication. References 1H. J. Williams, R. C. Sherwood, and 0. L. Boothby: Bulletin Amer. Physical Soc., 1956 vol. 1, p. 132. 2 A. U. Seybolt, H. Hangen, B. W. Roberts, and P. Yurcisin: AIME Trans., 1956, vol. 206, p. 605: Journal oF Metals, May 1956. 3R. R. Heikes: Physical Review, 1955, vol. 99, p. 446. .B. W. Roberts: A Neutron Diffraction Study of the Structures of Manganese B.W.Roberts:ANeutronDiffractionBismuthide, Physical. Review, 1956, vol. 104, p. 607. 5 A. Taylor and S. Leber: AIME Trans., 1954, vol. 200, p. 190; JouRNal of Metals February 1954. « C. S. Barrett: Structure of Metals, 2nd Ed., p. 635. McGraw-Hill Book Co. New York and London, 1952. 7B. T. M. Willis and H. P. Rooksby: Proceedings Physical Soc., London, 1954, vol. 67B, p. 290.

Jan 1, 1958

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

LITTLE information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger's,1,2 Kick's: and Bond's' theories. Theories by Bond and Wang," Lineau," Hatch,' Roller,' and others0-11 were not considered applicable. Those used in this investigation may be expressed mathematically as follows: Rittinger Theory E = KrS2, pet,—--------------- [1] 40 d1 d0 Kick Theory TV 1 1 E = =K, [S pct. log1/d+ 100 log d0] [2] 40 d1 L. L. FELTS, Junior Member AIME, was formerly a Graduate Assistant, University of Illinois. G. B. CLARK, Member AIME, was formerly Professor of Mining Engineering, University of Illinois, and is now Chairman, Dept. of Mining Engineering, Missouri School of Mines and Metallurgy. J. YANCIK, Junior Member AIME, is a Graduate Assistant, Missouri School of Mines and Metallurgy. This paper, TP 4213A. is revised from a thesis submitted by L. L. Felts in partial fulfillment of the M.S. degree in Mining Engineering, University of Illinois, 1954. Discussion may be sent (2 copies) to AIME before May 31, 1956. Manuscript, Dec. 27, 1954. Bond's Third Theory E = Kb [S pct. log1/d1+ 100 log d0] where E — energy used in breakage, d, = average diameters of screen fractions of broken cement particles, pct, = percent weight of diameter d;, and 2 pct, = 100 pct. The above equations were employed to determine values of Kr, Kk, Kb for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement. Knowledge of the failure of solids under static loads is developing very rapidly. Their failure under impact loads has been investigated and reported in the literature only to a limited extent. Theories of failure' hnder static loading include 1) the maximum stress theory, 2) the maximum strain theory, 3) the theory of constant elastic strain, 4) theory of maximum shearing stress, and 5) Mohr's theory of strength. All of these have elements of usefulness in establishing an applicable theory for blasting. For highly strained and compressed material such as that surrounding a detonating charge of high explosive, the Mohr theory and its implications appear to be the

Jan 1, 1957

By J. W. Borough

THE electrical conductivity of pure copper is markedly decreased by small amounts of impurity in solution. The magnitude of this effect has been very carefully determined by numerous investigators who studied a wide variety of impurity elements. Much of this work is summarized in an excellent review by Pawlek and Reichel.' The case of zinc impurity in copper is an exception to the above in that there has been no well-documented study of the effect using high-purity starting materials. The values for the effect of zinc on conductivity, which are usually taken from unpublished work by Skowronki, indicate that zinc in low concentration has no effect whatever in lowering the conductivity of pure copper. This effect, if true, is unusual since it is generally known that even in lowest concentration, impurities exert an effect on conductivity which is proportional to the amount dissolved. It is more reasonable to suspect that in the original work on the effect of zinc some of the zinc was oxidized out of solution during specimen preparation. The following experi- and calculated d-spacings based on the unit cell dimensions of Baenziger et al. Since the single crystal studies of Baenziger et al. were limited to (hk0) and (hk 1) data, it was not possible to Compare all the intensities of the powder and single crystal patterns. However, the strongest reflections of both studies, the (321) reflection, agree very well when the appropriate multiplicity factor is used. Good agreement was also found in a number of other reflections of lesser intensity. Despite the precautions taken in annealing the U6Fe powder, an appreciable amount of UO, was detected in the powder pattern after heat treatment. The powder pattern reported by Groganoand Clews is given in Table I. Except for the 3.15A line, which is the strongest line of UO,, their pattern, as far as it goes, compares favoEably with the data from this study. Gordon and Kaufmann have reported a diffraction powder pattern purported to be U, Fe but it bears very little resemblance to the patterns of Table I. ments were carried out to redetermine the effect of zinc on conductivity using high-purity starting materials and processing conditions capable of producing oxygen-free alloys. Materials used in the experiment were ASR 99.999 pct Cu and Cumingo 99.999 pct Zn. Four 1 lb melts were prepared with identical procedure in argon atmosphere with crucibles made from Speer No. 580 graphite. The compositions were 0.0, 0.1, 0.3 and 1.0 pct Zn. Standard No. 14 wire (0.064 in. diam) was made from these melts as follows. The 1 pct Zn sample was first reduced 94 pct by cold swaging with five annealing treatments of 800o for 10 min in hydrogen between swagings, and then reduced 94 pct to the

Jan 1, 1962

By W. D. Von Gonten, R. L. Whiting

Regression analysis was used to correlate the physical properties of 478 sandstone and 90 carbonate core samples. Porosity, permeability, electrical formation resistivity factor, capillary pressure and the sonic velocity of the shear and compressional waves were measured. Prediction equations for porosity, permeability and electrical formation resistivity factor were found which should be useful in understanding the relationships between the physical properties of porous media in formation evaluation. INTRODUCTION The physical properties of porous media are important to the petroleum engineer and geologist. To evaluate fully the potential and behavior of a subsurface formation such as a petroleum reservoir, certain physical properties of the porous medium must be known. The problem of accurately determining physical properties of subsurface formations has not been solved because many determinations must be made by indirect measurements and because of the difficulties caused by complex pore structure and presence of clays in most naturally occurring porous media. Due to the difficulty in measuring some of the physical properties of porous media, it would be advantageous to be able to predict a certain physical property of a rock from other physical properties of the rock which could be measured more easily and more accurately. Since most potential reservoir rocks are heterogeneous, relationships between the physical properties are very complex and thus far no satisfactory correlations based on theory or laboratory models have been developed. It appears that empirical relationships obtained by measuring the physical properties of a large number of samples of naturally occurring porous media and applying regression analysis to develop equations for one physical property in terms of other rock properties is the best approach. REVIEW LITERATURE The three physical properties used as dependent variables for correlating purposes were porosity, permeability and formation factor. Since formation factor is more difficult to determine, a brief review of the literature is provided on this property. The first work on determining formation factors was published by Archie1 in 1942. He defined this property of a porous medium as F - Ro/Rw......(1) where Ro is the resistivity of the porous medium when completely saturated with a brine of resistivity Rw. Archie found the best correlation between formation factor and porosity was the following equation, where is the porosity fraction and m is the constant characteristic of the rock. The value of m was 1.3 for unconsolidated sand packs, and ranged from 1.8 to 2.0 for consolidated sandstones. In 1950 Patnode and Wyllie2 and De Witte3 observed that the formation factor as determined by Eq. 1 was valid only when the porous medium contained no conductive solids such as clay or shale. When conductive solids are present the formation factor is also dependent on the resistivity of the saturating fluid. Therefore, in samples containing conductive solids the formation factor decreased as the resistivity of the saturating fluid increased. Because of this. the measured formation factor was called the apparent formation factor and was designated Fa. Patnode and Wyllie proposed the following equation,

By William F. Harris, Joseph Easha

FOR many years basic control of refinery operations depended on visual observation of small chill specimens poured at various intervals during processing. The oseto of these samples was related to the physical and chemical properties of the metal. Since the =setn is dependent on many factors other than oxygen content, this method, while giving a general indication of the condition of the copper, does not accurately measure the oxygen content. For the last 3 years a modified vacuum fusion procedure which enables the operator to determine the oxygen content of the copper within 1 5 min of sampling has been in use at the Westinghouse Copper Mill. For use with this apparatus a sampling technique has been developed which gives oxygen values representative of the oxygen content of the wire bar. The sampling technique is based on a statistical study, which compared the oxygen content of the laboratory sample of copper poured at the same time a wire bar was being poured, with the oxygen content of the wire bar. The apparatus used for the determination of oxygen in copper is shown in Fig. 1 and is essentially the same as previously described but with one important modification. A very porous fritted glass disc has been inserted in the tubing between the manom- eter and 40/50 ground glass joint. The fritted disc retains the copper vapor and copper particles in the furnace section and prevents contamination of the mercury in the manometer. Without the disc the manometer became difficult to read after a few weeks of operation. In earlier work1 it had been established that the simplified vacuum fusion apparatus used at the Copper Mill gave essentially the same results as a con-vential vacuum fusion apparatus. However, for this study it was necessary to determine the difference, if any, between the oxygen content of the wire bar and the oxygen content of the small chill sample used for the oxygen analysis. This correlation was established by taking a chill sample at the same time wire bars were being poured. The wire bar being poured at the time the chill sample was taken was marked and removed for further analysis. The copper is sampled at various times during refining and cast into laboratory size samples with the mold shown in Fig. 2. The mold is made of cold rolled steel and is 2 in. high and 2 1/2 in. in diam. The large upper portion of the cast sample is used for measurement of the conductivity of the copper, The lower portion which is a rod about 1/4 in. diam by 3/4 in. long is used for determination of the oxygen content. This portion of the sample weighs about 5 g which is approximately the size sample used for the analysis. The only preparation neces-

Jan 1, 1962

By Kenneth L. Cook

THE five serpentine masses exposed within the northern half of Riley County, Fig. 1, constitute a major part of the few exposures of igneous rock in Kansas.' Although not many subsurface data are available for this part of Riley County,2 six deep wellsV indicate that the basement complex lies between 2500 and 3000 ft below the earth's surface. A northwestward-trending ridge in the present basement surface, which extends across the northern half of Riley County, is indicated on Mettner's contour map.' The serpentine masses lie in a region that was active during Pennsylvanian and Permian time along two main tectonic trends, which may, in part at least, have developed contemporaneously." One trend is northeasterly, as evidenced by the Nemaha anticline, the Abilene anticline, the Voshell anticline, and many other smaller northeastward-trending folds. The other trend is northwesterly, as evidenced by the central Kansas uplift, the Salina basin syncline, and smaller northwestward-trending folds. The area of the Abilene anticline was actively deformed during much of this time, and the present surface rocks, for the most part Permian in age, show many normal faults." The Bala and Leonardville intrusions lie within a mile of the axis of the Abilene anticline, Fig. 1, as mapped by Wallace Lee;' the Randolph No. 1 and Randolph No. 2 intrusions lie within about 5 miles of the axis; and the Stockdale intrusion lies within about 8 miles of the axis. The igneous rocks have intruded horizontal or gently dipping limestones and shales that are late Permian in age.V he period of intrusion, according to Moore and Landes, was probably Cretaceous.' At present a detailed description of the petrography is available for only the Bala intrusion. Moore and Haynes' describe the rock at Bala as a green, serpentinized, porphyritic, peridotite breccia containing inclusions of shale. The ground mass consists chiefly of serpentine and calcite with considerable chromite (5 to 10 pct) and some magnetite. The phenocrysts consist principally of altered olivine with some altered augite and biotite. Although probably different in petrographic details, all the serpentine masses are somewhat similar in that 1) they consist of a dark green, fine-grained ground mass of igneous rock containing many xeno-liths composed of fragments of the neighboring sedimentary rock; 2) they tend to form small mounds on the landscape, thus indicating their greater resistance to weathering and erosion; and 3) they are magnetic. Previous Magnetic Survey of the Bala Intrusion: To the writer's knowledge, only the Bala intrusion had been surveyed with a magnetometer prior to the magnetic surveys discussed in this paper. Dreyer8 interprets the intrusion as a vertical, eastward-plunging dike, on the basis of the results of his magnetic survey, Fig. 1, with a vertical magnetom-

Jan 1, 1956

By N. K. Chen, R. Maddin, K. T. Aust

Lattice rotations occurring on the tension and compression sides during the bending of molybdenum single crystals at room temperature were followed in detail. Observations were also made concerning crystallite rotations and slip traces. &apos;The results indicated the participation of (110) as slip planes and the<111>as slip directions. Crystallite fragmentation during bending was also noted. EVERAL investigations have been conducted on pure bending of face-centered cubic metals.&apos;-" Structural changes as a result of "bend-gliding," and the importance of bending and constraints during conditions of axial stressing, have been noted.&apos;," It was evident that the mechanism by which the bending deformation occurs is more complex than the case of simple shear. Studies of the bending of body-centered cubic metals from the aspect of the crystallographic mechanism appear to be lacking. Molybdenum single crystals therefore were subjected to deformation by bending in order to determine the reaction of the body-centered cubic lattice to bending stresses. It might be expected for the bending of single crystals that lattice rotation as represented by the axis of compression would proceed toward the pole of the active slip plane and that rotation of the tensile stress axis should indicate the slip direction.&apos; It was believed therefore that a study of the tension and compression sides of bent molybdenum single crystals should give data concerning the operative slip system. Specific problems which are pertinent to the overall picture of plastic deformation were also investigated, e.g., whether the constraints offered by pure bending give rise to the deformation band, and also the nature of the asterism occurring on the tension and compression sides during the stages of deformation. Experimental Procedure Eight single crystal specimens were grown from sintered molybdenum rods 143 in. diameter using the method described previously.6 The purity of this material was reported as 99.9 pct as described elsewhere.&apos; The specimens were % to 1/10 in. in diameter x 7 in. long, with single crystals approximately 1 to 2 in. in length occupying the entire center sections of each specimen. The specimens were elec-trolytically polished using an electrolyte of 300 cc methyl alcohol, 60 cc H2SO4, 130 cc HCl, and a current density of 4 amp per sq in. Each specimen was then loaded in a bending apparatus similar to that used by Yen and Hibbard,&apos; as shown in Fig. 1. The load was applied by means of a spring and screw arrangement through four ball-bearing surfaces set 1.5 in. apart. Either the inner two bearings or the outer two (A, B, Fig. 1) were attached to a movable steel plate (D) through which the load was transmitted. Since the apparatus was mounted on a track of the X-ray apparatus, the tension or compression side of the specimen could

Jan 1, 1954

By AIME AIME

IT is unlikely that any oil field has ever threatened the future course of the oil industry as does Kettleman today. It seems that nature has striven to outdo herself in combining in this field every possible factor conducive to a tremendous production of the petroleum product in greatest demand-gasoline. This field already has 13,700 acres of proved land and an oil zone of known thickness of 1400 ft. It has wells yielding several thousand barrels of oil of virtually motor fuel grade, together with millions of cubic feet of gas at almost unheard of pressures. The field would have been the. answer to an oil man&apos;s prayer in times of under-supply, but now it is the oil man&apos;s nightmare, for drilled in -the manner of most other fields and without regard to available markets for oil and gas, the greatest physical and economic losses in the his¬tory of the oil industry will result.

Jan 1, 1930

By J. E. Pavlick, W. W. Mullins, H. W. Paxton

The growth of nitrogen-austenite during nitriding of large-gvained ferrite between 650" and 800°C has been studied as a functimz oJ time and nitrogen potential of the atmosphere for a variety of alloying elements dissolved in the ferrite. Whereas no preferential grain boundary penetration by aistenite takes place in zone-refined iron, the addition of aboit I zot pct oj&apos; V, Ti, Cr. Si, or A1 produces significant protrusion of austenite down former 0-0 boundaries. This group of elernents also produces ragged y-0 interfaces in the a grains which advance more slozuly than those in zone-refined iron. 1 zut pct of Ni, Co, Mn, or Mo dissolved in ferrite leads to essentially smooth 7-a interfaces, which advance at rates very sinzilar to those in zone-refined iron. The reasons for this effect are not clear. Two possible limiting hypotheses, not necessarily exclusive, are discussed. One involves p.referentia1 grain bozindary diffusion of nitrogen. the other the production of a zone of ferrite, stpersatcirated with respect to nitrogen, from which austenite precipitates helerogeneozisly on the a-a gyain boundaries. In many phase transformations which occur by nu-cleation and diffusion-controlled growth, information on the parameters which control the rates of nuclea-tion and of growth is frequently not quantititative. The present work describes a continuation of efforts to obtain quantitative data on growth rates in systems where thermodynamic and kinetic factors are known independently, and thus where comparison with models of the growth process is possible. The work has been conducted on iron-base systems for two reasons. Firstly, there are several interesting transformations in this system, many of which are of practical importance. Secondly, the information on phase diagrams, activities, and diffusion coefficients is more complete in this system than in any other. These data are still inadequate to check all the effects of alloying elements, but at worst it is possible to make estimates and thus examine order-of-magni-tude agreement with proposed models. It will be necessary to do this in the present work. The problem studied was the growth of nitrogen-austenite in from the surface of large-grained columnar crystals of alloyed ferrite exposed to an NHs/Hz atmosphere. Earlier work by Grozier et al.&apos; had suggested that growth of austenite may occur preferentially along grain boundaries of alloyed ferrite, whereas zone-refined (ZR) iron shows no such effect, Fig. 1. Growth of nitrogen-austenite into single crystals of zone-refined ferrite is planar provided sufficient nu-cleation sites for austenite are present, and is controlled by volume diffusion of nitrogen through the

Jan 1, 1967

By Harold Margalin, Elmars Ence

M. H. Mueller, M. V. Nevitt, and H. W. Knott (Argonne National Laboratory)—We have reported1 the crystal structure of Ti2CU as body centered tetragonal with a. = 2.944A and co = 10.786A, six atoms per unit cell, and space groupl4/mmm(MoSi2 type). This cell is larger but definitely related to the unit cell reported by the authors. It permits definite positions for the titanium and copper atoms in the cell located as follows: 2 Cu (a) 0 0 0; 1/2 1/2 1/2 4 Ti (e) 0 0 z; 1/2 1/2 1/2 + z; 0 0z; 1/2 1/2 1/2- z where z = 0.341 The face centered tetragonal cell reported by the authors can be transformed to a small body centered tetragonal cell with flo (small bet) = ao(fct)v2 Both unit cells have the same CO. Neither the face centered tetragonal cell with four atoms per unit cell nor the small body centered tetragonal cell with its two atoms per unit cell lend themselves conveniently to an orderly arrangment of the 2 to 1 ratio of titanium to copper atoms. When the co of this small body centered cell is tripled, however, a large body centered tetragonal cell results with six atoms per unit cell as described above. We had also noted that the X-ray patterns of Ti2Cu indicated that the structure could be approximately described by the face centered tetragonal cell as reported by the authors; how- ever, there was evidence for a few additional very weak lines whose positions indicated a larger unit cell. Since the X-ray scattering amplitudes of titanium and copper are nearly equal, it is evident that it is difficult to distinguish their positions especially from X-ray powder patterns. It was therefore decided to look at a powder pattern obtained by neutron diffraction since the scattering amplitudes of the two elements are considerably different in magnitude and opposite in sign. The sample used for neutron diffraction was selected from a group of three alloys prepared by arc melting using crystal bar titanium of 99.92 pet nominal purity and 99.999 pet pure Cu. The alloys designated as A, B, and C had the following respective compositions: Ti-32.8 at. pet Cu, Ti-33.3 at. pet Cu, and Ti-33.8 at. pet Cu. On the basis of the melting losses incurred, it was established that the actual concentration of either component in any of the alloys probably did not deviate from the intended value by as much as 0.1 at. pet. The alloys were annealed for 5 days at 700°C in evacuated Vycor capsules and quenched in tap water. The metallographic structures of these alloys are shown in Fig. 1. None of the alloys contained sufficient second phase to permit its positive identification. Since alloy B contained the least amount of second phase and since its composition placed it closest to the ideal stoichiometry, it was chosen for the neutron diffraction study. The oxygen content of alloy B was found by chemical analysis to be 0.06 at. pet. This particular intermetallic compound is especially suitable for investigation with neutron diffraction since if the titanium and copper atoms have a random statistical distribution, a near null-matrix would result in which there would be practically no coherent scattering of neutrons, and hence no Bragg diffraction peaks. Such a condition could come

Jan 1, 1962

By R. S. McCaffery, D. E. Krause

There has been some discussion among blast-furnace operators regarding the relative merits of tuyeres of the converging type and tuyeres designed in an attempt to produce a diverging jet of air. An article1 on Progress in German Blast Furnace Practice indicates the interest in this subject abroad. This article illustrates a diverging type of tuyere which is shown here in Fig. 1A. The design appears to be rather poor as regards known properties of air flow. The adoption of this tuyere, the arlicle states, resulted in a decrease of blast pressure of about 4 Ib. per sq. in. and an increase of the output of the furnace. If the improvements mentioned are due entirely to the change in tuyere design, the subject of tuyere design seemed worthy of investigation and this paper is a report of such work. Because of the gain in efficiency brought about by the use of a diverging tuyere in the German plant, it was thought desirable to investigate the shape of the air streams issuing from various types of tuyeres to ascertain whether the gain was due to the tuyere itself or to the distribution of the air in the furnace. Since it is difficult to do experimental work on a full-sized furnace, or even on full-sized tuyeres, and because of the equipment available for the work, it was decided to carry out the work on scale models of tuyeres. Therefore, in this work, single tuyeres were used and the blast discharged into the atmosphere. The shape of the air stream was determined by means of a Pitot tube suitably supported in the air stream at various positions. The air was furnished by a Roots blower driven by a 10-hp. direct-current motor having field control, and capable of discharging 250 cu. ft. per min. with a pressure on the discharge of 4 in. of mercury. A modern blast furnace with 21-ft. hearth requires about 50,000 cu. ft. per min. of free air at from 16 to 23 Ib. per sq. in. pressure, depending upon the type of burden. This pressure is the total pressure required to force the air through the burden and through the tuyeres. Upon computation the pressure drop through the tuyeres is about 1 to 2 lb. per sq. in. By making the tuyeres to a one-fifth scale, and by using a pressure of 1.5 in. of mercury, the shape of the air streams should be

Jan 1, 1931

By Richard McCaffery

THERE has been some discussion among blast-furnace operators regarding the relative merits of tuyeres of the converging type and tuyeres designed in an attempt to produce a diverging jet of air. An article1 on Progress in German Blast Furnace Practice indicates the interest in this subject abroad. This article illustrates a diverging type of tuyere which is shown here in Fig. 1A. The design appears to be rather poor as regards known properties of air flow. The adoption of this. tuyere, the article states, resulted in a decrease of blast pressure of about 4 lb. per sq. in. and an increase of the output of the furnace. If the improvements mentioned are due entirely to the change in tuyere design, the subject of tuyere design seemed worthy of investigation and this paper is a report of such work. Because of the gain in efficiency brought about by the use of a diverging tuyere in the German plant, it was thought desirable to investigate the shape of the air streams issuing from various-types of tuyeres to ascertain whether the gain was due to the tuyere itself or to the distribution of the air in the furnace. Since it is difficult to do experimental work on a full-sized furnace, or even on full-sized tuyeres, and because of the equipment available for the work, it was decided to carry out the work on scale models of tuyeres. Therefore, in this work, single tuyeres were used and the blast discharged into the atmosphere. The shape of the air stream was determined by means of a Pitot tube suitably supported in the air stream at various positions. The air was. furnished by a Roots blower driven by a 10-hp. direct-current motor having field control, and capable of discharging 250 cu. ft. per min. with a pressure on the discharge of 4 in. of mercury. A modern blast furnace with 21-ft. hearth requires about 50,000 cu. ft. per min. of free air at from 16 to 23 lb. per sq. in. pressure, depending upon the type of burden. This pressure is the total pressure required to force the air through the burden and through the tuyeres. Upon computation the pressure drop through the tuyeres is about 1 to 2 lb. per sq. in. By making the tuyeres to a one-fifth scale, and by using a pressure of 1.5 in. of mercury, the shape of the air streams should be

Jan 1, 1931

By AIME AIME

MANY producers have held that the only workable quicksilver ore is easily recognized by its .cinnabar content. In most cases this is true. A noticeable exception is a. particular opalite deposit where part of the ore now being mined in considerable quantity shows only the yellow mineral, calomel, or its alteration products. This mineral, on exposure to the sunlight, quickly becomes coated with gray or black layers that may be removed by scraping to reveal the yellow mineral beneath. The blackening of this mercuric chloride on exposure to sunlight shows reaction to form metallic mercury, which is usually plainly present in this class of ore.

Jan 1, 1929

By George L. Atwood, William Brown

Phosphate ore is being mined at Monsanto Co.&apos;s Henry mine, near Soda Springs, Idaho, for the company&apos;s three furnace elemental phosphorus plant near Soda Springs. The finished product from the furnaces is elemental phosphorus which is subsequently used in the manufacture of detergents, food preservatives, fire retardants and other consumer items. In stripping and mining, D-9 crawler tractors are utilized to rip and push-load rubber-tired scrapers. The equipment consists of six D-9G crawler tractors, four Caterpillar 657B scrapers, eight Euclid S-24 scrapers, one Reich T750 drill and one Caterpillar No. 16 patrol plus various support equipment. Stripping is performed on a 12- month basis, two shifts per day, whereas mining is mainly in the summer months on a one-shift basis. The hauling season begins May 15 and ends November 1 due to freezing weather and snow conditions. Annual production is 1 million tons of phosphate rock and 2.5-3 million cu yd of stripping. Stripping, mining and hauling is performed for Monsanto by Dravo-Soda Springs, a mining contractor which owns, operates and maintains all equipment used. The contractor is paid for stripping by the bank yard and for ore mined and hauled on a tonnage basis.

Jan 8, 1972